Get In the event of a breakdown -> Tool kit Guide for Citroen Berlingo SUV Third Generation (2018-2025)

In the event of a breakdown

With 1.5 BlueHDi (Euro 6.2/6.3)

With spare wheel

The tools are located under the right-hand front

seat.

Running out of fuel

(Diesel)

► Switch on the ignition (without starting the

engine).

► Wait around 1 minute and switch oﬀ the

ignition.

► Operate the starter motor to start the engine.

If the engine does not start at the ﬁrst attempt,

do not keep trying, but restart the procedure.

To access the tools:

With Diesel engines, the fuel system must be

primed if you run out of fuel.

– With non-adjustable front seat, lift the seat

cushion by placing your hand between the

cushion and the backrest.

– With adjustable front seat, move the seat

forward as far as possible.

Before starting to prime the system, it is

essential to put at least 5 litres of Diesel into the

fuel tank.

Non-BlueHDi engines

For more information on Refuelling and

on Misfuel prevention (Diesel), refer to

the corresponding section.

The jack is located in the passenger footwell.

► Open the bonnet and then, if necessary,

unclip the cover to access the priming pump.

► Operate the priming pump repeatedly

until resistance is felt (resistance may be

felt at the ﬁrst press).

► Operate the starter motor to start the engine

(if the engine does not start at the ﬁrst attempt,

wait around 15 seconds before trying again).

► If the engine does not start after a few

attempts, operate the priming pump again, then

the starter motor.

Vehicle with Petrol or Diesel engine

With temporary puncture repair kit

The kit is located under the right-hand front seat.

With spare wheel

The jack is located under the right-hand front

seat.

For non-BlueHDi versions, the fuel system

components are located in the engine

compartment; this may be under a removable

cover.

The tools are located under the left-hand front

seat.

For more information on the Engine

compartment, in particular the location

of these components under the bonnet, refer

to the corresponding section.

List of tools

► Put the cover back in place and clip it in, then

close the bonnet.

With 1.6 BlueHDi (Euro 6.1)

► Switch on the ignition (without starting the

engine).

► Wait around 6 seconds and switch oﬀ the

ignition.

Tool kit

► For easier access, move the seat(s) forward.

► Repeat the operation 10 times.

► Operate the starter motor to start the engine.

If the engine does not start at the ﬁrst attempt,

do not keep trying, but restart the procedure.

Accessing the tools

Vehicle with electric motor

1. Chock to immobilise the vehicle

2. Removable towing eye

With temporary puncture repair kit

The tools are located in the passenger footwell.

202

In the event of a breakdown

Store the 12 V compressor and sealant

cartridge 4 inside the pouch as shown.

With spare wheel

3. Torx key

Allows the removal of the rear lamps in order

to change a bulb.

With temporary puncture repair kit

The space inside the passenger footwell is

narrow. In order to be able to close the hatch,

store the tools in their initial locations: chock

1 outside the bag, removable eye 2 on top of

the bag with the buckle facing outwards, Torx

key 3 on top of the bag, 12 V compressor with

sealant cartridge 4 inside the bag.

5. Wheelbrace.

For removing the wheel bolts and raising/

lowering the jack.

6. Jack.

Used to raise the vehicle.

7. Wheel bolt cover/wheel trim removal tool

(depending on equipment).

4. 12 V compressor with cartridge of sealant

and speed limit sticker

For more information about the Temporary

puncture repair kit, refer to the corresponding

section.

For temporary repair of a tyre and to adjust

the tyre pressure.

If present on the vehicle, used to remove

the wheel bolt covers on alloy wheels or the

wheel trim on steel wheels.

Storing the tools (vehicle with electric

motor)

8. Socket for "anti-theft" wheel bolts.

Used to adapt the wheelbrace to the special

"anti-theft" bolts.

For more information on the Spare

wheel, please refer to the corresponding

section.

203

In the event of a breakdown

All of these tools are speciﬁc to your

vehicle and may vary depending on

equipment.

power supply for long enough to repair a tyre

after a puncture.

Do not use them for any other purposes.

Only the 12 V socket located at the front

of the vehicle can be used to power the

compressor.

The jack must only be used to change a

wheel with a damaged or punctured tyre.

The jack does not require any maintenance.

The jack meets European standards, as

deﬁned in the Machinery Directive 2006/42/

EC.

For more information on the Tool kit,

refer to the corresponding section.

► Connect the pipe from the bottle of sealant to

the valve of the tyre to be repaired and tighten

ﬁrmly.

► Connect the pipe from the compressor to the

bottle of sealant.

► Check that the compressor switch is in

position "O".

► Fully uncoil the electric cable stowed under

the compressor.

Repair procedure

Some parts of the jack such as the

screws and hinges could cause injury:

avoid touching them.

Do not remove any foreign body

(e.g. nail, screw) which has penetrated

the tyre.

Carefully remove any traces of grease.

► Park the vehicle without obstructing traﬃc

and apply the parking brake.

► Follow the safety instructions (hazard

warning lamps, warning triangle, high visibility

jacket, etc.) according to the legislation in force

in the country in which you are driving.

► Switch the ignition oﬀ.

Temporary puncture

repair kit

► Connect the compressor's electric plug to the

vehicle's 12 V socket.

► Aﬃx the speed limit sticker.

Scan the QR Code on page 3 to view

explanatory videos.

► Remove the valve cap from the tyre to be

repaired, and place it in a clean place.

Made up of a compressor and a sealant

cartridge, it allows you to carry out a temporary

repair of the tyre so that you can drive to the

nearest garage.

It is designed to repair most punctures located

on the tyre tread.

The speed limit sticker must be aﬃxed

inside the vehicle in the area close to the

driver, to remind them that a wheel is in

temporary use.

► Switch the ignition on.

The vehicle's electric system allows the

connection of the compressor to the 12 V

204

In the event of a breakdown -> Tool kit for Your Citroen Berlingo SUV Third Generation (2018-2025)

Related Topics

In the event of a breakdown

Popular Owner Manuals

Latest Owner Manuals