Advertisement

Advertisement

DRIVING -> Anti-intrusion alarm for Your Citroen C6 4 Door Second Generation (2016-2023)

ANTI-INTRUSION ALARM  
DEACTIVATION OF THE  
ALARM USNG THE REMOTE  
CONTROL  
A
II  
The alarm is disarmed when you  
unlock the vehicle (with a press on  
button A on the remote control).  
DEACTIVATION OF THE  
ALARM WITH THE KEY  
Unlock the doors with the key. The  
siren triggers. Enter the vehicle,  
insert the key in the ignition and  
turn it to the drive position to stop  
the siren. Otherwise the siren  
will continue for approximately  
30 seconds.  
The installation also has a siren,  
and a warning lamp on the con-  
trol 1 which is visible from outside  
the vehicle, indicating the three  
possible statuses of the alarm:  
Your vehicle may be equipped with  
anANTI-INTRUSIONALARM. This  
provides:  
Exterior perimeter protection  
by means of detectors on the  
vehicle access points (doors,  
boot, bonnet) as well as on the  
electrical supply.  
Alarm not active (disarmed),  
warning lamp off.  
Alarm active (armed), the  
warning lamp ashes slowly.  
Alarm triggered (signalling an  
intrusion), the warning lamp  
ashes rapidly if the alarm is  
deactivated by a press on the  
control A. It stops as soon as  
you switch on the ignition.  
Interior volumetric protection  
by means of ultrasonic sensors  
(detecting movement inside the  
passenger compartment). This  
can be deactivated using the  
control 1  
Note: If there is a malfunction,  
the warning lamp remains perma-  
nently on.  
26  
ANTI-INTRUSION ALARM  
OPERATING THE ALARM  
First make sure all the doors are closed.  
The alarm is armed by pressing button B on the remote  
control.  
With the alarm armed, the protections are active after  
5 seconds (perimeter) and 45 seconds (volumetric).  
When the alarm is armed (on standby), any intrusion  
will trigger the siren for 30 seconds, accompanied by  
the direction indicators lighting up.  
The alarm then goes back on standby, but the trigger-  
ing remains memorised and is signalled by the rapid  
ashing of the warning lamp on control 1 after you have  
deactivated the alarm with a press on the unlocking  
button A. The ashing stops when you switch on the  
ignition.  
The siren is also triggered if there is a cutting of the  
electrical supply. To stop it, restore the electrical supply  
then press on the unlocking button A  
Note:  
Deactivating the volumetric detection  
You can operate the alarm with perimeter protection  
only, by deactivating the volumetric protection (if for  
example you wish to leave an animal in the vehicle).  
For this, switch off the ignition then immediately press  
button 1 for at least one second.  
The warning lamp on button 1 should come perma-  
nently on. It will start to ash when the alarm is armed.  
Arm the alarm by locking your vehicle with the remote  
control.  
It is recommended to deactivate the volumetric detec-  
tion when washing the vehicle in order to prevent the  
random triggering of the alarm.  
II  
Automatic activation (according to destination)  
The alarm is armed automatically, 2 minutes after the  
last door, or the boot, has been closed.  
In order to prevent the alarm from triggering when you  
open one of the doors or the boot, it is essential to press  
the unlocking button A again on the remote control.  
If you want to lock your vehicle without arming the  
alarm, just lock with the key only.  
If you lock your vehicle and a door, or the boot, is  
still open, the central locking does not operate but  
the alarm will arm itself after approx. 45 seconds.  
Note: The siren is automatically deactivated (for example  
for disconnecting the battery) as soon as the vehicle is  
unlocked using the remote control.  
A
B
27