2002-2014 Citroen C8 4 Door EASE OF USE and COMFORT -> Seats (Rear Side/Centre/Bench) User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

EASE OF USE and COMFORT -> Seats (Rear Side/Centre/Bench) for Your Citroen C8 4 Door Second Generation (2002-2014)

Seats  
Rear side seats  
Rear centre seat  
Two rear passenger seats, left and right side position,  
rows 2 and 3.  
One rear passenger seat, row 2 central position and row 3  
left side position. Integrated seat belt. Plastic shell trim.  
Folds to the low table position.  
Rear bench seat  
One three-seat bench seat, row 3.  
Seats  
Handling the side seat  
Access to row 3  
1. Place the head restraint in the low  
3. Fold the seat back onto the seat  
cushion and guide the tilting of the  
seat back forwards until the rear  
anchorages are unlocked. If you  
experience any difficulty, use the  
emergency control to unlock the  
anchorages.  
position.  
2. Push lever B upwards as far as  
possible.  
4. Place the seat in the vertical closed  
position.  
REAR SIDE SEATS  
Forwards/backwards adjustment  
Lift bar A and slide the seat forwards  
or backwards.  
Adjusting the angle of the seat back  
Push lever B upwards and adjust the  
angle as required.  
Release the lever to lock.  
Exit from row 3  
1. Place the head restraint in the low  
position.  
2. Pull control C.  
3. Guide the tilting of the seat back  
forwards until the rear anchorages  
are unlocked. If you experience any  
difficulty, use the red emergency  
control to unlock the anchorages.  
4. Place the seat in the vertical closed  
position.  
Following each entry or exit,  
reposition the raised seat guiding  
it until the rear anchorages lock in  
their rails.  
3
Seats  
Removing the side seat  
Control for sliding the rear side  
seats from row 3 or the boot  
Pull the strap (marked with the arrow  
symbol) to slide the seat in front of you.  
3. The strap, like the handle, enables  
you to remove the seat.  
1. Tilt the seat back forwards to  
detach the rear anchorages.  
2. Grab the red strap which appears  
and pull it upwards, the front  
anchorages unlock.  
Refitting the side seat  
1. Place the front anchorages at the  
front stop in the slides. Support the  
strap firmly for easier positioning of  
the seat.  
2. Tilt the folded seat towards the rear.  
The rear anchorages lock.  
Check that there is no obstacle  
obstructing the slides or  
preventing correct locking of the  
seat anchorages.  
3. Raise the seat back.  
4. Slide the seat.  
Seats  
"Low table" position  
1. Place the head restraint in the low  
3. You have a "low table". To return to  
the seat position, lift the handle and  
guide the raising of the seat back.  
position.  
2. At the top (at the back of the seat),  
lift the handle identified by the  
symbol and guide the tilting of the  
seat back towards its seat cushion.  
ROW 2 CENTRE SEAT  
This can be placed in row 3, on the left.  
3. Grab the red strap which appears  
and pull it upwards, the front  
anchorages unlock.  
4. The strap, like the handle, enables  
you to remove the seat.  
Removing the centre seat  
1. Place the seat in the "low table"  
position.  
2. Using the control which you pull, tilt  
the seat back forwards so releasing  
the rear anchorages from the  
slides.  
3
Seats  
Rear head restraints  
The rear head restraints can be  
removed and have two positions:  
-
-
high, position for use,  
low, storage position.  
To raise or lower a head restraint, pull  
it forwards sliding it at the same time.  
To remove it, place it in the high  
position, push the lug and pull it  
forwards and upwards.  
To refit it, engage the head restraint  
rods in the holes taking care to remain  
in the centreline of the seat back.  
Refitting the centre seat  
1. Place the front anchorages at the  
front stop in the slides. Support the  
strap firmly for easier positioning of  
the seat.  
2. Tilt the folded seat towards the rear.  
The rear anchorages lock.  
Check that there is no obstacle  
obstructing the slides or  
preventing correct locking of the  
seat anchorages.  
3. Raise the seat back and slide the  
seat.  
This turning operation must be  
carried out when stationary.  
Driving with a passenger seated  
facing the rear is prohibited.  
Never drive with the head  
restraints removed, they must be  
in place and correctly adjusted.  
When the vehicle is being driven,  
placing a row 2 seat in the closed  
position while a passenger is sitting  
in row 3 is prohibited.  
Turning a rear seat round  
The rear seats can be placed in a "face  
to face" position.  
Carry out the operations described for  
removal then turn the seat round and  
resume with the procedure for refitting  
the seat.  
Seats  
Seat back folded position  
1. Place the head restraints in the low 3. Tilt the seat back on the seat  
position.  
2. Pull the strap C upwards, from the  
tailgate.  
cushion.  
REAR BENCH SEAT  
Forwards/backwards  
adjustment  
From the seat cushion, lift bar A and  
slide the seat towards the front or the  
rear.  
Vertical position of the bench seat  
1. Place the head restraints in the low  
position.  
2. Pull the strap C upwards, from the  
tailgate.  
3. Fold the seat back onto the seat  
cushion.  
4. Pull the lever D to unlock the rear  
anchorages.  
5. Place the seat in the vertical  
"folded" position.  
From the boot, you can pull  
on strap B and slide the seat  
forwards to make it easier to load  
the vehicle.  
When driving, attach the retaining  
straps to the handles.  
The rear bench seat must only be  
fitted in row 3.  
3
Seats  
Removing the bench seat  
1. Fold the seat to the vertical  
3. The front anchorages unlock.  
position.  
2. Grasp the two bars E underneath  
the seat.  
For removal and refitting, pass the  
rear seat, in the "folded" position,  
through the sliding side doors.  
Good practice  
When the vehicle is being driven, it is  
prohibited for a passenger to sit:  
-
in row 3 if the seat back in front  
(row 2) is in the table position.  
-
in row 3 if the seat/bench in front  
(row 2) is in the vertical folded  
position.  
1. Position the front anchorages at the  
front stop of the runners.  
2. Tilt the folded seat rearwards.  
3. The rear anchorages then lock.  
4. Unlock the seat back and lift it  
using the strap C.  
Refitting the bench seat  
-
in the centre seat if the right-hand  
side seat is in the vertical folded  
position.  
Check that there is nothing  
blocking the runners which could  
prevent correct locking of the  
bench seat anchorages.  

Related Topics

EASE OF USE and COMFORT
Steering Wheel Controls / Lighting Windscreen Wipers Cruise Control Speed Limiter Ventilation / Air Conditioning Seats (Front) Modularity (Configurations) Practical Information (Layout/Storage) Courtesy Lights Sun Visor / Side Blinds Mirrors and Windows

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot