2002-2008 Cupra Born SUV Assistant systems User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Assistant systems for Your Cupra Born SUV First Generation (2002-2008)

Assistant systems  
could have a negative impact on the oper-  
ation of the assistants. If the vehicle is not  
properly repaired or structural modiꢁcations  
are made to it, the operation of the assistants  
may be aꢀected.  
Note  
Assistant systems  
●
Due to the system's detection limits in  
the surroundings, the systems may not give  
warnings or intervene on time, or they might  
do so even if it is not desired. In addition, the  
auxiliary systems may incorrectly interpret a  
manoeuvre and, as a result, warn the driver in  
an unexpected manner.  
General notes  
Safety advice  
WARNING  
●
The repair and adjustment of sensors and  
cameras requires special knowledge and  
tools. This is why CUPRA recommends visit-  
ing a specialised CUPRA dealer or any SEAT  
network dealer.  
●
Responsibility for driving rests with the  
driver at all times. The drive assist systems  
are not a replacement for driver attention.  
Focus all your attention on driving and be  
prepared to intervene at all times.  
Drive assist sensors and  
cameras  
System limits  
WARNING  
●
Use the drive assist systems only when con-  
Front radar  
ditions allow. The driving style must always  
be suitable for the weather, visibility, road  
and traꢀic conditions.  
●
Drive assist systems can not overcome the  
laws of physics. Depending on the circum-  
stances, a collision may not be avoidable.  
●
In order for drive assist systems to react  
●
Warnings, notices and indicator lamps may  
correctly, sensors and cameras must operate  
without limitations. Please read the notes on  
sensors and cameras in this chapter.  
not be displayed on time, or may be displayed  
incorrectly, e.g. if a vehicle approaches too  
quickly.  
●
Corrective interventions by drive assist sys-  
tems (e.g. interventions in the steering or  
brakes) may be insuꢀicient or may never oc-  
cur, depending on the circumstances. As a  
driver, you must be prepared to act at all  
times.  
Note  
●
Keep in mind the speciꢁc rules of each  
country, especially when it comes to driving,  
formation of an emergency corridor, braking  
distance, speed, parking position, wheel po-  
sition, etc. The driver is solely responsible  
for always complying with the speciꢁc regu-  
lations of each country.  
Fig. 118 On the front bumper: radar  
sensor.  
●
The area in front of and around the radar  
sensor should not be covered with adhesives,  
additional headlights or similar items, as this  
156  
Drive assistsensorsand cameras  
aged or adjusted incorrectly, switch oꢀ the  
Front Assist and ACC functions to avoid any  
damage. If this occurs have it adjusted.  
WARNING  
●
The visibility of the radar sensor can be  
impaired by dirt or environmental inꢂuen-  
ces such as rain, fog, snow, mud, dust, in-  
sects etc. In this case the Front Assist and  
ACC functions may stop working. The instru-  
ment panel displays the following message:  
No sensor vision!And the Front Assist  
unavailable or ACC unavailable warning lights  
come on.  
Front camera  
●
Clean the sensor area on the bumper as  
Fig. 119 Detection area.  
indicated in ››› page 315, Cleaning the  
exterior. When the radar sensor starts cor-  
rectly detecting again, the message disap-  
pears from the screen and the functions be-  
come available again.  
A radar sensor may be ꢀtted to the front  
bumper of the vehicle ››› Fig. 118. The front  
radar detects any objects in its detection zone  
››› Fig. 119 and provides support for the fol-  
lowing functions:  
Fig. 120 On the windscreen: ꢀeld of vision  
of the Lane Assist system camera.  
NOTICE  
●
Front Assist ››› page 170.  
●
If the radar sensor is dirty or poorly adjus-  
●
Adaptive Cruise Control (ACC) ››› page 163.  
ted, the Front Assist system may give unnec-  
essary warnings and apply the brakes inap-  
propriately.  
Depending on the equipment, the vehicle may  
be ꢀtted with a front camera on the front  
windscreen. This camera detects lane bounda-  
ries (lines) to provide support for the following  
functions:  
The radar can have a range of up to 160m  
(520ft) depending on road and weather condi-  
tions.  
●
The operation of the radar can be aꢀected  
by strong reꢂections of the emitted signal.  
This may occur, for example, in an enclosed  
car park or due to the presence of metallic  
objects (e.g. guard rails or sheets used in  
road works).  
●
Lane Assist ››› page 174.  
●
Travel Assist ››› page 177.  
●
Emergency assist ››› page 181.  
●
The sensor may not be adjusted correctly if  
it receives an impact. This may compromise  
the system's eꢀicacy or disconnect it. If you  
have the feeling that the radar sensor is dam-  
157  
Assistant systems  
ered. This may be the case if, for example,  
there is a layer of snow or ice over one of the  
sensors.  
NOTICE  
To avoid aꢀecting the operation of the sys-  
tems, take the following points into consider-  
ation:  
The relevant text message will appear in the  
instrument panel display.  
●
Clean the ꢁeld of vision of the camera reg-  
ularly and make sure it is free of snow and ice.  
Control lamps  
●
Do not cover the ꢁeld of vision of the cam-  
Side Assist (lane change assistance sys-  
tem) function not available  
era.  
●
Check that the windscreen is not damaged  
in the area of the camera's ꢁeld of vision.  
Rear cross traꢁic alert (RCTA) function  
not available.  
Fig. 122 Sensor detection zones.  
Door opening assistant (Exit Assist) not  
available.  
The radar sensors are located on the left and  
right of the bumper and are not visible from  
the outside ››› Fig. 121. The sensors monitor  
both the blind spot and traꢁic behind the vehi-  
cle ››› Fig. 122.  
Rear radar  
NOTICE  
●
The radar sensors on the rear bumper may  
They support the following functions:  
be damaged or shifted in the event of a colli-  
sion, for example, when entering or exiting a  
parking space. This may result in the system  
disconnecting itself, or at least possibly hav-  
ing its functionality diminished.  
●
Lane departure warning (Side Assist)  
››› page 183.  
●
Rear cross traꢁic alert (RCTA) ››› page 209.  
Door opening warning (Exit Assist)  
●
●
In order to ensure that the radar sensors  
››› page 210.  
work properly, keep the rear bumper free of  
snow and ice and do not cover it.  
Fig. 121 Rear view of the vehicle: radar  
sensor areas.  
Automatic deactivation of supported func-  
tions  
●
The rear bumper should only be painted  
with paint authorised by CUPRA. The lane  
departure warning's functions may be limited  
or work incorrectly if other paints are used.  
The rear radar sensors deactivate automati-  
cally when, among other reasons, one of the  
sensors is detected to be permanently cov-  
●
The visibility of radar sensors may be aꢀec-  
ted due to leaves, snow, strong haze or dirt,  
among others. Clean the area in front of the  
sensors.  
158  
Speedlimiter
●
●
Top View Camera ››› page 206.  
Rear View Camera ››› page 204.  
●
Never use auto lane changing or the rear  
Note  
cross traꢀic alert if the radar sensors are  
dirty.  
●
In order to guarantee good operation, keep  
the sensors clean, free of snow and ice, and  
do not cover them with stickers or other ob-  
jects.  
●
Radar operation may also be aꢀected if ob-  
WARNING  
jects such as bicycle racks or luggage racks  
interfere with the visibility of the radars.  
Fitting a number plate frame may interfere  
with the view shown on the screen, as it may  
reduce the camera’s ꢁeld of vision.  
●
If you use high-pressure or vapour equip-  
ment for cleaning, do not apply it directly,  
unless you do so very brieꢂy, and always keep  
a distance of more than 10 cm away.  
Ultrasound sensors  
The bumpers are ꢀtted with ultrasound sen-  
sors to perform the following functions:  
●
Fitting certain accessories to the front of  
NOTICE  
the vehicle, such as a plate holder with ad-  
vertising, may interfere with the operation of  
the Park Assist.  
●
In order to guarantee good system opera-  
tion, keep the cameras clean, free of snow or  
ice, and do not cover them with stickers or  
other objects. The camera can be cleaned by  
operating the wiper.  
●
Automatic parking system ››› page 194  
●
Park assist plus ››› page 191.  
Area View system  
●
Never use abrasive cleaning products to  
clean the camera lens.  
NOTICE  
●
Damage to the radiator grille, bumper,  
●
Do not use hot or warm water to remove ice  
wheel arch and vehicle underbody can mod-  
ify the orientation of the sensors. This can af-  
fect the parking aid function. Have the func-  
tion checked by a specialised workshop.  
or snow from the camera lens. Doing so could  
damage the camera.  
●
A number plate or number plate holder  
Speed limiter  
with dimensions that exceed the space for  
the number plate, or a cured or deformed  
number plate can cause false detections or a  
loss of visibility for the sensors.  
Introduction  
The speed limited helps the driver not to ex-  
ceed a set speed.  
Fig. 123 On the rear bumper: location of  
the rear assist camera.  
Speed range  
Depending on your vehicle’s equipment, it can  
be ꢀtted with 1 or 4 cameras that provide sup-  
port to the following functions:  
The speed limiter helps avoid exceeding a pro-  
grammed speed, from 30 km/h (20 mph) ap-  
prox. and faster.  
159  
Assistant systems  
By selecting the speed limiter  
Adjusting the speed  
●
Using the speed limiter under adverse  
weather conditions is dangerous and can  
cause serious accidents, e.g. aquaplaning,  
snow, ice, leaves, etc. Only use the speed  
limiter when the status of the road and the  
weather conditions allow it.  
The speed limitation can be interrupted at any  
time by depressing the accelerator pedal fully,  
beyond the point of resistance. As soon as the  
saved speed is exceeded, the green indicator  
light ꢂashes and an audible warning signal may  
sound. The speed is stored.  
The programmed speed can be set:  
+ 1 km/h (1 mph)  
- 1 km/h (1 mph)  
+ 10 km/h (5 mph)  
- 10 km/h (5 mph)  
The limiter is reactivated automatically after re-  
turning to less than the set speed.  
Operating the speed limiter  
Interrupting the adjustment  
Status display  
●
Press the button.  
When the speed limiter is switched on, the  
instrument cluster display shows the saved  
speed and the system status:  
The speed is stored.  
Reinstating the cruise control  
●
Press the  
button.  
It lights up grey  
The limiter will re-activate as soon as the vehi-  
cle is moving at a speed lower than the saved  
one.  
The speed limiter is switched on but reg-  
ulation is not active.  
Fig. 124 On the multifunction steering  
wheel: buttons to control the speed limiter.  
Lights up green  
The speed limiter is switched on and ac-  
tive.  
Switching oꢀ  
●
Press and hold the button  
.
Connecting  
The speed limiter switches oꢁ and the speed is  
deleted.  
●
Press the button.  
WARNING  
It does not take eꢁect yet.  
After use, always switch oꢀ the speed limiter  
to prevent the speed being regulated against  
your wishes.  
Switch to another driver assistance system  
Start regulation  
Depending on the equipment, you can switch  
to the following driver assistance systems:  
●
The speed limiter does not relieve the  
●
While driving, press the button  
.
driver of their responsibility to drive at the  
appropriate speed. Do not drive at high  
speed if not necessary.  
The current speed is saved as a limit speed.  
●
●
Adaptive Cruise Control (ACC)  
Speed limiter.  
160  
Speed limiter withproactivespeed adjustment  
1. Press the button  
button.  
or swipe across the  
●
Always adapt your speed to suit visibility,  
Speed limiter with proac-  
tive speed adjustment  
weather, road and traꢀic conditions.  
2. To select the desired system, swipe your  
ꢀnger left or right.  
●
Always pay attention to traꢀic and always  
keep the vehicle environment in mind.  
Introduction  
●
3. Press the  
button.  
Always be prepared to adjust the speed  
yourself. If the traꢀic sign recognition system  
is not working properly or the navigation data  
is not updated, the speed may change unex-  
pectedly and suddenly or may not be suitable  
for the current traꢀic situation. In addition,  
the speed adjusted by the system may not  
suit your driving style.  
The speed limiter is switched oꢁ.  
The speed limiter with proactive speed adjust-  
ment automatically adapts a maximum speed  
that you have saved to the detected speed lim-  
its.  
Troubleshooting  
The speed limiter is not available  
The speed limiter with proactive speed adjust-  
ment is an additional function of the speed  
limiter and uses the infotainment system’s dy-  
namic road sign display ››› page 27 and navi-  
gation data.  
●
Always be prepared to adjust the speed  
The control lamp switches on yellow.  
yourself. If you drive without any active gui-  
ded route, if you leave the route calculated  
by the navigation system or if the position of  
the vehicle cannot be determined correctly  
because the GPS does not provide accurate  
data, the speed may change unexpectedly  
and suddenly or may not adapt to the current  
traꢀic situation.  
●
Malfunctions Switch oꢁ the speed limiter and  
go to a specialist workshop.  
The speed limiter with proactive speed adjust-  
ment is available depending on the equipment,  
but not in all countries.  
The adjustment is interrupted unexpectedly  
●
You have switched oꢁ the Electronic Stabili-  
zation Control (ESC).  
WARNING  
●
The brakes have overheated. Wait for the  
●
●
Always use up to date navigation data.  
Always take into account the maximum  
The smart technology of the speed limiter  
with proactive speed adjustment cannot  
overcome the limits imposed by the laws of  
physics and only works within the limits of  
the system. Never allow the greater conven-  
ience oꢀered by this function to induce you  
to take any risk that compromises safety. Se-  
rious accidents and injuries can occur if the  
speed limiter with proactive speed adjust-  
ment is used carelessly or unintentionally.  
The system is not a replacement for driver  
awareness.  
brakes to cool down and check the operation  
again.  
permitted speed. In the case of speed limita-  
tions that are not included in the navigation  
data, the maximum permitted speed may be  
exceeded.  
●
If the fault continues, consult a specialised  
workshop.  
For safety reasons, the speed limiter only  
switches oꢁ fully whenever the driver stops  
pressing the accelerator pedal or switches the  
system oꢁ manually.  
Note  
Please also note the information of relevance  
to safety on the speed limiter ››› page 159.  
161  
Assistant systems  
+10 km/h (5 mph) Firmly press the + button  
or swipe your ꢀnger from bottom to top  
over the button. The ꢀrst time it is op-  
erated, the speed increases in steps of  
10 (km/h) or 5 (mph).  
Limitations of proactive speed ad-  
justment  
Driving with proactive speed ad-  
justment  
●
In addition to the limitations of the dynamic  
road sign display system ››› page 27, the  
speed limiter with proactive speed adjustment  
has the following limitations inherent to the  
system:  
Switch on the speed limiter and start the  
control ››› page 159.  
-10 km/h (5 mph) Press the – button ꢀrmly  
or swipe your ꢀnger over the button from  
top to bottom. The ꢀrst time it is operated,  
the speed is reduced in steps of 10 (km/h)  
or 5 (mph).  
●
Activate the proactive speed adjustment.  
As soon as the system recognises a  
speed restriction en route, a warning  
is displayed on the instrument cluster  
screen. The detected speed is saved as the  
new desired speed.  
●
The speed limiter with proactive speed ad-  
justment only recognises traꢁic signs showing  
a speed limit.  
If you adjust the indicated speed excessively,  
the proactive speed adjustment is interrupted.  
●
Traꢁic signs that indirectly show a speed re-  
striction, e.g. signs at the entrance to towns,  
are only recognised on the basis of navigation  
data.  
Interrupting speed adjustment  
Note  
●
Press the button  
on the multifunction  
steering wheel or release and press the accel-  
erator pedal twice. The last saved speed is re-  
sumed.  
●
When a speed restriction is recognised, the  
●
If a warning is given of a speed restriction  
proactive speed adjustment also adapts the  
saved speed, even if the speed limiter is not  
active.  
based on navigation data, without it being de-  
tected by the dynamic road sign display, the  
indicated speed will be adjusted to the most  
recently saved speed.  
●
Press the  
button on the multifunction  
●
If the speed of travel considerably exceeds  
steering wheel. The current speed is taken.  
the speed limit detected by the traꢀic signal  
detection system, a relevant warning is dis-  
played in the instrument panel display.  
●
Press the button on the multifunction  
●
The speed limiter with proactive speed ad-  
steering wheel. The system switches to a pas-  
sive state.  
justment is not available for speed restrictions  
lower than approx. 30 km/h (approx. 20 mph)  
that are detected. In this case, a relevant  
message is displayed on the instrument panel  
screen.  
●
When merging onto a motorway or dual  
carriageway, the recommended speed is au-  
tomatically saved as the desired speed.  
Adjust the displayed speed using the buttons  
on the multifunction steering wheel  
+1 km/h (1 mph) Gently press the + button.  
-1 km/h (1 mph) Gently press the – button.  
Activate proactive speed adjust-  
ment  
The speed limiter with proactive speed adjust-  
ment can be activated in the infotainment sys-  
tem’s assistants menu.  
162  
ACC - AdaptiveCruiseControl  
Speed range  
Troubleshooting  
WARNING  
You can set a speed between 20 km/h (15  
mph) and the maximum speed of the vehicle.  
The ACC’s technology cannot overcome the  
system's inherent limitations or change the  
laws of physics. If used negligently or invol-  
untarily, it may cause serious accidents and  
injuries. The system is not a replacement for  
driver awareness.  
A message is displayed indicating that pro-  
active speed adjustment is not currently  
available or not oꢀered in your country.  
The ACC can bring the vehicle to a standstill if  
a vehicle in front stops.  
●
If this message is displayed for a longer pe-  
riod of time and proactive speed adjustment  
is available in your country, please contact a  
specialist workshop.  
Driving with ACC  
●
●
Always be prepared to brake or accelerate.  
If you press the accelerator pedal the ACC  
You can override the ACC at any time. Brak-  
ing interrupts the ACC. If you accelerate, reg-  
ulation is interrupted during acceleration and  
then resumed.  
will stop working. Therefore, it will not brake  
or request any braking intervention.  
Note  
●
Adapt your speed and safe distance to the  
Depending on the anomaly in question, addi-  
tional information may be displayed in Vehi-  
vehicle in front of you at all times to suit visi-  
bility, weather, road and traꢀic conditions.  
Driver intervention prompt  
cle status ››› page 34.  
ACC is subject to certain limitations in-  
herent to the system. This means that the  
driver will have to control the speed and  
distance from other vehicles in certain sit-  
uations. In this case, the instrument clus-  
ter display will tell you to intervene by  
applying the brake, and an audio warning  
will be played.  
●
Do not use the ACC in poor visibility, or on  
roads that are steep, with lots of curves or  
slippery.  
ACC - Adaptive Cruise  
Control  
●
Never use ACC when driving oꢀ-road or on  
unpaved roads.  
●
The system may not react in time to  
stationary obstacles (such as a traꢀic jam  
queue), particularly at high speeds. React  
soon enough to avoid a hazardous situation.  
Introduction  
Adaptive Cruise Control (ACC) maintains a  
constant speed set by the driver. When ap-  
proaching another vehicle in front, the ACC  
detects it and adapts the speed automatically,  
maintaining a distance set by the driver.  
Radar sensors  
●
The system may not react to stopped vehi-  
The ACC uses the front radar technology. Read  
its maintenance instructions and information  
about its limitations ››› page 156.  
cles in the same lane. You must react early  
enough yourself in this case.  
●
The system does not react to people, an-  
imals or vehicles that are crossing or ap-  
proaching in the opposite direction.  
Does my vehicle have ACC?  
●
If you are driving with a spare wheel ꢁtted,  
Your vehicle has ACC if it has a conꢀguration  
menu in the infotainment system.  
the ACC system could automatically switch  
oꢀ. Switch oꢀ the system when starting oꢀ.  
163  
Assistant systems  
ACC operation  
Connecting  
●
Brake immediately if the ACC does not slow  
down enough.  
●
Press the button on the multifunction  
●
Brake immediately when a driver interven-  
steering wheel ››› Fig. 126.  
The ACC does not regulate anything yet  
(standby).  
tion instruction is displayed on the instru-  
ment cluster screen.  
●
If the vehicle continues to move involun-  
tarily after a driver intervention prompt,  
brake the vehicle.  
Start regulation  
Activating the ACC system also automatically  
activates the ESC and traction control (TCS).  
●
The brake pedal may move downwards dur-  
ing braking. Be careful not to position your  
foot under the pedal.  
●
To start regulation, press the button  
››› Fig. 126.  
Fig. 125 On the instrument panel display:  
ACC active.  
Note  
The ACC saves the current speed and main-  
tains the set distance. If the current speed is  
outside the preset speed range, ACC sets the  
minimum speed (if driving slowly) or maximum  
speed (if driving fast).  
If the ACC does not work as described in  
this chapter, do not use it until it has been  
checked by a specialised workshop. CUPRA  
recommends visiting a specialised CUPRA  
dealer or any SEAT dealership.  
Depending on the driving situation, the follow-  
ing indicator lamps come on:  
Lights up green  
ACC connected, no vehicle detected in  
front.  
Lights up green  
ACC connected, vehicle detected in  
front.  
Fig. 126 On the multifunction steering  
wheel: buttons for operating the ACC.  
When the ACC is in standby, the indicator  
lamps light up grey.  
››› Fig. 125  
1
Vehicle ahead detected. It will light up if  
the distance to the vehicle is adjusted.  
2
Selected distance level 2.  
164  
ACC - AdaptiveCruiseControl  
Reinstating the cruise control  
Setting speed  
WARNING  
●
To program the speed, press the or  
››› Fig. 126 buttons to the desired speed. The  
speed is adjusted at intervals of 10 km/h (5  
mph).  
Press the  
button. The ACC regulates to  
Before driving oꢀ, check that the road is  
clear. The radar sensor may not detect ob-  
stacles on the road. This could cause an acci-  
dent and serious injuries. If necessary, apply  
the brake.  
the last speed and distance setting.  
●
OR: Press the button  
to regulate to the  
current speed.  
While the ACC is active, you can press the  
Switching oꢀ  
button to increase the desired speed by 1 km/h  
(1 mph). You can then press  
by 1 km/h (1 mph).  
to decrease it  
NOTICE  
●
Press and hold the button . The set speed  
is cleared.  
If you increase speed using the accelerator  
pedal, the ACC may not be able to safely  
adjust the speed of the distance due to the  
limitations of the system.  
Setting your distance level  
Exceeding the speed regulated by the ACC  
The distance can be set to one of ꢀve levels,  
from very short to very long:  
While driving with the ACC switched on, the  
driver can increase speed by pressing the ac-  
celerator pedal. ACC regulation is suspended  
●
Be prepared to react if required by the sit-  
uation.  
●
Press the button and then the button or  
››› Fig. 126.  
until you release the accelerator pedal ›››  
.
●
Alternatively, press the button as many  
Special driving situations  
Set the default distance setting  
times as necessary to set the desired distance.  
In the Infotainment system, you can pre-select  
the distance level when connecting the ACC  
from:  
Keep in mind each country’s regulations on  
minimum braking distances.  
Suspend regulation (standby)  
●
Very short, Short, Medium, Long and Very  
long using the Infotainment system:  
Driver assistants > Smart Assistants > ACC  
››› page 35.  
>
●
Brieꢂy press the button ››› Fig. 126 or  
press the brake pedal.  
The ACC indicator lamp is grey; the speed and  
distance are saved.  
Changing the driving proꢁle  
If the ESC or TCS is switched oꢁ, the ACC is  
automatically interrupted.  
The driving proꢀle selected can aꢁect  
ACC acceleration and braking behaviour  
››› page 149.  
Fig. 127 On the instrument panel display:  
ACC active, vehicle detected on the left.  
165  
Assistant systems  
Be aware of the limitations and warnings  
described at the beginning of this chapter  
››› page 163, Introduction.  
The ACC remains active and the message ACC  
ready to startis displayed on the instru-  
ment cluster for a few seconds. You can extend  
or reactivate this warning by pressing the but-  
●
Always check the road before moving oꢀ,  
and apply the vehicle brakes yourself if nec-  
essary.  
ton  
or by grabbing the wheel if your vehicle  
Avoid undertaking on the right1)  
is ꢀtted with Travel Assist. During this time, the  
vehicle will move oꢁ again if the vehicle in front  
moves forwards.  
ACC system limitations  
If a vehicle is detected in the left lane that is  
travelling at a speed slower than that set by  
the driver, it will brake the vehicle within the  
comfort limits of the system to avoid passing it  
To move oꢁ when the message ACC ready  
to startis not longer displayed, once the  
vehicle in front has moved oꢁ:  
on the right ››› Fig. 127.  
You can cancel this regulation by changing the  
set speed or by pressing the accelerator pedal.  
●
●
Press the accelerator pedal.  
OR: press the button on the multifunc-  
The function works at speeds over 80 km/h  
(50 mph). It may not be available in certain  
countries.  
tion steering wheel.  
The ACC does not remain active in the follow-  
ing cases:  
●
●
●
The stopping phase lasts for several minutes.  
When a vehicle door is opened.  
Overtaking  
When the turn signal is switched on for over-  
taking, the ACC reduces the distance from the  
vehicle in front to help with the overtaking ma-  
noeuvre. The set cruising speed will not be ex-  
ceeded.  
If the ignition is switched oꢁ.  
Fig. 128  
Vehicle on a bend.  
WARNING  
Motorcyclist ahead, out of range of the  
radar sensor.  
If the message ACC ready to startis  
displayed on the instrument cluster display  
and the vehicle in front moves oꢀ, your vehi-  
cle will move oꢀ automatically. In this case,  
any obstacles in the road may not be detec-  
ted. This may cause serious accidents and in-  
juries.  
The function works at speeds over 80 km/h  
(50 mph). It may not be available in certain  
countries.  
Stop&Go function  
The ACC can bring the vehicle to a standstill if  
the vehicle in front stops.  
1)  
Or on the left, in countries that drive on the left hand side of the road.  
166  
ACC - AdaptiveCruiseControl  
●
●
On roads with embedded metal objects such  
Vehicles travelling in the opposite direction  
as train or tram tracks.  
or crossing the road.  
●
●
On roads with loose gravel.  
Other stationary obstacles  
Pay special attention when using ACC in the  
following situations:  
The ACC may not react to stationary vehicles.  
If, for example, a vehicle detected by the ACC  
turns or moves over and there is a stationary  
vehicle in front of it, the ACC will not react to  
On curves  
the second vehicle ››› Fig. 129  
.
The ACC may not detect the vehicle in front  
on a curve, or may regulate the distance from  
WARNING  
vehicles in other lanes ››› Fig. 128  
.
Using the ACC in the above situations can  
cause serious accidents and injuries, and you  
could break the law.  
Vehicles outside the sensor zone  
In the following situations the ACC may not  
react, or may react slowly or inappropriately:  
Fig. 129  
Vehicle changing lanes. One  
●
Vehicles that are not aligned while driving or  
Troubleshooting  
vehicle turning and another stationary.  
that are outside the sensor's detection area,  
ACC not available  
such as motorcycles ››› Fig. 128  
.
The limits of the ACC system mean that it is not  
●
Vehicles that move into your lane, a short  
appropriate in all situations ›››  
in Introduc-  
distance from your vehicle ››› Fig. 129  
.
The indicator lamp lights up yellow:  
tion on page 163.  
●
Vehicles with loads or accessories that pro-  
●
The radar sensor is dirty or adjusted in-  
CUPRA does not recommend using the func-  
tion in the following cases ›››  
trude from the sides, rear or roof.  
correctly. Take into account the warnings  
described at the beginning of this chapter  
››› page 156  
There is a fault or a defect. Turn oꢁ the vehi-  
cle's ignition and turn it on again after a few  
minutes.  
:
●
●
●
●
Heavy rain, snow or fog.  
Objects that are not detected  
When going through tunnels.  
In sections with roadworks.  
●
The ACC function only detects and reacts to  
vehicles moving in the same direction. There-  
fore it does not detect:  
On routes with curves, e.g. on mountain  
roads.  
●
If the problem persists, consult a specialised  
●
●
People  
●
●
workshop.  
On oꢁ-road routes.  
In covered car parks.  
Animals  
167  
Assistant systems  
The ACC does not work as expected  
WARNING  
Predictive speed adjust-  
ment  
●
Make sure that the conditions are met for the  
The predictive speed adjustment smart tech-  
nology cannot overcome the limits imposed  
by the laws of physics and it only works within  
the limits of the system. Never allow the en-  
hanced convenience of this function induce  
you to take any risk that compromises safety.  
If used negligently or involuntarily, it may  
cause serious accidents and injuries. The sys-  
tem is not a replacement for driver aware-  
ness.  
radar sensor to operate properly ››› page 156.  
●
If the brakes overheat, regulation stops au-  
Introduction  
tomatically. Wait for them to cool down and  
check the operation again.  
The predictive speed adjustment adapts the  
speed to the speed limitations detected and  
to the road layout (curves, crossings, round-  
abouts, etc.).  
●
Unusual noises during automatic ACC brak-  
ing are normal and do not indicate any anoma-  
lies.  
Predictive speed adjustment is an additional  
function of the ACC ››› page 163 and uses the  
traꢁic signal detection system ››› page 27 and  
the navigation data of the infotainment system.  
The following conditions may lead the ACC  
not to react:  
●
Always adapt your speed to suit visibility,  
weather, road and traꢀic conditions.  
●
Always pay attention to traꢀic and always  
keep the vehicle environment in mind.  
●
●
●
●
●
●
●
●
The accelerator or brake is depressed.  
No gear is engaged or the vehicle is in gear R.  
The vehicle is reversing.  
Predictive speed adjustment is available de-  
pending on the equipment, although not in all  
countries.  
●
Always be prepared to adjust the speed  
yourself. If the traꢀic sign recognition system  
is not working properly or the navigation data  
is not updated, the speed may change unex-  
pectedly and suddenly or may not be suitable  
for the current traꢀic situation. In addition,  
the speed adjusted by the system may not  
suit your driving style.  
ESC is operating.  
The driver is not wearing his/her seat belt.  
A vehicle brake light is faulty.  
Reaction at the end of a traꢀic jam  
Vehicles with Car2X technology (depending on  
the equipment and not in all countries) can  
interact with other vehicles in their vicinity.  
This allows your vehicle to receive information  
about the presence of a traꢁic jam ahead and  
to reduce speed in time.  
The parking brake is applied.  
Driving on an excessive slope.  
●
Always be prepared to adjust the speed  
yourself. If you drive without any active gui-  
ded route, if you leave the route calculated  
by the navigation system or if the position of  
the vehicle cannot be determined correctly  
because the GPS does not provide accurate  
data, the speed may change unexpectedly  
and suddenly or may not adapt to the current  
traꢀic situation.  
Requirements:  
●
●
Car2X activated in the infotainment system.  
The option to react at the end of traꢁic  
jams is activated in the infotainment system  
››› page 169.  
●
Always use up to date navigation data.  
168  
Predictivespeedadjustment  
●
If a speed limitation is notiꢀed based on the  
panel display. This warning will indicate the  
reason and the speed to which the vehicle will  
adjust due to said limitation.  
●
Always take into account the maximum  
navigation data without it being detected by  
the traꢁic signal detection system, the indica-  
ted speed will be adjusted to the speed that  
was saved the last time.  
permitted speed. In the case of speed limita-  
tions that are not included in the navigation  
data, the maximum permitted speed may be  
exceeded.  
Adjustment due to a speed limitation.  
Regulation due to a speed limit.  
Regulation due to a roundabout.  
Regulation due to a junction.  
●
Predictive speed adjustment is not available  
for speed limitations below approx. 20 km/h  
(approx. 15 mph). In this case, a relevant mes-  
sage is displayed on the instrument panel  
screen.  
Note  
Also note the information related to the ACC  
relevant to safety ››› page 163.  
Adjustment due to a road layout.  
Regulation due to a traꢁic jam.  
Activating the predictive speed ad-  
justment  
Limitations of the predictive speed  
adjustment  
In the event of adjustment due to a speed  
limitation, the detected speed will be saved as  
the new desired speed. In the event of adjust-  
ment due to the road layout, the vehicle will  
accelerate again after leaving the reason for  
the adjustment behind and the speed will be  
adjustment to that which has been saved.  
In the infotainment system, in the assist serv-  
ices menu, you can individually adjust the  
type of incident the vehicle should react to  
››› page 35:  
In addition to the limitations of the road sign  
detection system ››› page 27 and the limita-  
tions of the ACC, predictive speed adjustment  
has the following limitations inherent to the  
system:  
●
●
●
Response to road layout.  
Response at permitted speeds.  
Reaction to a traꢁic jam.  
The speeds indicated for curves depend on  
●
Predictive speed adjustment only recognises  
the driving proꢀle››› page 149.  
traꢁic signals that show a speed limitation. The  
predictive speed adjustment does not take into  
account, above all, the rules on priority of pas-  
sage or traꢁic lights.  
Interrupting speed adjustment  
Driving with the predictive speed  
adjustment  
●
●
During the warning, press the button  
During the regulation, press the button  
.
●
Traꢁic signs that indirectly show a speed re-  
.
striction, e.g. signs at the entrance to towns,  
are only recognised on the basis of navigation  
data.  
●
Connect the ACC ››› page 164.  
Set the distance and speed.  
Adjust the announced speed  
●
●
The announced speed can only be adjusted in  
the event of adjustment due to a speed limita-  
tion.  
●
On roads that are not included in the naviga-  
Activate the predictive speed adjustment.  
tion data, or that are included with little accu-  
racy, predictive speed adjustment is not availa-  
ble.  
As soon as the system recognises a speed lim-  
itation or a relevant road layout during the  
route, a warning will appear on the instrument  
169  
Assistant systems  
Troubleshooting  
●
●
Parked vehicles.  
Multifunction steering wheel:  
Vehicles, pedestrians and cyclists that are  
+ 1 km/h (1 mph), only while the ACC is  
adjusting  
A message is displayed indicating that pre-  
dictive speed adjustment is not currently  
available or not in your country.  
travelling in the same lane and direction.  
●
Pedestrians and cyclists who transversely  
- 1 km/h (1 mph), only while the ACC is  
adjusting  
cross the vehicle path.  
●
If this message is displayed for a long time  
The Front Assist records the mentioned ob-  
jects by means of a camera on the top of the  
windscreen and a radar sensor on the front of  
the vehicle ››› page 156.  
Depending on several factors and how critical  
the situation is, the system operates in a stag-  
gered manner.  
+ 10 km/h (5 mph)  
and predictive speed adjustment is available in  
your country, contact a specialised workshop.  
- 10 km/h (5 mph)  
Note  
If you adjust the indicated speed excessively,  
the predictive speed adjustment is interrupted.  
Depending on the anomaly in question, addi-  
tional information may be displayed in Vehi-  
cle status››› page 34.  
First informing the driver, and if there is no or  
insuꢁicient reaction, then activating an auton-  
omous emergency braking or an evasive ma-  
noeuvre as indicated by the conditions that will  
be discussed in the following points.  
Note  
●
When a speed limitation is recognised, the  
emergency brake assis-  
tance system (Front As-  
sist)  
predictive speed adjustment also adapts the  
saved speed even if the ACC is switched oꢀ.  
However, it will not adjust.  
The system can be cancelled if the accelerator  
pedal is pressed or the steering wheel is turned  
ꢀrmly.  
●
If the speed of travel considerably exceeds  
the speed limit detected by the traꢀic signal  
detection system, a relevant warning is dis-  
played in the instrument panel display.  
Depending on the equipment and the coun-  
try, the Front Assist also includes the following  
functions:  
Introduction  
●
In the event of joining a highway without  
The objective of the system is to prevent head-  
on collisions against objects that may be in the  
vehicle’s path or minimise the consequences  
of such impacts.  
speed limitation, the recommended speed is  
automatically saved as the desired speed. If a  
higher speed has previously been saved for a  
motorway without a speed limit, this is used  
instead of the recommended speed.  
●
Pedestrian protection ››› page 172  
●
Cyclist protection ››› page 172  
The function is designed to avoid collisions  
against:  
●
Dodge assist ››› page 172  
●
Turn assist ››› page 172  
170  
emergency brakeassistancesystem (Front Assist)  
Safety distance warning  
Automatic braking  
WARNING  
If the system detects that you are driving too  
close to the vehicle in front, it will warn the  
driver with this indication on the instrument  
If the driver also fails to react to the critical  
warning, the system may initiate independent  
emergency braking by progressively increasing  
the braking in accordance with the criticality of  
the situation.  
●
Front Assist is a driving assistance function  
that can never replace the driver’s attention.  
●
Front Assist cannot change the laws of  
panel display  
.
physics or replace the driver in terms of  
keeping control of the vehicle and reacting  
to a possible emergency situation.  
The timing of the warning varies depending  
on driver behaviour, vehicle speed and relative  
speed between both.  
Driver emergency braking assistance system  
●
Following a Front Assist emergency warn-  
ing, pay immediate attention to the situation  
and try to avoid the collision where appropri-  
ate.  
If the driver, after the critical warning, starts  
braking but the system detects that the brake  
is not being applied with suꢁicient force, the  
braking intensity will be increased. This brake  
assist only occurs if the pedal is pressed ꢀrmly.  
The safety distance warning is active from ap-  
prox. 65 km/h (40 mph).  
Advance warning  
Warning levels and brake assist  
If the system detects a possible collision with  
the vehicle in front, it alerts the driver by  
means of an audible warning and an indi-  
cation on the instrument panel display  
WARNING  
●
The system cannot prevent a collision, al-  
though it can signiꢁcantly minimise the con-  
sequences by reducing the speed and the  
force of the impact.  
››› Fig. 130.  
The warning moment varies depending on the  
traꢁic situation and driver behaviour. At the  
same time, the vehicle will prepare for a possi-  
●
When the Front Assist causes a braking, the  
brake pedal is “harder”.  
ble emergency braking ›››  
in Introduction  
●
Automatic interventions by the Front Assist  
on page 171.  
on the brakes may be interrupted by press-  
ing the accelerator or moving the steering  
wheel.  
Fig. 130 On the instrument panel display:  
advance warning indications.  
When Front Assist is connected, the indica-  
tions of other functions on the screen may be  
hidden.  
●
The Front Assist may brake the vehicle until  
Front Assist is active from 5 km/h (3 mph).  
Depending on diꢁerent conditions (vehicle  
speed, speed and type of object recognised,  
etc.), some of the stages described below are  
omitted to optimise the performance of the  
system.  
it stops completely. However, the brake sys-  
tem does not halt the vehicle permanently.  
Use the foot brake!  
Critical warning  
If the driver fails to react to the advance warn-  
ing, the system may actively intervene in the  
brakes and generate a brief jolt to warn the  
driver of the imminent danger of a collision.  
171  
Assistant systems  
The system is active between approximately  
30 km/h (20 mph) and 150 km/h (90 mph).  
Pedestrian and cyclist recognition  
System limitations  
The system recognises pedestrians and cyclists  
who travel in the same lane and direction and  
pedestrians and cyclists who transversely cross  
the vehicle's path.  
Limitations  
This system does not react to objects that  
cross transversely or to animals. The basic limi-  
tations of Front Assist should also be taken into  
account ››› page 172.  
Pedestrian and cyclist recognition technology  
cannot exceed the physically prescribed limits  
and works exclusively within the system’s limits.  
The responsibility for braking always depends  
on the driver.  
Turn assist  
Fig. 131 On the instrument cluster  
screen: indication of the system’s initial  
self-calibration.  
The pedestrian and cyclist recognition can  
cause undesired warnings and braking inter-  
ventions, e.g. with a hidden radar sensor or a  
dirty camera ꢀeld of vision.  
Turn assist can avoid a collision with a vehicle  
approaching in the opposite direction, by brak-  
ing the vehicle itself when the intention is to  
turn.  
Front Assist has certain limitations inherent to  
the system. Thus, in certain circumstances,  
some of the reactions may be inappropriate  
from the driver's standpoint. So pay attention  
in order to intervene if necessary.  
Be ready to take charge of the vehicle at any  
time.  
This system is active up to 15 km/h (9 mph).  
The pedestrian and cyclist recognition operat-  
ing speed range is lower than that of the Front  
Assist.  
Limitations  
The turn-oꢁ assist function is available if you  
have indicated your intention to turn by acti-  
vating the turn signal, you have turned the  
steering wheel and the turning path has star-  
ted.  
The following conditions may cause the  
Front Assist not to react or to do so too late:  
Dodge assist  
●
In the ꢀrst few instants of driving after switch-  
Dodge assist helps the driver avoid an obstacle  
in critical conditions.  
ing on the ignition, due to the system’s initial  
auto-calibration. Notiꢀcation of this phase will  
be given by the following indication on the in-  
It only reacts to vehicles that are in the path of  
the vehicle (not to animals, people, etc.).  
Once the Front Assist has activated a critical  
warning, if the driver intends on dodging the  
object, the dodge assist will help correct the  
trajectory. The driver must start and ꢀnish the  
manoeuvre, as this is an assistance system and  
not an autonomous one.  
The basic limitations of the Front Assist must  
also be taken into account››› page 172.  
strument cluster screen  
.
172  
emergency brakeassistancesystem (Front Assist)  
●
If several brake lights of the vehicle or electri-  
for a short period of time while the system  
starts. During this phase, the instrument clus-  
ter screen will display the following indication  
››› Fig. 131.  
When the Front Assist is disabled, so too are  
the advance warning and the distance warn-  
ing functions. CUPRA recommends leaving the  
Front Assist activated except in the situations  
presented in ››› page 174.  
Unrecognised objects  
cally connected trailer are damaged.  
●
Vehicles travelling outside the reach of the  
●
●
●
●
●
If the vehicle is reversing.  
sensors at close range from your own vehicle.  
In case of snow or heavy rain.  
●
Vehicles that suddenly change to the lane on  
which your vehicle is travelling.  
In case of dazzling sun or total darkness.  
Entrances and exits of tunnels.  
●
Pedestrians that cannot be recognised be-  
cause they are partially or totally hidden.  
In complex driving situations (such as traꢁic  
●
Objects such as walls, posts, fences, trees or  
islands, cut-through roundabouts, etc), Front  
Assist may issue warnings and intervene in  
braking in an unnecessary manner.  
garage doors.  
●
Loads and accessories of other vehicles that  
Switching the Front Assist on and oꢀ  
protrude over the sides, backwards or over the  
top.  
For more details, see section ››› page 156.  
With the ignition switched on, the Front Assist  
can be deactivated or activated as follows:  
●
●
Other vehicles crossing the vehicle’s path.  
In the case of pedestrians or cyclists standing  
or approaching in the opposite direction.  
●
In the infotainment system: press the func-  
Manual activation and deactivation  
of the function  
tion button > Assistants > Smart Assistants  
> Front Assist ››› page 35.  
When Front Assist is disabled on the instru-  
Operating limitations  
ment cluster, the indication  
played.  
will be dis-  
In the following situations, the Front Assist may  
work late or in an undesirable manner. The fol-  
lowing icon is displayed on the instrument  
cluster, along with the message Front As-  
sist with limitations.  
Each time the ignition is switched on, the Front  
Assist will reappear as active.  
Activating or deactivating the pre-warning  
(advance warning)  
●
If the Front Assist or the front camera are  
disabled or broken.  
Fig. 132 On the screen of the instrument  
panel Front Assist switched oꢁ message.  
The advance warning can be switched on or  
oꢁ in the infotainment system using the func-  
●
If the radar sensor or the front camera are  
dirty or covered.  
tion button  
> Assistants > Smart Assistants  
Front Assist indicators appear on the instru-  
ment panel display.  
●
●
On taking tight bends or complex paths.  
When pressing the accelerator ꢀrmly or at  
> Front Assist ››› page 35.  
The system will store the setting for the next  
time the ignition is switched on.  
The Front Assist is active whenever the ignition  
is switched on. At the time of starting the ig-  
nition, the Front Assist may not be available  
full throttle.  
●
If the ESC is adjusting or is broken.  
173  
Assistant systems  
CUPRA recommends keeping advance warning  
active.  
The system will store the setting for the next  
time the ignition is switched on.  
Lane Assist system  
Depending on the vehicle’s infotainment sys-  
tem the advance warning function may be  
adapted in the following modes:  
CUPRA recommends having the dodge and  
turn assistance systems activated except in the  
Introduction  
The Lane Assist System helps the driver stay  
in his/her lane within the physical limits of the  
system. This function is not suitable and is not  
designed to keep the vehicle automatically in  
the lane.  
exceptions described in section ››› page 174 .  
●
●
●
●
Advance  
Medium  
SEAT recommends having the dodge and turn  
assistance systems activated except in the ex-  
ceptions described in section ››› page 174.  
Delayed  
Deactivated  
Using the camera located in the windscreen,  
the Lane Assist system detects the lane boun-  
daries dividing the lanes in which the vehi-  
cle is travelling. If the vehicle gets too close  
to the detected lane limits, the system alerts  
the driver through a corrective motion of the  
steering wheel. The driver can cancel the  
steering corrective action at any time.  
Deactivating Front Assist temporarily in the  
following situations  
CUPRA recommends driving with the function  
in “Medium” mode.  
In the following situations the Front Assist  
should be deactivated due to the system's limi-  
tations:  
Switching distance warning on and oꢀ  
The distance warning can be activated or de-  
activated in the infotainment system using the  
●
●
●
When the vehicle is to be towed.  
If the vehicle is on a test bed.  
function button  
> Assistants > Smart Assis-  
No warning is produced with the turn signals  
activated, given that the Lane Assist system un-  
derstands that a lane change is required.  
If the radar sensor or the front camera are  
tants > Front Assist ››› page 35.  
The system will store the setting for the next  
time the ignition is switched on.  
faulty.  
●
If the radar sensor or the front camera have  
suꢁered a violent blow.  
System limits  
CUPRA recommends having the safety dis-  
tance warning activated except in the excep-  
●
●
If it intervenes several times unnecessarily.  
If the radar sensor or the front camera are  
Use the Lane Assist system only on large, well-  
maintained motorways and highways.  
tions described in section ››› page 174.  
temporarily covered by an accessory.  
The system is not available under the following  
conditions:  
Activate or deactivate the dodge and turn  
assistant  
●
When the vehicle is going to be loaded onto  
transportation.  
●
The driving speed allowed is below approx.  
●
If the windscreen is damaged in an area that  
The dodge and turn assistance systems can  
be activated or deactivated in the infotain-  
55 km/h (30 mph).  
covers the vision of the front camera.  
●
●
●
The system has not detected any lane lines.  
On tight bends.  
ment system using the function button  
>
Assistants > Smart Assistants > Front Assist  
››› page 35.  
Temporarily in very sporty driving situations.  
174  
LaneAssistsystem
●
If the turn signal is switched on before a  
Driving with the Lane Assist System  
●
Please observe the indications on the in-  
manual lane change.  
strument panel and act as is necessary if the  
traꢀic situation permits.  
●
If the driver ꢀrmly rectiꢀes a system interven-  
tion.  
●
In the following situations there may be  
undesired interventions of the system or it  
may be that the system does not intervene at  
all. In these situations, special attention is re-  
quired from the driver and, where appropri-  
ate, the temporary deactivation of the lane  
assist warning system:  
●
If a lane marking is crossed despite system  
intervention.  
●
If the driver does not react to a request to  
intervene.  
–
–
In very sporty driving situations.  
WARNING  
In adverse weather conditions and roads  
The intelligent technology in the Lane Assist  
system cannot change the limits imposed by  
the laws of physics and by the very nature of  
the system. Careless or uncontrolled use of  
the Lane Assist system may cause accidents  
and injury. The system is not a replacement  
for driver awareness or manoeuvres when  
driving.  
in poor condition.  
Fig. 133 On the instrument cluster screen:  
indications of the lane assist system.  
–
When passing through areas undergoing  
works.  
1
Yellow line: The system intervenes assisting  
on the represented side.  
–
Before gradient changes of grade and  
river beds.  
●
Always observe the vehicle surroundings  
carefully and drive proactively.  
2
White line: Lane line detected. The system  
does not intervene.  
●
Always adapt your speed and the distance  
●
When the area of vision of the camera be-  
comes dirty, covered or is damaged, the Lane  
Assist system function can be aꢀected.  
Depending on the equipment, additional de-  
tails of the lane marking line currently detec-  
ted by the camera, e.g. dashed road markings,  
can also be displayed on the instrument cluster  
screen.  
to the vehicles ahead in line with visibility,  
weather conditions, the condition of the  
road and the traꢀic situation.  
●
Always keep your hands on the steering  
wheel so it can be turned at any time. The  
responsibility of staying in the lane is always  
the driver's.  
Depending on the equipment, there is  
also an indication on the Head-up-Display  
●
The Lane Assist system does not detect  
››› page 23.  
all road markings. The road surfaces, road  
structures or objects in poor condition can  
be incorrectly detected as road markings un-  
der certain circumstances by the Lane Assist  
system. Immediately counter any unwanted  
intervention of the system.  
Control lamps  
Lights up green  
Lane Assist system active and availa-  
ble.  
175  
Assistant systems  
Driver intervention prompt  
Note  
Lights up yellow  
The Lane Assist system intervening  
with a rectiꢀcation of the steering.  
If the steering is not corrected manually, the  
system prompts the driver through an indi-  
cation on the instrument panel display and  
acoustic warnings.  
If the lane departure warning assistant is  
faulty, it may switch oꢀ automatically.  
If no control lamp lights up, the system is not  
ready to regulate on either side (passive state).  
Troubleshooting  
If no reaction is obtained from the driver, the  
system switches to a passive state.  
Switching the lane assist system on or oꢀ  
Lane Assist is not available  
Depending on the equipment, Emergency As-  
sist activates if it is turned on in the infotain-  
ment system.  
In some countries, the Lane Assist System is  
always activated when the ignition is switched  
on. The connection status is shown in the  
Driver assistance menu of the Infotainment  
system or the driver assistance systems menu  
after pressing the corresponding button.  
These menus can be used to activate and de-  
activate the system.  
The control lamp switches on yellow. A rele-  
vant warning is also displayed on the instru-  
ment panel screen.  
Regardless of the steering manoeuvres,  
through an indication on the instrument panel  
display and acoustic warnings, the driver is also  
prompted to drive through the centre of the  
lane if the steering correction lasts more than  
reasonable.  
●
The ꢀeld of vision of the camera is dirty.  
Clean the windscreen ››› page 313.  
The visibility of the camera is diminished due  
to accessories or adhesives.  
●
The Lane Assist system is designed to actively  
intervene as of approximately 60 km/h (35  
mph) and if it has detected the lane bounda-  
ries (system status: active).  
●
There is a fault or a defect. Turn the drive  
system oꢁ and on again.  
Steering wheel vibration  
The following situations may result in a steering  
wheel vibration:  
The system behaves diꢀerently than expec-  
ted  
If the control lamp of the instrument cluster  
display is oꢁ, it means that the system is con-  
nected but not ready to intervene or it is dis-  
connected.  
●
The lane ceases to be recognised during a  
●
The camera has been altered or damaged,  
e.g. because of damage caused to the wind-  
screen. Check for visible damage.  
sudden intervention in the direction of the sys-  
tem.  
When you activate a turn signal, the system  
temporarily goes into a passive state in order to  
allow manual lane change.  
It is also possible to select steering wheel vibra-  
tion in the Vehicle menu of the infotainment  
system. In this case, when a vehicle with Lane  
Assist switched on crosses over a detected lane  
marking, the steering wheel will vibrate.  
●
Do not mount objects on the steering wheel.  
If the problem persists, consult a specialised  
workshop.  
An energetic rotation or rectiꢀcation of the  
steering wheel by the driver causes the system  
to temporarily switch to a passive state.  
176  
DrivingAssist(Travel Assist)  
How to know if the vehicle is ꢁtted with  
Travel Assist  
Status display  
Note  
After switching on the ignition, it may take a  
few seconds before a fault is detected in the  
system.  
The vehicle is ꢀtted with Travel Assist if the  
multifunction steering wheel has the  
ton.  
but-  
Note  
Speed range  
If Lane Assist is unavailable, Emergency Assist  
and Travel Assist will be unavailable as well.  
Travel Assist regulates at speeds over 0 km/h  
(0 mph). The set speed can be adjusted at  
speeds over 20 km/h (15 mph).  
Driving Assist (Travel As-  
sist)  
Fig. 134 On the instrument cluster display:  
display of active regulation (schematic  
representation).  
Driving with Travel Assist  
Travel Assist automatically controls the accel-  
erator pedal, the brakes and the steering.  
In addition, Travel Assist may, within its limi-  
tations, decelerate the vehicle until it stops  
behind another that stops and automatically  
starts again.  
Introduction  
1
The colour of the lane markings indicates  
the status of the adaptive lane guidance  
function.  
Travel Assist combines adaptive cruise control  
(ACC) and the adaptive lane guidance func-  
tion. Within the limitations of the system, the  
vehicle can maintain a distance from the vehi-  
cle in front that is preselected by the driver  
and remain in the preferred position within the  
lane.  
●
Yellow: adaptive lane guidance function  
You can override assisted adjustment at all  
times.  
active.  
●
White: adaptive guidance function avail-  
able.  
●
Grey: passive adaptive lane guidance  
Travel Assist uses the same sensors as Adaptive  
Cruise Control (ACC) and Lane Assist. There-  
fore, carefully read the information about  
function.  
2
Distance set.  
Depending on the equipment, there is  
also an indication on the Head-up-Display  
››› page 23.  
Depending on the equipment, additional de-  
tails, e. g. dashed road markings and vehicles  
in front, can also be shown on the instrument  
cluster display.  
the ACC ››› page 163 and the Lane Assist  
››› page 174 and take into account the limita-  
tions of the systems and the indications given  
in the information.  
177  
Assistant systems  
Control lamps indicate the status of the system  
on the instrument panel display:  
This makes it possible to increase the availabil-  
ity of Travel Assist in certain driving situations,  
e.g. when the road markings are incomplete or  
missing on one side of the road.  
●
Do not use Travel Assist when visibility is  
bad, on steep roads, on windy roads or in slip-  
pery circumstances (e. g., snow, ice, rain or  
loose gravel), or on ꢂooded roads.  
Green lamp: travel Assist active, adaptive  
cruise control and adaptive lane guid-  
ance function are active.  
●
Do not use Travel Assist oꢀroad or on roads  
Requirements:  
where the surface is not ꢁrm. Travel Assist  
has been designed for use on paved roads  
only.  
●
●
Partially green lamp: Travel Assist active,  
adaptive cruise control active and adap-  
tive lane guidance function passive.  
Travel Assist is activated.  
Your CUPRA Connect subscription is activa-  
ted.  
●
Travel Assist does not react to people or  
Grey lamp: Travel Assist deactivated, not  
regulating.  
●
●
●
You have an Internet connection.  
animal or vehicles crossing your path or  
which approach you head-on in the same  
lane.  
The use of online map data is activated.  
The upload function for all map data collec-  
●
Brake immediately if Travel Assist does not  
Driver intervention prompt  
ted from your vehicle is enabled (optional).  
slow down enough.  
If you remove your hands from the steering  
wheel, after a few seconds the system asks  
you to take over the steering with an indication  
on the instrument panel display and acoustic  
warnings.  
●
Brake immediately when instructed to do  
WARNING  
so on the instrument cluster display, or if  
Travel Assist does not reduce speed suꢀi-  
ciently.  
The Travel Assist smart technology cannot  
overcome the limits imposed by the laws of  
physics and it only works within the limits  
of the system. If Travel assist is used negli-  
gently or involuntarily, it may cause serious  
accidents and injuries. The system is not a  
replacement for driver awareness.  
●
Brake when the vehicle continues to move  
If you do not react, Travel Assist is deactivated.  
forward without it being desired after an indi-  
cation to brake.  
Depending on the equipment, Emergency As-  
sist activates if it is activated in the infotain-  
ment system.  
●
If possible, do not wear gloves while driv-  
ing. The system could interpret this as no  
driving activity.  
●
Bear in mind the system limitations and  
the indications regarding the control of the  
Adaptive Cruise Control (ACC) and Lane As-  
sist.  
Travel Assist with online data1)  
●
Keep your hands on the steering wheel at  
all times, to ensure you have control over the  
steering at all times. The driver is always re-  
sponsible for keeping the vehicle in its own  
lane.  
Travel Assist with online data uses online map  
data to enhance its performance (depending  
on equipment and not available in all coun-  
tries).  
●
Adapt your speed and safety distance to  
the vehicle in front of you at all times to  
suit visibility, weather, road and traꢀic condi-  
tions.  
●
Always be prepared to adjust the speed  
yourself.  
1)  
Not available on all markets.  
178  
DrivingAssist(Travel Assist)  
●
When ACC is regulating, Travel Assist main-  
Using the lane change assist  
Note  
tains the current speed and the preset dis-  
tance to the vehicle in front.  
Online services provided and activated  
through CUPRA Connect (depending on de-  
vice and country) may enhance the opera-  
tion of Travel Assist when connected to the  
Internet.  
Lane Change Assist uses the same sensor sys-  
tem as Side Assist. Therefore, read the infor-  
mation on Side Assist ››› page 183 carefully  
and observe the limits of the system and the  
notes that it displays.  
When lane markings are detected, the vehicle  
is also kept in the lane by steering movements.  
●
If ACC is not regulating, Travel Assist remains  
selected but in a passive (unregulated) status.  
Activating the convenience turn signal on a  
motorway, provided that the prerequisites are  
met and no vehicles have been detected in the  
vicinity, provides assistance when the vehicle is  
changing lanes.  
1. Press the button.  
Operating Travel Assist  
Travel Assist switches to the active system  
status, depending on the driving situation.  
The indicator lamp for the driving situation  
lights up on the instrument cluster display. A  
message is also displayed.  
Prerequisites  
Lane change assist is only available, depend-  
ing on the vehicle's equipment, when driving  
forwards on multi-lane motorways included in  
the Infotainment system’s navigation data, and  
when travelling faster than 90 km/h.  
Interrupting the adjustment  
1. Brieꢂy press the button  
.
OR: press the brake pedal.  
The set distance remains saved.  
Travel Assist must also be activated.  
Fig. 135 Left side of the multifunction  
steering wheel  
Switch to ACC  
1. Press the  
steering wheel.  
button on the multi-function  
Switch on and start regulation  
1. While driving with ACC activated, press  
on the multifunction steering wheel.  
The vehicle switches from Travel Assist to  
the ACC system status corresponding to  
the driving situation.  
The vehicle switches from ACC to Travel  
Assist.  
Making other adjustments  
Depending on the driving situation, the vehi-  
cle switches to the following system statuses in  
Travel Assist:  
All other aspects of Travel Assist are controlled  
like the ACC.  
179  
Assistant systems  
1. Access the assistant menu.  
2. Select Travel Assist.  
When changing lanes, the vehicle automati-  
cally activates the turn signal on the corre-  
sponding side. Once the lane change is com-  
plete, the turn signal automatically switches  
oꢁ.  
Status display  
3. Activate or deactivate lane change assist as  
a sub-function of Travel Assist.  
Note  
WARNING  
●
If a fault occurs in the system, the lane  
change assist may automatically switch oꢀ or  
be interrupted during the lane change.  
The sensor system cannot reliably detect all  
objects in the surroundings and operates ex-  
clusively within the limits of the system. If you  
use the lane change assist irresponsibly, ac-  
cidents and serious injuries can occur. The  
system is not a replacement for driver aware-  
ness.  
●
If Side Assist is not available, lane change  
assist is not available either.  
Activating lane change assist while driving  
Fig. 136 On the instrument cluster screen:  
lane change assist display (schematic  
representation).  
1. Press the  
button.  
●
Before changing lanes, make sure it is safe  
to do so. In particular, rapidly approaching  
objects may not be detected in time.  
Lane change assist is activated. The arrows  
of your own lane on the instrument cluster  
display are grey ››› Fig. 136  
1
●
Lane highlighted, the assisted lane change  
Keep your hands on the steering wheel at  
2
all times and be prepared to control your own  
speed and direction of travel.  
takes place.  
2
Arrows in the vehicle's own lane show the  
status of the lane change assist.  
Changing lanes  
If the system detects no objects in the detec-  
tion ꢀeld of the sensor system and an assisted  
lane change to an adjacent lane is possible, the  
corresponding lane is shown in the instrument  
cluster display next to the driver’s own lane.  
The arrow on the corresponding side of the  
2
Turning oꢀ the lane change assist  
●
Grey: changing lanes to the respective  
side of the lane is not possible.  
1. Brieꢂy press the button  
.
●
Orange: Changing lanes is possible on  
OR: Press the brake pedal.  
the respective side of the lane.  
Lane change assist is deactivated. Travel  
Assist is also deactivated.  
lane is displayed in white ››› Fig. 136  
.
Activating and deactivating lane change as-  
sist  
1. When the convenience turn signal is ac-  
tivated on the desired side, the vehicle  
changes lane. A message is also displayed.  
You can activate and deactivate lane change  
assist in the Infotainment system.  
180  
EmergencyAssist  
●
You have let go of the steering wheel for  
Lane change assist is interrupted or unavail-  
able  
Troubleshooting  
a long time, or the system limits have been  
reached. Immediately take hold of the steering  
wheel and take control of the vehicle.  
Travel Assist is not available or does not  
work as expected  
A message about this is shown on the instru-  
ment cluster display.  
The control lamp switches on yellow. A rele-  
vant warning is also displayed on the instru-  
ment panel screen.  
●
The vehicle has stopped detecting lane  
Travel Assist disconnects automatically  
markings.  
●
Vehicles without Emergency Assist:  
●
●
You have let go of the steering wheel  
You are applying too much force to the  
You have released the steering wheel for a long  
period.  
●
There is a fault in the sensors. Check the  
causes and solutions described in the informa-  
tion about the ACC ››› page 167 or the Lane  
Assist ››› page 176.  
steering wheel.  
●
There is a fault or a defect. Turn the drive  
●
You have turned on the turn signal too many  
system oꢁ and on again.  
times, or the turn signal lever is stuck.  
●
If the problem persists, consult a specialised  
●
There is a fault or a defect. Turn the drive  
system oꢁ and on again.  
●
The driving speed is lower than around  
workshop. CUPRA recommends visiting a spe-  
cialised CUPRA dealer or any SEAT dealership.  
85 km/h.  
●
●
The system limits are exceeded.  
●
The vehicle has detected objects in the vi-  
If the problem persists, consult a specialised  
cinity that prevent an assisted lane change.  
The adjustment is interrupted unexpectedly  
workshop. CUPRA recommends visiting a spe-  
cialised CUPRA dealer or any SEAT dealership.  
●
You are not on a multi-lane motorway.  
●
Vehicles without lane departure warning:  
You have turned on the turn signal.  
Grip the steering wheel  
Emergency Assist  
Lane assist not available  
The warning lamp lights up white, and a mes-  
sage is shown on the instrument cluster dis-  
play.  
How it works  
The control lamp switches on yellow. A rele-  
vant warning is also displayed on the instru-  
ment panel screen.  
Emergency Assist can detect whether there is  
inactivity by the driver and can automatically  
keep the car in its lane and stop it altogether  
if necessary. This way the system can actively  
help avoid an accident or reduce its conse-  
quences.  
●
You released the steering wheel for a few  
seconds. Take hold of the steering wheel and  
take control of the vehicle.  
●
There is a fault in the sensors. Check the  
described causes and the corrective measures  
in the Side Assist information.  
●
If the problem persists, consult a specialised  
Grip the steering wheel  
workshop. CUPRA recommends visiting a spe-  
cialised CUPRA dealer or any SEAT dealership.  
Emergency Assist uses the same sensors as  
Adaptive Cruise Control (ACC) and Lane As-  
sist. Therefore, carefully read the information  
about the ACC ››› page 163 and Lane Assist  
The warning lamp lights up red and a message  
is shown on the instrument cluster display. De-  
pending on the situation, an audio warning  
sounds or the steering wheel vibrates.  
181  
Assistant systems  
The following happens as soon as the vehicle  
stops:  
››› page 174 and take into account the limita-  
tions of the systems and the indications given  
in the information.  
WARNING  
The smart technology ꢁtted into the Emer-  
gency Assist cannot overcome the limits im-  
posed by the laws of physics; it only works  
within the limits of the system. The driver is  
responsible for driving the vehicle.  
●
●
●
●
The electronic parking brake is activated.  
All doors are unlocked.  
Driver intervention prompt  
The interior lighting comes on.  
If the emergency assist detects that the driver  
is not actively doing anything, he or she is  
prompted to take control of the vehicle by  
audio warnings and a brief application of the  
brake. In addition, a warning is shown on the  
instrument cluster display and the volume of  
the infotainment system is lowered.  
Depending on the features, an emergency  
●
Adapt your speed and safety distance to  
call (eCall) is made.  
the vehicle in front of you at all times to suit  
the visibility, weather, road and traꢀic condi-  
tions.  
Connecting and disconnecting  
Emergency Assist can be switched on and oꢁ  
in the assistants menu of the infotainment sys-  
tem.  
●
The Emergency Assist cannot always avoid  
accidents or serious injuries by itself.  
Depending on the equipment, the driver’s seat  
belt is tightened at the same time.  
●
If the radar sensor or the camera are cov-  
ered or have been altered or damaged, the  
system may intervene on the brakes or on the  
direction in an inappropriate manner.  
When connected, the Emergency Assist is only  
activated if the following requirements are met:  
System intervention  
●
The Travel Assist or the Lane Assist are  
●
The Emergency Assist does not react to  
switched on.  
If the driver does not react, the system can  
brake the vehicle and keep it in its lane. The  
following control lamp lights up on the instru-  
ment cluster display:  
people or animal or vehicles crossing your  
path or which approach you head-on in the  
same lane.  
●
The system has detected a road lane marking  
on both sides of the vehicle.  
Note  
The system is regulating.  
WARNING  
If the emergency assist is faulty, it may switch  
oꢀ automatically.  
If the Emergency Assist Intervenes inoppor-  
tunely, serious accidents and injuries may  
occur.  
You can cancel the adjustment at any time by  
moving the steering wheel, over-accelerating  
or braking.  
Note  
●
If the vehicle behaves diꢀerently than ex-  
If Lane Assist is unavailable, Emergency Assist  
will be unavailable as well.  
pected, interrupt the intervention of the  
Emergency Assist by over-accelerating, brak-  
ing or moving the steering wheel.  
While the emergency assistant is in operation,  
other road users are warned as follows:  
●
The hazard warning lights are switched on  
●
Do not use Travel Assist or Lane Assist.  
soon after.  
Have the system checked by a specialised  
●
The horn sounds (depending on the speed).  
workshop.  
182  
Lane departurewarning(Side Assist)  
The lane width is not detected individually, but  
is rather pre-conꢀgured in the system. Thus  
if you are driving in wide lanes or in between  
two lanes, the indications may be incorrect.  
Furthermore, the system can detect vehicles  
driving in the lane next to you (if there are any),  
and can also detect stationary objects such as  
dividers, and thus give an incorrect indication.  
Troubleshooting  
●
Keep your hands on the wheel at all times  
to be ready to intervene in the steering at any  
time.  
Emergency assist is not available  
●
Pay attention to the indicator lamps that  
The control lamp switches on yellow. A rele-  
vant warning is also displayed on the instru-  
ment panel screen.  
may come on in the external rear view mir-  
rors and on the instrument cluster, and fol-  
low any instructions they may give.  
●
There is a fault or a defect. Turn the drive  
●
The lane departure warning could react to  
system oꢁ and on again.  
any special constructions that might be pres-  
ent to the sides of the vehicle, e.g. high or  
irregular dividers. This may cause erroneous  
warnings.  
Physical limitations inherent to the system  
●
If the problem persists, switch oꢁ the Emer-  
gency Assist and go to a specialised workshop.  
In some situations the lane departure warning  
may not interpret the traꢁic situation correctly.  
I.e. in the following situations:  
●
Never use the lane departure warning on  
The buttons react diꢀerently than expected  
unpaved roads. The lane departure warning  
has been designed for use on paved roads.  
●
●
●
●
●
Moisture, dirt and grease can limit the opera-  
tion of the buttons.  
on tight bends;  
in the case of lanes with diꢁerent widths;  
in areas with signiꢀcant gradient changes;  
in adverse weather conditions;  
●
Always pay attention to the vehicle's sur-  
●
Make sure the buttons are always clean and  
roundings.  
dry.  
●
The control lamps of the lane departure  
warning may have limited functionality due  
to solar radiation.  
in the case of special constructions to the  
side of the vehicle, e.g., high or irregular divid-  
ers.  
Lane departure warning  
(Side Assist)  
Note  
WARNING  
If Side Assist does not work as described in  
this chapter, stop using it and contact a spe-  
cialised workshop.  
Introduction  
The smart technology incorporated into Side  
Assist cannot overcome the limits imposed  
by the laws of physics; it only works within the  
limits of the system. Accidents and severe  
injury may occur if Side Assist is used negli-  
gently or involuntarily. The system is not a  
replacement for driver awareness.  
The lane departure warning uses radar sen-  
sors to monitor the areas behind the vehicle  
››› page 13. The system does this by measur-  
ing the vehicle's distance from other vehicles  
and its speed diꢁerential. The lane departure  
warning will not work at speeds of less than  
approx. 15 km/h (9 mph).  
●
Adapt your speed and safe distance to the  
vehicle in front of you at all times to suit visi-  
bility, weather, road and traꢀic conditions.  
183  
Assistant systems  
When the lane departure warning is ready to  
operate, the indications in the control lamps  
will turn on brieꢂy as conꢀrmation.  
Driving with Side Assist  
Flashes  
A vehicle has been detected in the adjacent  
lane and the turn signal has been engaged in  
the direction of the detected vehicle.  
When the vehicle is restarted, the last adjust-  
ment in the system will remain active.  
For vehicles that are also equipped with Lane  
Assist ››› page 174, a warning to switch lanes  
will also appear even though the turn signal  
has not been engaged (Lane Assist “Plus”).  
Indication on the exterior mirror  
The control lamp provides an indication on the  
corresponding side regarding the traꢁic situa-  
tion behind the vehicle, if it is deemed to be  
critical. The control lamp on the left-hand side  
indicates the traꢁic situation to the rear left of  
the vehicle, and the control lamp on the right-  
hand side indicates the traꢁic situation to the  
rear right of the vehicle .  
The control lamps light up when the ignition is  
switched on and should turn oꢁ after approxi-  
mately 2 seconds. This is the time taken for the  
function check.  
Fig. 137 Control lamp of the lane  
departure warning.  
If there are no indications from the control  
lamp of the lane departure warning, this means  
that the lane departure warning has not detec-  
ted any other vehicles at the rear area.  
In the case of retroꢀtted tinted windows or  
windows with tinted ꢀlm, the indications of the  
external mirrors may not be seen clearly.  
Keep the external mirrors clean and free of  
snow and ice, and do not cover them with ad-  
hesives or other similar materials.  
When the exterior lighting is low, the intensity  
with which the control lamps come on is dim-  
med. The user can modify the intensity of the  
control lamps with up to 5 levels in the infotain-  
ment system menu.  
It lights up  
It turns on once brieꢂy: the lane departure  
warning is activated and ready to operate, i.e.  
when activating the system.  
Lane assist Plus.  
Fig. 138 Control lamp of the lane  
departure warning.  
The Lane Assist Plus function can be used by  
activating the Lane Assist ››› page 174 and  
Side Assist functions. In this case its functions  
are expanded as described below.  
It lights up continuously: the lane departure  
warning has detected a vehicle in the blind  
spot.  
Connecting and disconnecting  
Side Assist can be switched on and oꢁ by ac-  
cessing the Assistants menu in the infotain-  
ment system.  
If the driver initiates a lane change manoeuvre  
in a potential critical situation:  
184  
Lane departurewarning(Side Assist)  
●
The lamp ꢂashes in the corresponding rear-  
The faster the vehicle approaches, the sooner  
an indication will be displayed in the control  
lamp, because the lane departure warning  
takes into account the speed diꢁerential with  
other vehicles. Thus even though the distance  
from the other vehicle is identical, the indica-  
tion will appear sooner in some cases and later  
in others.  
view mirror even though the turn signal has not  
been activated.  
●
The steering wheel vibrates to warn the  
driver of the risk of collision.  
●
torque is applied to correct the steering and  
return the vehicle to its lane.  
Driving situations  
Fig. 140 Schematic diagram:  
Overtaking in the central lane and then  
joining the right lane. Side Assist  
indication on the right hand side.  
In the following situations, an indication will be  
displayed in the control lamp ››› Fig. 139  
(arrow) or ››› Fig. 140 (arrow):  
●
When being overtaken by another vehicle  
››› Fig. 139  
.
Fig. 139 Schematic diagram: Overtaking  
with traꢁic behind the vehicle. Side Assist  
indication on the left hand side.  
●
When passing another vehicle ››› Fig. 140  
with a speed diꢁerential of approx. 10 km/h  
(6 mph). If the vehicle is passing at a consid-  
erably higher speed, no indication will be dis-  
played.  
185  

Related Topics

Popular Owner Manuals