2002-2008 Cupra Born SUV Wheels and tyres User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Wheels and tyres for Your Cupra Born SUV First Generation (2002-2008)

Wheels and tyres  
Low proꢀle tyres  
Foreign objects inserted in the tyre  
Wheels and tyres  
●
Low proꢀle tyres have a wider tread, a larger  
wheel diameter and a lower sidewall height.  
Therefore, its driving behaviour is more agile.  
Do not remove foreign bodies if they have  
penetrated through the tyre wall!  
Important information  
about wheels and tyres  
●
If the vehicle comes with a tyre mobility sys-  
tem, where necessary seal the damaged tyre as  
Low proꢀle tyres may deteriorate more quickly  
than standard tyres, for instance due to  
strong knocks, potholes, manhole covers and  
kerbs. Correct tyre pressure is very important  
››› page 298.  
To avoid damage to tyres and wheels, drive  
with special care when driving on roads in poor  
condition.  
shown in section ››› page 308. Use a special-  
ised workshop for repair or replacement. To do  
so, CUPRA recommends going to a specialised  
CUPRA dealer or any SEAT dealership.  
General notes  
●
When driving with new tyres, be especially  
careful during the ꢀrst 600 km (300 miles).  
The sealant at the lower part of the tyre tread  
wraps around the foreign body and provision-  
ally seals the tyre.  
●
If you have to drive over a kerb or similar ob-  
stacle, drive very slowly and as near as possible  
at a right angle to the obstacle.  
Visually check your wheels every 3000 km.  
●
Check from time to time if the tyres are  
Tyres with directional tread pattern  
If the tyres or rims have received a heavy im-  
pact or have been damaged, have a special-  
ised workshop check whether or not it is nec-  
essary to change the tyre.  
damaged (punctures, cuts, cracks or dents).  
Remove any foreign objects embedded in the  
treads.  
An arrow on the tyre sidewall indicates the di-  
rection of rotation on single drive tyres. Always  
note the direction of rotation indicated when  
mounting the wheel. This makes sure that op-  
timal use is made of tyre properties in terms of  
aquaplaning, grip, excessive noise and wear.  
●
Damaged wheels and tyres must be replaced  
Low proꢀle tyres may deteriorate more quickly  
than standard tyres.  
immediately.  
●
●
Keep grease, oil and fuel oꢁ the tyres.  
Replace any missing valve caps as soon as  
Concealed damage  
Subsequent ꢀtting of accessories  
possible.  
Damage to tyres and rims is often not readily  
visible. If you notice unusual vibration or the  
car pulling to one side, this may indicate that  
one of the tyres is damaged. Reduce speed im-  
mediately if there is any reason to suspect that  
damage may have occurred. Inspect the tyres  
for damage. If no external damage is visible,  
drive slowly and carefully to the nearest speci-  
alised workshop and have the car inspected.  
If you wish to change or ꢀt wheels, rims or  
wheel trims, we recommend that you consult  
with a specialised CUPRA Service or SEAT Oꢁi-  
cial Service centre for advice regarding current  
technical recommendations.  
●
Mark the wheels before taking them oꢁ so  
that they rotate in the same direction when put  
back.  
●
When removed, the wheels or tyres should  
be stored in a cool, dry and preferably dark  
place.  
Speed symbols  
The speed rating indicates the maximum  
speed permitted for the tyres.  
296  
Important informationaboutwheels and tyres  
New wheels and tyres  
P
Q
R
S
max. 150 km/h (93 mph)  
max. 160 km/h (99 mph)  
max. 170 km/h (106 mph)  
max. 180 km/h (112 mph)  
max. 190 km/h (118 mph)  
max. 200 km/h (124 mph)  
max. 210 km/h (130 mph)  
max. 240 km/h (149 mph)  
max. 240 km/h (149 mph)  
max. 270 km/h (168 mph)  
max. 300 km/h (186 mph)  
If the type of spare wheel is diꢁerent form  
the normal wheels — e.g. in the case of win-  
ter tyres or particularly wide tyres — the spare  
wheel should only be used temporarily in the  
event of a puncture, and the vehicle should be  
driven with care. Reꢀt the normal road wheel  
as soon as possible.  
It is best to have all wheels and tyres serviced  
by a specialised workshop. There they have the  
required knowledge, the special tools and the  
corresponding spare parts.  
T
●
The vehicle is factory ꢀtted with original  
U
H
V
Z
W
Y
CUPRA tyres with optimised rolling resistance.  
The original CUPRA tyres are marked with the  
symbol . Only with these tyres can the speci-  
ꢀed energy consumption and range be ach-  
ieved. When buying new tyres, always make  
sure they have optimised rolling resistance  
In vehicles with four-wheel drive, the 4 wheels  
must be ꢀtted with tyres of the same brand,  
type and tread so that the traction system is  
not damaged by a diꢁerence in the number of  
turns of the wheels. Therefore, in the event of  
a puncture, only a spare wheel with the same  
perimeter as normal tyres should be used.  
››› page 138.  
●
Even winter tyres lose their grip on ice. If you  
Manufacturing date  
have installed new tyres, drive the ꢀrst 600 km  
carefully and at a moderate speed.  
WARNING  
The manufacturing date is also indicated on  
the tyre sidewall (or on the inside face of the  
wheel):  
●
New tyres do not have maximum grip dur-  
●
All four wheels must be ꢀtted with tyres  
ing the ꢀrst 600 km. Drive particularly care-  
fully to avoid possible accidents.  
of the same type, size (rolling circumference)  
and, if possible, tread pattern.  
DOT ... 2220 ...  
●
Never drive with damaged tyres. This may  
●
When changing tyres, do not change just  
cause an accident.  
it means, for example, that the tyre was manu-  
factured in the 22nd week of 2020.  
one; change at least two on the same axle.  
●
If you notice unusual vibrations or if the  
●
If you want to equip your vehicle with a com-  
vehicle pulls to one side when driving, stop  
the vehicle immediately and check the tyres.  
bination tyres and rims that are diꢁerent to  
those ꢀtted in the factory, inform your special-  
●
Never use old tyres or those with an un-  
ised workshop before purchasing them ›››  
known history of use.  
The sizes of the rims and tyres approved for  
your vehicle are listed in the vehicle documen-  
tation (e.g. EC Certiꢀcate of Conformity or  
COC document1)). The vehicle documentation  
varies depending on the country of residence.  
1)  
COC = certiꢀcate of conformity.  
297  
Wheels and tyres  
Tyre life  
the vehicle when it drives at over 40 km/h. It  
is advisable to remove ice and snow from the  
inside of the wheels using hot water.  
WARNING  
●
Use only combinations of tyres and rims,  
as well as suitable wheel nuts, approved by  
CUPRA. Otherwise the vehicle may be dam-  
aged, causing an accident.  
●
If you drive on dirt or gravel tracks, the  
likelihood of stones becoming trapped inside  
wheel rims with plastic elements increases  
when driving at high speed or in a sporty  
manner. If you see that there are stones trap-  
ped between the aluminium wheel rim and  
the insert, you can attempt to remove them  
using pressurised water.  
●
For technical reasons it is not possible to  
use wheels of other vehicles; in some ca-  
ses not even wheels from the same vehicle  
model should be used.  
●
Always ensure that the tyres you have  
chosen have adequate clearance. When se-  
lecting replacement tyres, do not rely en-  
tirely on the nominal tyre size marked on the  
tyre, since the nominal tyre size can diꢁer  
signiꢀcantly depending on the manufacturer.  
Lack of clearance can damage the tyres or  
the vehicle and, as a result, endanger road  
safety. Accident hazard!  
For the sake of the environment  
Old tyres must be disposed of according to  
the laws in the country concerned.  
Note  
Fig. 195 Location of the tyre pressure  
sticker.  
●
Only use tyres that are over 6 years old in  
●
A CUPRA Service Centre should be consul-  
an emergency, and drive with due care.  
ted to ꢀnd out whether wheels or tyres of  
diꢁerent sizes to those originally ꢀtted by  
CUPRA can be ꢀtted, and to ꢀnd out about  
the combinations allowed between the front  
axle (axle 1) and the rear axle (axle 2).  
●
The ꢀtting of tyres with run-ꢂat properties  
Correct inꢂation pressures and sensible driving  
habits will increase the useful life of your tyres.  
is not permitted on your vehicle! Prohibited  
use can cause accidents or can damage your  
vehicle.  
●
Check tyre pressure at least once a month,  
and also prior to any long trip.  
●
If decorative hubcaps are subsequently ꢀt-  
●
Never mount used tyres if you are not sure  
of their “previous history”.  
●
The tyre pressure should only be checked  
ted, make sure that they allow enough air in  
to cool the braking system. Accident hazard!  
when the tyres are cold. Do not reduce the  
pressure of warm tyres.  
●
Models with aerodynamic wheel rims  
and/or with bolt-on plastic elements (more  
closed design) increase the likelihood of ice  
and snow accumulating on the inside. This  
should be taken into account, depending on  
the driving situations, as snow or ice accu-  
mulated in the wheels can cause vibration in  
●
Adjust tyre pressure to the load being carried  
by the vehicle ››› Fig. 195.  
●
the modiꢀed tyre pressure ››› page 306.  
In vehicles with a tyre pressure indicator, save  
298  
Important informationaboutwheels and tyres  
Wheel balance  
●
●
Avoid fast cornering and hard acceleration.  
Inspect the tyres for irregular wear from time  
●
Tyre pressure should be that indicated on  
the label when the tyres are cold at all times  
The wheels on new vehicles are balanced.  
However, certain circumstances may lead to  
imbalance (run-out), which is detected as vi-  
brations in the steering wheel.  
››› Fig. 195.  
●
of the tyres. If necessary, change the tyre  
pressure of the vehicle tyres while they are  
cold.  
to time.  
Regularly check the cold inꢂation pressure  
Tyre pressure  
The values of the tyre pressure are shown on  
the sticker label located on the read frame of  
the front left door ››› Fig. 195.  
Unbalanced wheels should be rebalanced, as  
they otherwise cause excessive wear on steer-  
ing, suspension and tyres. A wheel must also  
be rebalanced when a new tyre is ꢀtted or if a  
tyre is repaired.  
●
Regularly check your tyres for damage and  
wear.  
Insuꢁicient or excessive pressure greatly re-  
duces the useful life of the tyres and adversely  
aꢁects vehicle performance and ride. Correct  
inꢂation pressures are very important, espe-  
cially at high speeds.  
●
Never exceed the maximum permitted  
speed or loads speciꢀed for the type of tyre  
ꢀtted on your vehicle.  
Incorrect wheel alignment  
Incorrect running gear alignment causes ex-  
cessive tyre wear, impairing the safety of the  
vehicle. If you notice excessive tyre wear, you  
should check wheel alignment at a specialised  
CUPRA Service or SEAT Oꢁicial Service.  
For the sake of the environment  
The tyre pressure must be adjusted according  
to the load the vehicle is carrying. If the vehicle  
is going to be fully loaded, increase the tyre  
pressure to the maximum load value shown on  
Insuꢁicient tyre pressure increases energy  
consumption.  
the sticker label ››› Fig. 195.  
Tread wear indicators  
WARNING  
Do not forget the spare wheel when checking  
the tyre pressures: Keep this spare wheel inꢂa-  
ted to the highest pressure required for the  
road wheels.  
Unsuitable handling of the wheels and tyres  
may lead to sudden tyre pressure losses, to  
tread separation or even to a blow-out.  
●
The driver is responsible for ensuring that  
In the case of a minimised temporary spare  
wheel (125/70 R16 or 125/70 R18) inꢂate to a  
pressure of 4.2 bar as indicated on the tyre  
pressure label ››› Fig. 195.  
all of the vehicle tyres are correctly inꢂa-  
ted to the right pressure. The recommen-  
ded tyre pressure is indicated on the label  
››› Fig. 195.  
●
Check tyre pressures regularly and ensure  
Driving style  
they are maintained at the pressures indica-  
ted. Tyre pressure that is too low could cause  
overheating, resulting in tread detachment  
or even burst tyres.  
Fast cornering, heavy acceleration and hard  
braking (squealing tyres) all increase tyre wear.  
Fig. 196 Tyre proꢀle: tread wear indicators.  
299  
Wheels and tyres  
WARNING  
A special adapter is required to turn the anti-  
theft wheel bolts ››› page 303.  
The tyres must be replaced at the latest when  
the tread is worn down to the tread wear indi-  
cators. Failure to follow this instruction could  
result in an accident.  
Two-piece wheel bolts  
Two-piece wheel bolts must be used for this  
vehicle. In this type of bolt, the spherical collar  
is not ꢀrmly attached to the head.  
●
Particularly in diꢁicult driving conditions  
such as wet or icy roads. It is important that  
the tyre tread be as deep as possible and be  
approximately the same on the tyres of both  
the front and the rear axles.  
WARNING  
Wheel nuts should never be greased or oiled.  
Fig. 197 Interchanging tyres.  
●
The scant driving safety due to insuꢁicient  
●
Use only wheel bolts which belong to the  
tread depth is particularly evident in vehicle  
handling, when there is a risk of “aquaplan-  
ing” in deep puddles of water and when driv-  
ing through corners, and braking is also ad-  
versely aꢁected.  
Wear indicators around 1.6 mm high can be  
found on the base of the original tyre treads,  
ordered at regular intervals and running across  
the tread ››› Fig. 196. The letters “TWI” or  
triangles on the sidewall of the tyre mark the  
position of the wear indicators.  
wheel.  
●
If the prescribed torque of the wheel bolts  
is too low, they could loosen whilst the vehi-  
cle is in motion. Risk of accident! If the tight-  
ening torque is too high, the wheel bolts and  
threads can be damaged.  
●
The speed has to be adapted accordingly,  
otherwise there is a risk of losing control over  
the vehicle.  
The minimum permitted proꢀle depth 1) have  
been reached when the tyres have worn down  
to the wear indicators. Replace the tyres with  
NOTICE  
Wheel nuts  
See ››› page 305 to ꢀnd out the recommen-  
ded tightening torque for wheel nuts for steel  
and alloy rims.  
new ones ›››  
.
The wheel bolts and rims have been designed  
to be part of an assembly. When installing  
diꢁerent wheels (for instance alloy wheels or  
wheels with winter tyres) it is important to use  
the correct wheel bolts with the right length  
and correctly shaped bolt heads. This ensures  
that wheels are ꢀtted securely and that the  
brake system functions correctly.  
Changing wheels around  
In order to wear the wheels in a uniform man-  
ner, it is recommended to interchange them  
regularly according to the diagram ››› Fig. 197.  
The useful life of all the tyres will then be about  
the same time.  
Winter tyres  
●
Winter tyres must be ꢀtted on all four  
wheels.  
●
Only use winter tyres that are approved for  
your vehicle.  
The wheel bolts must be clean and turn easily.  
1)  
Follow the regulations of the country you are driving in.  
300  
Important informationaboutwheels and tyres  
●
Please note that the maximum permissible  
A code letter indicating the speed limit is stam-  
ped on all winter tyres ››› page 296.  
In the infotainment system's Vehicle settings  
menu, a speed warning can be set in the Tyres  
menu.  
WARNING  
speed for winter tyres may be lower than for  
summer tyres.  
Exceeding the maximum speed permitted for  
the winter tyres ꢀtted on your car can cause  
tyre failure, resulting in a loss of control of  
the vehicle – risk of accident.  
●
Also note that winter tyres are no longer ef-  
fective when the tread is worn down.  
●
After ꢀtting the wheels you must always  
Vehicles capable of exceeding these speeds  
must have an appropriate sticker attached so  
that it is visible to the driver. Suitable stickers  
are available at specialised CUPRA Services,  
SEAT Oꢁicial Service centres and specialised  
workshops. Please note the regulations to this  
eꢁect in your country.  
check the tyre pressures. When doing so,  
take into account the correct tyre pressures  
listed on the rear of the front left door frame  
››› page 298.  
In winter road conditions winter tyres will con-  
siderably improve vehicle handling. The design  
of summer tyres (width, rubber compound,  
tread pattern) gives less grip on ice and snow.  
This applies particularly to vehicles equipped  
with wide section tyres or with high speed  
tyres (code letters H, V or Y on the sidewall).  
For the sake of the environment  
When winter is over, change back to summer  
tyres at an appropriate moment. In tempera-  
tures above +7°C (+45°F), performance will be  
improved if summer tyres are used. Rolling  
noise, wear and energy consumption will all  
be reduced.  
“All-weather” tyres can also be used instead of  
winter tyres.  
Using winter tyres with V-rating  
Snow chains  
Please note that the generally applicable  
240 km/h (149 mph) speed for winter tyres  
with the letter V is subject to technical restric-  
Snow chains may only be ꢀtted to the rear  
wheels.  
Only use winter tyres of the correct type ap-  
proved for your vehicle. The sizes of these  
tyres are speciꢀed in the vehicle's documents  
(e.g. EC Certiꢀcate of Conformity or COC1)).  
The vehicle documentation varies depending  
on the country of residence.  
●
Check that they are correctly seated after  
driving for a few yards; correct the position  
if necessary, in accordance with the manufac-  
turer's ꢀtting instructions.  
tions; the maximum permissible speed for  
your vehicle may be signiꢀcantly lower. The  
maximum speed limit for these tyres depends  
directly on the maximum axle weights for your  
●
car and on the listed weight rating of the tyres  
being used.  
Keep your speed below 50 km/h (30 mph).  
Winter tyres lose a great deal of their proper-  
ties when the tread is worn down to a depth of  
4 mm.  
Snow chains will improve braking ability as well  
as traction in winter conditions.  
It is best to contact a specialised CUPRA Serv-  
ice or SEAT Oꢁicial Service to check the max-  
imum speed which is permissible for the V-  
rated tyres ꢀtted on your car on the basis of  
this information.  
The performance of winter tyres is also se-  
verely impaired by ageing, even if the tread is  
still much deeper than 4 mm.  
For technical reasons, the use of snow chains  
is only permitted on the following rim and tyre  
combinations:  
1)  
COC = certiꢀcate of conformity.  
301  
Wheels and tyres  
WARNING  
Preliminary actions  
Tyres  
Wheel rim  
Chains  
●
Stop the vehicle on a level surface and in a  
The use of unsuitable or incorrectly ꢀtted  
chains could lead to serious accidents and  
damage.  
215/55 R 18  
7.5Jx18 ET50  
safe place, as far away from road traꢁic as pos-  
sible.  
215/50 R 19 7.5Jx19 ET50  
Max. link 9  
mm  
7.5Jx20 ET44  
215/45 R 20  
●
●
●
Apply the electronic parking brake.  
Switch oꢁ the drive system and ignition.  
Switch on the hazard warning lights.  
●
●
Always the appropriate snow chains.  
7.5J-Nx20 ET44  
Observe the ꢀtting instructions provided  
by the snow chain manufacturer.  
Other dimensions do not allow chains  
●
Never exceed the maximum permitted  
●
Lay out the on-board tools ››› page 269 and  
speeds when driving with snow chains.  
the wheel to be changed.  
Remove any central wheel trims before ꢀtting  
snow chains.  
●
Follow the legal provisions of each country  
NOTICE  
(reꢂective vest, warning triangles, light beacon,  
etc.).  
Use of snow chains with the emergency  
wheel or inꢂatable spare wheel installed  
●
Remove the snow chains to drive on roads  
●
Get all occupants out of the vehicle and  
without snow. Otherwise they will impair ve-  
hicle handling, damage the tyres and wear  
out very quickly.  
keep them out of the danger zone (e.g. behind  
the guard rail).  
For technical reasons, the use of snow chains  
on the emergency wheel and the inꢂatable  
spare wheel is not permitted.  
●
Wheel rims may be damaged or scratched  
if the chains come into direct contact with  
them. CUPRA recommends the use of coated  
snow chains.  
WARNING  
●
If a rear wheel fails, ꢀt the emergency wheel  
●
Always observe the above steps and pro-  
or inꢂatable spare wheel on the front axle.  
tect yourself and other road users.  
●
Switch the damaged rear wheel with the  
●
If you change the wheel on a slope, block  
wheel on the front axle that is left free. When  
doing so, take into account the tyre rotation  
direction.  
the wheel on the opposite side of the car  
with a stone or similar to prevent the vehicle  
from moving.  
Changing a wheel  
Introduction  
CUPRA recommends ꢀtting the chains to the  
wheel before installing the wheel.  
Only change a wheel yourself if you are famil-  
iar with the necessary operations and safety  
measures, if you have the necessary tools and  
if the vehicle is parked safely.  
302  
Changingawheel  
Wheel bolt caps  
Anti-theft wheel nuts  
Note  
Make a note of the code number of the anti-  
theft wheel bolt and keep it in a safe place,  
but not in your vehicle. If you need a new  
adapter, you can obtain it from the special-  
ised CUPRA service or the SEAT Oꢁicial Serv-  
ice, indicating the code number.  
Loosening wheel nuts  
Fig. 198 Wheel: wheel bolts with caps.  
Fig. 199 Anti-theft wheel bolt with cap  
and adapter.  
Removal  
Loosening the anti-theft wheel bolt  
●
Fit the plastic clip (vehicle tools ››› Fig. 177)  
●
●
Remove the wheel trim or hub cap.  
over the cap until it clicks into place  
››› Fig. 198.  
●
1
Insert the special adapter ››› Fig. 199  
Remove the cap with the plastic clip.  
(vehicle tools ››› page 269) onto the anti-  
theft wheel bolt and push it on as far as it will  
go.  
The caps protect the wheel bolts and should  
be remounted after changing the tyre.  
Fig. 200 Tyre change: slacken the wheel  
bolts.  
●
Insert the wheel brace (vehicle tools) onto  
The anti-theft wheel locking bolt has a spe-  
cial cap. This only ꢀts on anti-theft locking  
bolts and is not for use with standard wheel  
bolts.  
the adapter as far as it will go.  
Use only the wheel wrench belonging to the  
car to loosen the wheel bolts.  
●
Remove the wheel bolt ››› page 303.  
Loosen the wheel bolts only about one turn  
before raising the vehicle with the jack.  
If the wheel bolt is very tight, carefully push on  
the end of the wheel wrench with your foot.  
Hold on to the vehicle for support and take  
care not to slip during this operation.  
303  
Wheels and tyres  
Loosening wheel nuts  
●
To loosen and tighten wheel bolts, only  
use the wheel wrench that came with the car  
from the factory.  
●
Fit the box spanner into the bolt as far as it  
will go ››› Fig. 200.  
●
The wheel bolts should only be loosened  
●
Hold the wrench at the end and rotate  
slightly (about one turn) before raising the  
vehicle with the jack. Risk of accident!  
the bolt approximately one turn anticlock-  
wise ›››  
.
●
Never apply grease or oil to wheel bolts or  
to the wheel hub threads. Even if the bolts  
have been tightened to the prescribed tor-  
que, they could come loose while driving.  
Important information about wheel bolts  
Factory-ꢀtted rims and wheel bolts are spe-  
cially matched during construction. Therefore,  
if diꢁerent rims are ꢀtted, the correct wheel  
bolts with the right length and heads must  
be used. This ensures that wheels are ꢀtted  
securely and that the brake system functions  
correctly.  
●
Never loosen the screwed joints of wheel  
Fig. 202 Crossbar: mounting the jack on  
the vehicle.  
rims with bolted ring trims.  
●
If wheel bolts are tightened below the  
prescribed torque, the bolts and rims could  
come loose while driving. If tightening torque  
is too high, the wheel bolts or threads can be  
damaged.  
●
Rest the jack (vehicles tools) on ꢀrm ground.  
If necessary use a large, strong board or similar  
support. If the surface is slippery (for example  
tiles) place the jack on a rubber mat or similar  
In certain circumstances, you should not even  
use wheel bolts from vehicles of the same  
model.  
to prevent it from slipping ›››  
.
●
Look on the strut for the mark of the jack  
Raise the vehicle  
support point (sunken area) closest to the  
wheel to be changed ››› Fig. 201.  
WARNING  
●
Turn the jack crank handle, located below  
If the wheel bolts are not properly tightened,  
they could come loose while driving and  
cause an accident, serious injury and loss of  
vehicle control.  
the strut support point, to raise it until the  
1
tab  
››› Fig. 202 is below the housing that  
is provided.  
●
Use only wheel bolts which correspond to  
●
1
Align the jack so that the tab  
“grips”  
the rim in question.  
onto the housing provided on the cross mem-  
2
ber and the mobile base  
ground. The base plate  
is resting on the  
should fall vertically  
●
●
Never use diꢁerent wheel bolts.  
2
Wheel bolts and threads should be clean,  
1
with respect to the support point  
.
free of oil and grease, and it should be possi-  
ble to screw them easily.  
Fig. 201 Jack position points.  
●
Continue turning the jack until the wheel is  
slightly lifted oꢁ the ground.  
304  
Changingawheel  
NOTICE  
●
Place the spare wheel or temporary spare  
WARNING  
wheel into position.  
●
The factory-supplied jack is only designed  
for changing wheels on this model. On no  
account attempt to use it for lifting heavier  
vehicles or other loads. Risk of injury.  
The vehicle must not be raised on the  
●
Screw in the wheel bolts and tighten them a  
crossbar. Place the jack only at the support  
points provided on the strut and align it. Oth-  
erwise, the vehicle may be damaged.  
little with the wheel wrench.  
●
Use the appropriate adapter to tighten the  
anti-theft wheel bolts.  
●
Any type of load or weight applied to the  
●
Make sure the jack remains stable. If the  
external trim/door will (stepped on, ꢀtting  
the jack, resting heavy objects, etc.) can  
cause damage to it. CUPRA accepts no re-  
sponsibility for any damages caused by im-  
proper use of the external trim or body.  
surface is slippery or soft, the jack could slip  
or sink, respectively, with the consequent  
risk of causing injuries.  
●
●
Carefully lower the vehicle using the jack.  
Use the wheel spanner to tighten all of the  
wheel nuts clockwise. Tighten the bolts in di-  
agonal pairs (not in a circle).  
●
Lift the vehicle using only the jack supplied  
from the factory. Other jacks, even those ap-  
proved for other CUPRA models could slip,  
with the consequent risk of injury.  
●
Put the caps, trim or full hubcap back on.  
The wheel bolts should be clean and turn  
easily. Before ꢀtting the spare wheel, inspect  
the wheel condition and hub mounting surfa-  
ces. These surfaces must be clean before ꢀt-  
ting the wheel.  
Removing and installing a wheel  
●
Place the jack only at the support points  
provided on the strut and align it. Otherwise,  
the jack could slip because it does not have  
suꢁicient grip on the vehicle: risk of injury!  
Change the wheel after loosening the wheel  
bolts and raising the vehicle with the jack.  
When removing/ꢀtting the wheel, the rim may  
hit and damage the brake disc. For this reason,  
please take care and get a second person to  
assist you.  
●
You should never place a body limb such as  
Tightening torque of the wheel nuts  
an arm or leg under a raised vehicle that is  
solely supported by the jack.  
The prescribed tightening torque for wheel  
bolts for steel and alloy wheels is 120 Nm. After  
changing a wheel, have the tightening torque  
checked immediately with a torque wrench  
that is working perfectly.  
●
If you have to work underneath the vehi-  
cle, you must use suitable stands additionally  
to support the vehicle, there is a risk of acci-  
dent!.  
Taking oꢁ the wheel  
●
Unscrew the bolts with the wheel wrench  
and place them on a clean surface.  
●
Do not raise the vehicle if it is tilting to one  
side or the drive system is switched on.  
●
Remove the wheel.  
Before checking tightening torque, have any  
rusty wheel bolts that are diꢁicult to screw re-  
placed and clean the wheel hub threads.  
●
Do not switch on the drive system while the  
vehicle is raised. The vehicle may come loose  
from the jack due to the vibrations.  
Putting on the spare wheel  
Never apply grease or oil to wheel bolts or to  
the wheel hub threads. Even if the bolts have  
been tightened to the prescribed torque, they  
could come loose while driving.  
Check the direction of rotation of the tyre  
››› page 306.  
305  
Wheels and tyres  
●
Have the tightening torque of the wheel nuts  
ment panel through a warning lamp and a  
Tyres with directional tread pattern  
checked as soon as possible with a torque  
wrench ››› page 305. Meanwhile, drive care-  
fully.  
warning to the driver ››› Fig. 203. When only  
one speciꢀc tyre is aꢁected, its position within  
the vehicle will be indicated.  
Tyres with directional tread pattern have been  
designed to operate best when rotating in only  
one direction. An arrow on the tyre sidewall  
indicates the direction of rotation on tyres with  
directional tread. Always observe the indicated  
direction of rotation in order to guarantee op-  
timum grip and help avoid aquaplaning, exces-  
sive noise and wear.  
●
sible.  
Have the ꢂat tyre replaced as quickly as pos-  
Loss of pressure: Check left tyre  
pressure!  
Wheel tread change  
Tyre pressure monitor sys-  
tem  
The wheel diameter changes when:  
If the tyre is mounted in the opposite direction  
of rotation, drive with extreme caution, as the  
tyre is no longer being used correctly. This is of  
particular importance when the road surface is  
wet. Change the tyre as soon as possible or re-  
mount it with the correct direction of rotation.  
●
●
●
●
●
Tyre pressure is changed manually.  
Tyre pressure is insuꢁicient.  
Tyre pressure monitor indicator  
The tyre structure is damaged.  
The vehicle is unbalanced because of a load.  
The wheels on an axle are subject to a heav-  
ier load (e.g. with a heavy load).  
●
●
●
The vehicle is ꢀtted with snow chains.  
The temporary spare wheel is ꢀtted.  
The wheel on one axle is changed.  
Works after changing a wheel  
●
Replace the hub caps or wheel bolt caps (de-  
pending on equipment).  
There may be a delay in the reaction of the tyre  
pressure monitoring indicator or it may not  
indicate anything under certain circumstances  
(e.g. sporty driving, snow-covered or unpaved  
roads, or when driving with snow chains).  
●
tion.  
Return all tools to their proper storing loca-  
●
If the replaced wheel does not ꢀt in the spare  
Fig. 203 Instrument panel: warning of loss  
of tyre pressure.  
wheel housing, store it safely in the luggage  
compartment ››› page 263.  
●
Check the tyre pressure of the newly moun-  
The tyre pressure monitoring system compares  
the individual speeds of each wheel and thus  
the dynamic radius with the help of the ABS  
sensors.  
ted tyre as soon as possible.  
●
In vehicles ꢀtted with a tyre pressure indica-  
tor, adjust the pressure and store it in memory  
››› page 306.  
If the rolling circumference of one or more  
wheels has changed, the tyre pressure moni-  
toring indicator will indicate this on the instru-  
306  
Tyre pressuremonitor system  
WARNING  
●
Driving on unpaved roads for a long pe-  
Calibrate the tyre pressure monitoring indi-  
cator  
riod of time, or sporty driving, may tempora-  
rily deactivate the system. The control lamp  
shows a fault, but disappears when road con-  
ditions or the driving style change.  
When the tyres are inꢂated at diꢁerent pres-  
sures or at a pressure that is too low then a  
tyre may be damaged resulting in a loss of  
control of the vehicle and a serious or fatal  
accident.  
After changing the tyre pressure or replacing  
one or more wheels, the tyre pressure moni-  
toring indicator must be recalibrated. Do the  
same, for example, when the front and rear  
wheels are swapped.  
●
Do not only rely on the tyre pressure moni-  
toring system. Regularly check your tyres to  
ensure that the tyre pressure is correct and  
that the tyres are not damaged due to punc-  
ture, cuts, tears and impacts/dents. Remove  
objects from the tyres only when they have  
not pierced the tyres.  
●
If the lamp lights up, reduce speed im-  
mediately and avoid any sudden turning or  
braking manoeuvres. Stop when possible,  
and check the tyre pressure and status.  
It should be calibrated with the vehicle stop-  
ped and its tyres cold. If calibrated while the  
tyres are hot, the pressure check and calibra-  
tion procedure should be repeated when cold  
before the next trip.  
●
The tyre pressure loss indicator only works  
correctly if all the tyres are at the correct  
pressure when cold, and it is subsequently  
calibrated according to the described proce-  
dure.  
●
The tyre pressure monitoring indicator  
does not function when there is a fault in the  
●
●
Switch the ignition on.  
ESC or ABS ››› page 152.  
Memorise the new inꢂation pressure in the  
Infotainment system: function button  
>
●
If a tyre has not been punctured and it does  
Vehicle info > Vehicle status ››› page 34.  
Troubleshooting  
not have to be changed immediately, drive to  
the nearest specialised workshop at a mod-  
erate speed and have the tyre checked and  
inꢂated to the correct pressure.  
●
OR: through the Servicemenu on the in-  
Low tyre pressure  
strument cluster ››› page 30.  
The control lamp switches on yellow.  
The tyre pressure loss indicator uses the ABS  
sensors to compare the turns of each wheel  
and, therefore, their tread circumferences,  
among other aspects. After a long journey with  
varied speeds the programmed values are col-  
lected and monitored.  
The inꢂation pressure of one or more wheels  
is much lower than the value set by the driver,  
or the tyre has structural damage. In addition,  
a audible warning sounds and a text message is  
displayed on the instrument panel screen.  
Note  
●
Driving for the ꢀrst time with new tyres at  
a high speed can cause them to slightly ex-  
pand, which could then produce an air pres-  
sure warning.  
With the wheels under very heavy loads, the  
tyre pressure must be increased to the total  
recommended tyre pressure before the cali-  
bration ››› Fig. 203.  
●
Stop the vehicle! Stop the vehicle safely  
●
If excessively low tyre pressure is detected  
as soon as possible.  
with the ignition on, an audible warning will  
sound. In the event that there is a fault in the  
system, an audible warning will sound.  
●
●
Check all tyres and pressures.  
Replace any damaged tyres.  
307  
Wheels and tyres  
Do not use the tyre sealant in the following  
cases:  
●
Use the tyre mobility system only if you  
Fault in the tyre pressure loss indicator  
are familiar with the necessary procedures.  
Otherwise, you should seek professional as-  
sistance.  
The control lamp ꢂashes for approximately 1  
minute and then lights up permanently in yel-  
low.  
●
●
●
If the wheel rim has been damaged.  
In outside temperatures below -20°C (-4°F).  
In the event of cuts or perforations in the tyre  
●
The tyre mobility set is intended for tem-  
●
If the tyre is inꢂated correctly, switch the ig-  
nition oꢁ and on again.  
porary emergency use only until you can  
reach the nearest specialised workshop.  
greater than 4 mm.  
●
●
Re-calibrate the tyre pressure monitoring  
Replace the repaired tyre with the tyre mo-  
●
If you have been driving with very low pres-  
bility set as soon as possible.  
system ››› page 306  
●
sure or a completely ꢂat tyre.  
●
The sealant is a health hazard and must be  
●
date.  
If the fault continues, go to a specialised  
If the sealant bottle has passed its use by  
cleaned immediately if it comes into contact  
with the skin.  
workshop.  
●
Always keep the tyre mobility set out of the  
WARNING  
reach of small children.  
Tyre repair  
Using the puncture repair kit can be danger-  
ous, particularly when ꢀlling the tyre on the  
roadside. To reduce the risk of serious injury,  
consider the following:  
TMS (Tyre Mobility System) punc-  
ture repair kit  
WARNING  
A tyre ꢀlled with sealant does not have the  
same performance properties as a conven-  
tional tyre.  
●
Stop the vehicle safely as soon as possible.  
The puncture repair kit (Tyre Mobility System)  
will reliably seal punctures caused by the pene-  
tration of a foreign body of up to about 4 mm  
in diameter. Do not remove foreign objects,  
e.g. screws or nails, from the tyre.  
Park it at a safe distance from surrounding  
traꢁic to ꢀll the tyre.  
●
●
Never drive faster than 80 km/h (50 mph).  
Avoid heavy acceleration, hard braking and  
●
Ensure the ground on which you park is ꢂat  
and solid.  
fast cornering.  
●
All passengers and particularly children  
●
Drive for only 10 minutes at a maximum  
After inserting the sealant residue in the tyre,  
you must again check the tyre pressure about  
10 minutes after starting the engine.  
must keep a safe distance from the work  
area.  
speed of 80 km/h (50 mph) and then check  
the tyre.  
●
Turn on the hazard warning lights to warn  
You should only use the tyre mobility set if the  
vehicle is parked in a safe place, you are famil-  
iar with the procedure and you have the nec-  
essary tyre mobility set. Otherwise, you should  
seek professional assistance.  
other road users.  
For the sake of the environment  
●
Apply the electronic parking brake and  
Dispose of used or expired sealant observing  
any legal requirements.  
switch oꢁ the drive system.  
308  
Tyrerepair
1
2
●
Valve insert remover  
Shake the tyre sealant bottle vigorously  
Note  
10  
››› Fig. 204  
.
A sticker to be adhered to the instrument  
cluster, within the driver's visual ꢀeld, to  
remind that the maximum advisable speed  
“max. 80 km/h” or “max. 50 mph”  
You can purchase a new bottle of tyre seal-  
ant in specialised CUPRA dealers or any SEAT  
dealership.  
●
3
Screw the tyre inꢂation hose ››› Fig. 204  
into the tyre sealant bottle. The bottle's seal  
will break automatically.  
3
Filler tube with cap  
●
3
Remove the ꢀller cap ››› Fig. 204  
and  
Note  
screw the open end of the tube into the tyre  
valve.  
4
Air compressor (depending on the version,  
the model may vary).  
Take into account the separate instruction  
manual provided by the tyre mobility system  
manufacturer.  
●
With the bottle upside down, empty all of  
5
ON/OFF switch  
the contents into the tyre.  
6
Air bleed screw (it can also be integrated in  
the inꢂator tube).  
●
●
Remove the bottle from the valve.  
Anti-puncture kit contents  
Replace the howitzer with the device  
7
Warning provided by tyre pressure moni-  
toring system (it can also be integrated in  
the inꢂator tube).  
1
››› Fig. 204 onto the tyre valve.  
Inꢂating the tyre  
8
Tube for inꢂating tyres  
12 volt connector  
Bottle of sealant  
Spare tyre valve  
●
Screw the tyre inꢂation tube of the compres-  
9
8
sor ››› Fig. 204  
on the tyre valve.  
10  
●
Check that the air evacuation screw is  
11  
6
closed ››› Fig. 204  
.
1
The valve insert remover  
lower end for a valve insert. The valve insert  
can only be screwed or unscrewed in this way.  
This also applies to its replacement part  
has a gap at the  
●
Connect the drive system.  
●
9
Attach the connector ››› Fig. 204  
to the  
11  
vehicle’s 12 volt power outlet ››› page 213.  
●
.
Switch on the air compressor with ON/OFF  
5
switch ››› Fig. 204  
.
Fig. 204 Standard display: contents of the  
anti-puncture kit.  
Sealing and inꢂating a tyre  
●
Keep the air compressor running until it  
reaches a pressure of 2.0-2.5 bar (29-36 psi/  
Sealing the tyre  
The anti-puncture kit is located underneath  
the ꢂoor covering in the luggage compart-  
ment. Includes the following components  
››› Fig. 204:  
200-250 kPa). A maximum of 8 minutes.  
●
Unscrew the tyre valve cap and insert. Use  
●
●
1
Disconnect the air compressor.  
the device ››› Fig. 204  
to remove the valve  
cap. Place it on a clean surface.  
If it does not reach the pressure indicated,  
unscrew the tyre inꢂator tube from the valve.  
309  
Wheels and tyres  
●
Move the vehicle 10m so that the sealant is  
●
If it is not possible to inꢂate the tyre to at  
WARNING  
distributed throughout the tyre.  
least 2.0 bars (29 psi / 200 kPa), the tyre is  
too badly damaged. The sealant is not in a  
good condition to seal the tyre. Do not con-  
tinue driving. Seek specialist assistance.  
Driving with an unsealed tyre is dangerous  
and can cause accidents and serious injury.  
●
Screw the compressor tyre inꢂator into the  
valve.  
●
Do not continue driving if the tyre pressure  
is 1.3 bar (19 psi / 130 kPa) and lower.  
●
●
Repeat the inꢂation process.  
If it still does not come up to pressure, the  
●
Seek specialist assistance.  
NOTICE  
tyre is too badly damaged. Stop and seek assis-  
tance from authorised personnel.  
Switch oꢁ the air compressor after a maxi-  
mum of 8 operational minutes to avoid over-  
heating! Before switching on the air com-  
pressor again, let it cool for several minutes.  
●
Disconnect the air compressor. Unscrew the  
tyre inꢂation tube from the tyre valve.  
●
When the tyre pressure is between 2.5 and  
2.0 bars, continue driving without exceeding  
80 km/h (50 mph).  
Check after 10 minutes of driving  
●
2
Attach the sticker ››› Fig. 204  
to the in-  
8
Screw in the inꢂator tube ››› Fig. 204  
and check the pressure on the gauge  
again  
strument panel display, within the driver's ꢀeld  
of vision.  
7
.
●
Check the pressure again after 10 minutes  
1.3 bar (19 psi / 130 kPa) and lower:  
››› page 310.  
●
Stop the vehicle! The tyre cannot be sealed  
suꢁiciently with the tyre mobility set.  
WARNING  
●
You should obtain professional assistance  
When inꢂating the wheel, the air compressor  
and the inꢂator tube may become hot.  
›››  
.
●
●
Protect hands and skin from hot parts.  
Do not place the hot ꢂexible inꢂator tube  
1.4 bar (20 psi/140 kPa) and higher:  
●
Set the tyre pressure to the correct value  
or hot air compressor on ꢂammable material.  
again.  
●
vice.  
Allow them to cool before storing the de-  
●
Carefully resume your journey until you  
reach the nearest specialised workshop with-  
out exceeding 80 km/h (50 mph).  
●
Have the damaged tyre replaced.  
310  

Related Topics

Popular Owner Manuals