2002-2008 Cupra Born SUV Wheels and tyres -> Changing a wheel User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Wheels and tyres -> Changing a wheel for Your Cupra Born SUV First Generation (2002-2008)

Wheels and tyres  
WARNING  
Preliminary actions  
Tyres  
Wheel rim  
Chains  
●
Stop the vehicle on a level surface and in a  
The use of unsuitable or incorrectly ꢁtted  
chains could lead to serious accidents and  
damage.  
215/55 R 18  
7.5Jx18 ET50  
safe place, as far away from road traꢂic as pos-  
sible.  
215/50 R 19 7.5Jx19 ET50  
Max. link 9  
mm  
7.5Jx20 ET44  
215/45 R 20  
●
●
●
Apply the electronic parking brake.  
Switch oꢂ the drive system and ignition.  
Switch on the hazard warning lights.  
●
●
Always the appropriate snow chains.  
7.5J-Nx20 ET44  
Observe the ꢁtting instructions provided  
by the snow chain manufacturer.  
Other dimensions do not allow chains  
●
Never exceed the maximum permitted  
●
Lay out the on-board tools ››› page 269 and  
speeds when driving with snow chains.  
the wheel to be changed.  
Remove any central wheel trims before ꢀtting  
snow chains.  
●
Follow the legal provisions of each country  
NOTICE  
(reꢁective vest, warning triangles, light beacon,  
etc.).  
Use of snow chains with the emergency  
wheel or inꢀatable spare wheel installed  
●
Remove the snow chains to drive on roads  
●
Get all occupants out of the vehicle and  
without snow. Otherwise they will impair ve-  
hicle handling, damage the tyres and wear  
out very quickly.  
keep them out of the danger zone (e.g. behind  
the guard rail).  
For technical reasons, the use of snow chains  
on the emergency wheel and the inꢁatable  
spare wheel is not permitted.  
●
Wheel rims may be damaged or scratched  
if the chains come into direct contact with  
them. CUPRA recommends the use of coated  
snow chains.  
WARNING  
●
If a rear wheel fails, ꢀt the emergency wheel  
●
Always observe the above steps and pro-  
or inꢁatable spare wheel on the front axle.  
tect yourself and other road users.  
●
Switch the damaged rear wheel with the  
●
If you change the wheel on a slope, block  
wheel on the front axle that is left free. When  
doing so, take into account the tyre rotation  
direction.  
the wheel on the opposite side of the car  
with a stone or similar to prevent the vehicle  
from moving.  
Changing a wheel  
Introduction  
CUPRA recommends ꢀtting the chains to the  
wheel before installing the wheel.  
Only change a wheel yourself if you are famil-  
iar with the necessary operations and safety  
measures, if you have the necessary tools and  
if the vehicle is parked safely.  
302  
Changingawheel  
Wheel bolt caps  
Anti-theft wheel nuts  
Note  
Make a note of the code number of the anti-  
theft wheel bolt and keep it in a safe place,  
but not in your vehicle. If you need a new  
adapter, you can obtain it from the special-  
ised CUPRA service or the SEAT Oꢂicial Serv-  
ice, indicating the code number.  
Loosening wheel nuts  
Fig. 198 Wheel: wheel bolts with caps.  
Fig. 199 Anti-theft wheel bolt with cap  
and adapter.  
Removal  
Loosening the anti-theft wheel bolt  
●
Fit the plastic clip (vehicle tools ››› Fig. 177)  
●
●
Remove the wheel trim or hub cap.  
over the cap until it clicks into place  
››› Fig. 198.  
●
1
Insert the special adapter ››› Fig. 199  
Remove the cap with the plastic clip.  
(vehicle tools ››› page 269) onto the anti-  
theft wheel bolt and push it on as far as it will  
go.  
The caps protect the wheel bolts and should  
be remounted after changing the tyre.  
Fig. 200 Tyre change: slacken the wheel  
bolts.  
●
Insert the wheel brace (vehicle tools) onto  
The anti-theft wheel locking bolt has a spe-  
cial cap. This only ꢀts on anti-theft locking  
bolts and is not for use with standard wheel  
bolts.  
the adapter as far as it will go.  
Use only the wheel wrench belonging to the  
car to loosen the wheel bolts.  
●
Remove the wheel bolt ››› page 303.  
Loosen the wheel bolts only about one turn  
before raising the vehicle with the jack.  
If the wheel bolt is very tight, carefully push on  
the end of the wheel wrench with your foot.  
Hold on to the vehicle for support and take  
care not to slip during this operation.  
303  
Wheels and tyres  
Loosening wheel nuts  
●
To loosen and tighten wheel bolts, only  
use the wheel wrench that came with the car  
from the factory.  
●
Fit the box spanner into the bolt as far as it  
will go ››› Fig. 200.  
●
The wheel bolts should only be loosened  
●
Hold the wrench at the end and rotate  
slightly (about one turn) before raising the  
vehicle with the jack. Risk of accident!  
the bolt approximately one turn anticlock-  
wise ›››  
.
●
Never apply grease or oil to wheel bolts or  
to the wheel hub threads. Even if the bolts  
have been tightened to the prescribed tor-  
que, they could come loose while driving.  
Important information about wheel bolts  
Factory-ꢀtted rims and wheel bolts are spe-  
cially matched during construction. Therefore,  
if diꢂerent rims are ꢀtted, the correct wheel  
bolts with the right length and heads must  
be used. This ensures that wheels are ꢀtted  
securely and that the brake system functions  
correctly.  
●
Never loosen the screwed joints of wheel  
Fig. 202 Crossbar: mounting the jack on  
the vehicle.  
rims with bolted ring trims.  
●
If wheel bolts are tightened below the  
prescribed torque, the bolts and rims could  
come loose while driving. If tightening torque  
is too high, the wheel bolts or threads can be  
damaged.  
●
Rest the jack (vehicles tools) on ꢀrm ground.  
If necessary use a large, strong board or similar  
support. If the surface is slippery (for example  
tiles) place the jack on a rubber mat or similar  
In certain circumstances, you should not even  
use wheel bolts from vehicles of the same  
model.  
to prevent it from slipping ›››  
.
●
Look on the strut for the mark of the jack  
Raise the vehicle  
support point (sunken area) closest to the  
wheel to be changed ››› Fig. 201.  
WARNING  
●
Turn the jack crank handle, located below  
If the wheel bolts are not properly tightened,  
they could come loose while driving and  
cause an accident, serious injury and loss of  
vehicle control.  
the strut support point, to raise it until the  
1
tab  
››› Fig. 202 is below the housing that  
is provided.  
●
Use only wheel bolts which correspond to  
●
1
Align the jack so that the tab  
“grips”  
the rim in question.  
onto the housing provided on the cross mem-  
2
ber and the mobile base  
ground. The base plate  
is resting on the  
should fall vertically  
●
●
Never use diꢂerent wheel bolts.  
2
Wheel bolts and threads should be clean,  
1
with respect to the support point  
.
free of oil and grease, and it should be possi-  
ble to screw them easily.  
Fig. 201 Jack position points.  
●
Continue turning the jack until the wheel is  
slightly lifted oꢂ the ground.  
304  
Changingawheel  
NOTICE  
●
Place the spare wheel or temporary spare  
WARNING  
wheel into position.  
●
The factory-supplied jack is only designed  
for changing wheels on this model. On no  
account attempt to use it for lifting heavier  
vehicles or other loads. Risk of injury.  
The vehicle must not be raised on the  
●
Screw in the wheel bolts and tighten them a  
crossbar. Place the jack only at the support  
points provided on the strut and align it. Oth-  
erwise, the vehicle may be damaged.  
little with the wheel wrench.  
●
Use the appropriate adapter to tighten the  
anti-theft wheel bolts.  
●
Any type of load or weight applied to the  
●
Make sure the jack remains stable. If the  
external trim/door will (stepped on, ꢁtting  
the jack, resting heavy objects, etc.) can  
cause damage to it. CUPRA accepts no re-  
sponsibility for any damages caused by im-  
proper use of the external trim or body.  
surface is slippery or soft, the jack could slip  
or sink, respectively, with the consequent  
risk of causing injuries.  
●
●
Carefully lower the vehicle using the jack.  
Use the wheel spanner to tighten all of the  
wheel nuts clockwise. Tighten the bolts in di-  
agonal pairs (not in a circle).  
●
Lift the vehicle using only the jack supplied  
from the factory. Other jacks, even those ap-  
proved for other CUPRA models could slip,  
with the consequent risk of injury.  
●
Put the caps, trim or full hubcap back on.  
The wheel bolts should be clean and turn  
easily. Before ꢀtting the spare wheel, inspect  
the wheel condition and hub mounting surfa-  
ces. These surfaces must be clean before ꢀt-  
ting the wheel.  
Removing and installing a wheel  
●
Place the jack only at the support points  
provided on the strut and align it. Otherwise,  
the jack could slip because it does not have  
suꢂicient grip on the vehicle: risk of injury!  
Change the wheel after loosening the wheel  
bolts and raising the vehicle with the jack.  
When removing/ꢀtting the wheel, the rim may  
hit and damage the brake disc. For this reason,  
please take care and get a second person to  
assist you.  
●
You should never place a body limb such as  
Tightening torque of the wheel nuts  
an arm or leg under a raised vehicle that is  
solely supported by the jack.  
The prescribed tightening torque for wheel  
bolts for steel and alloy wheels is 120 Nm. After  
changing a wheel, have the tightening torque  
checked immediately with a torque wrench  
that is working perfectly.  
●
If you have to work underneath the vehi-  
cle, you must use suitable stands additionally  
to support the vehicle, there is a risk of acci-  
dent!.  
Taking oꢂ the wheel  
●
Unscrew the bolts with the wheel wrench  
and place them on a clean surface.  
●
Do not raise the vehicle if it is tilting to one  
side or the drive system is switched on.  
●
Remove the wheel.  
Before checking tightening torque, have any  
rusty wheel bolts that are diꢂicult to screw re-  
placed and clean the wheel hub threads.  
●
Do not switch on the drive system while the  
vehicle is raised. The vehicle may come loose  
from the jack due to the vibrations.  
Putting on the spare wheel  
Never apply grease or oil to wheel bolts or to  
the wheel hub threads. Even if the bolts have  
been tightened to the prescribed torque, they  
could come loose while driving.  
Check the direction of rotation of the tyre  
››› page 306.  
305  

Related Topics

Popular Owner Manuals