2002-2008 Cupra Born SUV Wheels and tyres -> Tyre repair User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Wheels and tyres -> Tyre repair for Your Cupra Born SUV First Generation (2002-2008)

Wheels and tyres  
Do not use the tyre sealant in the following  
cases:  
●
Use the tyre mobility system only if you  
Fault in the tyre pressure loss indicator  
are familiar with the necessary procedures.  
Otherwise, you should seek professional as-  
sistance.  
The control lamp ꢀashes for approximately 1  
minute and then lights up permanently in yel-  
low.  
●
●
●
If the wheel rim has been damaged.  
In outside temperatures below -20°C (-4°F).  
In the event of cuts or perforations in the tyre  
●
The tyre mobility set is intended for tem-  
●
If the tyre is inꢀated correctly, switch the ig-  
nition oꢁ and on again.  
porary emergency use only until you can  
reach the nearest specialised workshop.  
greater than 4 mm.  
●
●
Re-calibrate the tyre pressure monitoring  
Replace the repaired tyre with the tyre mo-  
●
If you have been driving with very low pres-  
bility set as soon as possible.  
system ››› page 306  
●
sure or a completely ꢀat tyre.  
●
The sealant is a health hazard and must be  
●
date.  
If the fault continues, go to a specialised  
If the sealant bottle has passed its use by  
cleaned immediately if it comes into contact  
with the skin.  
workshop.  
●
Always keep the tyre mobility set out of the  
WARNING  
reach of small children.  
Tyre repair  
Using the puncture repair kit can be danger-  
ous, particularly when ꢀlling the tyre on the  
roadside. To reduce the risk of serious injury,  
consider the following:  
TMS (Tyre Mobility System) punc-  
ture repair kit  
WARNING  
A tyre ꢀlled with sealant does not have the  
same performance properties as a conven-  
tional tyre.  
●
Stop the vehicle safely as soon as possible.  
The puncture repair kit (Tyre Mobility System)  
will reliably seal punctures caused by the pene-  
tration of a foreign body of up to about 4 mm  
in diameter. Do not remove foreign objects,  
e.g. screws or nails, from the tyre.  
Park it at a safe distance from surrounding  
traꢁic to ꢀll the tyre.  
●
●
Never drive faster than 80 km/h (50 mph).  
Avoid heavy acceleration, hard braking and  
●
Ensure the ground on which you park is ꢂat  
and solid.  
fast cornering.  
●
All passengers and particularly children  
●
Drive for only 10 minutes at a maximum  
After inserting the sealant residue in the tyre,  
you must again check the tyre pressure about  
10 minutes after starting the engine.  
must keep a safe distance from the work  
area.  
speed of 80 km/h (50 mph) and then check  
the tyre.  
●
Turn on the hazard warning lights to warn  
You should only use the tyre mobility set if the  
vehicle is parked in a safe place, you are famil-  
iar with the procedure and you have the nec-  
essary tyre mobility set. Otherwise, you should  
seek professional assistance.  
other road users.  
For the sake of the environment  
●
Apply the electronic parking brake and  
Dispose of used or expired sealant observing  
any legal requirements.  
switch oꢁ the drive system.  
308  
Tyrerepair
1
2
●
Valve insert remover  
Shake the tyre sealant bottle vigorously  
Note  
10  
››› Fig. 204  
.
A sticker to be adhered to the instrument  
cluster, within the driver's visual ꢂeld, to  
remind that the maximum advisable speed  
“max. 80 km/h” or “max. 50 mph”  
You can purchase a new bottle of tyre seal-  
ant in specialised CUPRA dealers or any SEAT  
dealership.  
●
3
Screw the tyre inꢀation hose ››› Fig. 204  
into the tyre sealant bottle. The bottle's seal  
will break automatically.  
3
Filler tube with cap  
●
3
Remove the ꢂller cap ››› Fig. 204  
and  
Note  
screw the open end of the tube into the tyre  
valve.  
4
Air compressor (depending on the version,  
the model may vary).  
Take into account the separate instruction  
manual provided by the tyre mobility system  
manufacturer.  
●
With the bottle upside down, empty all of  
5
ON/OFF switch  
the contents into the tyre.  
6
Air bleed screw (it can also be integrated in  
the inꢀator tube).  
●
●
Remove the bottle from the valve.  
Anti-puncture kit contents  
Replace the howitzer with the device  
7
Warning provided by tyre pressure moni-  
toring system (it can also be integrated in  
the inꢀator tube).  
1
››› Fig. 204 onto the tyre valve.  
Inꢂating the tyre  
8
Tube for inꢀating tyres  
12 volt connector  
Bottle of sealant  
Spare tyre valve  
●
Screw the tyre inꢀation tube of the compres-  
9
8
sor ››› Fig. 204  
on the tyre valve.  
10  
●
Check that the air evacuation screw is  
11  
6
closed ››› Fig. 204  
.
1
The valve insert remover  
lower end for a valve insert. The valve insert  
can only be screwed or unscrewed in this way.  
This also applies to its replacement part  
has a gap at the  
●
Connect the drive system.  
●
9
Attach the connector ››› Fig. 204  
to the  
11  
vehicle’s 12 volt power outlet ››› page 213.  
●
.
Switch on the air compressor with ON/OFF  
5
switch ››› Fig. 204  
.
Fig. 204 Standard display: contents of the  
anti-puncture kit.  
Sealing and inꢂating a tyre  
●
Keep the air compressor running until it  
reaches a pressure of 2.0-2.5 bar (29-36 psi/  
Sealing the tyre  
The anti-puncture kit is located underneath  
the ꢀoor covering in the luggage compart-  
ment. Includes the following components  
››› Fig. 204:  
200-250 kPa). A maximum of 8 minutes.  
●
Unscrew the tyre valve cap and insert. Use  
●
●
1
Disconnect the air compressor.  
the device ››› Fig. 204  
to remove the valve  
cap. Place it on a clean surface.  
If it does not reach the pressure indicated,  
unscrew the tyre inꢀator tube from the valve.  
309  
Wheels and tyres  
●
Move the vehicle 10m so that the sealant is  
●
If it is not possible to inꢂate the tyre to at  
WARNING  
distributed throughout the tyre.  
least 2.0 bars (29 psi / 200 kPa), the tyre is  
too badly damaged. The sealant is not in a  
good condition to seal the tyre. Do not con-  
tinue driving. Seek specialist assistance.  
Driving with an unsealed tyre is dangerous  
and can cause accidents and serious injury.  
●
Screw the compressor tyre inꢀator into the  
valve.  
●
Do not continue driving if the tyre pressure  
is 1.3 bar (19 psi / 130 kPa) and lower.  
●
●
Repeat the inꢀation process.  
If it still does not come up to pressure, the  
●
Seek specialist assistance.  
NOTICE  
tyre is too badly damaged. Stop and seek assis-  
tance from authorised personnel.  
Switch oꢁ the air compressor after a maxi-  
mum of 8 operational minutes to avoid over-  
heating! Before switching on the air com-  
pressor again, let it cool for several minutes.  
●
Disconnect the air compressor. Unscrew the  
tyre inꢀation tube from the tyre valve.  
●
When the tyre pressure is between 2.5 and  
2.0 bars, continue driving without exceeding  
80 km/h (50 mph).  
Check after 10 minutes of driving  
●
2
Attach the sticker ››› Fig. 204  
to the in-  
8
Screw in the inꢀator tube ››› Fig. 204  
and check the pressure on the gauge  
again  
strument panel display, within the driver's ꢂeld  
of vision.  
7
.
●
Check the pressure again after 10 minutes  
1.3 bar (19 psi / 130 kPa) and lower:  
››› page 310.  
●
Stop the vehicle! The tyre cannot be sealed  
suꢁiciently with the tyre mobility set.  
WARNING  
●
You should obtain professional assistance  
When inꢂating the wheel, the air compressor  
and the inꢂator tube may become hot.  
›››  
.
●
●
Protect hands and skin from hot parts.  
Do not place the hot ꢂexible inꢂator tube  
1.4 bar (20 psi/140 kPa) and higher:  
●
Set the tyre pressure to the correct value  
or hot air compressor on ꢂammable material.  
again.  
●
vice.  
Allow them to cool before storing the de-  
●
Carefully resume your journey until you  
reach the nearest specialised workshop with-  
out exceeding 80 km/h (50 mph).  
●
Have the damaged tyre replaced.  
310  

Related Topics

Popular Owner Manuals