2002-2008 Cupra Born SUV Wheels and tyres -> Important information about wheels and tyres User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Wheels and tyres -> Important information about wheels and tyres for Your Cupra Born SUV First Generation (2002-2008)

Wheels and tyres  
Low proꢀle tyres  
Foreign objects inserted in the tyre  
Wheels and tyres  
●
Low proꢀle tyres have a wider tread, a larger  
wheel diameter and a lower sidewall height.  
Therefore, its driving behaviour is more agile.  
Do not remove foreign bodies if they have  
penetrated through the tyre wall!  
Important information  
about wheels and tyres  
●
If the vehicle comes with a tyre mobility sys-  
tem, where necessary seal the damaged tyre as  
Low proꢀle tyres may deteriorate more quickly  
than standard tyres, for instance due to  
strong knocks, potholes, manhole covers and  
kerbs. Correct tyre pressure is very important  
››› page 298.  
To avoid damage to tyres and wheels, drive  
with special care when driving on roads in poor  
condition.  
shown in section ››› page 308. Use a special-  
ised workshop for repair or replacement. To do  
so, CUPRA recommends going to a specialised  
CUPRA dealer or any SEAT dealership.  
General notes  
●
When driving with new tyres, be especially  
careful during the ꢀrst 600 km (300 miles).  
The sealant at the lower part of the tyre tread  
wraps around the foreign body and provision-  
ally seals the tyre.  
●
If you have to drive over a kerb or similar ob-  
stacle, drive very slowly and as near as possible  
at a right angle to the obstacle.  
Visually check your wheels every 3000 km.  
●
Check from time to time if the tyres are  
Tyres with directional tread pattern  
If the tyres or rims have received a heavy im-  
pact or have been damaged, have a special-  
ised workshop check whether or not it is nec-  
essary to change the tyre.  
damaged (punctures, cuts, cracks or dents).  
Remove any foreign objects embedded in the  
treads.  
An arrow on the tyre sidewall indicates the di-  
rection of rotation on single drive tyres. Always  
note the direction of rotation indicated when  
mounting the wheel. This makes sure that op-  
timal use is made of tyre properties in terms of  
aquaplaning, grip, excessive noise and wear.  
●
Damaged wheels and tyres must be replaced  
Low proꢀle tyres may deteriorate more quickly  
than standard tyres.  
immediately.  
●
●
Keep grease, oil and fuel oꢁ the tyres.  
Replace any missing valve caps as soon as  
Concealed damage  
Subsequent ꢀtting of accessories  
possible.  
Damage to tyres and rims is often not readily  
visible. If you notice unusual vibration or the  
car pulling to one side, this may indicate that  
one of the tyres is damaged. Reduce speed im-  
mediately if there is any reason to suspect that  
damage may have occurred. Inspect the tyres  
for damage. If no external damage is visible,  
drive slowly and carefully to the nearest speci-  
alised workshop and have the car inspected.  
If you wish to change or ꢀt wheels, rims or  
wheel trims, we recommend that you consult  
with a specialised CUPRA Service or SEAT Oꢁi-  
cial Service centre for advice regarding current  
technical recommendations.  
●
Mark the wheels before taking them oꢁ so  
that they rotate in the same direction when put  
back.  
●
When removed, the wheels or tyres should  
be stored in a cool, dry and preferably dark  
place.  
Speed symbols  
The speed rating indicates the maximum  
speed permitted for the tyres.  
296  
Important informationaboutwheels and tyres  
New wheels and tyres  
P
Q
R
S
max. 150 km/h (93 mph)  
max. 160 km/h (99 mph)  
max. 170 km/h (106 mph)  
max. 180 km/h (112 mph)  
max. 190 km/h (118 mph)  
max. 200 km/h (124 mph)  
max. 210 km/h (130 mph)  
max. 240 km/h (149 mph)  
max. 240 km/h (149 mph)  
max. 270 km/h (168 mph)  
max. 300 km/h (186 mph)  
If the type of spare wheel is diꢁerent form  
the normal wheels — e.g. in the case of win-  
ter tyres or particularly wide tyres — the spare  
wheel should only be used temporarily in the  
event of a puncture, and the vehicle should be  
driven with care. Reꢀt the normal road wheel  
as soon as possible.  
It is best to have all wheels and tyres serviced  
by a specialised workshop. There they have the  
required knowledge, the special tools and the  
corresponding spare parts.  
T
●
The vehicle is factory ꢀtted with original  
U
H
V
Z
W
Y
CUPRA tyres with optimised rolling resistance.  
The original CUPRA tyres are marked with the  
symbol . Only with these tyres can the speci-  
ꢀed energy consumption and range be ach-  
ieved. When buying new tyres, always make  
sure they have optimised rolling resistance  
In vehicles with four-wheel drive, the 4 wheels  
must be ꢀtted with tyres of the same brand,  
type and tread so that the traction system is  
not damaged by a diꢁerence in the number of  
turns of the wheels. Therefore, in the event of  
a puncture, only a spare wheel with the same  
perimeter as normal tyres should be used.  
››› page 138.  
●
Even winter tyres lose their grip on ice. If you  
Manufacturing date  
have installed new tyres, drive the ꢀrst 600 km  
carefully and at a moderate speed.  
WARNING  
The manufacturing date is also indicated on  
the tyre sidewall (or on the inside face of the  
wheel):  
●
New tyres do not have maximum grip dur-  
●
All four wheels must be ꢀtted with tyres  
ing the ꢀrst 600 km. Drive particularly care-  
fully to avoid possible accidents.  
of the same type, size (rolling circumference)  
and, if possible, tread pattern.  
DOT ... 2220 ...  
●
Never drive with damaged tyres. This may  
●
When changing tyres, do not change just  
cause an accident.  
it means, for example, that the tyre was manu-  
factured in the 22nd week of 2020.  
one; change at least two on the same axle.  
●
If you notice unusual vibrations or if the  
●
If you want to equip your vehicle with a com-  
vehicle pulls to one side when driving, stop  
the vehicle immediately and check the tyres.  
bination tyres and rims that are diꢁerent to  
those ꢀtted in the factory, inform your special-  
●
Never use old tyres or those with an un-  
ised workshop before purchasing them ›››  
known history of use.  
The sizes of the rims and tyres approved for  
your vehicle are listed in the vehicle documen-  
tation (e.g. EC Certiꢀcate of Conformity or  
COC document1)). The vehicle documentation  
varies depending on the country of residence.  
1)  
COC = certiꢀcate of conformity.  
297  
Wheels and tyres  
Tyre life  
the vehicle when it drives at over 40 km/h. It  
is advisable to remove ice and snow from the  
inside of the wheels using hot water.  
WARNING  
●
Use only combinations of tyres and rims,  
as well as suitable wheel nuts, approved by  
CUPRA. Otherwise the vehicle may be dam-  
aged, causing an accident.  
●
If you drive on dirt or gravel tracks, the  
likelihood of stones becoming trapped inside  
wheel rims with plastic elements increases  
when driving at high speed or in a sporty  
manner. If you see that there are stones trap-  
ped between the aluminium wheel rim and  
the insert, you can attempt to remove them  
using pressurised water.  
●
For technical reasons it is not possible to  
use wheels of other vehicles; in some ca-  
ses not even wheels from the same vehicle  
model should be used.  
●
Always ensure that the tyres you have  
chosen have adequate clearance. When se-  
lecting replacement tyres, do not rely en-  
tirely on the nominal tyre size marked on the  
tyre, since the nominal tyre size can diꢁer  
signiꢀcantly depending on the manufacturer.  
Lack of clearance can damage the tyres or  
the vehicle and, as a result, endanger road  
safety. Accident hazard!  
For the sake of the environment  
Old tyres must be disposed of according to  
the laws in the country concerned.  
Note  
Fig. 195 Location of the tyre pressure  
sticker.  
●
Only use tyres that are over 6 years old in  
●
A CUPRA Service Centre should be consul-  
an emergency, and drive with due care.  
ted to ꢀnd out whether wheels or tyres of  
diꢁerent sizes to those originally ꢀtted by  
CUPRA can be ꢀtted, and to ꢀnd out about  
the combinations allowed between the front  
axle (axle 1) and the rear axle (axle 2).  
●
The ꢀtting of tyres with run-ꢂat properties  
Correct inꢂation pressures and sensible driving  
habits will increase the useful life of your tyres.  
is not permitted on your vehicle! Prohibited  
use can cause accidents or can damage your  
vehicle.  
●
Check tyre pressure at least once a month,  
and also prior to any long trip.  
●
If decorative hubcaps are subsequently ꢀt-  
●
Never mount used tyres if you are not sure  
of their “previous history”.  
●
The tyre pressure should only be checked  
ted, make sure that they allow enough air in  
to cool the braking system. Accident hazard!  
when the tyres are cold. Do not reduce the  
pressure of warm tyres.  
●
Models with aerodynamic wheel rims  
and/or with bolt-on plastic elements (more  
closed design) increase the likelihood of ice  
and snow accumulating on the inside. This  
should be taken into account, depending on  
the driving situations, as snow or ice accu-  
mulated in the wheels can cause vibration in  
●
Adjust tyre pressure to the load being carried  
by the vehicle ››› Fig. 195.  
●
the modiꢀed tyre pressure ››› page 306.  
In vehicles with a tyre pressure indicator, save  
298  
Important informationaboutwheels and tyres  
Wheel balance  
●
●
Avoid fast cornering and hard acceleration.  
Inspect the tyres for irregular wear from time  
●
Tyre pressure should be that indicated on  
the label when the tyres are cold at all times  
The wheels on new vehicles are balanced.  
However, certain circumstances may lead to  
imbalance (run-out), which is detected as vi-  
brations in the steering wheel.  
››› Fig. 195.  
●
of the tyres. If necessary, change the tyre  
pressure of the vehicle tyres while they are  
cold.  
to time.  
Regularly check the cold inꢂation pressure  
Tyre pressure  
The values of the tyre pressure are shown on  
the sticker label located on the read frame of  
the front left door ››› Fig. 195.  
Unbalanced wheels should be rebalanced, as  
they otherwise cause excessive wear on steer-  
ing, suspension and tyres. A wheel must also  
be rebalanced when a new tyre is ꢀtted or if a  
tyre is repaired.  
●
Regularly check your tyres for damage and  
wear.  
Insuꢁicient or excessive pressure greatly re-  
duces the useful life of the tyres and adversely  
aꢁects vehicle performance and ride. Correct  
inꢂation pressures are very important, espe-  
cially at high speeds.  
●
Never exceed the maximum permitted  
speed or loads speciꢀed for the type of tyre  
ꢀtted on your vehicle.  
Incorrect wheel alignment  
Incorrect running gear alignment causes ex-  
cessive tyre wear, impairing the safety of the  
vehicle. If you notice excessive tyre wear, you  
should check wheel alignment at a specialised  
CUPRA Service or SEAT Oꢁicial Service.  
For the sake of the environment  
The tyre pressure must be adjusted according  
to the load the vehicle is carrying. If the vehicle  
is going to be fully loaded, increase the tyre  
pressure to the maximum load value shown on  
Insuꢁicient tyre pressure increases energy  
consumption.  
the sticker label ››› Fig. 195.  
Tread wear indicators  
WARNING  
Do not forget the spare wheel when checking  
the tyre pressures: Keep this spare wheel inꢂa-  
ted to the highest pressure required for the  
road wheels.  
Unsuitable handling of the wheels and tyres  
may lead to sudden tyre pressure losses, to  
tread separation or even to a blow-out.  
●
The driver is responsible for ensuring that  
In the case of a minimised temporary spare  
wheel (125/70 R16 or 125/70 R18) inꢂate to a  
pressure of 4.2 bar as indicated on the tyre  
pressure label ››› Fig. 195.  
all of the vehicle tyres are correctly inꢂa-  
ted to the right pressure. The recommen-  
ded tyre pressure is indicated on the label  
››› Fig. 195.  
●
Check tyre pressures regularly and ensure  
Driving style  
they are maintained at the pressures indica-  
ted. Tyre pressure that is too low could cause  
overheating, resulting in tread detachment  
or even burst tyres.  
Fast cornering, heavy acceleration and hard  
braking (squealing tyres) all increase tyre wear.  
Fig. 196 Tyre proꢀle: tread wear indicators.  
299  
Wheels and tyres  
WARNING  
A special adapter is required to turn the anti-  
theft wheel bolts ››› page 303.  
The tyres must be replaced at the latest when  
the tread is worn down to the tread wear indi-  
cators. Failure to follow this instruction could  
result in an accident.  
Two-piece wheel bolts  
Two-piece wheel bolts must be used for this  
vehicle. In this type of bolt, the spherical collar  
is not ꢀrmly attached to the head.  
●
Particularly in diꢁicult driving conditions  
such as wet or icy roads. It is important that  
the tyre tread be as deep as possible and be  
approximately the same on the tyres of both  
the front and the rear axles.  
WARNING  
Wheel nuts should never be greased or oiled.  
Fig. 197 Interchanging tyres.  
●
The scant driving safety due to insuꢁicient  
●
Use only wheel bolts which belong to the  
tread depth is particularly evident in vehicle  
handling, when there is a risk of “aquaplan-  
ing” in deep puddles of water and when driv-  
ing through corners, and braking is also ad-  
versely aꢁected.  
Wear indicators around 1.6 mm high can be  
found on the base of the original tyre treads,  
ordered at regular intervals and running across  
the tread ››› Fig. 196. The letters “TWI” or  
triangles on the sidewall of the tyre mark the  
position of the wear indicators.  
wheel.  
●
If the prescribed torque of the wheel bolts  
is too low, they could loosen whilst the vehi-  
cle is in motion. Risk of accident! If the tight-  
ening torque is too high, the wheel bolts and  
threads can be damaged.  
●
The speed has to be adapted accordingly,  
otherwise there is a risk of losing control over  
the vehicle.  
The minimum permitted proꢀle depth 1) have  
been reached when the tyres have worn down  
to the wear indicators. Replace the tyres with  
NOTICE  
Wheel nuts  
See ››› page 305 to ꢀnd out the recommen-  
ded tightening torque for wheel nuts for steel  
and alloy rims.  
new ones ›››  
.
The wheel bolts and rims have been designed  
to be part of an assembly. When installing  
diꢁerent wheels (for instance alloy wheels or  
wheels with winter tyres) it is important to use  
the correct wheel bolts with the right length  
and correctly shaped bolt heads. This ensures  
that wheels are ꢀtted securely and that the  
brake system functions correctly.  
Changing wheels around  
In order to wear the wheels in a uniform man-  
ner, it is recommended to interchange them  
regularly according to the diagram ››› Fig. 197.  
The useful life of all the tyres will then be about  
the same time.  
Winter tyres  
●
Winter tyres must be ꢀtted on all four  
wheels.  
●
Only use winter tyres that are approved for  
your vehicle.  
The wheel bolts must be clean and turn easily.  
1)  
Follow the regulations of the country you are driving in.  
300  
Important informationaboutwheels and tyres  
●
Please note that the maximum permissible  
A code letter indicating the speed limit is stam-  
ped on all winter tyres ››› page 296.  
In the infotainment system's Vehicle settings  
menu, a speed warning can be set in the Tyres  
menu.  
WARNING  
speed for winter tyres may be lower than for  
summer tyres.  
Exceeding the maximum speed permitted for  
the winter tyres ꢀtted on your car can cause  
tyre failure, resulting in a loss of control of  
the vehicle – risk of accident.  
●
Also note that winter tyres are no longer ef-  
fective when the tread is worn down.  
●
After ꢀtting the wheels you must always  
Vehicles capable of exceeding these speeds  
must have an appropriate sticker attached so  
that it is visible to the driver. Suitable stickers  
are available at specialised CUPRA Services,  
SEAT Oꢁicial Service centres and specialised  
workshops. Please note the regulations to this  
eꢁect in your country.  
check the tyre pressures. When doing so,  
take into account the correct tyre pressures  
listed on the rear of the front left door frame  
››› page 298.  
In winter road conditions winter tyres will con-  
siderably improve vehicle handling. The design  
of summer tyres (width, rubber compound,  
tread pattern) gives less grip on ice and snow.  
This applies particularly to vehicles equipped  
with wide section tyres or with high speed  
tyres (code letters H, V or Y on the sidewall).  
For the sake of the environment  
When winter is over, change back to summer  
tyres at an appropriate moment. In tempera-  
tures above +7°C (+45°F), performance will be  
improved if summer tyres are used. Rolling  
noise, wear and energy consumption will all  
be reduced.  
“All-weather” tyres can also be used instead of  
winter tyres.  
Using winter tyres with V-rating  
Snow chains  
Please note that the generally applicable  
240 km/h (149 mph) speed for winter tyres  
with the letter V is subject to technical restric-  
Snow chains may only be ꢀtted to the rear  
wheels.  
Only use winter tyres of the correct type ap-  
proved for your vehicle. The sizes of these  
tyres are speciꢀed in the vehicle's documents  
(e.g. EC Certiꢀcate of Conformity or COC1)).  
The vehicle documentation varies depending  
on the country of residence.  
●
Check that they are correctly seated after  
driving for a few yards; correct the position  
if necessary, in accordance with the manufac-  
turer's ꢀtting instructions.  
tions; the maximum permissible speed for  
your vehicle may be signiꢀcantly lower. The  
maximum speed limit for these tyres depends  
directly on the maximum axle weights for your  
●
car and on the listed weight rating of the tyres  
being used.  
Keep your speed below 50 km/h (30 mph).  
Winter tyres lose a great deal of their proper-  
ties when the tread is worn down to a depth of  
4 mm.  
Snow chains will improve braking ability as well  
as traction in winter conditions.  
It is best to contact a specialised CUPRA Serv-  
ice or SEAT Oꢁicial Service to check the max-  
imum speed which is permissible for the V-  
rated tyres ꢀtted on your car on the basis of  
this information.  
The performance of winter tyres is also se-  
verely impaired by ageing, even if the tread is  
still much deeper than 4 mm.  
For technical reasons, the use of snow chains  
is only permitted on the following rim and tyre  
combinations:  
1)  
COC = certiꢀcate of conformity.  
301  

Related Topics

Popular Owner Manuals