2024-2026 Cupra Terramar SUV Checking and refilling levels User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Checking and refilling levels for Your Cupra Terramar SUV First Generation (2024-2026)

Checking and relling levels
351
Engine compartment
Checking and relling
levels
Engine compartment
Working in the engine compart-
ment
The engine compartment of the vehicle is
a dangerous area. You should only perform
works in the engine compartment if you have
good knowledge of the necessary operations
and the general safety measures, and if you
have adequate tools, means and operating u-
ids. Works performed inadequately could lead
to serious injuries ›››
. In this case, get a
specialised workshop to perform all the works.
CUPRA recommends going to a specialised
CUPRA dealer or any SEAT dealership for this
purpose.
Before performing any work in the engine
compartment, always park the vehicle on level
and rm ground, taking all necessary safety
precautions.
WARNING
Any accidental movement of the vehicle dur-
ing maintenance work could cause serious
injuries.
●
Never perform works underneath the vehi-
cle without having rst immobilised it to pre-
vent it from moving. When working under the
vehicle with the wheels on the ground, the
vehicle must be on a level surface and the
wheels must be locked.
●
If work must be performed underneath
the vehicle, take the extra precaution of sup-
porting it safely using a suitable support as-
sembly. The jack is not suitable for this pur-
pose and may not provide support, which
could lead to serious injuries.
●
The Start-Stop system must be switched o
manually.
WARNING
The engine compartment of any vehicle is a
dangerous area in which serious injuries can
be caused!
●
When performing any type of work, always
ensure you are extremely cautious, and bear
in mind the general safety measures. Never
put yourself at risk.
●
Never perform works in the engine com-
partment if you do not have solid knowledge
of the necessary operations. If you are un-
sure of what needs to be done, seek a speci-
alised workshop to perform the works. Works
performed inadequately could lead to seri-
ous injuries.
●
Never open or close the bonnet if you
see steam or coolant escaping from the en-
gine compartment. Steam or hot coolant can
cause severe burns. Always wait until you stop
hearing or seeing the steam or coolant dis-
charging from the engine compartment.
●
Before opening the bonnet, always wait for
the engine to cool down.
●
Touching hot engine or exhaust system
components could result in skin burns.
●
Turn o the ignition and keep the vehicle
key in a safe place at a safe distance from
the vehicle to prevent the ignition from being
turned on and the combustion engine star-
ted by mistake.
●
Always keep children away from the engine
compartment and never leave them unsu-
pervised.
●
When the engine is hot, its cooling system
is pressurised. Do not open the expansion
tank cap. Hot coolant may splash out and
cause severe burns and other injuries.
–
Turn the coolant expansion tank cap
slowly and very carefully anticlockwise
while pressing it down slightly.
–
Always protect your face, hands and arms
from the hot coolant and steam with a
large thick cloth.
Checking and relling levels
353
Engine compartment
Preparing the vehicle for work in
the engine compartment
Before performing works in the engine com-
partment, always perform the following opera-
tions in the order indicated ›››
:
1. Place the vehicle on level and rm ground,
taking all necessary safety precautions.
2. Press the brake pedal and hold it down until
the ignition is switched o.
3. Apply the electronic parking brake.
4. Automatic transmission: press the parking
lock button P.
5. Switch the ignition o ›››page166.
6. Remove the vehicle key from the vehicle
and store it outside to avoid inadvertently
starting the engine.
7. Wait for the engine to cool down sui-
ciently.
8. Always keep other people away from the
engine compartment.
9. Immobilize the vehicle so that it cannot
move.
WARNING
For your own safety, do not ignore this im-
portant check list, otherwise accidents and
serious injuries could be caused.
●
Always follow the indications on the check
list and always bear in mind the general
safety measures.
Opening and closing the bonnet
Fig.221 Release lever in the driver's footwell
area.
Fig.222 Lever under the bonnet.
Opening the bonnet
The bonnet is released from inside the vehicle.
Before opening the bonnet, make sure that the
windscreen wiper arms are in place against the
windscreen.
●
Open the door and pull the lever that is un-
derneath the instrument panel ›››Fig.221
1
.
●
To lift the bonnet, press towards the left on
the lever located under the bonnet, in the cen-
tre ›››Fig.222
2
. The fastening hooks are
unlocked.
●
The bonnet can be opened.
Closing the bonnet
●
Pull the bonnet down until the force of the
gas spring is overcome.
●
Then let the bonnet engage in the locking
component with a gentle push.
354
Checking and relling levels
WARNING
Make sure that the bonnet is properly closed.
If it opens when driving, it can cause an acci-
dent.
NOTICE
In certain weather conditions, ice or snow
may build up between the bonnet and wind-
screen; do not force the bonnet open until
you are sure that there is no ice or snow, es-
pecially in the hinge area.
NOTICE
To avoid damage to the bonnet and to the
windscreen wiper arms, only open it when
the windscreen wipers are in place against
the windscreen.
Fluids and consumables
Introduction
All uids and consumables, such as engine
coolant or vehicle batteries, are subject to
continuous development. For this reason,
whenever a uid or consumable needs to be
replaced, please contact a specialist workshop.
CUPRA dealers always promptly receive infor-
mation about any modications.
WARNING
If unsuitable uids and consumables are used
or used improperly, accidents, injuries, burns
and severe poisoning can occur.
●
Only store operating uids in their original
containers, tightly closed.
●
Never store operating uids in empty food
cans, bottles or other empty containers, as
they could be ingested by somebody.
●
Keep all uids and consumables out of
reach of children.
●
Always read and observe the information
and warnings given on containers of operat-
ing uids.
●
When using products that emit harmful va-
pours, always work outdoors or in a well-ven-
tilated area.
NOTICE
Use only appropriate operating uids. Never
confuse operating uids. This could result in
serious malfunctions and engine damage!
For the sake of the environment
Leakages of operating uids can contami-
nate the environment. If any operating uid
leaks, collect it in an appropriate container
and dispose of it properly and in an environ-
mentally friendly manner.
Cooling system
Introduction
Only carry out work on the engine cooling sys-
tem yourself if you are familiar with the neces-
sary operations and the generally applicable
safety measures, and if you have the appro-
priate tools, equipment and operating uids.
Works performed inadequately could lead to
serious injuries . In this case, get a specialised
workshop to perform all the works. CUPRA rec-
ommends going to a specialised CUPRA dealer
or any SEAT dealership for this purpose.
WARNING
Engine coolant is toxic!
●
Only store coolant in its original container,
tightly closed and in a safe place.
●
Never store motor coolant in empty food
cans, bottles or other empty containers, as it
could be ingested by another person.
●
Always keep motor coolant out of reach of
children.
●
Ensure that the coolant uid additive per-
centage is correct, taking into account the
lowest ambient temperature expected in the
location where the vehicle is to be used.
Checking and relling levels
355
Cooling system
●
When the outside temperature is very low,
the coolant could freeze and the vehicle
could be immobilised. In this case, the heat-
ing would not work either and inadequately
dressed passengers could die of cold.
For the sake of the environment
Coolants and additives can contaminate the
environment. If any operating uid leaks out,
collect it and dispose of it properly and in an
environmentally friendly manner.
Coolant specications
The factory tted engine cooling system is l-
led with a mixture of specially treated water
and at least 40% coolant additive G12evo (TL-
VW 774 L).
Get information from a specialist workshop
about which coolant is suitable for your vehi-
cle. CUPRA recommends going to a specialised
CUPRA dealer or any SEAT dealership for this
purpose.
To protect the engine cooling system, the ad-
ditive percentage should always be at least
40%. If more antifreeze protection is required
for climatic reasons, the additive proportion
can be increased. However, it should only be
increased up to a maximum of 55%, otherwise
the antifreeze protection would be reduced
and the cooling eect would be impaired.
The G12evo (TL-VW 774 L) can be recognised
by its lilac colouring. This mixture of water
and additive not only provides antifreeze pro-
tection down to -25°C (-13°F), but also pro-
tects the light alloy parts of the cooling system
against corrosion, prevents limescale build-up
and considerably raises the boiling point of the
coolant.
When topping up the coolant, a mixture of
distilled water and at least 40% of the appro-
priate coolant additive should be used for opti-
mum corrosion protection ›››
page356.
WARNING
If the vehicle’s cooling system does not have
suicient antifreeze protection, the engine
could fail and this could result in serious in-
jury.
●
Ensure that the coolant uid additive per-
centage is correct, taking into account the
lowest ambient temperature expected in the
location where the vehicle is to be used.
●
When the outside temperature is very low,
the coolant could freeze and the vehicle
could be immobilised. In this case, the heat-
ing would not work either and inadequately
dressed passengers could die of cold.
NOTICE
Never mix the original additives for the
G12evo coolant (TL-VW 774 L) with motor
coolant uid not authorised by CUPRA.
●
If the uid in the expansion tank does not
have a pink colour (resulting from mixing the
lilac additive with distilled water), but is, for
example, brown, the suitable coolant may
have been mixed with another unsuitable
one. The coolant must be changed as soon as
possible if this is the case! Otherwise serious
malfunctions or damage to the engine and
the cooling system could occur!
For the sake of the environment
Motor coolant and its additives can pollute
the environment. If any operating uid leaks
out, collect it and dispose of it properly and
in an environmentally friendly manner.
356
Checking and relling levels
1
2
Coolant tank
✓ Valid for: hybrid vehicles.
Fig.223 Engine compartment: Coolant
tanks
Hybrid vehicles have 2 independent coolant
expansion tanks.
›››
Fig.223
Coolant expansion tank for the combus-
tion engine ›››Fig.224.
Coolant expansion tank for the high-volt-
age system ›››Fig.225.
Check and rell the coolant
Engine cooling uid
Fig.224 In the front compartment: coolant
expansion tank.
Preliminary steps
●
Park the vehicle on a rm, at surface.
●
Wait until the engine has fully cooled ››› .
●
Open the front bonnet ›››page351.
●
The engine coolant expansion tank can
be recognised by the symbol on the cap
›››Fig.224.
Check the level
When the vehicle is delivered (new vehicles),
the coolant may be above the marked area.
This is normal. It is not necessary to suck the
coolant out.
1. When the engine is cold, check the cool-
ant level using the side marking on the
expansion tank ›››Fig.224. The coolant
level should be between the marks.
2. If the level is below the minimum level
mark ( ) on the tank, top up with coolant.
When the engine is warm, the coolant level
may be slightly above the upper mark.
3. Do not add coolant if there is no more
coolant visible in the coolant expansion
tank ››› .
The coolant level cannot be checked accu-
rately on all models as the visibility of the uid
level in the coolant expansion tank may be ob-
structed. If the coolant level cannot be read
accurately, contact a qualied workshop.
When the motor coolant level is too low, the
coolant warning light comes on. In this case,
immediately seek assistance from specialist
personnel.
Checking and relling levels
357
Cooling system
Topping up the uid
If the coolant level is too low and there is no
workshop nearby, note the following:
1. Always protect your face, hands and arms
from hot coolant or steam by placing a
suitable cloth over the cap of the motor
coolant expansion tank.
2. Carefully unscrew the cap.
3. Only top up with fresh coolant according
to specications ›››page355.
Only top up with coolant if there is still
some coolant left in the expansion tank;
otherwise the engine could be damaged!
If you do not see any coolant in the ex-
pansion tank, do not continue driving and
seek specialist assistance.
4. If there is still some coolant left in the ex-
pansion tank, top up with coolant up to the
tank’s upper mark and check the level the
next day. If the level drops again, go to a
workshop and request a check of the cool-
ing system.
The coolant level must be between the
marks on the expansion tank ›››Fig.224.
Never exceed the top edge of the
marked area .
5. Screw the cap on tightly.
If engine coolant with the recommended
specications is not available in an emergency,
do not use any other coolant additive! In this
case, top up with distilled wateronly. Next, en-
sure that the recommended additive is topped
up as soon as possible in the correct propor-
tion ›››page355.
High voltage system coolant (valid for hybrid
vehicles)
Fig.225 In the front compartment: coolant
expansion tank.
Preliminary steps
●
Park the vehicle on a rm, at surface.
●
Wait for the high voltage system to cool down
››› .
●
Open the front bonnet ›››page351.
●
The high voltage system's coolant expansion
tank can be recognised by the symbol on the
cap
›››Fig.225.
Check the level
When the vehicle is delivered (new vehicles),
the coolant may be above the marked area.
This is normal. It is not necessary to suck the
coolant out.
1. Check the coolant level on the side marks
of the expansion tank when the coolant is
cold ›››
Fig.225. The coolant level should
be between the marks.
2. If the level is below the minimum level
mark ( ) on the tank, top up with coolant.
When the coolant is hot, the coolant level
may be slightly above the upper mark.
3. Do not add coolant if no coolant at all is
visible in the high voltage system ›››
coolant expansion tank.
The coolant level cannot be checked accu-
rately on all models as the visibility of the uid
level in the coolant expansion tank may be ob-
structed. If the coolant level cannot be read
accurately, contact a qualied workshop.
Topping up the uid
If the coolant level is too low and there is no
workshop nearby, note the following:
1. Always protect your face, hands and arms
from hot liquid coolant or steam by placing
a suitable cloth over the coolant expansion
tank cap.
2. Carefully unscrew the cap ›››
.
358
Checking and relling levels
3. Add only fresh coolant according to the
manufacturer's specication up to the up-
per level mark. After adding the coolant,
the coolant level must be between the
marks on the high voltage system coolant
expansion tank ›››Fig.225.
4. Close the cap tightly.
5. The next day, check the high voltage sys-
tem coolant level. If the level in the coolant
expansion tank has fallen below the mark
, have the cooling system checked by a
specialist workshop.
If in an emergency you do not have access to
coolant with the required specications, only
add distilled water in the rst instance. After-
wards, take the vehicle to a specialist workshop
as soon as possible to have the correct coolant
additive mixture restored.
WARNING
Steam and hot engine coolant can cause se-
vere burns.
●
Never open the front bonnet if you see
or hear steam or coolant escaping from the
front compartment. Always wait until you can
no longer see or hear steam or coolant es-
caping. Touching hot parts can result in skin
burns.
WARNING
Before opening the front bonnet, please
note the following:
●
Apply the electronic parking brake.
●
Always keep children away from the front
compartment and never leave them unat-
tended.
WARNING
When the engine is hot, its cooling system is
pressurised. Do not open the expansion tank
cap. Hot coolant may splash out and cause
severe burns and other injuries.
●
Turn the cap slowly and very carefully anti-
clockwise while pressing it down slightly.
●
Always protect your face, hands and arms
from the hot coolant and steam with a large
thick cloth.
NOTICE
Only use distilled water! Other types of wa-
ter contain chemical substances that could
cause signicant corrosion damage. If you
have added non-distilled water, have all of
the engine cooling system uid changed im-
mediately by a specialist workshop.
●
When adding coolant, do not ll above the
upper edge of the marked area ›››Fig.224,
›››Fig.225. Otherwise, when the temper-
ature rises the excess uid will be expelled
from the engine cooling system and could
cause damage.
●
If the system leaks a lot of coolant, only
rell once the motor has cooled down com-
pletely. If there is a signicant loss of coolant,
there may be leaks in the cooling system. Im-
mediately go to a specialist workshop to have
the system checked. This could result in en-
gine damage.
●
Do not add coolant if the expansion tank
is completely empty! Air may have got into
the cooling system. Do not continue driving
and seek assistance from specialist person-
nel. This could result in engine damage.
●
When changing the operating uids, make
sure that you pour the correct uids into the
correct ller necks. Using the wrong operat-
ing uids can lead to serious malfunctions
and engine damage.
Checking and relling levels
359
Brake uid
Brake uid
Check and rell the brake uid
Fig.226 Front compartment: brake uid
reservoir cap.
Checking the brake uid level
The brake uid level must be between the
and markings.
However, if the brake uid level goes down no-
ticeably in a short time, or drops below the
mark, there may be a leak in the brake sys-
tem. Seek specialist assistance. A warning light
on the instrument cluster display monitors the
brake uid level.
Brake uid level
The control lamp lights up red.
Brake uid level is too low.
●
Stop driving!
●
Check the brake uid level.
●
If the brake uid level is too low, seek special-
ist assistance.
Changing brake uid
We recommend that you have the brake uid
changed by a Technical Service.
WARNING
If the brake uid level is low or unsuitable/old
brake uid is used, the brake system may fail
or braking power may be reduced.
●
Check the brake system and the brake uid
level regularly!
●
When the brake uid is used and brakes are
subjected to extreme braking forces, bub-
bles of vapour form in the brake system.
These bubbles can signicantly reduce brak-
ing power, notably increasing braking dis-
tance, and could result in the total failure of
the brake system.
●
Be sure to always use the correct brake
uid. Only use brake uid that expressly
meets the VW 501 14 standard.
●
You can buy VW 501 14 standard brake uid
at a specialised CUPRA service or at a SEAT
Oicial Service. If none is available, use only
high-quality brake uid that meets DIN ISO
4925 CLASS 4 standards, or USA Standards
FMVSS116DOT4.
●
The replacement brake uid must be new.
●
Brake uid should be stored in the closed
original container in a safe place out of reach
of children. Risk of poisoning!
NOTICE
Brake uid should not come into contact
with the vehicle paintwork, as it is abrasive.
Note
Brake uid is an environmental pollutant.
Collect any spilt service uids get a profes-
sional to dispose of them.
360
Checking and relling levels
Windscreen washer reser-
voir
Checking the level of the wind-
screen washer reservoir and rell-
ing it
Fig.227 In the front compartment: blue
cap of the windscreen washer reservoir.
Check the water level in the windscreen
washer reservoir regularly and top up as re-
quired.
The windscreen washer reservoir contains liq-
uid detergent for the windscreen and rear win-
dow.
There is a sieve in the ller neck of the washer
uid tank. When lling the tank, this sieve re-
tains large dirt particles so that they do not
reach the nozzles. Do not remove the sieve
except for cleaning. If the sieve is damaged or
not tted, these dirt particles could enter the
system during lling and clog the windscreen
washer nozzles.
●
Raise the bonnet ››› on page351.
●
The windscreen washer reservoir is marked
with the symbol on the cap.
●
Check if there is enough uid in the tank.
Plain water is not enough to clean the wind-
screen and headlights. We recommend that
you always add a product to the windscreen
washer uid.
The capacity of the windscreen washer reser-
voir is approximately 3 litres.
NOTICE
If the water from the windscreen washer does
not contain enough antifreeze, it may freeze
on the windscreen and rear window, reducing
forward and rear visibility.
●
In winter, ensure the windscreen washer
contains enough antifreeze.
●
In cold conditions, you should not use the
windscreen wiper system unless you have
warmed the windscreen with the ventilation
system. The antifreeze could freeze on the
windscreen and reduce visibility.
NOTICE
Never mix an unsuitable antifreeze or other
similar additives with the windscreen washer
water. A greasy layer may be formed on the
windscreen which will impair visibility.
●
Use clean water with a window cleaner rec-
ommended by CUPRA.
●
If necessary, add a suitable antifreeze to
the water in the reservoir.
NOTICE
●
Do not mix cleaning products recommen-
ded by CUPRA with other products. This
could lead to occulation and may block the
windscreen washer jets.
●
When topping up service uids, make ab-
solutely certain that you ll the uids into
the correct reservoirs. Using the wrong uids
could cause serious malfunctions.
●
Lack of window washer uid causes the
view through the windscreen to be obscured.
Checking and relling levels
361
Engine oil
A
B
–
Engine oil
General notes
Fig.228 In the engine compartment:
engine oil label
Fig.229 In the engine compartment: area
where the engine oil label is located
Key to ›››
Fig.228:
Information about the engine oil standard.
Information about engine oil viscosity.
The engine comes with a special, multi-grade
oil that can be used all year round.
Because the use of high-quality oil is essential
for the correct operation of the engine and its
long useful life, when topping up or changing
oil, use only those oils that comply with VW
standards.
For vehicles with an engine oil label
If the engine oil has to be topped up, use one
of the oils shown on the label ›››
Fig.228.
The label with the prescribed standard is loca-
ted at the front of the engine compartment
›››Fig.229
1
. If you use the recommended
engine oil, you can top up the oil as often as
necessary.
For vehicles without an engine oil label
Go to a specialised workshop, a specialised
CUPRA dealer or SEAT Oicial Service to get
information on the corresponding standard.
If the engine oil level is too low
If the recommended engine oil is not available,
in the event of an emergency you can change
the oil once with a maximum of 0.5 l of the
next oil until the next oil change:
Petrol engines: standard VW50400,
ACEAC3, ACEAC4, APISN or IL-
SACGF-6A.
CUPRA recommends changing the oil at a spe-
cialised workshop. CUPRA recommends a spe-
cialised CUPRA Service or SEAT Oicial Serv-
ice.
NOTICE
CUPRA recommends the use of engine oils
approved according to the appropriate VW
standard. Use of engine oils that do not meet
these quality requirements can cause engine
damage.
CUPRA recommends the use of Original SEAT
Spare Part engine oils.
Engine oil additives
No type of additive should be mixed with the
engine oil. The deterioration caused by these
additives is not covered by the warranty.
Depending on how you drive and the condi-
tions in which the vehicle is used, oil consump-
tion can be up to 0.5 l/1000km. Oil consump-
tion is likely to be higher for the rst 5,000km.
For this reason the engine oil level must be
checked at regular intervals, preferably when
lling the tank and before a journey.
NOTICE
0.5l of engine oil of one of the indicated
engine oil standards may be used, only in the
event of an emergency and in exceptional
cases.
362
Checking and relling levels
NOTICE
Take the following into account if you have
relled with an engine oil dierent to those
specied in the aforementioned standards,
or by your SEAT technical service centre:
●
There is no way of completely avoiding the
danger of causing damage to the engine and
particulate lter.
●
You can continue driving with the vehicle if
the rell was no more than 0.5l of engine oil.
Go to a specialised workshop as soon as pos-
sible and request an oil change. Otherwise,
there is a danger of engine damage.
●
If you have topped up more than 0.5l
of engine oil, drive with the engine at low
load levels and within the medium RPM range
as a maximum. Do not drive at more than
80km/h and do not travel more than 300km
(approximately). Go to a specialised work-
shop as soon as possible and request an oil
change. Otherwise, there is a danger of en-
gine damage.
●
You are responsible for the risk of possible
damage to the vehicle (engine, exhaust sys-
tem). If in doubt, do not start the engine and
request assistance from the technical service
centre.
●
Do not start the engine if you have topped
up with a uid other than engine oil. Request
assistance from the technical service centre.
Danger of engine damage!
Note
Before a long trip, we recommend nding an
engine oil that conforms to the correspond-
ing VW specications and recommend keep-
ing it in the vehicle. This way, the correct en-
gine oil will always be available for a top-up if
needed.
●
If the label showing the engine oil speci-
cations is missing ›››
Fig.228, please con-
tact a specialist workshop.
Checking and topping up the en-
gine oil level
Checking the oil level in vehicles with a dip-
stick
Fig.230 Engine oil dipstick.
A
Do not top up oil in any case.
B
You can add oil but keep the level in that
zone.
C
The oil level is too low. Add oil up to zone
B
.
Before opening the bonnet, read and observe
the warnings ›››
page351, Working in the
engine compartment.
The engine oil dipstick indicates the level of
the oil.
●
Park the vehicle in a horizontal position.
●
Briey run the engine at idle speed until the
operating temperature is reached and then
stop.
●
Wait for about two minutes.
●
Locate the oil level dipstick. It can be recog-
nized by its coloured upper end.
●
Pull out the dipstick. Wipe the dipstick with a
clean cloth and insert it again, pushing it in as
far as it will go.
●
Then pull it out again and check the oil level
›››Fig.230. Top up with engine oil if neces-
sary.
The oil should leave a mark between the areas
A
and
C
. It must never exceed zone
A
.
Checking and relling levels
363
Engine oil
A
B
C
D
Checking the oil level on the digital display
on vehicles without a dipstick
Fig.231 On the infotainment system screen:
possible engine oil level indicator displays.
A
Do not top up engine oil
B
Engine oil level in normal range.
C
Engine oil level low, engine oil must be
topped up.
D
Engine oil level very low, engine oil needs
to be topped up.
To check the oil level on the information
screen, the following steps must be followed:
1. Switch the ignition on.
2. Select the menu:
Vehicle > Status > Oil
level.
Possible actions after reading the oil level on
the information screen ›››Fig.231:
Do not top up engine oil, do not start the
engine and seek professional assistance.
Oil level correct.
Oil level low, engine oil must be topped up.
Oil level below minimum, engine oil must
be topped up.
If the oil level is in the lower area of
B
or in the
area
C
, it can be topped up to half of the area
B
(approx. 0.5l). Or follow the instructions on
the information screen.
Topping up engine oil
Fig.232 Oil ller cap cover in the engine
compartment.
●
Locate the engine oil ller cap. It can be
recognized by the symbol
on the cover
›››Fig.232.
●
Unscrew cap from the oil ller mouth
›››Fig.232.
●
Carefully add oil in small quantities (no more
than 0.5 l).
●
To avoid adding too much oil, whenever you
add a certain amount, wait about 2 minutes
and recheck the oil level ›››page362.
●
If necessary, add some more oil.
●
When the oil level reaches at least zone
›››Fig.230
B
, carefully screw on the engine
oil ller cap ›››
.
Engine oil specication ›››page361.
WARNING
Any work carried out in the engine compart-
ment or on the engine must be carried out
cautiously.
●
When working in the engine compart-
ment, always observe the safety warnings
›››page351.
WARNING
Oil is highly inammable! Ensure that no oil
comes into contact with hot engine compo-
nents when topping up.
NOTICE
If the oil level is above zone
A
, do not start
the engine. This could result in damage to
the engine and catalytic converter. Contact a
Technical Service.
364
Checking and relling levels
For the sake of the environment
Under no circumstances should the oil level
be above zone
A
. Otherwise oil can be
drawn in through the crankcase breather and
leak into the atmosphere via the exhaust sys-
tem.
Note
Before a long trip, we recommend nding an
engine oil that conforms to the correspond-
ing VW specications and recommend keep-
ing it in the vehicle. This way, the correct en-
gine oil will always be available for a top-up if
needed.
Engine oil change
We recommend that you have the engine oil
changed by a Technical Service.
WARNING
Only change the engine oil yourself if you
have the specialist knowledge required!
●
Before opening the bonnet, read and ob-
serve the warnings ›››page351.
●
Wait for the engine to cool down. Hot oil
may cause burn injuries.
●
Wear eye protection to avoid injuries, such
as acid burns, caused by splashes of oil.
●
When removing the oil drain plug with your
ngers, keep your arm horizontal to help
prevent oil from running down your arm.
●
Wash your skin thoroughly if it comes into
contact with engine oil.
●
Engine oil is poisonous! Used oil must be
stored in a safe place out of the reach of chil-
dren.
NOTICE
No additives should be used with engine
oil. This could result in engine damage. Any
damage caused by the use of such additives
would not be covered by the factory war-
ranty.
For the sake of the environment
●
We recommend that you change the en-
gine oil and the lter at a technical service
centre.
●
Never pour oil down drains or into the
ground.
●
Use a suitable container when draining the
used oil. It must be large enough to hold all
the engine oil.
Troubleshooting
Engine oil pressure too low.
The indicator lamp lights up red.
Do not carry on driving! Switch o the
engine. Check the engine oil level.
●
If this warning lamp starts to ash, and
is accompanied by three audible warnings,
switch o the engine and check the oil level.
If necessary, add more oil ›››page362.
●
If the warning lamp ashes although the
oil level is correct, stop driving. Do not even
run the engine at idle speed! Seek professional
assistance.
Engine oil level very low.
The warning lamp ashes red and a message
is shown on the dash panel: “ Add engine oil
now”
Do not carry on driving! This could result
in engine damage.
1. Safely stop the vehicle as soon as possible.
2. Stop the engine.
3. Check the oil level ›››page362.
4. If necessary, add engine oil gradually in
small quantities, do not exceed a total of
0.5l and observe the lling indications on
the instrument cluster display.
If the warning lamp is lit up even if the oil level is
correct, do not continue driving. Engine dam-
age may occur. Seek assistance from the tech-
nical service.
Checking and relling levels
365
12-volt battery
Engine oil level too low
The indicator lamp lights up yellow.
●
Check the engine oil level as soon as possible
›››page362.
●
Change the oil as soon as you have the op-
portunity to do so.
Engine oil level too high
The warning lamp lights up yellow and a mes-
sage is shown on the dash panel.
●
Safely stop the vehicle as soon as possible.
●
Stop the engine.
●
Check the oil level ›››page362.
●
If the oil level is too high, do not continue
driving or leave the engine running. Engine
damage may occur. Seek assistance from the
technical service.
Oil level sensor fault
The control lamp ashes yellow.
●
Have the check done by a specialised work-
shop.
●
Until then it is advisable to check the oil level
every time you refuel.
12-volt battery
Introduction
The 12volt battery is located in the engine
compartment or in the luggage compartment
(PHEV hybrid vehicles). The 12volt battery is
checked and, if necessary, replaced as part of
maintenance work.
All work on batteries requires specialist knowl-
edge. Please refer to a specialised CUPRA
Service, SEAT Oicial Service or a workshop
specialising in batteries: risk of burns or ex-
ploding battery!
The battery must not be opened! Never try to
change the uid level of the battery. Otherwise
explosive gas is released from the battery that
could cause an explosion.
Battery warning indications
Wear protective goggles.
Battery acid is extremely corrosive. Wear
protective gloves and eye protection.
Rinse any splashes of electrolyte with
plenty of water.
Fires, sparks, open ames and smoking
are prohibited.
The battery should only be charged in a
well-ventilated zone. Risk of explosion!
Keep children away from acid and the bat-
tery.
Always follow the instruction manual.
If the vehicle is not used for long periods
The vehicle has a system for monitoring
the current consumption when the engine
is left unused for extended periods of time
›››
page372. Some functions, such as the in-
terior lights, or the remote door opening, may
be temporarily disabled to prevent the battery
from running at. These functions will come
back on as soon as the ignition is switched on
and the engine started.
WARNING
Working on the 12-volt battery and electrical
system can cause severe burns, re and elec-
tric shock. Always read and observe the fol-
lowing warnings and safety precautions be-
fore working on the battery:
●
Before working on the 12-volt battery,
switch o the ignition and all electrical con-
sumers and disconnect the negative cable
from the battery.
●
Always keep children away from the 12-volt
battery electrolyte and the battery itself.
●
Always wear eye protection and protective
gloves.
366
Checking and relling levels
●
The battery electrolyte is very corrosive. It
can cause skin burns and blindness. When
handling the 12-volt battery, protect your
hands, arms and face in particular from acid
splashes
●
Do not smoke while working and never
work in the vicinity of naked ames or sparks.
●
Avoid sparks caused by electrostatic dis-
charges, just like when handling electric ca-
bles and devices.
●
Never short the battery terminals.
●
Never use damaged 12-volt batteries. They
could explode. If the 12-volt battery is dam-
aged, replace it immediately.
●
Never use a frozen 12 volt battery. When
the battery is discharged, it may freeze at
temperatures close to 0°C (+32°F). If the 12-
volt battery is frozen, replace it immediately.
NOTICE
Do not expose the 12-volt battery to direct
sunlight for a prolonged period of time.
●
Ultraviolet rays can damage the battery
casing.
NOTICE
If the vehicle is not to be used for a long pe-
riod of time, protect the 12-volt battery from
frost.
●
The battery may freeze and, as a result,
suer irreparable damage.
Note
After starting the engine with a deeply dis-
charged or newly replaced 12-volt battery,
or after a jump start, some system settings
(time, date, personalised comfort settings
and programs) may be incorrectly set or de-
leted. Check and correct these settings once
the battery is suiciently charged.
Note
During the winter, the starting power may be
reduced, and if necessary, the battery should
be charged.
Check the electrolyte level
Fig.233 Hybrid vehicles (PHEV): location of
the battery in the luggage compartment
Fig.234 Sight glass on the top of the 12
volt battery (schematic representation).
Access to the 12 volt battery
The 12-volt battery is located in the engine
compartment (conventional vehicles) or in the
left side of the luggage compartment (PHEV
hybrid vehicles).
Valid for conventional and Mild Hybrid vehicles:
●
Raise the bonnet ››› in Working in the
engine compartment on page351.
●
Lift the cover that protects the front of the
battery.
Valid for hybrid vehicles (PHEV):
●
Open the luggage compartment.
●
Pull the handle
A
›››
Fig.233 to open the
12-volt battery protection cover.
NOTICE
Do not cover or cover the cooling grille of the
12-volt battery
B
›››
Fig.233.
Checking and relling levels
367
12-volt battery
Yellow or colourless:
Black:
Check the level
The electrolyte level should be checked regu-
larly in high-mileage vehicles, in hot countries
and in older batteries.
●
Check the colour display in the sight glass on
the top of the battery ›››Fig.234.
●
If there are air bubbles in the window, tap
the window gently until they disperse.
The “magic eye” indicator, located on the top
of the battery changes colour, depending on
the charge state and electrolyte level of the
battery.
There are two dierent colours:
The battery's electrolyte
level is too low. Go to a specialised work-
shop to have the battery checked and re-
placed if necessary.
The battery’s electrolyte level is cor-
rect.
Charging, replacing, disconnecting
and connecting the 12-volt battery
If you suspect that the 12-volt battery is dam-
aged or defective, have it checked by a quali-
ed specialist workshop.
Charging the 12-volt battery
Contact a specialist workshop for charging the
12-volt battery, as the battery model tted in
the vehicle in the factory uses a technology
that requires limited voltage charging ›››
.
CUPRA recommends going to a specialised
CUPRA dealer or any SEAT dealership for this
purpose.
WARNING
Carefully read the warnings regarding the ve-
hicle's 12 volt battery before handling it.
Warning: Danger!
Always follow the instructions for the 12
volt battery as described in the vehicle’s
owner’s manual.
Vehicle’s 12V battery. Live compo-
nent. Improper handling can cause
short circuits!
All work on the vehicle's 12V battery
must be performed by specialised
companies
The exceptions are:
●
Charging the vehicle’s 12-volt battery
●
Starting the vehicle with external assis-
tance ›››
page340.
Inappropriate handling of the vehicle’s
12 volt battery can cause serious injuries
or death. Maintenance work on the ve-
hicle's 12-volt battery should only be car-
ried out by properly qualied and trained
specialists.
Replacing the 12-volt battery
The 12-volt vehicle battery has been designed
to suit its location and has special safety fea-
tures. If a 12-volt battery needs to be replaced,
the replacement battery must be installed by
a qualied technician. CUPRA recommends
that you visit a CUPRA dealer. Component in-
formation regarding size, maintenance, power
and safety characteristics to be met can be ob-
tained from a qualied technician, who should
have the necessary documentation and tech-
nical equipment. CUPRA recommends visiting
a specialised CUPRA dealer or any SEAT deal-
ership.
The degassing hole of the 12-volt battery must
always be on side of the negative pole. The
degassing hole on the side of the positive pole
must always be sealed.
Only use maintenance-free 12-volt batteries
that comply with the TL82506 and VW75073
standards. These standards must be dated Oc-
tober 2014 or later.
The 12-volt battery must always be replaced
by a qualied technician, as the vehicle's elec-
tronic system must also be adjusted as part of
the replacement. In addition, the battery pa-
rameters relating to operational safety can only
be determined with the original battery. Only
368
Checking and relling levels
a qualied technician has both access to the
right technology to make the adjustment and
the correct replacement batteries.
NOTICE
The use of batteries that do not meet CU-
PRA’s quality specications, or with a ca-
pacity lower than that tted as standard,
could, depending on the local legislation in
each country, lead to the loss of approval or
the corresponding administrative permits for
the vehicle. In addition, it may pose a serious
safety risk.
Vehicles with Start-Stop functions (
›››
page175) are tted with a special battery.
Therefore, it must only be replaced with a bat-
tery of the same specications.
Disconnecting the 12-volt battery
If the 12-volt battery is to be disconnected
from the vehicle's electrical system, please
note the following:
●
Switch o all electrical consumers.
●
Before disconnecting the battery, unlock the
vehicle, otherwise the alarm will be triggered.
●
First disconnect the negative cable and then
the positive cable ›››
.
Connecting the 12-volt battery
●
Switch o all electrical consumers before re-
connecting the 12-volt battery.
●
First reconnect the positive cable and then
the negative one ››› .
After connecting the 12-volt battery and
switching on the ignition, several control lamps
may light up. These lamps go out after a short
distance at a speed of approx. 15 to 20 km/h
(10 to 12 mph). If the warning lights do not go
out, visit a specialist workshop and have the
vehicle checked.
If the 12-volt battery has been disconnected
for a long period of time, it is likely that
the next service will not be correctly indi-
cated or calculated ›››page16 . In this
case it will be necessary to take into account
the maximum permitted maintenance intervals
›››page391.
Vehicles with a “Keyless Access” system
›››page101: If the ignition cannot be
switched on after connecting the 12-volt bat-
tery, lock and unlock the vehicle from the out-
side. Then try to switch on the ignition again.
If the ignition does not work, seek professional
assistance.
WARNING
Attaching the 12-volt battery incorrectly or
using unsuitable batteries may result in short
circuits, re and serious injury.
●
Use only maintenance-free 12 volt batter-
ies with an anti-spill system with the same
properties, specications and dimensions as
the factory-tted battery.
WARNING
Charging the 12-volt battery creates a highly
explosive mixture of detonating gases.
●
Only charge the 12-volt battery in a well-
ventilated place.
●
Never charge a 12-volt battery that is fro-
zen or has thawed. When the battery is dis-
charged, it may freeze at temperatures close
to 0°C (+32°F).
●
If the 12-volt battery has frozen, have it re-
placed without fail.
●
A short circuit may occur if the wires are
incorrectly connected to the poles. First
connect the positive cable and then the neg-
ative one.
Checking and relling levels
369
12-volt battery
NOTICE
●
Never connect or disconnect the 12-volt
battery when the ignition is switched on or
the engine is running. Also, never use a 12-
volt battery that does not meet the vehicle's
battery specications. The electrical system
or certain electronic components could be
damaged and electrical malfunctions could
occur.
●
Never connect accessories that supply
power, such as solar panels or battery charg-
ers, to the 12-volt socket or cigarette lighter,
to charge the 12-volt battery. This could
damage the vehicle's electrical system.
For the sake of the environment
●
The battery may contain toxic substances,
such as sulphuric acid and lead. Dispose of
the 12-volt battery in accordance with the
applicable regulations.
●
Electrolyte can contaminate the environ-
ment. If any operating uid leaks out, collect
it and dispose of it properly.
Troubleshooting
12-volt battery
The control lamp lights up in RED.
The following message is displayed:
Error: 12-V power supply. Park safely! Please
refer to the instruction manual.
Stop driving! Stop the vehicle at the rst
opportunity and in a safe place. The 12-volt
battery is not recharging while the vehicle is in
motion and has a critical charge level, or there
is a fault in the on-board 12-volt network.
●
Switch o the ignition and any electrical con-
sumers that are not required.
●
Contact a specialised workshop.
●
Request a check of the electrical system.
12-volt battery
The indicator lamp lights up YELLOW.
The following message is displayed:
The 12-V battery is not charged. You may
only continue driving with limitations.
The vehicle battery stops charging while driv-
ing As the battery gradually discharges, switch
o all electrical devices that are not essential.
Due to this fault, you will only be able to drive
for a limited period of time. Once this time has
elapsed, a red warning lamp will be displayed.
Drive with caution.
●
Have the electrical system checked by a
qualied workshop.
12-volt battery
The indicator lamp lights up YELLOW. The fol-
lowing message is displayed:
Error: 12 V battery. Restart impossible. Go to
the workshop.
There is a fault in the connection between the
on-board network and the 12-volt battery.
If the drive system is switched o in this situa-
tion, it cannot be switched on again. If neces-
sary, use the jump leads ›››
page340 or seek
assistance from qualied personnel.
●
Contact a specialised workshop.
●
Request a check of the electrical system.
12-volt battery
The indicator lamp lights up YELLOW. The fol-
lowing message is displayed:
12-V battery charge low. Please refer to the
instruction manual.
Starting capability may be limited and may not
be able to start the drive system. If the drive
system can be started, charge while driving. If
this driver message goes out after a certain
amount of time, the vehicle's battery has re-
charged while driving and reached a suicient
level. If the driver message does not go out,
take the vehicle to a specialized workshop.
12-volt battery
The indicator lamp lights up YELLOW. The fol-
lowing message is displayed:
370
Checking and relling levels
12-V power supply limited. Drive with extra
caution.
The 12-volt power supply is limited because
the 12V battery is discharged or not working
at full performance, for example due to very
cold outside temperatures. The 12-volt battery
can be charged while driving. Until the warning
disappears, you should drive with care.
12-volt battery
The indicator lamp lights up YELLOW. One of
the following messages is displayed:
Error: 12-V supply. Please visit workshop.
Error: 12-V battery. Please visit workshop.
There is a fault in the 12-volt power supply:
●
Contact a specialised workshop.
●
Have the electrical system checked.
12-volt battery
The indicator lamp lights up YELLOW. The fol-
lowing message is displayed:
The 12V battery is being discharged. Switch
on the engine.
With the engine o, this message may appear
a few seconds after turning on the ignition.
However, this is normal. It simply alerts you
that the 12-volt battery is discharging. As soon
as the engine is started, the lamp will switch o.
48-volt battery
General information
✓ Valid for: Mild Hybrid vehicles (MHEV)
Fig.235 48-volt battery: hazard warning
1
Never expose the 48 volt battery to sour-
ces of re, sparks or unprotected ames.
2
The instruction manual and the workshop
documentation contain further informa-
tion and warnings in this regard.
3
Always keep children away from the 48 volt
battery.
4
If the 48-volt battery is damaged, uid can
leak and very corrosive acids can form.
The battery should only be handled by
qualied personnel.
5
All maintenance works involving the 48
volt battery should only be performed by
duly qualied and trained technical sta .
6
Take care when handling ammable sub-
stances.
In addition to a 12-volt battery, the vehicle may
be tted with a 48-volt battery located under-
neath the front passenger seat.
The works that are to be carried out on the 48
volt battery should be performed exclusively
by a specialised workshop with duly qualied
technical sta, trained according to CUPRA
guidelines.
Overview of the 48 volt system
The 48 volt system consists of the following
components, among others:
●
48-volt battery
●
12V/48V voltage converter
●
48 volt alternator/starter motor
●
Purple 48 volt cables
48 volt battery warnings
There is a hazard warning sign on the 48 volt
battery ›››Fig.235.
Checking and relling levels
371
48-volt battery
WARNING
Inappropriate handling of the 48 volt battery
can cause serious injuries or death.
●
All maintenance works involving the 48 volt
battery should only be performed by duly
qualied and trained technical sta .
●
Never make any changes to the 48 volt bat-
tery.
WARNING
Make sure the 48 volt battery does not come
into contact with water or other uids.
●
Liquids may cause short circuits, electrical
shocks and burns.
Troubleshooting
✓ Valid for: Mild Hybrid vehicles
Control lamps and driver messages on the in-
strument cluster display or infotainment sys-
tem:
48-volt battery
The indicator lamp lights up red. The following
message is displayed:
Battery: Risk of re! Stop safely and get out
quickly. Call the emergency services.
The 48V battery temperature is too high
.
If this message is displayed on the instrument
cluster, follow the steps below:
●
Stop driving! Stop the vehicle immedi-
ately, taking into account the traic situation.
●
Choose a safe place outdoors, away from
buildings or vehicles, canopies, covered car
parks or similar places.
●
If possible, switch on the hazard warning
lights.
●
Before leaving the vehicle, make sure it is im-
mobilised (parking brake, parking lock P).
●
Switch o the ignition and leave the ignition
key on the dash panel or in a visible place so
that the emergency services can use it (for ex-
ample to recover the vehicle from a hazardous
area).
●
Exit the vehicle and make sure that there are
no other people or animals left inside.
●
Make sure that you leave the danger zone
together with all other vehicle occupants and
that everyone remains in an area that is protec-
ted from traic (e.g. behind the guard rail).
●
Notify the emergency services.
48-volt battery
The indicator lamp lights up red while driving.
The following message is displayed:
Error: 48V power supply. Stop safely! Please
refer to the instruction manual.
There is a error in the 48V power supply.
1. Park the vehicle in a safe place.
2. Stop the engine and turn o the ignition.
3. Wait for a few seconds.
4. Switch ignition back on.
5. Start the engine.
If the lamp remains on, seek professional assis-
tance. CUPRA recommends going to a CUPRA
dealer or any SEAT dealership for this.
48-volt battery
When the vehicle is stopped, the warning lamp
lights up yellow and the following message is
displayed:
Error: 48V power supply. Do not start driv-
ing. Please refer to the instruction manual.
There is a error in the 48V power supply.
1. Park the vehicle in a safe place.
2. Stop the engine and turn o the ignition.
3. Wait for a few seconds.
4. Switch ignition back on.
5. Start the engine.
If the lamp remains on, seek professional assis-
tance. CUPRA recommends going to a CUPRA
dealer or any SEAT dealership for this.
48-volt battery
When the vehicle is stopped, the warning lamp
lights up yellow and the following message is
displayed:
372
Checking and relling levels
48V battery charge low. Start the engine or
refer to the owner's manual.
48V Battery state of charge warning.
1. Start the engine.
2. Stand in a safe place and leave the engine
running for a few minutes.
If the lamp remains on, seek professional assis-
tance. CUPRA recommends going to a CUPRA
dealer or any SEAT dealership for this.
If the engine cannot be started:
1. Switch the ignition o.
2. Use the Jump start ›››page340.
If the vehicle still won’t start, seek professio-
nal assistance. CUPRA recommends going to a
CUPRA dealer or any SEAT dealership for this.
Energy management
Optimisation of the starting ca-
pacity
Energy management controls the electrical
power distribution so that there is always
enough electrical power to start the engine.
If a vehicle with a conventional energy system
remains stationary for a long period of time,
the electrical devices, for example in the elec-
tronic ignition lock, discharge the battery. Un-
der certain circumstances, this can lead to a
lack of electrical power to start the engine.
In your vehicle, a smart energy management
system is responsible for distributing the elec-
trical energy. This clearly improves the starting
performance and service life of the battery.
The main functions incorporated in the power
management system are battery diagnosis,
residual current management and a dynamic
power management system.
Battery diagnostics
Battery diagnostics determine the status of the
battery on an ongoing basis. The battery volt-
age, current and temperature are monitored
for this purpose. This is used to determine the
battery's charge level and eiciency.
Residual current management system
The residual current management reduces en-
ergy consumption while the vehicle is station-
ary. When the ignition is switched o, it man-
ages the power supply to the various electrical
devices. In doing so, it takes into account the
battery diagnostic data.
With the ignition on and depending on the
battery's charge level, it disconnects electrical
devices one after the other to avoid over-dis-
charging the battery and to maintain starting
capacity.
Dynamic energy management system
Energy generated while driving is distributed
by the dynamic energy management system to
the electrical devices according to their energy
requirements. It also ensures that no more en-
ergy is consumed than is generated, thus en-
suring an optimal battery charge level.
Note
●
The energy management system cannot
override the limits imposed by the laws of
physics. Please note that the capacity and
service life of the battery are limited.
●
When there is a risk that the vehicle will not
start, the low battery charge level warning
lamp will be shown
›››page369.
Discharged battery
Maintaining starting capacity has top priority.
Battery strain is considerable on short jour-
neys, city driving and in the cold season of the
year.
In these situations, a lot of energy is required
but very little is generated. If the engine is
stopped and at the same time the electrical
devices are switched on, the battery can be-
come discharged to a critical point. In this case
energy is consumed without being generated
at the same time.
Checking and relling levels
373
Energy management
In these situations you will notice that the en-
ergy regulation system performs active energy
distribution adjustments.
Vehicle stationary for a long period of time
If you do not drive the vehicle for a few days
or weeks, adjustments will be made to reduce
consumption or the electrical devices will be
deactivated one by one. This reduces energy
consumption and the starting capacity is main-
tained for longer. Some convenience functions
may not be available under certain circumstan-
ces. The convenience functions will be availa-
ble again when the ignition is switched on and
the engine is started.
With the engine stopped
If you listen to the radio, for example, while
the engine is stopped, the battery will be dis-
charged.
If the energy consumption means there is a
risk that the engine will not start, a text will be
displayed in vehicles with a driver information
system.
This driver message indicates that the engine
must be started to recharge the battery.
With the engine running
The battery may discharge despite the fact
that energy is being generated while the vehi-
cle is in motion. This is particularly the case if
too little energy is generated and too much is
consumed at a time while the battery's level of
charge is not optimal.
To restore the energy balance, the devices that
consume the most energy are either tempora-
rily adjusted or deactivated. Heating systems,
in particular, consume a lot of energy. If you
notice, for instance, that the seat heating or
the rear window heater is not working, they
may have been temporarily switched o or
regulated to a lower heat output. These sys-
tems can be used again as soon as the energy
balance has been restored.
If necessary, you may also notice a slight
idling speed boost. However, this is normal and
should not cause you any concern. Boosting
the idling speed generates additional energy
and charges the battery.

Related Topics

Popular Owner Manuals