2024-2026 Cupra Terramar SUV Checking and refilling levels -> Cooling system User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Checking and refilling levels -> Cooling system for Your Cupra Terramar SUV First Generation (2024-2026)

354
Checking and relling levels
WARNING
Make sure that the bonnet is properly closed.
If it opens when driving, it can cause an acci-
dent.
NOTICE
In certain weather conditions, ice or snow
may build up between the bonnet and wind-
screen; do not force the bonnet open until
you are sure that there is no ice or snow, es-
pecially in the hinge area.
NOTICE
To avoid damage to the bonnet and to the
windscreen wiper arms, only open it when
the windscreen wipers are in place against
the windscreen.
Fluids and consumables
Introduction
All uids and consumables, such as engine
coolant or vehicle batteries, are subject to
continuous development. For this reason,
whenever a uid or consumable needs to be
replaced, please contact a specialist workshop.
CUPRA dealers always promptly receive infor-
mation about any modications.
WARNING
If unsuitable uids and consumables are used
or used improperly, accidents, injuries, burns
and severe poisoning can occur.
●
Only store operating uids in their original
containers, tightly closed.
●
Never store operating uids in empty food
cans, bottles or other empty containers, as
they could be ingested by somebody.
●
Keep all uids and consumables out of
reach of children.
●
Always read and observe the information
and warnings given on containers of operat-
ing uids.
●
When using products that emit harmful va-
pours, always work outdoors or in a well-ven-
tilated area.
NOTICE
Use only appropriate operating uids. Never
confuse operating uids. This could result in
serious malfunctions and engine damage!
For the sake of the environment
Leakages of operating uids can contami-
nate the environment. If any operating uid
leaks, collect it in an appropriate container
and dispose of it properly and in an environ-
mentally friendly manner.
Cooling system
Introduction
Only carry out work on the engine cooling sys-
tem yourself if you are familiar with the neces-
sary operations and the generally applicable
safety measures, and if you have the appro-
priate tools, equipment and operating uids.
Works performed inadequately could lead to
serious injuries . In this case, get a specialised
workshop to perform all the works. CUPRA rec-
ommends going to a specialised CUPRA dealer
or any SEAT dealership for this purpose.
WARNING
Engine coolant is toxic!
●
Only store coolant in its original container,
tightly closed and in a safe place.
●
Never store motor coolant in empty food
cans, bottles or other empty containers, as it
could be ingested by another person.
●
Always keep motor coolant out of reach of
children.
●
Ensure that the coolant uid additive per-
centage is correct, taking into account the
lowest ambient temperature expected in the
location where the vehicle is to be used.
Checking and relling levels
355
Cooling system
●
When the outside temperature is very low,
the coolant could freeze and the vehicle
could be immobilised. In this case, the heat-
ing would not work either and inadequately
dressed passengers could die of cold.
For the sake of the environment
Coolants and additives can contaminate the
environment. If any operating uid leaks out,
collect it and dispose of it properly and in an
environmentally friendly manner.
Coolant specications
The factory tted engine cooling system is l-
led with a mixture of specially treated water
and at least 40% coolant additive G12evo (TL-
VW 774 L).
Get information from a specialist workshop
about which coolant is suitable for your vehi-
cle. CUPRA recommends going to a specialised
CUPRA dealer or any SEAT dealership for this
purpose.
To protect the engine cooling system, the ad-
ditive percentage should always be at least
40%. If more antifreeze protection is required
for climatic reasons, the additive proportion
can be increased. However, it should only be
increased up to a maximum of 55%, otherwise
the antifreeze protection would be reduced
and the cooling eect would be impaired.
The G12evo (TL-VW 774 L) can be recognised
by its lilac colouring. This mixture of water
and additive not only provides antifreeze pro-
tection down to -25°C (-13°F), but also pro-
tects the light alloy parts of the cooling system
against corrosion, prevents limescale build-up
and considerably raises the boiling point of the
coolant.
When topping up the coolant, a mixture of
distilled water and at least 40% of the appro-
priate coolant additive should be used for opti-
mum corrosion protection ›››
page356.
WARNING
If the vehicle’s cooling system does not have
suicient antifreeze protection, the engine
could fail and this could result in serious in-
jury.
●
Ensure that the coolant uid additive per-
centage is correct, taking into account the
lowest ambient temperature expected in the
location where the vehicle is to be used.
●
When the outside temperature is very low,
the coolant could freeze and the vehicle
could be immobilised. In this case, the heat-
ing would not work either and inadequately
dressed passengers could die of cold.
NOTICE
Never mix the original additives for the
G12evo coolant (TL-VW 774 L) with motor
coolant uid not authorised by CUPRA.
●
If the uid in the expansion tank does not
have a pink colour (resulting from mixing the
lilac additive with distilled water), but is, for
example, brown, the suitable coolant may
have been mixed with another unsuitable
one. The coolant must be changed as soon as
possible if this is the case! Otherwise serious
malfunctions or damage to the engine and
the cooling system could occur!
For the sake of the environment
Motor coolant and its additives can pollute
the environment. If any operating uid leaks
out, collect it and dispose of it properly and
in an environmentally friendly manner.
356
Checking and relling levels
1
2
Coolant tank
✓ Valid for: hybrid vehicles.
Fig.223 Engine compartment: Coolant
tanks
Hybrid vehicles have 2 independent coolant
expansion tanks.
›››
Fig.223
Coolant expansion tank for the combus-
tion engine ›››Fig.224.
Coolant expansion tank for the high-volt-
age system ›››Fig.225.
Check and rell the coolant
Engine cooling uid
Fig.224 In the front compartment: coolant
expansion tank.
Preliminary steps
●
Park the vehicle on a rm, at surface.
●
Wait until the engine has fully cooled ››› .
●
Open the front bonnet ›››page351.
●
The engine coolant expansion tank can
be recognised by the symbol on the cap
›››Fig.224.
Check the level
When the vehicle is delivered (new vehicles),
the coolant may be above the marked area.
This is normal. It is not necessary to suck the
coolant out.
1. When the engine is cold, check the cool-
ant level using the side marking on the
expansion tank ›››Fig.224. The coolant
level should be between the marks.
2. If the level is below the minimum level
mark ( ) on the tank, top up with coolant.
When the engine is warm, the coolant level
may be slightly above the upper mark.
3. Do not add coolant if there is no more
coolant visible in the coolant expansion
tank ››› .
The coolant level cannot be checked accu-
rately on all models as the visibility of the uid
level in the coolant expansion tank may be ob-
structed. If the coolant level cannot be read
accurately, contact a qualied workshop.
When the motor coolant level is too low, the
coolant warning light comes on. In this case,
immediately seek assistance from specialist
personnel.
Checking and relling levels
357
Cooling system
Topping up the uid
If the coolant level is too low and there is no
workshop nearby, note the following:
1. Always protect your face, hands and arms
from hot coolant or steam by placing a
suitable cloth over the cap of the motor
coolant expansion tank.
2. Carefully unscrew the cap.
3. Only top up with fresh coolant according
to specications ›››page355.
Only top up with coolant if there is still
some coolant left in the expansion tank;
otherwise the engine could be damaged!
If you do not see any coolant in the ex-
pansion tank, do not continue driving and
seek specialist assistance.
4. If there is still some coolant left in the ex-
pansion tank, top up with coolant up to the
tank’s upper mark and check the level the
next day. If the level drops again, go to a
workshop and request a check of the cool-
ing system.
The coolant level must be between the
marks on the expansion tank ›››Fig.224.
Never exceed the top edge of the
marked area .
5. Screw the cap on tightly.
If engine coolant with the recommended
specications is not available in an emergency,
do not use any other coolant additive! In this
case, top up with distilled wateronly. Next, en-
sure that the recommended additive is topped
up as soon as possible in the correct propor-
tion ›››page355.
High voltage system coolant (valid for hybrid
vehicles)
Fig.225 In the front compartment: coolant
expansion tank.
Preliminary steps
●
Park the vehicle on a rm, at surface.
●
Wait for the high voltage system to cool down
››› .
●
Open the front bonnet ›››page351.
●
The high voltage system's coolant expansion
tank can be recognised by the symbol on the
cap
›››Fig.225.
Check the level
When the vehicle is delivered (new vehicles),
the coolant may be above the marked area.
This is normal. It is not necessary to suck the
coolant out.
1. Check the coolant level on the side marks
of the expansion tank when the coolant is
cold ›››
Fig.225. The coolant level should
be between the marks.
2. If the level is below the minimum level
mark ( ) on the tank, top up with coolant.
When the coolant is hot, the coolant level
may be slightly above the upper mark.
3. Do not add coolant if no coolant at all is
visible in the high voltage system ›››
coolant expansion tank.
The coolant level cannot be checked accu-
rately on all models as the visibility of the uid
level in the coolant expansion tank may be ob-
structed. If the coolant level cannot be read
accurately, contact a qualied workshop.
Topping up the uid
If the coolant level is too low and there is no
workshop nearby, note the following:
1. Always protect your face, hands and arms
from hot liquid coolant or steam by placing
a suitable cloth over the coolant expansion
tank cap.
2. Carefully unscrew the cap ›››
.
358
Checking and relling levels
3. Add only fresh coolant according to the
manufacturer's specication up to the up-
per level mark. After adding the coolant,
the coolant level must be between the
marks on the high voltage system coolant
expansion tank ›››Fig.225.
4. Close the cap tightly.
5. The next day, check the high voltage sys-
tem coolant level. If the level in the coolant
expansion tank has fallen below the mark
, have the cooling system checked by a
specialist workshop.
If in an emergency you do not have access to
coolant with the required specications, only
add distilled water in the rst instance. After-
wards, take the vehicle to a specialist workshop
as soon as possible to have the correct coolant
additive mixture restored.
WARNING
Steam and hot engine coolant can cause se-
vere burns.
●
Never open the front bonnet if you see
or hear steam or coolant escaping from the
front compartment. Always wait until you can
no longer see or hear steam or coolant es-
caping. Touching hot parts can result in skin
burns.
WARNING
Before opening the front bonnet, please
note the following:
●
Apply the electronic parking brake.
●
Always keep children away from the front
compartment and never leave them unat-
tended.
WARNING
When the engine is hot, its cooling system is
pressurised. Do not open the expansion tank
cap. Hot coolant may splash out and cause
severe burns and other injuries.
●
Turn the cap slowly and very carefully anti-
clockwise while pressing it down slightly.
●
Always protect your face, hands and arms
from the hot coolant and steam with a large
thick cloth.
NOTICE
Only use distilled water! Other types of wa-
ter contain chemical substances that could
cause signicant corrosion damage. If you
have added non-distilled water, have all of
the engine cooling system uid changed im-
mediately by a specialist workshop.
●
When adding coolant, do not ll above the
upper edge of the marked area ›››Fig.224,
›››Fig.225. Otherwise, when the temper-
ature rises the excess uid will be expelled
from the engine cooling system and could
cause damage.
●
If the system leaks a lot of coolant, only
rell once the motor has cooled down com-
pletely. If there is a signicant loss of coolant,
there may be leaks in the cooling system. Im-
mediately go to a specialist workshop to have
the system checked. This could result in en-
gine damage.
●
Do not add coolant if the expansion tank
is completely empty! Air may have got into
the cooling system. Do not continue driving
and seek assistance from specialist person-
nel. This could result in engine damage.
●
When changing the operating uids, make
sure that you pour the correct uids into the
correct ller necks. Using the wrong operat-
ing uids can lead to serious malfunctions
and engine damage.

Related Topics

Popular Owner Manuals