2024-2026 Cupra Terramar SUV Safety -> Transporting children safely User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Safety -> Transporting children safely for Your Cupra Terramar SUV First Generation (2024-2026)

62
Safety
●
The built-in coat hooks should be used
only for lightweight clothing. Do not leave
any heavy or sharp-edged objects in the
pockets. Please, do not hang clothes on coat
hangers.
●
The airbags provide protection for just one
accident; replace them once they have de-
ployed.
●
Any work on the head-protection airbag
system or removal and installation of the air-
bag components for other repairs (such as
removal of the roof lining) should only be
performed by a specialised workshop. Other-
wise, faults may occur during the airbag sys-
tem operation.
●
The side and head airbags are managed
through sensors located in the interior of the
front doors. To ensure the correct operation
of the side and curtain airbags neither the
doors nor the door panels should be modi-
ed in any way (e.g. tting loudspeakers). If
the front door is damaged, the airbag system
may not work correctly. All work carried out
on the front door must be done in a special-
ised workshop.
Transporting children
safely
Introduction
For safety reasons, as we have learned from
accident statistics, we recommend that chil-
dren under 12 years of age travel in the rear
seats. Depending on their age, height and
weight, children travelling in rear seats must
use a child seat or a seat belt. For safety rea-
sons, the child seat should be installed in the
rear seat, behind the front passenger seat or in
the centre back seat.
The laws of physics involved and the forces
acting in a collision also apply to children
›››
page48. But unlike adults, children do not
have fully developed muscle and bone struc-
tures. This means that children are subject to a
greater risk of injury.
To reduce the risk of injuries, children must
always use special child restraint systems when
travelling in the vehicle.
We recommend the use of child safety prod-
ucts from the Genuine Accessories Catalogue,
which includes systems for all ages (see
).
These systems have been especially de-
signed and approved and comply with the
UNECER129 (i-Size) regulation.
CUPRA recommends securing the child seats
shown on the website as described below:
●
Rear facing child seat (group 0+ / child
height 40-83cm):
–
ISOFIX and support leg (Britax Römer
Baby-Safe 3 i-SIZE + Flex Base i-SENSE).
●
Rear facing child seat (group 1 / child height
76-105cm):
–
ISOFIX AND Top Tether (Britax Römer TRI-
FIX 2 i-Size).
●
Forward facing child seat (group 2 / child
height 100-135cm):
–
Seat belt and ISOFIX (Britax Römer KIDFIX
i-Size).
You must also use the seat’s “Secure-Guard”
seatbelt connection point and adjust the
side impact protection system “SICT” (avail-
able on certain models), located in the seat
backrest. Adjust only the “SICT” closest to
the door. Please follow the child seat manu-
facturer's usage instructions.
●
Forward facing child seat (group 3 / child
height 125-150cm):
–
Seat belt and ISOFIX (Britax Römer KIDFIX
i-Size).
Group 3 can use the seat with backrest
or only the seat base without the backrest
(booster). The backrest of the child seat
has an adult seat belt guide and a headrest,
meaning that the seat with the backrest of-
fers better protection than boosters without
backrests. In addition, the child seat attach-
Safety
63
Transporting children safely
ment point for the “Secure-Guard” lap belt
must be used. CUPRA recommends the use
of child seats with backrests.
Follow the manufacturer's instructions and ob-
serve any statutory requirements when instal-
ling and using child seats. Always read and note
›››page64.
We recommend you always carry the manufac-
turer's Child Seat Instruction Manual together
with the on-board documentation.
Classication of child seats
Fig.37 Examples of child seats.
Use only child seats that are oicially approved
and suitable for the child.
These seats are subject to the ECE-R44 or
ECE-R129 standards. ECE-R stands for: Eco-
nomic Commission for Europe Regulation.
Child seats by weight group as per ECE-R44
and height as per ECE-R129
The child seats are grouped into 5 categories:
Group as per ECE-R44
Group 0 Up to 10 kg
Group 0+ Up to 13 kg
Group 1 From 9 to 18 kg
Group 2 From 15 to 25 kg
Group 3 From 22 to 36 kg
Child height as per ECE-R129
45-75 cm From birth to approx. 12
months.
45-87 cm From birth to approx. 4 years.
61-105 cm approx. 4 months to 4 years
100-135 cm approx. 4 to 8 years
125-150 cm approx. 4 years to 12 years
Child seats that have been tested and ap-
proved under the ECE R44 or ECE-R129 stand-
ards bear the ECE-R44 or ECE-R129 test marks
on the seat (the letter E in a circle with the test
number below it).
Follow the manufacturer's instructions and ob-
serve any statutory requirements when instal-
ling and using child seats.
We recommend that you always include the
manufacturer's Child Seat Instruction Manual
together with the on-board documentation.
CUPRA recommends you use child seats from
the Original Accessories Catalogue. These
child seats have been designed and tested for
use in our vehicles. You can nd the right child
seat for your model and age group at our deal-
ers.
Child seats by approval category
Child seats may have the approval category of
universal, semi-universal, vehicle specic (all
according to the ECE-R44 standard) or i-Size
(according to the ECE-R129 standard).
●
Universal: child seats with universal approval
can be installed in all vehicles. There is no need
to consult any list of models. In the case of
universal approval for ISOFIX, the child seat is
additionally provided with a Top Tether belt.
●
Semi-universal: semi-universal approval, in
addition to the standard requirements of uni-
versal approval, requires safety devices to lock
the child seat, which require additional test-
ing. Child seats with semi-universal approval
include a list of vehicle models for which they
can be installed.
64
Safety
●
Vehicle-specic: vehicle-specic approval
requires a dynamic test of the child seat for
each vehicle model separately. Child seats with
vehicle-specic approval also include a list of
vehicle models for which they can be installed.
●
i-Size: child seats with i-Size approval must
meet the requirements prescribed in the ECE-
R 129 standard in relation to installation and
safety. Child seat manufacturers can tell you
which seats have i-Size approval for this vehi-
cle.
Fitting and using child seats
Fig.38 Airbag sticker: on the passenger
side sunshade blind.
Fig.39 Airbag sticker: on the rear frame of
the passenger side door.
Warnings about tting a child seat
Take the following general warnings into ac-
count if you are going to t a child seat. They
are valid for all child seats regardless of their
attachment system.
●
Please read and follow the child seat manu-
facturer's operating instructions.
●
The child seat should preferably be tted to
the rear seat behind the front passenger seat
so that the child can exit the vehicle on the
pavement side.
●
Set the height of the seat belt such that
it adapts to the child seat naturally, without
twisting. The lowest position of the seat belt
height regulator must be used with rear-facing
child seats.
●
To correctly use a child seat in the back, the
front backrest must be adjusted so that there
is no contact with the child seat in the back if
it is rear facing. In the case of forward-facing
restraint systems, the front backrest must be
adjusted so that there is no contact with the
child's feet.
●
For a correct assembly of the child's seat on
the rear seats, adjust or dismount the head-
rest, in order to prevent contact with the seat.
●
If a semi-universal type seat is to be installed,
in which the method of attachment to the car
is through the seat belt and support bracket,
it should never be installed in the central rear
seat as the ground clearance is lower than in
other places and the support bracket will not
allow the seat to remain suiciently stable.
Important information about the front pas-
senger airbag
A sticker with important information about the
passenger airbag is located on the passenger's
sunshade blind and/or on the passenger side
door frame ›››Fig.38.
Read and always observe the safety informa-
tion included in the following chapters:
●
Safety distance with respect to the passenger
airbag ›››
page54.
●
Objects between the passenger and the pas-
senger side airbag ››› in Front airbags on
page58.
Safety
65
Transporting children safely
The passenger side front airbag, when ena-
bled, is a serious risk for a rear-facing child
since the airbag can strike the seat with such
force that it can cause serious or fatal injuries.
Children up to 12 years old should always travel
on the rear seat.
Therefore we strongly recommend that you
transport children on the rear seats. This is the
safest location in the vehicle. Alternatively, the
front passenger airbag can be disabled with a
key-operated switch ›››page58. When trans-
porting children, use a child seat suitable for
the age and size of each child ›››page63.
WARNING
●
If a child seat is secured to the front pas-
senger seat, the risk to the child of sustaining
critical or fatal injuries in the event of an ac-
cident increases.
●
An inating front passenger airbag can
strike the child seat and throw it with great
force against the door, the roof or the back-
rest.
●
Never install a rear-facing child seat on the
front passenger seat unless the front passen-
ger airbag has been disabled. Risk of poten-
tially fatal injuries to the child! However, if
necessary, the front passenger airbag must
be deactivated›››
page58.
●
For those vehicles that do not include a key
lock switch to deactivate the airbag, the vehi-
cle must be taken to a technical service. Do
not forget to reconnect the airbag when an
adult wants to sit in the front passenger seat.
●
Never allow a child to be transported in a
vehicle without being properly secured, or
to stand up or kneel on a seat while travel-
ling. In an accident, the child could be ung
through the vehicle, causing possibly fatal in-
juries to themselves and to the other vehicle
occupants.
●
Never leave a child alone in the child seat
or in the vehicle.
●
Children who are less than 1.50m tall must
not wear a normal seat belt without a child
seat, as this could cause injuries to the ab-
dominal and neck areas during a sudden
braking manoeuvre or in an accident.
●
When a child seat is mounted in the rear
seats, the door's child lock should be activa-
ted ›››page112.
Attachment systems
Depending on the country, dierent attach-
ment systems are used for safely installing child
seats.
Attachment systems overview
●
ISOFIX: ISOFIX is a standardised attachment
system allowing quick and safe attachment of
child seats in the vehicle. ISOFIX attachment
establishes a rigid connection between the
child seat and the car body.
The child seat has two rigid attachment clips,
called connectors. These connectors are t-
ted into the ISOFIX attachment rings found
between the seat cushion and the backrest
of the vehicle's back seat (on the sides). ISO-
FIX attachment systems are used mainly in Eu-
rope ›››page66. If necessary, ISOFIX at-
tachment may have to be supplemented with a
Top Tether belt or a support bracket.
●
Automatic three-point seat belt. Whenever
possible, it is preferable to attach the child
seats with the ISOFIX system rather than at-
taching them with an automatic three-point
seat belt ›››page71.
Additional attachment:
●
Top Tether: the Top Tether belt is guided
over the back of the rear seat and attached to
an anchor point with a hook. Anchor points are
located at the back of the rear seat backrest on
the luggage compartment side ›››page69.
The rings for retaining the Top Tether belt are
marked with an anchor symbol.
●
Support bracket: some child seats rest on
the oor of the vehicle with a support bracket.
The support bracket prevents the child seat
from tipping forward in the event of impact.
Child seats tted with a support bracket should
66
Safety
only be used in the passenger seat and side
rear seats ››› . For the assembly of this type
of seat you should also consult the list of ap-
proved vehicles for this assembly, available in
the instructions for child restraint systems.
Recommended systems for attaching child
seats
CUPRA recommends attaching child seats as
follows:
●
Baby carriers or rear facing child seats:
ISOFIX and support bracket or i-Size.
●
Forward-facing child seats: ISOFIX and Top
Tether.
WARNING
Incorrect use of the support bracket can
cause serious or fatal injury.
●
Make sure the support bracket is correctly
and safely installed.
●
When the child seat base is supporting the
weight of the child, the support leg must not
be in the air or propped up with objects. Also
ensure that the base of the child seat rests
permanently on the surface of the vehicle's
seat. The support leg of the child seat must
not lift the base of the child seat o the sur-
face of the vehicle's seat.
Securing a child seat with the ISO-
FIX or i-Size system
The marking of ISOFIX or i-Size anchor points
depends on the equipment and the country in
question.
To understand the compatibility of the ISOFIX
or i-Size systems in the vehicle, check the table
below.
Safety
67
Transporting children safely
Vehicle ISOFIX/i-Size positions
Child seat Child seat orientation
Size class /
ISOFIX class
Front passenger seat
Rear side
seat
Rear cen-
tral seat
airbag ena-
bled
a)
airbag disabled
b)
Group 0: up to 10kg Rear facing E / R1 X IL IL X
Group 0+: up to 13kg Rear facing
E / R1 X IL IL X
D / R2 X IL IL X
C / R3 X IL IL X
Group I: 9 to 18kg
Rear facing
D / R2 X IL IL X
C / R3 X IL IL X
Forward-facing
B / F2 IL, IUF X IL, IUF X
B1 / F2X IL, IUF X IL, IUF X
A / F3 IL, IUF X IL, IUF X
Group II: 15 to 25kg
c)
Forward-facing -- / -- IL X IL X
Group III: 22 to 36kg
c)
Forward-facing -- / -- IL X IL X
i-Size child seat
Rear facing -- / R2 X IUF IUF X
Forward-facing -- / B2, F2X IUF X IUF X
Booster Forward-facing -- / B2, B3 IB X IB X
a)
For forward-facing child seats with the airbag activated, the passenger seat must be positioned as far away from the airbag as possible, while ensuring that the
upper attachment point of the vehicle seatbelt is behind the child seat.
b)
For rear-facing child seats with the airbag deactivated, seats without height adjustment should be moved to their rearmost position, and seats with height
adjustment should be moved to their rearmost and lowest position.
c)
Installation in front seats requires reclining the backrest.
●
Size class: The indication of class according to size corresponds to the authorised body weight for the child seat. In child seats with universal or
semi-universal approval, the class according to size is indicated on the ECE approval label. The indication of class according to size is stated on the
corresponding child seat.
68
Safety
1)
Not available in all markets.
●
IUF: Suitable for ISOFIX / i-Size child restraint systems with “universal” approval, approved for use in this weight group.
●
IL: Suitable for certain ISOFIX child restraint systems that can be for the specic vehicle, restricted or semi-universal categories. Take the child seat
manufacturer's vehicle list into account.
●
IB: Seat suitable for installing an ISOFIX forward-facing group 2/3 booster seat as well as an i-size forward-facing child seat for children with a height
of 100 to 150cm.
●
X: Position not suitable for ISOFIX or i-Size child restraint systems in this weight group or size class.
Securing the child seat with the ISOFIX or
i-Size system
Fig.40 Rear seat: location of the ISOFIX or
i-Size securing rings.
Fig.41 Front passenger seat: location of
the i-Size securing rings.
Fig.42 Rear seats: tting a child seat with
the ISOFIX system.
You must follow the child seat manufacturer's
instructions.
The location of the ISOFIX or i-Size anchor
points is indicated by a symbol ›››
Fig.40 ,
›››
Fig.41
1)
. In some vehicles, the rings are
secured to the seat frame and, in others, they
are secured to the rear oor.
Safety
69
Transporting children safely
1)
Not available in all markets/versions.
●
If necessary, remove the protective caps
from the ISOFIX or i-Size anchor points.
●
Press the child seat onto the ISOFIX or iSize
securing rings until it is heard to engage se-
curely ›››Fig.42. If the child seat is equipped
with Top Tether anchor points, secure it to the
corresponding ring ›››page69. Follow the
child seat manufacturer’s instructions.
●
Pull on both sides of the child seat to ensure
that it is properly anchored.
Child seats with the ISOFIX or i-Size and Top
Tether attachment system can be purchased
from technical services.
WARNING
The securing rings are designed only for use
with ISOFIX or i-Size and Top Tether system
child seats.
●
Never secure other child seats that do not
have ISOFIX, i-Size or Top Tether systems, or
safety belts or any other objects to the secur-
ing rings – as this can result in potentially
fatal injuries.
●
Ensure that the child seat is correctly se-
cured to the ISOFIX or i-Size rings and the
Top Tether.
Top Tether securing belts
Fig.43 Rear part of the rear seats: Top
Tether belt anchor.
Fig.44 Rear of front passenger seat
backrest: Top Tether belt anchor (not
available in all markets/versions).
Child seats with a Top Tether system are tted
with an additional belt for fastening to an an-
chor point in the vehicle. This anchor point
is located on the rear of the rear seat back-
rest and of the front passenger seat backrest
1)
(identied with the symbol
) and provides
better retention ›››Fig.43, ›››Fig.44.
The objective of this system is to reduce for-
ward movements of the child seat in a head-on
collision, to reduce the risk of injuries that may
be caused to the child’s head by impacting
against any element of the inside of the vehi-
cle.
Use of Top Tether on rear-facing child re-
straints
Currently, there are very few rear-facing child
restraints with Top Tether. The car seat manu-
facturer's instructions for proper installation of
the Top Tether should be read carefully and
followed.
70
Safety
Locking the tether belt
Fig.45 Rear seats: adjustment and
assembly according to the Top Tether belt.
Fig.46 Front passenger seat: adjustment
and assembly according to the Top Tether
belt.
●
Follow the manufacturer's instructions to de-
ploy the child seat Top Tether retaining belt
●
Rear seats: position the belt under the head-
rest (according to the instructions of the seat
itself, lift or remove the headrest if necessary)
›››Fig.45.
Passenger seat: pass the belt over the built-in
headrest ›››Fig.46.
●
Slide the belt and secure it properly with the
anchor on the rear seat backrest ›››Fig.43 ,
›››Fig.44.
●
Tighten the belt securely according to the
manufacturer’s instructions.
Release the tether belt
●
Loosen the belt according to the manufac-
turer’s instructions.
●
Press the lock and release it from the anchor
bracket.
WARNING
Installing safety seats incorrectly will increase
the risk of injury in the event of a collision.
●
Never attach the tether belt to a fastening
hook in the luggage compartment.
●
Never attach or secure luggage or other
items to the lower anchor points (ISOFIX) or
Top Tether anchor points.
WARNING
Child restraint anchors are designed to sup-
port the loads of properly adjusted child
restraint systems. Under no circumstances
should they be used to attach adult seat
belts, harnesses or other items or equipment
to the vehicle.
Safety
71
Transporting children safely
Fitting a child seat using the seat
belt
If you want to t a universal approval category
(U) child seat in your vehicle, you must check
that the seat is approved for your vehicle.
You will nd any necessary information on the
child seat’s orange ECE approval label.
The following table shows the dierent tting
options:
Child seat Child seat orientation
Front passenger seat
Rear side seat
Rear central
seat
a)
Airbag enabled
b)
Airbag deactivated
c)
Group 0 up to 10kg Rear facing X U U U
Group 0+ up to 13kg Rear facing X U U U
Group I 9 to 18kg
Rear facing X U U U
Forward-facing U X U U
Group II 15 to 25kg Forward-facing U X U U
Group III 22 to 36kg Forward-facing U X U U
Child seats as per ECE-
R129
Rear facing X U U U
Forward-facing U X U U
X: Position not compatible for the installation of seats in this conguration.
U: Position suitable for the installation of seats in this conguration.
a)
Do not use semi-universal seats that use the vehicle’s seat belt and a support leg as a securing system on the centre rear seat.
b)
Move the front passenger seat as far as possible from the airbag. Ensure that the upper attachment point of the vehicle’s seat belt remains behind the child seat.
c)
Seats without height adjustment should be placed in their rearmost position. Seats with height adjustment should be placed in their rearmost and highest
position.

Related Topics

Popular Owner Manuals