2020-2024 DS 9 4 Door Practical information User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Practical information for Your DS 9 4 Door First Generation (2020-2024)

141  
07  
Practical information  
accompanied by the message and the audible  
signal. When driving, this message and audible  
signal are repeated with increasing frequency as  
the fuel level drops towards 0.  
►ꢀ To open the filler flap, press the flap opening  
button or press the rear edge of the filler flap  
(depending on version).  
Compatibility of fuels  
Rechargeable hybrid vehicles  
Petrol fuels conforming to the EN228 standard  
containing up to 5% and 10% ethanol respectively.  
You must refuel as soon as possible to avoid  
running out of fuel.  
After pressing the button, it may take a  
few minutes for the filler flap to open.  
If the flap becomes stuck, press and hold the  
button for more than 3 seconds.  
The only petrol fuel additives authorised  
for use are those that meet the B715001  
standard.  
A small arrow by the warning lamp  
indicates which side of the vehicle the  
fuel filler flap is located on.  
The filler cap is built into the flap.  
►ꢀ Select a pump that delivers the correct fuel  
type for the vehicle's engine (see a reminder label  
on the inside of the filler flap).  
Stop & Start  
Travelling abroad  
Never refuel with the engine in STOP  
mode; you must switch off the ignition.  
Certain fuels could damage your vehicle’s engine.  
In certain countries, the use of a particular fuel  
may be required (specific octane rating, specific  
trade name, etc.) to ensure correct operation of  
the engine.  
►ꢀ Insert the filler nozzle and push it in as far as  
possible before starting to refuel (to minimise the  
risk of splashing).  
Refuelling  
Any addition of fuel must be in quantities of at  
least 10 litres, in order to be registered by the fuel  
gauge.  
►ꢀ Fill the tank.  
Do not continue past the 3rd cut-off of the nozzle;  
For all additional information, consult a dealer.  
as this may cause malfunctions.  
►ꢀ Push the filler flap to close it.  
Opening the filler flap may create a noise caused  
by an inrush of air. This vacuum is entirely normal,  
resulting from the sealing of the fuel system.  
To refuel in complete safety:  
Refuelling  
Fuel tank capacity: approximately 60 litres  
(Petrol) or 43 litres (Rechargeable hybrid).  
Reserve level: approximately 6 litres.  
The vehicle is fitted with a catalytic converter,  
which helps to reduce the level of harmful  
emissions in the exhaust gases.  
For petrol engines, you must use unleaded fuel.  
The filler neck is narrower, allowing only unleaded  
petrol nozzles to be inserted.  
►ꢀ Always switch off the engine.  
Low fuel level  
When the low fuel level is reached, this  
warning lamp lights up on the instrument  
panel, accompanied by the display of a message  
and an audible signal. When it first comes on,  
about 6 litres of fuel remain.  
If you have put in the wrong fuel for the  
vehicle, you must have the fuel tank  
drained and filled with the correct fuel before  
starting the engine.  
Until sufficient fuel is added, this warning lamp  
appears every time the ignition is switched on,  
142  
07  
Practical information  
Rechargeable hybrid vehicles  
traction battery, connectors, orange cables  
and other components visible from the interior  
or exterior) is strictly prohibited - risk of  
severe burns or potentially fatal electric shock  
(short-circuit/electrocution)!  
You must immediately contact the emergency  
services, informing them that the incident  
involves a rechargeable hybrid vehicle.  
If the filler flap is accidentally closed  
before refuelling, it cannot be opened  
manually. Restart the engine and move the  
vehicle a few metres before pressing the  
filler flap opening button again.  
When washing  
Contact a dealer or a qualified workshop.  
Before washing the vehicle, always check  
that the charging flap is closed correctly.  
Never wash the vehicle while the battery is on  
charge.  
Rechargeable hybrid  
system  
High-pressure washing  
To avoid damaging the electrical  
components, it is expressly prohibited to  
use high-pressure washing in the engine  
compartment or under the body.  
Do not use a pressure greater than 80 bar  
when washing the bodywork.  
Electrical system  
The electrical circuit of the rechargeable hybrid  
system is identified by orange cables and its  
components are marked with this symbol:  
This label is intended solely for use by  
firefighters and maintenance services in  
the event of any work on the vehicle.  
No other person must touch the device shown  
on this label.  
Never allow water or dust to enter the  
connector or charging nozzle - risk of  
electrocution or fire!  
In the event of an accident or impact to  
the vehicle’s underbody  
In these situations, the electrical circuit or the  
traction battery can be seriously damaged.  
Stop as soon as it is safe to do so and switch  
off the ignition.  
Never connect / disconnect the charging  
nozzle or cable with wet hands - risk of  
electrocution!  
The rechargeable hybrid powertrain uses  
a voltage of between 240 V and 400 V.  
This system may be hot both when the ignition  
is on and after switching it off.  
Contact a dealer or a qualified workshop.  
Traction battery  
The Li-ion (Lithium-ion) traction battery stores the  
electrical energy needed to propel the vehicle.  
It is located under the rear seats.  
Comply with the warning messages shown on  
the labels, particularly inside the charging flap.  
In the event of exposure to a fire  
Immediately exit and evacuate all  
passengers from the vehicle. Never attempt to  
fight the fire yourself - risk of electrocution!  
In the event of a problem  
The traction battery's range varies depending  
on the type of driving, the route, the use of  
All work on or modifications to the  
vehicle’s electrical system (including the  
143  
07  
Practical information  
thermal comfort equipment and the ageing of its  
components.  
Charging cables, sockets and  
chargers  
1. Deferred charging activation button  
2. Indicator lamp confirming that the nozzle is  
locked into the charging connector.  
Fixed red: nozzle correctly positioned and  
locked.  
The traction battery ageing depends on  
several factors, such as climatic  
The traction battery can be charged using several  
different types of cables.  
conditions and the distance travelled.  
The charging cables supplied with the vehicle  
are compatible with the electrical installations of  
the country of sale. If you are travelling abroad,  
refer to the following tables to check the  
compatibility of local electrical installations with  
the charging cables.  
Flashing red: nozzle incorrectly positioned or  
locking not possible.  
In the event of damage to the traction  
battery  
3. Charging connector  
4. Light guides  
It is strictly prohibited to work on the vehicle  
yourself.  
Do not touch liquids coming from the traction  
battery; in the event of contact between the  
skin and these products, wash abundantly  
with water and contact a doctor as soon as  
possible.  
Contact a dealer or a qualified workshop to obtain  
the appropriate charging cable(s).  
Identification labels on charging sockets/  
connectors  
Identification labels are affixed to the vehicle,  
charging cable and charger to inform the user  
about which device needs to be used.  
The meaning of each identification label is as  
follows:  
Status of light  
guides  
Meaning  
Charging flap  
The charging flap is located on the rear left-hand  
Fixed white  
Welcome lighting when flap  
is opened  
side of the vehicle.  
Fixed blue  
Deferred charging  
Charging  
Flashing green  
Fixed green  
Fixed red  
Charging complete  
Malfunction  
In case of impact, even light, against the  
charging flap, do not use it.  
Do not dismantle or modify the charging  
connector - risk of electrocution and/or fire!  
Contact a dealer or a qualified workshop.  
144  
07  
Practical information  
Identification label  
Location  
Configuration  
TYPE 2  
Power type/Voltage range  
Charging connector (vehicle side)  
AC  
C
C
< 480 Vrms  
Charging socket (charger side)  
TYPE 2  
AC  
< 480 Vrms  
Types of charging  
Cable type  
Compatibility  
Specifications  
Mode 2 charging cable with integrated control unit  
Conventional electrical socket A (depending  
Charge limited to a maximum of 8 A.  
on country).  
"Green'Up" type socket B.  
Charge limited to a maximum of 16 A.  
Identification label C on the charging connector  
(vehicle side).  
145  
07  
Practical information  
Cable type  
Compatibility  
Specifications  
Mode 3 charging cable  
Accelerated charging unit socket A.  
Charge limited to a maximum of 32 A.  
Wallbox accelerated charging unit B.  
Identification labels C on the charging connector  
(vehicle side) and D on the socket (charger side).  
The estimated charging time is indicated  
on the instrument panel when the vehicle  
is connected. It may vary depending on various  
factors such as the outside temperature or the  
quality of the electricity supply.  
Domestic charging cable (mode 2)  
It is essential to avoid damaging the cable  
and to keep it intact.  
Control unit (mode 2)  
In the event of damage, do not use it and  
contact a dealer or a qualified workshop to  
replace it.  
If the outside temperature is below -10°C, it is  
recommended to connect the vehicle as soon  
as possible as the charging time may increase  
significantly. The traction battery may not  
charge fully.  
Accelerated charging unit (mode 3)  
Do not dismantle or modify the  
accelerated charging unit - risk of  
electrocution and/or fire!  
To find out how it is used, please refer to the  
accelerated charging unit's user instructions.  
146  
07  
Practical information  
POWER  
1. Incorrect use of this charging cable may  
result in fire, property damage and serious  
injury or death by electrocution!  
13. Never plug the cable into the wall socket (or  
unplug it) with wet hands.  
Green: electrical connection established;  
charging can begin.  
14. Do not force the connector if it is locked into  
the vehicle.  
CHARGE  
2. Always use a correctly earthed power socket,  
protected by a 30 mA residual current device.  
3. Always use an electrical socket protected  
by a circuit-breaker appropriate for the  
electrical circuit’s current rating.  
Flashing green: charging in progress or  
temperature pre-conditioning activated.  
Fixed green: charging complete.  
Control unit label - State of indicator lamps  
State of the indicator  
lamp  
FAULT  
Red: fault; charging not permitted or must  
be stopped immediately. Check that everything  
is connected correctly and that the electrical  
system is not faulty.  
4. The weight of the control unit must not be  
borne by the electrical socket, plug and  
cables.  
Off  
On  
5. Never use this charging cable if it is defective  
or in any way damaged.  
If the indicator lamp does not go off, contact a  
dealer or a qualified workshop.  
6. Never attempt to repair or open this charging  
cable. It contains no repairable parts -  
replace the charging cable if it is damaged.  
7. Never immerse this charging cable in water.  
8. Never use this charging cable with an  
extension cable, a multi-plug socket,  
a conversion adaptor or on a damaged  
electrical socket.  
Upon plugging the charging cable into a domestic  
socket, all of the indicator lamps come on briefly.  
If no indicator lamps come on, check the domestic  
socket's circuit-breaker:  
Flashing  
– If the circuit-breaker has tripped, contact a  
professional to check that the electrical system  
is compatible and/or carry out any necessary  
repairs.  
9. Do not unplug the plug from the wall as a  
means of stopping charging.  
– If the circuit-breaker has not tripped, stop  
using the charging cable and contact a dealer or a  
qualified workshop.  
10. Immediately stop charging, by locking and  
then unlocking the vehicle using the remote  
control key, if the charging cable or wall  
socket feel burning hot to the touch.  
11. This charging cable includes components  
liable to cause electrical arcing or sparks. Do  
not expose to flammable vapours.  
Control unit label - Recommendations  
Refer to the handbook before use.  
12. Only use this charging cable with DS  
AUTOMOBILES vehicles.  
147  
07  
Practical information  
POWER  
CHARGE  
FAULT  
Symbol  
Description  
Not connected to the power supply or power is not  
available from the infrastructure.  
The control unit is currently performing a self-test.  
(green)  
(green)  
(green)  
(green)  
(red)  
Connected only to the infrastructure or to the  
infrastructure and to the Electric Vehicle (EV) but no  
charging in progress.  
Connected to the power supply and to the Electric  
Vehicle (EV).  
The EV is on charge or in a temperature pre-  
conditioning sequence.  
(green)  
(green)  
Connected to the power supply and to the Electric  
Vehicle (EV).  
The EV is waiting for charging or the charging of the  
EV is completed.  
(green)  
Control unit malfunction. No charging allowed.  
If an error indicator reappears after a manual reset,  
the control unit must be checked by a dealer before  
the next charge.  
(red)  
(red)  
The control unit is in diagnostic mode.  
(green)  
(green)  
148  
07  
Practical information  
Manual reset procedure  
The control unit can be reset by simultaneously disconnecting the charging connector and the wall socket.  
Then, reconnect the wall socket first. For more information, refer to the handbook.  
Lounge mode  
Charging the traction  
Wearers of pacemakers or equivalent  
devices should consult a doctor to enquire  
about any applicable precautionary measures, or  
contact the manufacturer of their implanted  
electronic medical device to check that it is  
guaranteed to operate in an environment  
compliant with the ICNIRP guidelines.  
When the vehicle is connected, it is  
battery (Rechargeable  
hybrid)  
possible to switch on the ignition and use  
certain functions such as the audio and  
telematics system and the air conditioning  
system for several hours.  
For a full charge, follow the charging  
procedure without interrupting it, until it stops  
automatically. Charging may be performed either  
immediately (by default) or deferred.  
Deferred charging is set via the touch  
screen or the MyDS App application.  
When the vehicle is connected, the following  
information is displayed on the instrument panel:  
– Status of the battery (%).  
If in doubt, during charging, do not remain inside  
or near the vehicle, near the charging cable or the  
charging unit, even for a short time.  
Vehicle in storage for more than 1 month  
Discharge the traction battery down to 2  
or 3 bars on the charge level indicator on the  
instrument panel.  
Before charging  
Do not connect the charging cable.  
Always park the vehicle in a place with  
temperatures between -10°C and 30°C  
(parking in a place with extreme temperatures  
can damage the traction battery).  
Refer to the Accessory battery (Rechargeable  
hybrid) section for the battery disconnection  
procedure.  
Depending on the context:  
►ꢀ Have a professional check that the  
electrical system to be used complies with  
applicable standards and is compatible with  
the vehicle.  
– Remaining range (miles or km).  
– Estimated charging time (calculation may take  
a few seconds).  
►ꢀ Have a professional electrician install  
a dedicated domestic power socket or  
accelerated charging unit (Wallbox)  
compatible with the vehicle.  
– Charging speed (kW/h).  
After the instrument panel has been put into  
standby mode, this information can be displayed  
again by unlocking the vehicle or opening a door.  
Use the charging cable supplied with the  
vehicle.  
Precautions  
Rechargeable hybrid vehicles have  
It is also possible to monitor the charging  
progress using the MyDS App application.  
For more information on Remote functions,  
refer to the corresponding section.  
For more information, contact a dealer or a  
qualified workshop.  
been developed in accordance with the  
recommendations for maximum electromagnetic  
field limits established by the ICNIRP  
(International Commission on Non-Ionizing  
Radiation Protection - 1998 Guidelines).  
During charging  
As a safety measure, the engine will not  
start if the charging cable is plugged into  
149  
07  
Practical information  
the connector on the vehicle. A warning is  
displayed on the instrument panel.  
While charging is in progress, unlocking the  
vehicle will cause the charging to stop.  
If no action is taken on one of the openings  
(door or boot) or on the charging nozzle, the  
vehicle will lock again after 30 seconds and  
charging will resume automatically.  
Never work under the bonnet:  
Domestic charging (mode 2)  
Accelerated charging (mode 3)  
►ꢀ Follow the accelerated charging unit (Wallbox)  
user instructions.  
– Some areas remain very hot, even an hour  
after charging ends - risk of burns!  
►ꢀ Remove the protective cover from the  
charging nozzle.  
– The fan may start at any time - risk of cuts or  
strangulation!  
►ꢀ Insert the nozzle into the vehicle's charging  
connector.  
The start of charging is confirmed by the flashing  
of the green light guides in the flap.  
If this is not the case, charging has not  
started; restart the procedure ensuring that all  
connections are properly established.  
The red indicator lamp in the flap comes on to  
indicate that the nozzle is locked.  
►ꢀ First, connect the charging cable from the  
control unit to the domestic socket.  
When the connection is made, all of the indicator  
lamps on the control unit light up, then only the  
POWER indicator lamp remains on in green.  
►ꢀ Remove the protective cover from the  
charging nozzle.  
After charging  
Check that the charging flap is closed.  
Do not leave the cable connected to the  
domestic power socket - risk of short-circuit  
or electrocution in the event of contact with or  
immersion in water!  
►ꢀ Insert the nozzle into the vehicle's charging  
connector.  
Disconnection  
Charging procedure  
The start of charging is confirmed by the flashing  
of the green light guides in the flap and the  
flashing of the CHARGE indicator lamp in green on  
the control unit.  
Connection  
►ꢀ Before charging, check that the gear selector  
is in mode P and the ignition is off, otherwise  
charging is impossible.  
If this is not the case, charging has not started;  
restart the procedure, ensuring that all of the  
connections are properly established.  
The red indicator lamp in the flap comes on to  
indicate that the nozzle is locked.  
►ꢀ Press on the rear of the charging flap to open  
it and check that there are no foreign bodies on  
the vehicle's charging connector.  
Before disconnecting the nozzle from the  
charging connector:  
►ꢀ If the vehicle is locked, unlock it.  
The light guides in the flap come on white.  
150  
07  
Practical information  
►ꢀ If the vehicle is unlocked, lock it and then  
unlock it.  
►ꢀ In the Energy touch screen menu,  
select the Charge page.  
We recommend having them fitted by a dealer  
or a qualified workshop.  
►ꢀ Set the charging start time.  
►ꢀ Press OK.  
If not fitted by a dealer, they must still be  
fitted in accordance with the Manufacturer's  
instructions.  
If selective unlocking of the doors is  
activated, press the unlocking button on  
the remote control twice to disconnect the  
nozzle.  
The setting is saved in the system.  
With DS CONNECT RADIO or NAVIGATION  
You can also programme the deferred  
charging function at any time from a  
smartphone via the MyDS App application.  
For more information on Remote functions, refer  
to the corresponding section.  
Important: with a motorised boot and  
its Hands-Free Tailgate Access function, if  
a towing device is fitted outside the dealer  
network, it is essential to visit a dealer or a  
qualified workshop to recalibrate the detection  
system. Risk of malfunction of the Hands-Free  
Tailgate Access function.  
The red indicator lamp in the flap goes out to  
confirm that the nozzle is unlocked.  
►ꢀ Within 30 seconds, remove the charging  
nozzle.  
Activation  
Domestic charging (mode 2)  
Certain driving or manoeuvring aid functions  
are automatically deactivated while an  
approved towing system is in use.  
►ꢀ Connect the vehicle to the desired charging  
equipment.  
The end of charging is confirmed when the  
green CHARGE indicator lamp on the control unit  
comes on fixed and the green light guides in the  
flap come on fixed.  
►ꢀ Press this button in the flap within one  
minute to activate deferred charging  
(confirmed by the light guides coming on in blue).  
For more information about driving with a  
towing device fitted to a trailer and associated  
with the Trailer stability assist, refer to the  
corresponding section.  
►ꢀ After disconnection, replace the protective  
cover over the nozzle and close the charging flap.  
►ꢀ Disconnect the control unit's charging cable  
from the domestic socket.  
Towing device  
Load distribution  
Comply with the maximum authorised  
towable weight, as indicated on your  
vehicle's registration certificate, on the  
manufacturer's label and in the Technical data  
section of this guide.  
Accelerated charging (mode 3)  
►ꢀ Distribute the load in the trailer so that  
the heaviest items are as close as possible to  
the axle, and the nose weight approaches the  
maximum permitted without exceeding it.  
Air density decreases with altitude, thus reducing  
engine performance. The maximum towable  
load must be reduced by 10% per 1,000 metres of  
altitude.  
The end of charging is confirmed by the  
accelerated charging unit (Wallbox) and when the  
green light guides in the flap come on fixed.  
►ꢀ After disconnection, replace the nozzle on to  
the charging unit and close the charging flap.  
If using accessories attached to the  
towing device (e.g. bicycle carriers, tow  
boxes):  
Deferred charging  
– Comply with the maximum authorised nose  
weight.  
Settings  
Use genuine towing devices and wiring  
harnesses approved by the Manufacturer.  
With NAVIGATION  
151  
07  
Practical information  
– Do not transport more than 4 conventional  
bicycles or 2 electric bicycles.  
To recharge the battery, avoid repeatedly or  
Energy economy mode  
continuously restarting the engine.  
This system manages the duration of use of  
certain functions, in order to conserve a sufficient  
level of charge in the battery with the ignition off.  
After switching off the engine and for a maximum  
cumulative period of around 30 minutes, you can  
continue to use functions such as the audio and  
telematics system, dipped beam headlamps or  
courtesy lamps.  
When loading bicycles onto a bicycle carrier  
on a towball, be sure to place the heaviest  
bicycles as close as possible to the vehicle.  
A flat battery prevents the engine from  
starting.  
For more information on the 12 V battery, refer  
to the corresponding section.  
Observe the legislation in force in the  
country where you are driving.  
Very cold climate screen  
(Depending on country of sale)  
Vehicle equipped with motorised boot  
with Hands-Free Tailgate Access function  
To avoid unintentionally opening the boot while  
operating the towing device:  
Selecting the mode  
A confirmation message is displayed when  
energy economy mode is entered, and the active  
functions are placed on standby.  
This removable device prevents the accumulation  
of snow around the radiator cooling fan.  
It consists of two elements to be attached to the  
front bumper.  
– Deactivate this function in advance in your  
vehicle's configuration menu.  
If a telephone call is in progress at the  
time, it will be maintained for around 10  
minutes via the audio system’s hands-free  
system.  
– Or remove the electronic key from the  
recognition zone, with the boot closed.  
In case of difficulty with installation/  
removal  
Contact a dealer or a qualified workshop.  
Load reduction mode  
This system manages the use of certain functions  
according to the level of charge remaining in the  
battery.  
Before any operation, ensure that the  
engine is off and the cooling fan has  
stopped.  
Exiting the mode  
These functions are automatically reactivated the  
next time the vehicle is used.  
When the vehicle is being driven, the load  
reduction function temporarily deactivates  
certain functions, such as the air conditioning  
and the heated rear screen.  
It is essential to remove them when:  
– the outside temperature exceeds 10°C.  
– recovery is in progress.  
To restore the use of these functions immediately,  
start the engine and let it run:  
– For less than 10 minutes, to use the equipment  
for approximately 5 minutes.  
– the speed is above 75 mph (120 km/h).  
The deactivated functions are reactivated  
automatically as soon as conditions permit.  
– For more than 10 minutes, to use the equipment  
for approximately 30 minutes.  
Let the engine run for the specified duration to  
ensure that the battery charge is sufficient.  
152  
07  
Practical information  
►ꢀ Apply the parking brake and position any  
wheel chocks under the wheels to prevent  
movement of the vehicle.  
Snow chains  
In wintry conditions, snow chains improve  
traction as well as the behaviour of the vehicle  
when braking.  
Roof bars  
As a safety measure and to avoid  
►ꢀ Fit the snow chains following the instructions  
provided by the manufacturer.  
damaging the roof, it is essential to use  
transverse roof bars approved for your vehicle.  
Observe the instructions on fitting and use  
contained in the guide supplied with the roof  
bars.  
►ꢀ Move off gently and drive for a few moments,  
without exceeding 31 mph (50 km/h).  
►ꢀ Stop the vehicle and check that the snow  
chains are correctly tightened.  
Snow chains must be fitted only to the  
front wheels. They must never be fitted to  
"space-saver" type spare wheels.  
Observe the legislation in force in your  
country relating to the use of snow chains  
and maximum authorised speeds.  
Maximum load distributed over the roof  
bars, for a loading height not exceeding  
40 cm: 80 kg.  
It is strongly recommended that you  
practise fitting the snow chains on a level  
and dry surface before setting off.  
As this value may change, please verify the  
maximum load quoted in the guide supplied  
with the roof bars.  
Use only the chains designed to be fitted to the  
type of wheel fitted to the vehicle:  
Avoid driving with snow chains on roads  
that have been cleared of snow to avoid  
damaging the vehicle's tyres and the road  
surface. If the vehicle is fitted with alloy  
wheels, check that no part of the chain or its  
fixings is in contact with the wheel rim.  
If the height exceeds 40 cm, adapt the speed  
of the vehicle to the profile of the road to avoid  
damaging the roof bars and the fixings on the  
vehicle.  
Tyre size  
215/60 R17  
235/50 R18  
235/45 R19  
235/40 R20  
Chain type  
POLAIRE XP9 120  
POLAIRE PSGB 110  
POLAIRE PSGB 110  
Be sure to refer to national legislation in order  
to comply with the regulations for transporting  
objects that are longer than the vehicle.  
Rechargeable hybrid vehicles  
The use of snow chains is only authorised  
on the front wheels.  
Cannot be fitted with  
chains  
For more information on snow chains, contact a  
dealer or a qualified workshop.  
The driving mode selector must be on the 4WD  
position (depending on version).  
Installation tips  
►ꢀ To fit the snow chains during a journey, stop  
the vehicle on a flat surface at the side of the  
road.  
153  
07  
Practical information  
Remove the roof bars once they are no longer  
needed.  
Rechargeable hybrid vehicles  
Fitting directly to the roof  
Before any work is carried out under the  
bonnet, it is essential to switch off the ignition  
and disconnect the charging connector nozzle  
if it is connected, check that the READY  
indicator lamp is off on the instrument panel  
and wait 4 minutes - risk of serious injury!  
Sunroof  
You must only attach the transverse bars to the  
four fixing points located on the roof frame. These  
points are concealed by the vehicle doors when  
the doors are closed.  
The location of the interior bonnet release  
lever prevents the bonnet being opened  
when the left-hand front door is closed.  
Do not operate the sunroof when using  
roof bars - risk of major damage!  
The roof bar fixings have a stud which must be  
inserted into the opening of each fixing point.  
When the engine is hot, handle the  
exterior safety catch with care (risk of  
burns), using the protected area.  
When the bonnet is open, take care not to  
damage the safety catch.  
Bonnet  
Stop & Start  
Recommendations  
Before doing anything under the bonnet,  
you must switch off the ignition to avoid any  
risk of the engine restarting automatically.  
Take care with objects or clothing that could  
be caught in the blades of the cooling fan  
or in certain moving components - risk of  
strangulation and serious injury!  
Distribute the load uniformly, taking care  
to avoid overloading one of the sides.  
Arrange the heaviest part of the load as close  
as possible to the roof.  
Do not open the bonnet under very windy  
conditions.  
Secure the load firmly.  
Cooling of the engine when stopped  
The engine cooling fan may start after the  
engine has been switched off.  
Drive gently: the vehicle will be more  
susceptible to the effects of side winds and its  
stability may be affected.  
Take care with objects or clothing that could  
be caught in the blades of the fan!  
Regularly check the security and tight  
fastening of the roof bars, at least before each  
trip.  
154  
07  
Practical information  
Opening  
Closing  
4. Battery/Fuses  
5. Remote earth point (-)  
6. Fusebox  
►ꢀ Lower the bonnet and release it near the end  
of its travel.  
►ꢀ Check the locking.  
7. Air filter  
8. Engine oil filler cap  
9. Engine oil dipstick  
Because of the presence of electrical  
equipment under the bonnet, it is strongly  
recommended that exposure to water (rain,  
washing, etc.) be limited.  
Checking levels  
Check all of the following levels regularly in  
accordance with the manufacturer's service  
schedule. Top them up if required, unless  
otherwise indicated.  
Engine compartment  
►ꢀ From the inside: pull the control lever, located  
on the left below the dashboard, towards you.  
The engine shown here is an example for  
illustrative purposes only.  
The locations of the following components may  
vary:  
If a level drops significantly, have the  
corresponding system checked by a dealer or a  
qualified workshop.  
– Air filter.  
The fluids must comply with the  
manufacturer's requirements and with  
the vehicle's engine.  
– Engine oil dipstick.  
– Engine oil filler cap.  
Depending on version, the battery may be  
protected by a cover.  
Take care when working under the  
bonnet, as certain areas of the engine  
may be extremely hot (risk of burns) and the  
cooling fan could start at any time (even with  
the ignition off).  
Petrol engine  
►ꢀ From the outside: lift the safety catch and  
raise the bonnet.  
Two bonnet struts open the bonnet and hold it  
open.  
1. Screenwash fluid reservoir  
2. Engine coolant reservoir  
3. Brake fluid reservoir  
155  
07  
Practical information  
Used products  
Checking using the dipstick  
Use of non-recommended oil may invalidate  
your warranty in the event of engine failure.  
For the location of the dipstick, please refer  
to the illustration of the corresponding engine  
compartment.  
Avoid prolonged contact of used oil or  
fluids with the skin.  
Topping up the engine oil level  
Most of these fluids are harmful to health and  
very corrosive.  
►ꢀ Grasp the dipstick by its coloured grip and pull  
it out completely.  
For the location of the engine oil filler cap, please  
refer to the corresponding engine compartment  
illustration.  
►ꢀ Wipe the end of the dipstick using a clean, lint-  
free cloth.  
Do not discard used oil or fluids into  
sewers or onto the ground.  
►ꢀ Add oil in small quantities, avoiding any spills  
on engine components (risk of fire).  
►ꢀ Wait a few minutes before checking the level  
again using the dipstick.  
Empty used oil into the containers reserved  
for this purpose at a dealer or a qualified  
workshop.  
►ꢀ Top up the level if necessary.  
►ꢀ After checking the level, carefully screw the  
oil filler cap back on and replace the dipstick in  
its tube.  
Engine oil  
The level is checked, with the engine  
having been switched off for at least 30  
minutes and on level ground, either using the oil  
level indicator in the instrument panel when the  
ignition is switched on (for vehicles equipped with  
an electric gauge), or using the dipstick.  
It is normal to top up the oil level between two  
services (or oil changes). It is recommended that  
you check the level, and top up if necessary, every  
3,000 miles (5,000 km).  
►ꢀ Reinsert the dipstick and push fully down,  
then pull it out again to visually check the oil level:  
the correct level is between marks A (max) and  
B (min).  
The oil level indication displayed on the  
instrument panel when the ignition is  
switched on is not valid for 30 minutes  
following an addition of oil.  
Do not start the engine if the level is:  
– above mark A: contact a dealer or a qualified  
workshop.  
– below mark B: top up the engine oil  
immediately.  
Brake fluid  
The level of this fluid should be close to the  
"MAX" mark. If not, check the brake pads  
for wear.  
Oil grade  
In order to maintain the reliability of the  
engine and emissions control system,  
never use additives in the engine oil.  
Before topping up or changing the engine  
oil, check that the oil is suitable for your engine  
and complies with the recommendations in  
the service schedule supplied with the vehicle  
(or available from your dealer or qualified  
workshop).  
To know how often the brake fluid should be  
replaced, refer to the manufacturer's servicing  
schedule.  
Clean the cap before removing it to refill.  
Use only DOT4 brake fluid from a sealed  
container.  
156  
07  
Practical information  
appropriate for the temperature conditions  
must be used in order to protect the system's  
components (pump, tank, ducts, jets).  
For more information on the precautions  
to take before any work on the 12 V  
Engine coolant  
It is normal to top up this fluid between  
battery, refer to the corresponding section.  
two services.  
The check and top-up must only be done with the  
engine cold.  
Filling with pure water is prohibited in all  
circumstances (risk of freezing, limescale,  
etc.).  
Versions equipped with Stop & Start are  
fitted with a 12 V lead-acid battery with  
special technology and specifications.  
Its replacement should be carried out only by a  
dealer or a qualified workshop.  
A level of coolant that is too low risks causing  
major damage to the engine; the coolant level  
must be close to the "MAX" mark without ever  
going above it.  
Checks  
If the level is close to or below the "MIN" mark, it  
is essential to top it up.  
Unless otherwise indicated, check these  
components in accordance with the  
manufacturer's service schedule and according to  
your engine.  
Air filter  
When the engine is hot, the temperature of the  
coolant is regulated by the fan.  
Depending on the environment and the use  
of the vehicle (e.g. dusty atmosphere, city  
As the cooling system is pressurised, wait at least  
one hour after switching off the engine before  
carrying out any work.  
driving), change it twice as often, if necessary.  
Otherwise, have them checked by a dealer or a  
qualified workshop.  
Passenger compartment filter  
In order to avoid the risk of scalding if you need to  
top up in an emergency, wrap a cloth around the  
cap and unscrew the cap by two turns to allow the  
pressure to drop.  
Only use products recommended by the  
Manufacturer or products of equivalent  
quality and specification.  
Depending on the environment and the use  
of the vehicle (e.g. dusty atmosphere, city  
driving), change it twice as often, if necessary.  
In order to optimise the operation of  
components as important as those in the  
braking system, the Manufacturer selects and  
offers very specific products.  
Once the pressure has dropped, remove the cap  
and top up to the required level.  
A clogged passenger compartment filter  
can adversely affect air conditioning  
system performance and generate undesirable  
odours.  
Screenwash fluid  
Top up to the required level when  
12 V battery  
necessary.  
Oil filter  
The battery does not require any  
Fluid specification  
maintenance.  
Change the oil filter each time the engine  
Check regularly that the terminals are correctly  
tightened (versions without quick-release  
terminals) and that the connections are clean.  
oil is changed.  
The fluid must be topped up with a pre-mixed  
product.  
In winter (temperatures below zero), a fluid  
containing an anti-freeze agent which is  
157  
07  
Practical information  
For more information on the Electric  
reading and have an adverse effect on road  
Automatic gearbox  
parking brake, refer to the corresponding  
holding.  
The gearbox does not require any  
section.  
Fitting different tyres on the front and rear axles  
can cause the ESC to mistime.  
maintenance (no oil change).  
Always mark the direction of rotation on the tyres  
that will be stored when fitting winter or summer  
tyres. Store them in a cool, dry place and away  
from direct exposure to the sun's rays.  
Winter or 4-seasons tyres can be identified  
by this symbol on their sidewalls.  
Brake pads  
Wheels and tyres  
The inflation pressure of all tyres,  
including the spare wheel, must be  
checked on "cold” tyres.  
Brake wear depends on the style of driving,  
particularly in the case of vehicles used in  
town, over short distances. It may be necessary to  
have the condition of the brakes checked, even  
between vehicle services.  
The pressures indicated on the tyre pressure label  
are valid for "cold" tyres. If you have driven for  
more than 10 minutes or more than 6 miles (10  
kilometres) at over 31 mph (50 km/h), add 0.3 bar  
(30 kPa) to the values indicated on the label.  
Unless there is a leak in the circuit, a drop in the  
brake fluid level indicates that the brake pads are  
worn.  
Shock absorbers  
It is not easy for drivers to detect when  
shock absorbers are worn. Nevertheless,  
the shock absorbers have a major impact on road  
holding and braking performance.  
After washing the vehicle, moisture, or in  
wintry conditions, ice can form on the  
brake discs and pads: braking efficiency may  
be reduced. Gently dab the brakes to dry and  
defrost them.  
Under-inflation increases energy  
consumption. Non-compliant tyre  
For your safety and driving comfort, it is important  
to have them regularly checked by a dealer or a  
qualified workshop.  
pressures cause tyres to wear prematurely and  
have an adverse effect on the vehicle's road  
holding - risk of accident!  
Driving with worn or damaged tyres reduces the  
braking and road holding performance of the  
vehicle. Regularly check the condition of the tyres  
(tread and sidewalls) and rims as well as the  
presence of the valve caps.  
Timing and accessory kits  
Brake disc wear  
For information on checking brake disc  
wear, contact a dealer or a qualified  
workshop.  
The timing and accessory kits are used  
from the time the engine is started until it  
is switched off. It is normal for them to wear over  
time.  
When the wear indicators no longer appear set  
back from the tread, the depth of the grooves is  
less than 1.6 mm; replace the tyres as soon as  
possible.  
A faulty timing or accessory kit can damage  
the engine, rendering it unusable. Observe the  
recommended replacement frequency, stated in  
distance travelled or time elapsed, whichever is  
reached first.  
Electric parking brake  
This system does not require any routine  
servicing. However, in the event of a  
problem, do not hesitate to have the system  
checked by a dealer or a qualified workshop.  
Using different size wheels and tyres from those  
specified can affect the lifetime of tyres, wheel  
rotation, ground clearance, the speedometer  
158  
07  
Practical information  
Reverting to normal operation  
"hands-free" function (Hands-Free Tailgate  
Access).  
Free-wheeling  
►ꢀ While depressing the brake pedal, restart the  
engine.  
In certain situations, it is necessary to put the  
vehicle into free-wheeling mode (e.g. towing, on  
a rolling road, automatic car wash (Wash mode),  
rail or sea transport).  
When using a pressure washer, keep the jet  
nozzle at a minimum distance of 30 cm from  
the vehicle (particularly when cleaning areas  
containing chipped paint, sensors or seals).  
Promptly clean up any stains containing  
chemicals liable to damage the vehicle's  
paintwork (including tree resin, bird droppings,  
insect secretions, pollen and tar).  
Keyless Entry and Start  
You must not depress the brake pedal  
while switching the ignition on again, then  
switching it off. If you do, the engine will start,  
requiring you to restart the procedure.  
The procedure varies according to the type of  
gearbox and parking brake.  
With EAT8 automatic gearbox  
and electric parking brake  
Depending on the environment, clean the  
vehicle frequently to remove salty deposits  
(in coastal areas), soot (in industrial areas)  
and mud/salts (in wet or cold areas). These  
substances can be highly corrosive.  
Contact a dealer or a qualified workshop for  
advice on removing stubborn stains requiring  
special products (such as tar or insect  
removers).  
Advice on care and  
maintenance  
/
Release procedure  
General recommendations  
Observe the following recommendations to avoid  
►ꢀ With the vehicle stationary and the engine  
running, select mode N and switch off the  
ignition.  
damaging the vehicle.  
Within 5 seconds:  
Exterior  
►ꢀ Switch on the ignition again.  
►ꢀ While depressing the brake pedal, move the  
push selector forwards or backwards to confirm  
mode N.  
Preferably, have paint touch-ups performed by  
a dealer or a qualified workshop.  
Never use a high-pressure jet wash in the  
engine compartment - risk of damaging  
the electrical components!  
Interior  
►ꢀ While depressing the brake pedal, press the  
control lever to release the parking brake.  
►ꢀ Release the brake pedal, switch off the  
ignition.  
Do not wash the vehicle in bright sunshine or  
extremely cold conditions.  
When washing the vehicle, never use a  
water hose or high-pressure jet to clean  
the interior.  
When washing the vehicle in an automatic  
roller-brush car wash, be sure to lock the  
doors and, depending on version, move the  
electronic key away and deactivate the  
Liquids carried in cups or other open  
containers can spill, presenting a risk of  
damage to the instruments and controls and  
the controls located on the centre console. Be  
vigilant!  
If the 5-second time limit is exceeded, the gearbox  
engages mode P; it is then necessary to restart  
the procedure.  
159  
07  
Practical information  
To clean instrument panels, touch screens  
or other displays, wipe gently with a soft,  
dry cloth. Do not use products (e.g. alcohol,  
disinfectant) or soapy water directly on these  
surfaces - risk of damage!  
Use a high-flow hose (temperature  
between 25°C and 40°C).  
Place the jet of water perpendicular to the  
surface to be cleaned.  
Rinse the vehicle with demineralised water.  
Bodywork  
High-gloss paint  
Leather  
Leather is a natural product. Appropriate regular  
care is essential for its durability.  
It must be protected and nourished using a  
specific leather product, to keep it supple and  
preserve its original appearance.  
Do not use abrasive products, solvents,  
petrol or oil to clean the bodywork.  
Never use an abrasive sponge to clean  
stubborn stains - risk of scratching the  
paintwork!  
Do not clean leather using unsuitable  
cleaning agents such as solvents,  
Do not apply polish in strong sunshine, or to  
plastic or rubber parts.  
detergents, petrol or pure alcohol.  
When cleaning items partly made from leather,  
take care not to damage the other materials  
with the specific leather product.  
Use a soft cloth and soapy water or a pH  
neutral product.  
Gently wipe the bodywork with a clean  
microfibre cloth.  
Before cleaning greasy stains or liquids,  
quickly mop up any surplus.  
Apply polish with the vehicle clean and dry.  
Comply with the instructions for use stated on  
the product.  
Before cleaning, wipe off any residues liable  
to scuff the leather, using a cloth that has  
been dampened with demineralised water and  
thoroughly wrung out.  
Decals  
Clean leather using a soft cloth moistened  
with soapy water or a pH-neutral product.  
Dry with a soft, dry cloth.  
(Depending on version)  
Do not use a high-pressure washer to  
clean the vehicle - risk of damaging or  
detaching the decals!  

Related Topics

Compatibility of fuels Refuelling Rechargeable hybrid system Charging cables, sockets and chargers Charging the traction battery (Rechargeable hybrid) Towing device Energy economy mode Very cold climate screen Snow chains Roof bars Bonnet Engine compartment Checking levels Checks 12 V battery Wheels and tyres Free-wheeling Advice on care and maintenance

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot