Get Getting To Know Your Vehicle -> Climate Control System Guide for Fiat 124 Spider 2 Door Second Generation (2016-2020)

Lane Change Assist

Leaving Home Light

System

Headlamp Leveling

System — If Equipped

Move the lever halfway toward the

direction of the lane change (until the

indicator flashes) and hold it there. It will

return to the off position when released.

The Leaving Home Light System turns

the headlights on when the unlock

button on the key fob is pushed while

away from the vehicle.

On some models, the angle of the

headlights will be automatically adjusted

when turning on the headlights.

Three-Flash Turn Signal

Adjusting The Headlight

When Abroad

Activation

After releasing the turn signal lever, the

turn signal indicator flashes three times.

With the ignition cycled to OFF, and the

headlight switch is in the

Dipped headlights are adjusted for

driving in the country where the vehicle

was originally purchased.

or

The operation can be cancelled by

moving the lever in the direction

opposite to which it was operated.

position, the headlights will

illuminate when the unlock button on

the key fob is pushed, and the vehicle

receives the signal.

When travelling in countries with

opposite driving direction, to avoid

flashing the drivers on the other side of

the road, you need to cover areas of

the headlight. For this operation contact

an authorized dealer.

The three-flash turn signal function can

be turned on or off using the

personalization function in the radio.

The headlights turn off after

30 seconds.

Adaptive Front Lighting

System (AFS) — If

Equipped

The following lights turn on when the

Leaving Home Light System is

operated: low beams/parking lights/tail

lights/license plate lights.

This system directs the main headlight

beams and adapts it to the driving

conditions around bends and turns,

continuously and automatically.

Operation of the Leaving Home Light

System can be turned on or off through

the Connect system.

The system directs the headlight beam

to illuminate the road in the best way,

taking into account the speed of the

vehicle, the bend or corner angle and

the speed of steering.

When the lock button on the key fob

is pushed, and the vehicle receives the

signal, the headlights turn off.

When the headlight switch is in a

position other than

headlights turn off.

The Adaptive Front Lighting System is

automatically activated when the

vehicle is started.

or

, the

42

OFF: stop

When the wiper lever is in the AUTO

position and the ignition is cycled ON,

the wipers may move automatically in

the following cases:

WINDSHIELD

WIPERS / WASHER

AUTO: auto control operation

— or LO: low speed operation

= or HI: high speed operation

Adjusting Rain Sensor Sensitivity

Windshield Wipers And

Washer

If the windshield above the rain

sensor is touched or wiped with a cloth.

The windshield wiper/washer lever is

located on the right side of the steering

wheel. The ignition must be cycled ON

before using these features.

If the windshield is struck with a hand

or other object from either outside or

inside the vehicle.

The sensitivity of the rain sensor can be

adjusted by rotating the switch on the

wiper lever.

Windshield Wipers

From the center position (normal),

rotate the switch downward for higher

sensitivity (+) (faster response) or rotate

it upward for less sensitivity (-) (slower

response).

Activate the windshield wipers by

pushing the wiper lever up or down.

Warning!

With Intermittent Wiper

Keep hands and scrapers clear of the

windshield when the wiper lever is in the

AUTO position and the ignition is cycled

ON, as fingers could be pinched or the

wipers and wiper blades damaged when

the wipers activate automatically.

Set the lever to the intermittent position

and choose the interval timing by

rotating the center switch.

Switch positions:

or MIST: operation while

pushing the lever upward

If you are going to clean the windshield,

be sure the wipers are turned off. This

is important when clearing ice and

snow.

OFF: stop

--- or INT: intermittent operation

— or LO: low speed operation

= or HI: high speed operation

With Auto-Wiper Control

Turning the auto-wiper lever from the

OFF to the AUTO position while driving

activates the windshield wipers once,

after which they operate according to

the rainfall amount.

05030101-122-001

Windshield Wiper Lever

1 — Rain Sensor Adjustment

When the wiper lever is in the AUTO

position, the rain sensor will sense the

amount of rainfall on the windshield and

turns the wipers on or off automatically

(off/intermittent/low speed/high speed).

The auto-wiper control may not operate

when the rain sensor temperature is

about 14 °F (–10 °C) or lower, or about

185 °F (85 °C) or higher.

Note: Do not shade the rain sensor by

placing a sticker or a label on the

windshield. Otherwise the rain sensor

will not operate correctly.

Switch positions:

or MIST: operation while

pulling up lever

43

If the windshield is coated with water

repellent, the rain sensor may not be

able to sense the amount of rainfall

correctly and auto-wiper control may

not operate properly.

With the wiper lever in the OFF,

intermittent, or AUTO position, the

wipers will operate continuously until

the lever is released.

CLIMATE CONTROL

SYSTEM

Operating Tips

The air conditioning system will only

operate with the engine running.

If dirt or debris (such as ice or debris

containing salt water) adheres to the

windshield above the rain sensor or if

the windshield is iced, it could cause

the wipers to move automatically.

Warning!

To prevent the battery from being

discharged while the engine is off, do

not leave the Blower Control Knob on

for extended periods of time.

Sudden loss of visibility through the

windshield could lead to a collision. You

might not see other vehicles or other

obstacles. To avoid sudden icing of the

windshield during freezing weather, warm

the windshield with defroster before and

during windshield washer use.

However, if the wipers cannot remove

this ice, dirt or debris, the auto-wiper

control will stop operation. In this case,

set the wiper lever to the low speed

position or high speed position for

manual operation, or remove the ice,

dirt or debris by hand to restore the

auto-wiper operation.

To improve system efficiency, clear all

obstructions (leaves, snow and ice)

from the hood and the air inlet in the

grille.

Use the air conditioning system to

defog the windows and dehumidify the

air.

If the fluid level is normal and the

washer does not work, contact an

authorized dealer.

Recirculation mode should be used

when driving through tunnels, while in a

traffic jam, or when you would like to

quickly cool the interior.

If the auto-wiper lever is left in the

AUTO position, the wipers could

operate automatically from the effect of

strong light sources, electromagnetic

waves, or infrared light because the rain

sensor uses an optical sensor.

Use the outside air position for

ventilation or windshield defrosting.

If the vehicle has been parked in direct

sunlight during hot weather, open the

windows to let warm air escape, and

then run the air conditioning system.

It is recommended that the auto-wiper

lever be turned to the OFF position

other than when driving the vehicle

under rainy conditions.

To keep the internal parts lubricated

and the system running smoothly, run

the air conditioner about ten minutes at

least once a month.

The auto-wiper control functions can be

turned off.

04110109-115-001

Windshield Washer Nozzles

Windshield Washer

Have the air conditioner checked before

the weather gets hot. A lack of

refrigerant may make the air conditioner

less efficient. The refrigerant

Pull the wiper/washer lever rearward

and hold it to spray washer fluid onto

the windshield.

44

specifications are indicated on a label (A

or B depending on the market)

attached to the inside of the engine

compartment. Check the label before

refilling the refrigerant. If the wrong type

of refrigerant is used, it could result in a

serious malfunction of the air

Vent Operation

Adjusting The Vents

To adjust the direction of air flow, move

the vent adjustment knob.

Note: When using the air conditioner in

humid conditions, fog may blow from

the vents. This is a result of humid air

being suddenly cooled and does not

indicate a system malfunction.

conditioner. For details, contact an

authorized dealer.

Center Vents (Driver) and Side

Vents

06010201-033-001

Side Air Vents

Center and side vents are located on

the dashboard.

Air vent open/close: the air vents can

be fully opened and closed by using

knob 1 (A = open / B = close).

Air flow direction adjustment: use

knob 1 to adjust the center vents to the

desired position.

06010100121001

Label Location

Caution!

06010201-033-666

Operating the Side Air Vents

The system uses a coolant that is

1 — Air Vent Knob

A — Open Position

B — Closed Position

compatible with the laws in force in the

countries where the vehicle is sold, R134a

or R1234yf (indicated on a specific plate in

the engine compartment). The use of other

coolants affects the efficiency and

condition of the system. Also the

compressor coolants used must be

compatible with the indicated coolant.

45

Center Vents (Front Passenger)

Center vents are located on the

dashboard.

Air vent open/close: use the Center

Vent tab 1 to open/close the center

vents (A = open / B = close).

Air flow direction adjustment: use the

Center Vent tab 1 to adjust the center

vents to the desired position.

06010201-121-777

Operating The Central Air Vent

1 — Center Vent Tab

A — Open Position

B — Closed Position

06010201-121-001

Central Air Vent

46

Airflow Mode

06010202-121-002

Airflow Locations

1 — Fixed Upper Air Diffuser

2 — Adjustable Side Air Vents

3 — Adjustable Center Air Vent

4 — Floor Vents

47

Manual Climate Control System

With MAX A/C function

06010300-122-002

Manual Climate Controls With MAX A/C

1 — Temperature Control Knob

2 — Blower Control Knob

3 — Mode Selector Knob

4 — Rear Window Defrost Button

5 — Air Recirculation Button

6 — A/C Button

48

Controls

flow from the floor vents is less than

that of the position.

Note:

Before opening the convertible top,

1 – Temperature Control Knob

4 – Rear Window Defrost Button

make sure the Rear Window Defrost

Button is turned off. Otherwise, the

heat generated from the defroster

could damage the convertible top and

the internal material.

This dial controls the interior

temperature of the vehicle.

The Rear Window Defrost Button clears

fog and frost from the rear window. The

ignition must be on to use the defroster.

Turn it clockwise for hotter temperatures

and counterclockwise for colder

temperatures.

Push the button to turn on the Rear

Window Defroster. The Rear Window

Defroster operates for about

15 minutes and then turns off

automatically. The button LED will

illuminate when the defroster is

operating.

This defroster is not designed for

melting snow. If there is an

accumulation of snow on the rear

window, remove it before using the

defroster.

MAX A/C – If Equipped: When the

Mode Selector Knob is set to or

,

the Blower Control Knob is in a position

other than 0, and the temperature

control knob is in the maximum cold

position, the Recirculation Button will

activate and the A/C will turn on

Mirror Defroster — If Equipped: To

turn on the mirror defroster, turn the

ignition ON and push the Rear Window

Defroster Button.

To turn off the Rear Window Defroster

before the end of 15 minutes, push the

button again.

automatically. If A/C is not desired,

press the A/C Button to turn it off.

2 – Blower Control Knob

5 – Air Recirculation Button

Caution!

The blower has seven speeds. Turn the

knob clockwise to increase blower speed

or counterclockwise to decrease blower

speed.

Push the Air Recirculation Button to

select between outside air and

recirculated air positions.

Failure to follow these cautions can cause

damage to the heating elements:

Recirculated Air Position: (LED on)

Outside air is shut off when this position

has been activated. Use this position

when going through tunnels, driving in

congested traffic (high engine exhaust

areas), or when quick cooling of the

vehicle is desired.

Use care when washing the inside of the

rear window. Do not use abrasive window

cleaners on the interior surface of the

window. Use a soft cloth and a mild

washing solution, wiping parallel to the

heating elements. Labels can be peeled

off after soaking with warm water.

3 – Mode Selector Knob

Turn the Mode Selector Knob to select

the air flow mode.

The mode selector dial can be set at

the intermediate positions (●) between

each mode.

Outside Air Position: (LED off)

Outside air is allowed to enter the

cabin. Use this mode for ventilation or

windshield defrosting.

Set the knob to an intermediate

position if you want to split the air flow

between the two modes.

Do not use scrapers, sharp instruments,

or abrasive window cleaners on the interior

surface of the window.

For example, when the Mode Selector

Knob is at the intermediate position (●)

Keep all objects a safe distance from

the window.

between the and

positions, air

49

Note: Do not use the Outside Air

If the windshield fogs up easily, set the

Mode Selector Knob to the position.

Note:

If the air conditioner is used while

driving up large hills or in heavy traffic,

monitor the Engine Coolant

Temperature Warning Light to see if it

is illuminated or flashing. The air

conditioner may cause engine

overheating in these situations. If the

warning light is illuminated or flashing,

turn the air conditioning off

Position in cold or rainy weather is

dangerous as it will cause the windows

to fog up. Your vision will be hampered,

which could lead to a serious accident.

If cooler air is desired at face level, set

the Mode Selector Knob to the

position and adjust the Temperature

Control Knob to maintain comfort.

6 – A/C Button

The floor vents will blow warmer air

while the side air vents will blow cooler

air (except when the temperature

control dial is set at the maximum hot

or cold position).

Push the A/C Button to turn on the air

conditioner.

The LED on the switch will illuminate

when the Blower Control Knob is in any

position except the OFF position.

immediately.

Cooling (With Air

Conditioner)

When maximum cooling is desired,

set the Temperature Control Knob to

the extreme cold position, push the Air

Recirculation Button to activate the

recirculated air position, and then turn

the fan control dial fully clockwise.

Push the button again to turn off the air

conditioner.

Note: The air conditioner may not

function when the outside temperature

approaches 32 °F (0 °C).

Proceed as follows:

1. Set the Mode Selector Knob to the

position.

Heating

If warmer air is desired at floor level,

set the Mode Selector Knob to the

position, and adjust the

Temperature Control Knob to maintain

comfort.

2. Set the Temperature Control Knob

to the cold position.

Proceed as follows:

1. Set the Mode Selector Knob to the

position.

3. Set the Blower Control Knob to the

desired speed.

2. Set the Air Recirculation Button to

the outside air position.

4. Turn on the air conditioner by

pushing the A/C Button.

The floor vents will blow warmer air

while the side air vents will blow cooler

air (except when the temperature

control dial is set at the maximum hot

or cold position).

3. Set the Temperature Control Dial to

the hot position.

5. After cooling begins, adjust the

Blower Control Knob and Temperature

Control Knob as needed to maintain

comfort.

4. Set the Blower Control Knob to the

desired speed.

5. If dehumidified heating is desired,

turn on the air conditioner.

50

Ventilation

Dehumidifying (With Air

Conditioner)

Warning!

Proceed as follows:

Operate the air conditioner in cool or

cold weather to help defog the

windshield and side windows.

1. Set the Mode Selector Knob to the

position.

Set the temperature control to the hot or

warm position when defogging (Front

Defrost position). Using the Front Defrost

position with the temperature control set to

the cold position is dangerous as it will

cause the outside of the windshield to fog

up. Your vision will be hampered, which

could lead to a serious accident.

2. Set the Air Recirculation Button to

the outside air position.

Proceed as follows:

1. Set the Mode Selector Knob to the

desired position.

3. Set the Temperature Control Knob

to the desired position.

2. Set the Air Recirculation Knob to the

outside air position.

4. Set the Blower Control Knob to the

desired speed.

3. Set the Temperature Control Knob

to the desired position.

Note:

Windshield Defrosting

And Defogging

For maximum defrosting, turn on

the air conditioner, set the Temperature

Control Knob to the extreme hot

position, and turn the Blower Control

Knob fully clockwise.

4. Set the Blower Control Knob to the

desired speed.

Proceed as follows:

1. Set the Mode Selector Knob to the

Front Defrost

5. Turn on the air conditioner by

pressing the A/C Button.

position.

2. Set the Temperature Control Knob to

the desired position.

If warm air is desired from the floor

vents, set the Mode Selector Knob to

Note: One of the functions of the air

conditioner is dehumidifying the air. To

use this function, the temperature does

not have to be set to cold. Set the

Temperature Control Knob to the

desired position (hot or cold), and turn

on the air conditioner to dehumidify the

cabin air.

3. Set the Blower Control Knob to the

desired speed.

the

position.

If equipped with MAX A/C, the

Recirculation Button can be set to the

Recirculated Air position, when the

Blower Control Knob is ON, and the

Mode Selector Knob is set to the Front

Defrost position.

4. If dehumidified heating is desired,

turn on the air conditioner.

51

Automatic Climate Control System

06010900-122-999

Automatic Climate Controls — Type A

1 — Temperature Control Knob

2 — Blower Control Knob

3 — Mode Selector Knob

4 — Rear Window Defrost Button

5 — Air Recirculation Button

6 — A/C Button

52

06010900122

Automatic Climate Controls — Type B

4 — Rear Window Defrost Button

1 — Temperature Control Knob

2 — Blower Control Knob

3 — Mode Selector Knob

5 — Air Recirculation Button

6 — A/C Button

53

Getting To Know Your Vehicle -> Climate Control System for Your Fiat 124 Spider 2 Door Second Generation (2016-2020)

Related Topics

Getting To Know Your Vehicle

Popular Owner Manuals

Latest Owner Manuals