Advertisement

Advertisement

Download User Manual App

Quickly access user manual for free!

Practical information -> Bonnet for Your Fiat Scudo Van Third Generation (2022-2025)

Practical information  
► Open the fixing covers on each bar.  
► Put each fixing point in place and lock them  
to the roof one by one.  
Recommendations  
7
Distribute the load uniformly, taking care  
to avoid overloading one of the sides.  
Arrange the heaviest part of the load as close  
as possible to the roof.  
► Ensure that the roof bars are correctly fitted  
(by shaking them).  
Secure the load firmly.  
► Close the fixing covers on each bar.  
The bars can be interchanged and are adaptable  
to each pair of fixing points.  
Drive gently: the vehicle will be more  
susceptible to the effects of side winds and its  
stability may be affected.  
Regularly check the security and tight  
fastening of the roof bars, at least before each  
trip.  
Roof racks  
Max. authorised load weight:  
– XS: 140 kg,  
Remove the roof bars once they are no longer  
needed.  
– M and XL: 170 kg.  
To t a roof rack, use the fixing points provided  
for this purpose:  
► Place the roof rack on the roof aligned with  
the fixing points and secure each one to the roof  
in turn.  
With panoramic sunroof  
As this value may change, please verify  
the maximum load quoted in the guide  
supplied with the roof bars.  
If the height exceeds 40 cm, adapt the speed  
of the vehicle to the profile of the road to  
avoid damaging the roof bars and the fixings  
on the vehicle.  
► Ensure that the roof rack is correctly fitted (by  
shaking it).  
Be sure to refer to national legislation in order  
to comply with the regulations for transporting  
objects that are longer than the vehicle.  
Bonnet  
Stop & Start  
Before doing anything under the bonnet,  
you must switch off the ignition to avoid any  
risk of the engine restarting automatically.  
Take care with objects or clothing that could  
be caught in the blades of the cooling fan  
Roof bars  
Max. authorised load weight:  
– over 2 roof bars: 100 kg,  
– distributed over 3 roof bars: 150 kg.  
A maximum of 3 roof bars (or 2 bars for the  
version with panoramic sunroof) can be installed  
- use the positions marked in green.  
To install the transverse roof bars, use the fixing  
points provided for this purpose:  
189  
Practical information  
or in certain moving components - risk of  
strangulation and serious injury!  
with care (risk of burns), using the protected  
area.  
When the bonnet is open, take care not to  
damage the safety catch.  
Do not open the bonnet under very windy  
conditions.  
Closing  
► Hold the bonnet and pull out the stay from the  
support slot.  
► Clip the stay in its housing.  
► Lower the bonnet and release it near the end  
of its travel.  
► Pull on the bonnet to check that it is locked  
correctly.  
Electric motor  
Cooling of the engine when stopped  
The engine cooling fan may start after  
the engine has been switched off.  
Take care with objects or clothing that  
could be caught in the blades of the fan!  
Take care with objects or clothing that  
could be caught in the blades of the cooling  
fan or in certain moving components - risk of  
strangulation and serious injury!  
Before carrying out any work under the  
bonnet, you must switch off the ignition, check  
that the READY indicator lamp is off on the  
instrument panel and disconnect the nozzle  
from the charging connector if it is connected.  
Because of the presence of electrical  
equipment under the bonnet, it is strongly  
recommended that exposure to water (rain,  
washing, etc.) be limited.  
Opening  
► Open the door.  
Engine compartment  
The engine shown here is an example for  
illustrative purposes only.  
The locations of the following components may  
vary:  
– Air filter.  
– Engine oil dipstick.  
– Engine oil filler cap.  
– Priming pump.  
The location of the interior bonnet  
release lever prevents the bonnet being  
opened when the left-hand front door is  
closed.  
► Pull the release lever 1, located at the bottom  
of the door frame, towards you.  
► Tilt the safety catch 2 upwards, then raise the  
bonnet.  
When the engine is hot, handle the  
► Unclip the stay 3 from its housing and place it  
in the support slot to hold the bonnet open.  
exterior safety catch and the bonnet stay  
190