Get Features of your vehicle -> INSTRUMENT CLUSTER Guide for Hyundai I10 4 Door Second Generation (2013-2019)

Features of your vehicle

INSTRUMENT CLUSTER

1. Tachometer

2. Engine temperature gauge

3. Fuel gauge

4. Speedometer

5. Turn signal indicators

6. Warning and indicator lights

7. Odometer / Trip computer

❈ The actual cluster in the vehicle may differ

from the illustration.

For more details refer to the "Gauges" in

the next pages.

OBA043100

4 41

Features of your vehicle

■ Type A (km/h)

CAUTION

Do not operate the engine within

the tachometer's RED ZONE. This

may cause severe engine damage.

OBA043103

■ Type B (MPH)

OBA043105

Tachometer

The tachometer indicates the approxi-

mate number of engine revolutions per

minute (rpm).

Use the tachometer to select the correct

shift points and to prevent lugging and/or

over-revving the engine.

OBA043104

Gauges

Speedometer

The speedometer indicates the forward

speed of the vehicle.

The speedometer is calibrated in kilome-

ters per hour and/or miles per hour.

4 42

Features of your vehicle

CAUTION

If the gauge pointer moves beyond

the normal range area toward the

“H” it indicates overheating that

may damage the engine.

WARNING

Never remove the radiator cap

when the engine is hot. The engine

coolant is under pressure and

could cause severe burns. Wait

until the engine is cool before

adding coolant to the reservoir.

OBA043107

OBA043108

Engine coolant temperature gauge

Fuel gauge

(if equipped)

The fuel gauge indicates the approximate

amount of fuel remaining in the fuel tank.

The fuel tank capacity is given in chapter

8. The fuel gauge is supplemented by a

low fuel warning light, which will illuminate

when the fuel tank is nearly empty.

On inclines or curves, the fuel gauge

pointer may fluctuate or the low fuel warn-

ing light may come on earlier than usual

due to the movement of fuel in the tank.

This gauge shows the temperature of the

engine coolant when the ignition switch

is ON.

Do not continue driving with an overheat-

ed engine. If your vehicle overheats, refer

to “If the engine overheats” in chapter 6.

4 43

Features of your vehicle

✽

NOTICE

WARNING - Fuel gauge

It is forbidden to alter the odometer of

all vehicles with the intent to change the

mileage registered on the odometer. The

alteration may void your warranty cov-

erage.

Running out of fuel can expose

vehicle occupants to danger.

You must stop and obtain addition-

al fuel as soon as possible after the

warning light comes on or when the

gauge indicator comes close to the

“E” level.

CAUTION

OBA043110

Avoid driving with a very low fuel

level. Running out of fuel could

cause the engine to misfire, damag-

ing the catalytic converter.

Odometer (km or mi)

The odometer indicates the total dis-

tance the vehicle has been driven.

You will also find the odometer useful to

determine when periodic maintenance

should be performed.

4 44

Features of your vehicle

Press the TRIP button for less than 1

second to select any mode as follows:

Tripmeter A

Tripmeter B

Distance to empty

Average fuel consumption

Instant fuel consumption

Average speed

OBA043099

OBA043111

Tripmeter (km or mi.)

TRIP A : Tripmeter A

TRIP B : Tripmeter B

Tripmeter/Trip computer (if equipped)

The trip computer is a microcomputer-

controlled driver information system that

displays information related to driving,

when the ignition switch is in the ON

position. All stored driving information

(except odometer) resets if the battery is

disconnected.

This mode indicates the distance of indi-

vidual trips selected since the last trip-

meter reset.

Elapsed time

The meter's working range is from 0.0 to

9999.9 km. (0.0 to 9999.9 miles).

Pressing the RESET button for more

than 1 second, when the tripmeter is

being displayed, clears the tripmeter to

zero (0.0).

ECO ON/OFF*

* if equipped

4 45

Features of your vehicle

OBA043112

OBA043113

OBA043231

Distance to empty

(km or mi.)

Average fuel consumption

Instant fuel consumption

(l/100 km or MPG)

This mode indicates the estimated dis-

tance to empty based on the current fuel in

the fuel tank and the amount of fuel deliv-

ered to the engine. When the remaining

distance is below 50 km (30 miles), “---” will

be displayed.

This mode calculates the average fuel

consumption from the total fuel used and

the distance since the last average con-

sumption reset. The total fuel used is cal-

culated from the fuel consumption input.

For an accurate calculation, drive more

than 300 m (0.18 miles).

Pressing the RESET button for more than

1 second, when the average fuel con-

sumption is being displayed, clears the

average fuel consumption to zero (--.-).

This mode calculates the instant fuel

consumption of the last few seconds.

The meter’s working range is from 50 to

999 km (30 to 615 miles).

4 46

Features of your vehicle

✽

NOTICE

• If the vehicle is not on level ground or

the battery power has been interrupt-

ed, the “Distance to empty” function

may not operate correctly.

The trip computer may not register

additional fuel if less than 6 liters (1.6

gallons) of fuel are added to the vehicle.

• The fuel consumption and distance to

empty may vary significantly based

on driving conditions, driving habits,

and condition of the vehicle.

OBA043114

OBA043115

• The distance to empty is an estimate

of the available driving distance. This

may differ from the actual driving dis-

tance available.

Average speed (km/h or MPH)

Elapsed time

This mode calculates the average speed

of the vehicle since the last average

speed reset.

Even if the vehicle is not in motion, the

average speed keeps going while the

engine is running.

For an accurate calculation, drive more

than 300 m (0.18 miles).

Pressing the RESET button for more

than 1 second, when the average speed

is being displayed, clears the average

speed to zero (---).

This mode indicates the total time trav-

eled since the last driving time reset.

Even if the vehicle is not in motion, the

driving time keeps going while the engine

is running.

The meter’s working range is from

00:00~99:59.

Pressing the RESET button for more

than 1 second, when the driving time is

being displayed, clears the driving time to

zero (00:00).

4 47

Features of your vehicle

“FUSE ON” warning light

(if equipped)

Warnings and indicators

All warning lights are checked by turning

the ignition switch ON (do not start the

engine). If any light that does not illumi-

nate, we recommend that the system be

checked by an authorized HYUNDAI

dealer. After starting the engine, check to

make sure that all warning lights are off.

If any warning lights are still on, this indi-

cates a situation that needs attention.

This warning light illuminates if the fuse

switch in the fuse box is OFF.

Turn the fuse switch on, when the “FUSE

ON” warning light illuminates.

For more details, refer to “Fuses” in chap-

ter 7.

OBA043116

ECO ON/OFF mode (if equipped)

You can turn the ECO indicator on/off on

the instrument cluster in this mode.

If you press the RESET button for more

than 1 second in the ECO ON mode,

ECO OFF is displayed in the screen and

the ECO indicator turns off while driving.

If you want to display the ECO indicator

again, press the RESET button for more

than 1 second in the ECO OFF mode

and then ECO ON mode is displayed in

the screen.

4 48

Features of your vehicle

Electronic brake force distri-

bution (EBD) system warning

light

Air bag warning light

(if equipped)

Anti-lock brake system

(ABS) warning light

(if equipped)

If these two warning lights

illuminate at the same time

while driving, your vehicle’s

ABS and EBD system may have mal-

functioned.

In this case, your ABS and regular brake

system may not work normally. We rec-

ommend that the system be checked by

an authorized HYUNDAI dealer.

This warning light illuminates if the igni-

tion switch is turned to the ON position

and goes off after approximately 3 sec-

onds if the system is operating normally.

If the ABS warning light remains on,

comes on while driving, or does not

come on when the ignition switch is

turned to the ON position, this indicates

that the ABS may have malfunctioned.

If this occurs, we recommend that the

system be checked by an authorized

HYUNDAI dealer. The normal braking

system will still be operational, but with-

out the assistance of the anti-lock brake

system.

This warning light will illuminate for

approximately 6 seconds each time you

turn the ignition switch to the ON position.

This light also comes on when the

Supplemental Restraint System (SRS) is

not working properly. If the air bag warn-

ing light does not come on, or continu-

ously remains on after operating for

about 6 seconds when you turned the

ignition switch to the ON position or start-

ed the engine, or if it comes on while

driving, we recommend that the system

be inspected by an authorized HYUNDAI

dealer.

WARNING

If both ABS and Brake warning

lights are on and stay on, your vehi-

cle’s brake system will not work

normally during sudden braking. In

this case, avoid high speed driving

and abrupt braking.We recommend

that the system be checked by an

authorized HYUNDAI dealer.

4 49

Features of your vehicle

Seat belt warning

Turn signal indicator

Parking (Position)

light indicator

This indicator illuminates when the park-

ing (position) lights are on.

As a reminder to the driver, the seat belt

warning light will blink for approximately

6 seconds each time you place the igni-

tion switch in the ON position regardless

of belt fastening. If the driver’s seat belt is

unfastened after the ignition switch is

placed in the ON position, the seat belt

warning light blinks again for approxi-

mately 6 seconds. If the driver's seat belt

is not fastened when the ignition switch is

placed in the ON position or if it is unfas-

tened after the ignition switch is placed in

the ON position, the seat belt warning

chime will sound for approximately 6 sec-

onds. At this time, if the seat belt is fas-

tened, the chime will stop at once. (if

equipped)

The left or right turn signal indicator

blinks when you signal a lane change or

turn. If the arrow comes on but does not

blink, blinks more rapidly than normal, or

does not illuminate at all, a malfunction in

the turn signal system is indicated. We

recommend that you consult an author-

ized HYUNDAI dealer repairs.

High beam indicator

This indicator illuminates when the head-

lights are on and in the high beam posi-

tion or when the turn signal lever is pulled

into the Flash-to-Pass position.

4 50

Features of your vehicle

Engine oil pressure warn-

ing light

Parking brake & brake

CAUTION

fluid warning

If the oil pressure warning light

stays on while the engine is run-

ning, serious engine damage may

result. The oil pressure warning

light comes on whenever there is

insufficient oil pressure. In normal

operation, it should come on when

the ignition switch is turned on, then

goes off when the engine starts. If

the oil pressure warning light stays

on while the engine is running, there

is a serious malfunction.

This light illuminates if the ignition switch is

turned ON and goes off in approximately 3

seconds if the parking brake is not applied.

This warning light indicates the engine oil

pressure is low.

If the warning light illuminates while driv-

ing:

1.Drive safely to the side of the road and

stop.

2.With the engine off, check the engine

oil level. If the level is low, add oil as

required.

If the warning light remains on after

adding oil or if oil is not available, we rec-

ommend that you call an authorized

HYUNDAI dealer.

Parking brake warning

This warning light is illuminated when the

parking brake is applied with the ignition

switch in the START or ON position. The

warning light should go off when the

parking brake is released.

If this happens, stop the vehicle as

soon as it is safe to do so, turn off

the engine and check the oil level. If

the oil level is low, fill the engine oil

to the proper level and start the

engine again. If the light stays on

with the engine running, turn the

engine off immediately. In any

instance where the oil light stays on

when the engine is running, we rec-

ommend that the system be

checked by an authorized HYUNDAI

dealer.

Low brake fluid level warning

If the warning light remains on, it may

indicate that the brake fluid level in the

reservoir is low.

CAUTION

If the warning light remains on:

1.Drive carefully to the nearest safe loca-

tion and stop your vehicle.

2.With the engine stopped, check the

brake fluid level immediately and add

fluid as required. Then check all brake

components for fluid leaks.

If the engine is not stopped imme-

diately after the engine oil pressure

warning light is illuminated, severe

damage could result.

3.Do not drive the vehicle if leaks are

found, the warning light remains on or

the brakes do not operate properly. We

recommend that you contact an

authorized HYUNDAI dealer.

4 51

Features of your vehicle

Your vehicle is equipped with dual-diago-

nal braking systems. This means you still

have braking on two wheels even if one of

the dual systems should fail.With only one

of the dual systems working, more than

normal pedal travel and greater pedal

pressure are required to stop the vehicle.

Also, the vehicle will not stop in as short a

distance with only a portion of the brake

system working. If the brakes fail while you

are driving, shift to a lower gear for addi-

tional engine braking and stop the vehicle

as soon as it is safe to do so.

Front fog light indicator

(if equipped)

Shift pattern indicator

(if equipped)

This indicator illuminates when the front

fog lights are ON.

The indicator displays which automatic

transaxle shift lever is selected.

Rear fog light indicator

(If equipped)

This indicator illuminates when the rear

fog lights are ON.

To check bulb operation, check whether

the parking brake and brake fluid warning

light illuminates when the ignition switch

is in the ON position.

WARNING

Driving the vehicle with a warning

light on is dangerous. If the brake

warning light remains on, we recom-

mend that the system be checked by

an authorized HYUNDAI dealer.

4 52

Features of your vehicle

Manual transaxle shift

indicator (if equipped)

Charging system warning

light

Tailgate/trunk open warn-

ing light

This indicator informs you which gear is

desired while driving to save fuel.

For example

This warning light illuminates when the

tailgate is not closed securely.

This warning light indicates a malfunction

of either the generator or electrical

charging system.

If the warning light illuminates while the

vehicle is in motion:

: Indicates that shifting up to the

3rd gear is desired (currently

the shift lever is in the 2nd

gear).

: Indicates that shifting down to

the 3rd gear is desired (cur-

rently the shift lever is in the 4th

gear).

Door ajar warning light

1.Drive to the nearest safe location.

2.With the engine off, check the genera-

tor drive belt for looseness or break-

age.

3.If the belt is adjusted properly, a prob-

lem exists somewhere in the electrical

charging system. We recommend that

the system be checked by an author-

ized HYUNDAI dealer.

This warning light illuminates when a

door is not closed securely.

✽

NOTICE

When the system is not working proper-

ly, up & down arrow indicator and gear

are not displayed.

4 53

Features of your vehicle

Immobilizer indicator

(if equipped)

• If the indicator illuminates only for 2

seconds and goes out when the

engine start/stop button is turned to

ON position with the smart key in the

vehicle, have the system checked by

an authorized HYUNDAI dealer.

• When the battery is weak, if the engine

start/stop button is pressed, the indica-

tor will blink and you are not able to

start the engine. However, you are able

to start the engine by inserting the

smart key in the smart key holder. Also,

if the smart key system related parts

have a problem, the indicator will blink.

Malfunction indicator light

(MIL) (check engine light)

Without smart key system

This indicator is part of the Engine

Control System which monitors various

emission control system components. If

this indicator illuminates while driving, it

indicates that a potential malfunction has

been detected somewhere in the emis-

sion control system.

This indicator will also illuminates when

the ignition switch is turned to the ON

position, and will go off in a few seconds

after the engine is started. If it illuminates

while driving, or does not illuminate when

the ignition switch is turned to the ON

position, we recommend that the system

be checked by an authorized HYUNDAI

dealer.

This indicator illuminates when the

immobilizer key is inserted and turned to

the ON position to start the engine. At

this time, you can start the engine. The

light goes off after the engine runs. If this

light blinks when the ignition switch is in

the ON position before starting the

engine, we recommend that the system

be checked by an authorized HYUNDAI

dealer.

Low fuel level warning

light

With smart key system

If any of the following occurs in a vehicle

equipped with the smart key, the immobi-

lizer indicator illuminates blinks or goes

off.

Generally, your vehicle will continue to be

drivable, we recommend that the system

be checked by an authorized HYUNDAI

dealer.

This warning light indicates the fuel tank

is nearly empty. When it comes on, you

should add fuel as soon as possible.

Driving with the fuel level warning light on

or with the fuel level below “E” can cause

the engine to misfire and damage the

catalytic converter (if equipped).

• When the smart key is in the vehicle, if

the engine start/stop button is in the

ACC or ON position, the indicator will

illuminate for approximately 30 sec-

onds to indicate that you are able to

start the engine. However, when the

smart key is not in the vehicle, if the

engine start/stop button is pressed, the

indicator will blink for a few seconds to

indicate that you are not be able to

start the engine.

4 54

Features of your vehicle

ESC (Electronic Stability

Control) indicator

(if equipped)

ESC OFF indicator

(if equipped)

CAUTION

• Prolonged driving with the

Emission

Control

System

Malfunction Indicator Light illumi-

nated may cause damage to the

emission control systems which

could affect drivability and/or fuel

economy.

• If the Emission Control System

Malfunction Indicator Light illumi-

nates, potential catalytic convert-

er damage is possible which

could result in loss of engine

power. We recommend that the

system be inspected by an

authorized HYUNDAI dealer.

The ESC indicator will illuminate when

the ignition switch is turned ON, but

should go off after approximately 3 sec-

onds. When the ESC is on, it monitors

the driving conditions. Under normal driv-

ing conditions, the ESC indicator will

remain off. When a slippery or low trac-

tion condition is encountered, the ESC

will operate, and the ESC indicator will

blink to indicate the ESC is operating.

But, if the ESC system malfunctions the

indicator illuminates and stays on. We

recommend that the system be checked

by an authorized HYUNDAI dealer.

The ESC OFF indicator will illuminate

when the ignition switch is turned ON,

but should go off after approximately 3

seconds. To switch to ESC OFF mode,

press the ESC OFF button. The ESC

OFF indicator will illuminate indicating

the ESC is deactivated.

4 55

Features of your vehicle

Key reminder warning chime

(if equipped)

Electric power steering

(EPS) system warning light

(if equipped)

KEY OUT indicator

(if equipped)

KEY

OUT

If the driver’s door is opened while the

ignition key is left in the ignition switch

(ACC or LOCK position), the key

reminder warning chime will sound. This

is to prevent you from locking your keys

in the vehicle.The chime sounds until the

key is removed from the ignition switch or

the driver’s door is closed.

When the engine start/stop button is in

the ACC or ON position, if any door is

open, the system checks for the smart

key. If the smart key is not in the vehicle,

the indicator will blink, and if all doors are

closed, the chime will also sound for

about 5 seconds. The indicator will go off

while the vehicle is moving. Keep the

smart key in the vehicle.

This indicator light illuminates after the

ignition key is turned to the ON position

and then it will go off when the engine

starts.

This light also comes on when the EPS

has malfunctioned. If it comes on while

driving, we recommend that the system

be inspected by an authorized HYUNDAI

dealer.

4 56

Features of your vehicle

Overspeed warning

(if equipped)

120

km/h

Overspeed warning light

If you drive with the speed of 120 km/h or

more, the overspeed warning light will

blink. This is to prevent you from over-

speeding.

Overspeed warning chime (if equipped)

If you drive with the speed of 120km/h or

more, the overspeed warning chime will

sound for about 5 seconds.This is to pre-

vent you from overspeeding.

4 57

Features of your vehicle -> INSTRUMENT CLUSTER for Your Hyundai I10 4 Door Second Generation (2013-2019)

Related Topics

Features of your vehicle

Popular Owner Manuals

Latest Owner Manuals