Get Safety system -> Child restraint system (CRS) Guide for Hyundai I10 4 Door Third Generation (2020-2026)

03

CHILD RESTRAINT SYSTEM ǣCRSǤ

Child Restraint Systems must be

Our recommendation:

Children always in the rear

properly placed and installed in the

rear seat. You must use a commer-

cially available Child Restraint

System that meets the requirements

of the Safety Standards of your coun-

try.

WARNING

Always properly restrain children

in the rear seats of the vehicle,

unless the air bag on the front pas-

senger seat is deactivated.

Child Restraint Systems are general-

ly designed to be secured in a vehicle

seat by lap belt or the lap belt portion

of a lap/shoulder belt, or by a top-

tether and/or ISOFIX anchorage in

the rear seats of the vehicle.

Children of all ages are safer when

restrained in the rear seat. A child

riding in the front passenger seat

can be forcefully struck by an

inflating air bag resulting in

SERIOUS INJURY or DEATH.

Child Restraint System (CRS)

always in the rear

Infants and younger children must be

restrained in an appropriate rear-

ward-facing or forward-facing CRS

that has first been properly secured

to the rear seat of the vehicle. Read

and comply with the instructions for

installation and use provided by the

manufacturer of the Child Restraint

System.

Children under age 13 must always

ride in the rear seats and must always

be properly restrained to minimise

the risk of injury in an accident, sud-

den stop or sudden manoeuvre.

According to accident statistics, chil-

dren are safer when properly

restrained in the rear seats than in

the front seat. Children too large for a

Child Restraint System must use the

seat belts provided.

WARNING

Most countries have Child Restraint

Systems which require children to

travel in approved Child Restraint

Systems. The laws governing the age

or height/weight restrictions at which

seat belts can be used instead of

Child Restraint System differs among

countries, so you should be aware of

the specific requirements in your

country, and where you are travelling.

ꢀ Always follow the Child Restraint

System manufacturer’s instruc-

tions for installation and use.

ꢀ Always properly restrain your

child in the Child Restraint

System.

ꢀ Do not use an infant carrier or a

child safety seat that “hooks”

over a seatback, it may not pro-

vide adequate protection in an

accident.

ꢀ After an accident, we recom-

mend a HYUNDAI dealer check

the Child Restraint System, seat

belts, ISOFIX anchorages and

top-tether anchorages.

3-29

Safety system

Selecting a Child Restraint

System (CRS)

When selecting a CRS for your child,

always:

ꢀ Make sure the CRS has a label cer-

tifying that it meets applicable

Safety Standards of your country.

ꢀ Select a Child Restraint System

based on your child’s height and

weight. The required label or the

instructions for use typically provide

this information.

CRS09

Rearward-facing Child Restraint

System

ꢀ Select a Child Restraint System

that fits the vehicle seating position

where it will be used.

A rearward-facing Child Restraint

System provides restraint with the

seating surface against the back of

the child. The harness system holds

the child in place, and in an accident,

acts to keep the child positioned in

the Child Restraint Systems and

reduce the stress to the fragile neck

and spinal cord.

ꢀ Read and comply with the warnings

and instructions for installation and

use provided with the Child

Restraint System.

Child Restraint System types

All children under the age of one year

must always ride in a rearward-facing

Child Restraint System. There are

different types of rearward-facing

Child Restraint Systems: infant-only

Child Restraint Systems can only be

used rearward-facing. Convertible

and 3-in-1 Child Restraint Systems

typically have higher height and

weight limits for the rearward-facing

position, allowing you to keep your

child rearward-facing for a longer

period of time.

There are three main types of Child

Restraint Systems: rearward-facing

seats, forward-facing seats, and

booster seats. They are classified

according to the child’s age, height

and weight.

Keep using Child Restraint Systems

in the rearward-facing position as

long as children fit within the height

and weight limits allowed by the Child

Restraint System’s manufacturer.

3-30

03

Installing a Child Restraint

System (CRS)

WARNING

Before installing your Child

Restraint System always:

Read and follow the instructions

provided by the manufacturer of

the Child Restraint System.

OIB034017

Failure to follow all warnings and

instructions could increase the

risk of the SERIOUS INJURY or

DEATH if an accident occurs.

Forward-facing Child Restraint

System

A

forward-facing Child Restraint

System provides restraint for the

child’s body with a harness. Keep

children in a forward-facing Child

Restraint System with a harness until

they reach the top height or weight

limit allowed by your Child Restraint

System’s manufacturer.

WARNING

If the vehicle head restraint pre-

vents proper installation of a Child

Restraint System, the head

restraint of the respective seating

position shall be readjusted or

entirely removed.

Once your child outgrows the for-

ward-facing Child Restraint System,

your child is ready for a booster seat.

After selecting

a

proper Child

Booster seats

Restraint System and checking that

the Child Restraint System fits prop-

erly in the rear of this vehicle, you are

ready to install the Child Restraint

System according to the manufactur-

er’s instruction. There are three gen-

eral steps in installing the Child

Restraint Systems properly:

A booster seat is Child Restraint

System designed to improve the fit of

the vehicle’s seat belt system. A

booster seat positions the seat belt

so that it fits properly over the stron-

ger parts of your child’s body. Keep

your children in booster seats until

they are big enough to fit in a seat

belt properly.

ꢀ Properly secure the Child

Restraint System to the vehicle.

All Child Restraint System must be

secured to the vehicle with the lap

belt or lap part of a lap/shoulder belt

or with the ISOFIX top-tether and/or

ISOFIX anchorage.

For a seat belt to fit properly, the lap

belt must lie comfortable across the

upper thighs, not the stomach. The

shoulder belt should lie comfortable

across the shoulder and chest and

not across the neck or face. Children

under age 13 must always be prop-

erly restrained to minimise the risk of

injury in an accident, sudden stop or

sudden manoeuvre.

3-31

Safety system

ꢀ Make sure the Child Restraint

System is firmly secured. After

installing a Child Restraint System

to the vehicle, push and pull the

seat forward and from side-to-side

to verify that it is securely attached

to the seat. A Child Restraint

System secured with a seat belt

should be installed as firmly as pos-

sible. However, some side-to- side

movement can be expected.

ISOFIX anchorage and top-tether

anchorage (ISOFIX anchorages

system) for children

The ISOFIX system holds a Child

Restraint System during driving and

in an accident. This system is

designed to make installation of the

Child Restraint System easier and

reduce the possibility of improperly

installing your Child Restraint System.

The ISOFIX system uses anchors in

the vehicle and attachments on the

Child Restraint System. The ISOFIX

system eliminates the need to use

seat belts to secure the Child

Restraint System to the rear seats.

When installing a Child Restraint

System, adjust the vehicle seat (up

and down, forward and rearward)

so that your child fits in the Child

Restraint System in a comfortable

manner.

ISOFIX anchorages are metal bars

built into the vehicle. There are two

lower anchors for each ISOFIX seat-

ing position that will accommodate a

Child Restraint System with lower

attachments.

ꢀ Secure the child in the Child

Restraint System. Make sure the

child is properly strapped in the

Child Restraint System according

to the Child Restraint System man-

ufacturer’s instructions.

To use the ISOFIX system in your

vehicle, you must have a Child

Restraint System with ISOFIX attach-

ments. (An ISOFIX Child Restraint

System may only be installed if it has

vehicle-specific or universal approval

in accordance with the requirements

of ECE-R44 or ECE-R129.)

CAUTION

A Child Restraint System in a

closed vehicle can become very

hot. To prevent burns, check the

seating surface and buckles before

placing your child in the Child

Restraint System.

The Child Restraint System manufac-

turer will provide you with instructions

on how to use the Child Restraint

System with its attachments for the

ISOFIX anchorages.

3-32

03

OAC3039009TU

OOSEV038012

ISOFIX anchorages have been pro-

vided in the left and right outboard

rear seating positions. Their locations

are shown in the illustration. There

are no ISOFIX anchorages provided

for the centre rear seating position.

WARNING

Do not attempt to install a Child

Restraint System using ISOFIX

anchorages in the rear centre seat-

ing position. There are no ISOFIX

anchorages provided for this seat.

Using the outboard seat anchor-

ages, for the CRS installation on

the rear centre seating position,

can damage the anchorages.

OAC3039010TU

[A] : ISOFIX Anchorage Position Indicator,

[B] : ISOFIX Anchorage

The ISOFIX anchorages symbols are

located on the left and right rear seat

cushions to identify the position of the

ISOFIX anchorages in your vehicle

(see arrows in illustration). Both rear

outboard seats are equipped with a

pair of ISOFIX anchorages as well as

a corresponding top-tether anchor-

age on the back side of the rear seats.

(Child Restraint Systems with univer-

sal approval according to ECE-R44

or ECE-R129 need to be fixed addi-

tionally with a top-tether connected to

the back side of the rear seats.)

ISOFIX anchorages are located

between the seatback and the seat

cushion of the rear seat left and right

outboard seating positions.

To use the ISOFIX anchorages, push

the upper portion of the ISOFIX

anchorage cover.

3-33

Safety system

Securing a Child Restraint

System with the “ISOFIX

Anchorage System”

To install a ISOFIX-compatible Child

Restraint System in either of the rear

outboard seating positions:

WARNING

Take the following precautions

when using the ISOFIX system:

ꢀ Read and follow all installation

instructions provided with your

Child Restraint System.

1. Move the seat belt buckle away

from the ISOFIX anchorages.

ꢀ To prevent the child from reach-

ing and taking hold of unretract-

ed seat belts, buckle all unused

rear seat belts and retract the

seat belt webbing behind the

child. Children can be strangled

2. Move any other objects away from

the anchors that could prevent a

secure connection between the

Child Restraint System and the

ISOFIX anchorages.

if

a

shoulder belt becomes

3. Place the Child Restraint System

on the vehicle seat, then attach the

seat to the ISOFIX anchorages

according to the instructions pro-

vided by the Child Restraint

System manufacturer.

wrapped around their neck and

the seat belt tightens.

ꢀ NEVER attach more than one

Child Restraint System to a sin-

gle anchorage. This could cause

the anchor or attachment to

come loose or break.

4. Follow the instructions of the Child

Restraint System’s manufacturer

for proper installation and connec-

tion of the ISOFIX attachments on

the Child Restraint System to the

ISOFIX anchorages.

ꢀ Always have the ISOFIX system

inspected by your dealer after an

accident. An accident can dam-

age the ISOFIX system and may

not properly secure the Child

Restraint System.

3-34

03

Securing a Child Restraint

System seat with “Top-tether

Anchorage” system

WARNING

Take the following precautions

when installing the top-tether:

ꢀ Read and follow all installation

instructions provided with your

Child Restraint System.

ꢀ NEVER attach more than one

Child Restraint System to a sin-

gle ISOFIX top-tether anchorage.

This could cause the anchorage

or attachment to come loose or

break.

OAC3039011TU

ꢀ Do not attach the top-tether to

anything other than the correct

top-tether anchorage. It may not

work properly if attached to

something else.

Top-tether anchorages for Child

Restraint Systems are located on the

rear of the seatback.

ꢀ Child Restraint anchorages are

designed to withstand only those

loads imposed by correctly fitted

Child Restraint System.

Under no circumstances are they

to be used for adult seat belts or

harnesses or for attaching other

items or equipment to the vehi-

cle.

OAC3039012TU

1. Route the Child Restraint System

seat strap over the seatback.

For vehicles with adjustable head

restraint, route the tether strap

under the head restraint and

between the head restraint posts,

otherwise route the tether strap

over the top of the seatback.

2. Connect the top-tether to the top-

tether anchorage, then tighten the

top-tether according to the instruc-

tions of your Child Restraint

System’s manufacturer to firmly

attach the Child Restraint System

to the seat.

3-35

Safety system

3-36

03

Note ¹⁾: The universal belted CRS applies to all mass groups.

Note ²⁾: Seating position not suitable for child restraint system if the passenger’s front

air bag is activate.

Note ³⁾: To install a ISOFIX Child Restraint Systems :

- Driver Seat : You should move the seat at mid position and adjust the height

of seat to highest and head restraint stay angle to 9° position.

- Front Passenger Seat : You should move the seat at foremost and head

restraint stay angle to 9° position.

Note ⁴⁾: To install a ISOFIX Child Restraint Systems:

You should remove the head restraint of the seat.

Note ⁵⁾: The seating position (number 5) is not suitable for fitment of child restraint sys-

tem with support leg.

K Do not use forward facing child restraint system when child’s weight is below 13 kg at

all seat.

K For semi-universal or vehicle specific CRS(ISOFIX or belted CRS), please see the

vehicle list provided in the manual of CRS.

Seat

Number

Position

in the vehicle

1

Front right

Front centre

Front left

2

3

4

2^ndrow right

2^ndrow centre

2^ndrow left

5*

6

OOSEV038035R

* : 5 Seater, if equipped

Recommended Child Restraint Systems (for Europe)

Mass

group

ECE-R44/R129

Approval No.

Name

Manufacturer

Type of Fixation

Cabriofix &

Familyfix

Group 0+

Maxi Cosi

ISOFIX

E4 04443907

E1 04301133

E1 04301323

Group I

Duo Plus

Britax Römer

ISOFIX and top-tether

Forward-facing with ISOFIX

and vehicle belt

Group II KidFix II XP Britax Römer

Group III Junior III Graco

CRS Manufacturer information

Forward-facing with vehicle E11 03.44.164

belt E11 03.44.165

Maxi Cosi Cabriofix & Familyfix http://www.maxi-cosi.com

Britax Römmer http://www.britax.com

Graco http//www.gracobaby.com

3-37

Safety system

Securing a Child Restraint

System with a lap/shoulder belt

WARNING

ꢀ Never place a Child Restraint

System on the front passenger

seat, unless the passenger air

bag is deactivated.

When not using the ISOFIX system,

all Child Restraint Systems must be

secured to a rear seat with the lap

part of a lap/shoulder belt.

ꢀ For semi-universal or vehicle

specific CRS (ISOFIX or belted

CRS), please see the vehicle list

provided in the manual of CRS.

ꢀ It is recommended to remove the

head restraint, when CRS is

unstable due to head restraint.

OHI038145

Installing a Child Restraint System

with a lap/shoulder belt

To install a Child Restraint System on

the rear seats, do the following:

1. Place the Child Restraint System

on a rear seat and route the lap/

shoulder belt around or through

the restraint, following the restraint

manufacturer’s instructions. Make

sure the seat belt webbing is not

twisted.

Information

i

When using the rear centre seat belt,

you should also refer to the “Rear

Centre Seat Belt” in this chapter.

3-38

03

OHI038146

OHI038183L

2. Fasten the lap/shoulder belt latch

into the buckle. Listen for the dis-

tinct “click” sound.

3. Remove as much slack from the

belt as possible by pushing down

on the Child Restraint System

whilst feeding the shoulder belt

back into the retractor.

Information

i

4. Push and pull on the Child Restraint

System to confirm that the seat

belt is holding it firmly in place.

Position the release button so that it is

easy to access in case of an emergency.

If your CRS manufacturer instructs or

recommends you use a top-tether

anchorage with the lap/shoulder belt,

see page 3-36.

To remove the Child Restraint

System, press the release button on

the buckle and then pull the lap/

shoulder belt out of the restraint and

allow the seat belt to retract fully.

3-39

Safety system -> Child restraint system (CRS) for Your Hyundai I10 4 Door Third Generation (2020-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals