2019-2026 Lexus UX SUV Operating the lights and wipers User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Operating the lights and wipers for Your Lexus UX SUV First Generation (2019-2026)

198
4-3. Operating the lights and wipers
4-3.Operating the lights and wipers
Operating the switch turns on
the lights as follows:
U.S.A.
Canada
1 The side marker, parking, tail,
license plate, instrument panel
lights, and daytime running lights
(P.198) turn on.
2 The headlights and all the
lights listed above (except daytime
running lights) turn on.
3 The headlights, daytime run-
ning lights (P.198) and all the
lights listed above turn on and off
automatically.
4 (U.S.A.) Off
■ AUTO mode can be used when
The power switch is in ON.
■ Daytime running light system
● The daytime running lights illuminate the
parking lights and illuminate brighter than
the parking lights.
● To make your vehicle more visible to
other drivers during daytime driving, the
daytime running lights turn on automati-
cally when all of the following conditions
are met. (The daytime running lights are
not designed for use at night.)
• The hybrid system is started
• The parking brake is released
• The headlight switch is in the or
(when the surroundings are bright) posi-
tion
The daytime running lights remain on after
they illuminate due to the conditions above,
even if the parking brake is set again.
● For the U.S.A.: Daytime running lights
can be turned off by operating the head-
light switch to position.
● Compared to turning on the headlights,
the daytime running light system offers
greater durability and consumes less
electricity, so it can help improve fuel
economy.
■ Headlight control sensor
The sensor may not function properly if an
object is placed on the sensor, or anything
that blocks the sensor is affixed to the wind-
shield.
Doing so interferes with the sensor detect-
ing the level of ambient light and may cause
the automatic headlight system to malfunc-
tion.
Headlight switch
The headlights can be operated
manually or automatically.
Turning on the headlights
A
B
199
4-3. Operating the lights and wipers
4
Driving
■ Automatic light off system
● When the headlights come on: The head-
lights and tail lights turn off 30 seconds
after the driver’s door is opened and
closed if the power switch is turned to
OFF. (The lights turn off immediately if
on the key is pressed after all the
doors are locked.)
● When only the tail lights come on: The tail
lights turn off automatically if the power
switch is turned to OFF. and the driver’s
door is opened.
Except for Canada: To turn the lights on
again, turn the power switch to ON, or turn
the light switch off once and then back to
or .
For Canada: To turn the lights on again, turn
the power switch to ON, or turn the light
switch to once and then back to
or .
■ Automatic headlight leveling system (if
equipped)
The level of the headlights is automatically
adjusted according to the number of pas-
sengers and the loading condition of the
vehicle to ensure that the headlights do not
interfere with other road users.
■ Windshield wiper linked headlight illu-
mination
When driving during daytime with the
headlight switch turned to position, if
the windshield wipers are used, the head-
lights will turn on automatically after several
seconds to help enhance the visibility of
your vehicle.
■ 12-volt battery-saving function
In order to prevent the 12-volt battery of the
vehicle from discharging, if the headlights
and/or tail lights are on when the power
switch is turned off the 12-volt battery sav-
ing function will operate and automatically
turn off all the lights after approximately 20
minutes. When the power switch is turned
to ON, the 12-volt battery-saving function
will be disabled.
When any of the following are performed,
the 12-volt battery-saving function is can-
celed once and then reactivated. All the
lights will turn off automatically 20 minutes
after the 12-volt battery-saving function has
been reactivated:
● When the headlight switch is operated
● When a door is opened or closed
■ Welcome light illumination control
The parking and tail lights automatically
turn on at night when the doors are
unlocked using the entry function or wire-
less remote control if the light switch is in
the position.
■ If “Headlight System Malfunction Visit
Your Dealer” is displayed on the multi-
information display
The system may be malfunctioning. Have
the vehicle inspected by your Lexus dealer.
■ Customization
Settings (e.g. light sensor sensitivity) can be
changed. (Customizable features:
P.460)
NOTICE
■ To prevent 12-volt battery discharge
Do not leave the lights on longer than
necessary when the hybrid system is not
operating.
200
4-3. Operating the lights and wipers
1 With the headlights on, push the
lever away from you to turn on the
high beams.
Pull the lever toward you to the center
position to turn the high beams off.
2 Pull the lever toward you and
release it to flash the high beams
once.
You can flash the high beams with the
headlights on or off.
When any of the following conditions is
met, while the headlights (low beam)
are on, the cornering lights will addi-
tionally turn on and light up the direc-
tion of movement for the vehicle. This is
to ensure excellent visibility when
either driving at intersections or park-
ing at night.
The steering wheel is operated
The turn signal lever is operated
The shift position is in R (both left
and right side cornering lights)
■ Cornering light control
● The lights illuminate when the vehicle
speed is approximately 19 mph (30
km/h) or less. However, the lights turn off
when the vehicle speed increases to
approximately 22 mph (35 km/h) or
more.
● After the lights remain illuminated for 30
minutes, they automatically turn off.
Turning on the high beam head-
lights
Cornering lights (if equipped)
201
4-3. Operating the lights and wipers
4
Driving
1 Press the Automatic High Beam
switch.
2
Turn the headlight switch to the
or position.
When the headlight switch lever is in the
low beam position, the AHB system will be
enabled and the AHB indicator will illumi-
nate.
■ Automatic operating conditions of the
high beams
● When all of the following conditions are
met, the high beams will illuminate auto-
matically:
• The vehicle speed is approximately 21
mph (34 km/h) or more.
• The area ahead of the vehicle is dark.
• There are no vehicles ahead with lights
on.
• There are few streetlights or other lights
on the road ahead.
● If any of the following conditions are met,
the headlights will change to the low
beams:
• Vehicle speed drops below approxi-
mately 17 mph (27 km/h).
• The area ahead of the vehicle is not dark.
• There is a vehicle ahead with lights on.
• There are many streetlights or other
lights on the road ahead.
■ Front camera detection
● In the following situations, the high beams
may not be automatically changed to the
low beams:
• When a vehicle cuts in front of your vehi-
cle
• When another vehicle crosses in front of
the vehicle
• When vehicles ahead are repeatedly
detected and then hidden due to
repeated curves, road dividers or road-
side trees
• When a vehicle ahead approaches from
a far lane
• When a vehicle ahead is far away
AHB (Automatic High
B
eam)
The Automatic High Beam uses a
front camera located on the upper
portion of the windshield to detect
the brightness of the lights of vehi-
cles ahead, streetlights, etc., and
automatically changes the head
lights between the high beams and
low beams.
WARNING
■ For safe use
Do not overly rely on the Automatic
High Beam. Always drive safely, taking
care to observe your surroundings and
turning the high beams on or off manu-
ally if necessary.
■ To prevent unintentional operation of
the Automatic High Beam system
When it is necessary to disable the sys-
tem P.215
Using the Automatic High Beam
system
202
4-3. Operating the lights and wipers
• When a vehicle ahead has no lights
• When the lights of a vehicle ahead are
dim
• When a vehicle ahead is reflecting strong
light, such as own headlights
• Situations in which the sensors may not
operate properly P.218
● The headlights may change to the low
beams if a vehicle ahead that is using fog
lights without its headlights turned on is
detected.
● House lights, street lights, traffic signals,
and illuminated billboards or signs may
cause the high beams to change to the
low beams, or the low beams to remain
on.
● The following may change the timing at
which the headlights change to the low
beams:
• The brightness of lights of vehicles ahead
• The movement and direction of vehicles
ahead
• The distance between the vehicle and a
vehicle ahead
• When a vehicle ahead only has lights illu-
minated on one side
• When a vehicle ahead is a two-wheeled
vehicle
• The condition of the road (gradient,
curve, condition of the road surface, etc.)
• The number of passengers and amount of
luggage
● The headlights may change between the
high beams and low beams unexpect-
edly.
● Bicycles and other small vehicles may not
be detected.
● In the following situations, the system may
not be able to correctly detect the bright-
ness of the surroundings. This may cause
the low beams to remain on or the high
beams to flash or dazzle pedestrians or
vehicles ahead. In such a case, it is neces-
sary to manually change between the
high beams and low beams.
• When there are lights similar to head-
lights or tail lights in the surrounding area
• When headlights or tail lights of vehicles
ahead are turned off, dirty, changing
color, or not aimed properly
• When the headlights are repeatedly
changing between the high beams and
low beams.
• When use of the high beams is inappro-
priate or when the high beams may be
flashing or dazzling pedestrians or other
drivers.
• When the vehicle is used in an area in
which vehicles travel on the opposite side
of the road of the country for which the
vehicle was designed, for example using
a vehicle designed for right-hand traffic in
a left-hand traffic area, or vice versa
• When it is necessary to disable the sys-
tem P.215
• Situations in which the sensors may not
operate properly P.218
■ Temporarily reducing front camera sen-
sitivity
The sensitivity of the front camera can be
temporarily reduced.
1 Turn the power switch off with the fol-
lowing conditions met.
● The headlight switch is in or
position.
● The headlight switch lever is in the low
beam position.
● The Automatic High Beam switch is on.
2 Turn the power switch to ON.
3 Within 60 seconds after performing
step
2, push the headlight switch lever
to the high beam position then pull it to
the original position quickly 10 times,
then leave the lever in the original posi-
tion.
4 If the sensitivity is changed, the Auto-
matic High Beam indicator will blink 3
times.
■ Changing to the high beams
Push the lever forward.
The AHB indicator will turn off and the
high beam indicator will turn on.
Pull the lever to its original position to
enable the Automatic High Beam system
Turning the high beams on/off
manually
203
4-3. Operating the lights and wipers
4
Driving
again.
■ Changing to the low beams
Press the Automatic High Beam
switch.
The AHB indicator will turn off.
Press the switch to enable the Automatic
High Beam system again.
It is recommended to switch to the low
beams when use of the high beams is
inappropriate or when the high beams
may cause problems or distress to
other drivers or pedestrians nearby.
Pull the lever rearward and then return it to
its original position.
The high beams will illuminate while the
lever is pulled, however, after the lever is
returned to its original position, the low
beams will remain on for a certain amount
of time. After this, the Automatic High
Beam system will operate.
Temporarily changing to the low
beams
204
4-3. Operating the lights and wipers
*
: If equipped
1
*1
or
*2
Turns the fog
lights off
2
Turns the fog lights on
*1
: For the U.S.A.
*2
: For Canada
■ Fog lights can be used when
The headlights are on in low beam.
Fog light switch
*
When in difficult driving conditions,
such as in rain and fog, turn on the
fog lights to secure front visibility.
Turning on the fog light
NOTICE
■ To prevent 12-volt battery discharge
Do not leave the lights on longer than
necessary when the hybrid system is off.
205
4-3. Operating the lights and wipers
4
Driving
Operating the lever operates
the wipers or washer as follows:
Intermittent windshield wipers with
interval adjuster
1
*1
or
*2
Off
2
*1
or
*2
Intermittent
operation
3
*1
or
*2
Low speed oper-
ation
4
*1
or
*2
High speed oper-
ation
5
*1
or
*2
Temporary oper-
ation
*1
: For the U.S.A.
*2
: For Canada
Wiper intervals can be adjusted when
intermittent operation is selected.
6
Increases the intermittent wind-
shield wiper frequency
7
Decreases the intermittent wind-
shield wiper frequency
8
Washer/wiper dual opera-
tion
Pulling the lever operates the wipers and
washer.
The wipers will automatically operate a
couple of times after the washer squirts.
Windshield wipers and
w
asher
Operating the lever can change
wiper operation to automatic/man-
ual or squirt washer fluid.
NOTICE
■ When the windshield is dry
Do not use the wipers, as they may dam-
age the windshield.
Operating the wiper lever
206
4-3. Operating the lights and wipers
Vehicles with headlight cleaners:
When the power switch is in ON and the
headlights are on, if the lever is pulled, the
headlight cleaners will operate once. After
this, the headlight cleaners will operate
every 5th time the lever is pulled.
Rain-sensing windshield wipers
When AUTO is selected, the wipers
will operate automatically when the
sensor detects falling rain. The system
automatically adjusts wiper timing in
accordance with rain volume and vehi-
cle speed.
1
*1
or
*2
Off
2 Rain-sensing operation
3
*1
or
*2
Low speed oper-
ation
4
*1
or
*2
High speed oper-
ation
5
*1
or
*2
Temporary oper-
ation
*1
: For the U.S.A.
*2
: For Canada
When AUTO is selected, the sensor
sensitivity can be adjusted by turning
the switch ring.
6 Increases the sensitivity
7 Decreases the sensitivity
8 Washer/wiper dual opera-
tion
Pulling the lever operates the wipers and
washer.
The wipers will automatically operate a
couple of times after the washer squirts.
(After operating several times, the wipers
operate once more time after a short delay
to prevent dripping. However, the dripping
prevention does not operate while the
vehicle is moving.)
Vehicles with headlight cleaners: When
the power switch is in ON and the head-
lights are on, if the lever is pulled, the head-
light cleaners will operate once. After this,
the headlight cleaners will operate every
207
4-3. Operating the lights and wipers
4
Driving
5th time the lever is pulled.
■ The windshield wipers and washer can
be operated when
The power switch is in ON.
■ Using the voice control system (if
equipped)
The following operations can be performed
using the voice control system:
● Operating the windshield wipers only
once
● Operating the windshield cleaning
washer (it can be performed only when
the vehicle is stopped)
For details regarding the voice control sys-
tem, refer to “MULTIMEDIA OWNER’S
MANUAL”.
■ Effects of vehicle speed on wiper opera-
tion (vehicles with rain-sensing wind-
shield wipers)
Vehicle speed affects the Intermittent wiper
interval.
■ Raindrop sensor (vehicles with rain-
sensing windshield wipers)
● The raindrop sensor judges the amount
of raindrops.
An optical sensor is adopted. It may not
operate properly when sunlight from the
rising or setting of the sun intermittently
strikes the windshield, or if bugs, etc. are
present on the windshield.
● If the wiper switch is turned to the AUTO
position while the power switch is in ON,
the wipers will operate once to show that
AUTO mode is activated.
● If the temperature of the raindrop sensor
is 194°F (90°C) or higher, or 5°F (-
15°C) or lower, automatic operation may
not occur. In this case, operate the wipers
in any mode other than AUTO mode.
■ If no windshield washer fluid sprays
Check that the washer nozzles are not
blocked, if there is washer fluid in the
washer fluid tank.
■ Front door opening linked windshield
wiper stop function
When AUTO is selected and the wind-
shield wipers are operating, if a front door is
opened, the operation of the windshield
wipers will be stopped to prevent anyone
near the vehicle from being sprayed by
water from the wipers, provided the vehicle
is stopped with the parking brake applied or
the shift position in P. When the front door
is closed, wiper operation will resume.
WARNING
■ Caution regarding the use of wind-
shield wipers in AUTO mode (vehi-
cles with rain-sensing windshield
wipers)
The windshield wipers may operate
unexpectedly if the sensor is touched or
the windshield is subject to vibration in
AUTO mode. Take care that your fin-
gers, etc. do not become caught in the
windshield wipers.
■ Caution regarding the use of washer
fluid
When it is cold, do not use the washer
fluid until the windshield becomes warm.
The fluid may freeze on the windshield
and cause low visibility. This may lead to
an accident, resulting in death or serious
injury.
NOTICE
■ When the washer fluid tank is empty
Do not operate the switch continually as
the washer fluid pump may overheat.
■ When a nozzle becomes blocked
In this case, contact your Lexus dealer.
Do not try to clear it with a pin or other
object. The nozzle will be damaged.
208
4-3. Operating the lights and wipers
When the windshield wipers are not
being used, they retract to below the
hood. To enable the windshield wipers
to be lifted when parking in cold condi-
tions or when replacing a windshield
wiper insert, change the rest position of
the windshield wipers to the service
position using the wiper lever.
■ Raising the wipers to the service
position
Within approximately 45 seconds of
turning the power switch off, move the
wiper lever to the (U.S.A.) or
(Canada) position and hold it for
approximately 2 seconds or more.
The wipers will move to the service posi-
tion.
■ Lifting the windshield wipers
While holding the hook portion of
the wiper arm, lift the windshield wiper
from the windshield.
■ Lowering the windshield wipers to the
retracted position
With the windshield wipers placed on the
windshield, turn the power switch to ON
and then move the wiper lever to an operat-
ing position. When the wiper switch is
turned off, the windshield wipers will stop at
the retracted position. Even if the wipers
deviate while the power switch is OFF, the
wipers will return to the normal position.
NOTICE
■ To prevent 12-volt battery discharge
Do not leave the wipers on longer than
necessary when the hybrid system is off.
Changing the windshield wiper
rest position/Lifting the wind-
shield wipers
A
209
4-3. Operating the lights and wipers
4
Driving
■ Using the voice control system (if
equipped)
The windshield wipers can be moved to the
service position using the voice control sys-
tem.
(Operation is possible only when the vehi-
cle is stopped with the wiper switch in
*1
or
*2
)
For details regarding the voice control sys-
tem, refer to the “MULTIMEDIA
OWNER’S MANUAL”.
*1
: For the U.S.A.
*2
: For Canada
Operating the switch operates
the rear wiper as follows:
1
*1
or
*2
Off
2
*1
or
*2
Intermittent
operation
3
*1
or
*2
Normal operation
*1
: For the U.S.A.
*2
: For Canada
NOTICE
■ When lifting the windshield wipers
● Do not lift the windshield wipers when
they are in the retracted position
below the hood. Otherwise, they may
contact the hood, possibly resulting in
damage to a windshield wiper and/or
the hood.
● Do not lift a windshield wiper by the
wiper blade. Otherwise, the wiper
blade may be deformed.
● Do not operate the wiper lever when
the windshield wipers are lifted. Oth-
erwise, the windshield wipers may
contact the hood, possibly resulting in
damage to the windshield wipers
and/or hood.
Rear window wiper and
w
asher
The rear window wiper and washer
can be used by operating the lever.
NOTICE
■ When the rear window is dry
Do not use the wiper, as it may damage
the rear window.
Operating the wiper lever
210
4-3. Operating the lights and wipers
4 Washer/wiper dual opera-
tion
Pushing the lever operates the wiper and
washer.
The wiper will automatically operate a cou-
ple of times after the washer squirts.
■ The rear window wiper and washer can
be operated when
The power switch is in ON.
■ Using the voice control system (if
equipped)
The following operations can be performed
using the voice control system:
● Operating the rear window wiper only
once
● Operating the rear window cleaning
washer (it can be performed only when
the vehicle is stopped)
For details regarding the voice control sys-
tem, refer to “MULTIMEDIA OWNER’S
MANUAL”.
■ If no windshield washer fluid sprays
Check that the washer nozzles are not
blocked, if there is washer fluid in the
washer fluid tank.
■ Reverse-linked rear window wiper
function
When the shift position is shifted to R while
the front wipers are operating, the rear win-
dow wiper will operate once.
■ Back door opening linked rear window
wiper stop function
When the rear window wiper is operating, if
the back door is opened while the vehicle is
stopped, operation of the rear window
wiper will be stopped to prevent anyone
near the vehicle from being sprayed by
water from the wiper. When the back door
is closed, wiper operation will resume.
*
*
: The setting must be customized at your
Lexus dealer.
■ Customization
Setting of the reverse-linked function can
be changed. (Customizable fea-
tures:P.460
NOTICE
■ When the washer fluid tank is empty
Do not operate the switch continually as
the washer fluid pump may overheat.
■ When a nozzle becomes blocked
In this case, contact your Lexus dealer.
Do not try to clear it with a pin or other
object. The nozzle will be damaged.
■ To prevent 12-volt battery discharge
Do not leave the wiper on longer than
necessary when the hybrid system is off.

Related Topics

Popular Owner Manuals