2019-2026 Lexus UX SUV Operating the lights and wipers -> AHB (Automatic High Beam) User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Operating the lights and wipers -> AHB (Automatic High Beam) for Your Lexus UX SUV First Generation (2019-2026)

201
4-3. Operating the lights and wipers
4
Driving
1 Press the Automatic High Beam
switch.
2
Turn the headlight switch to the
or position.
When the headlight switch lever is in the
low beam position, the AHB system will be
enabled and the AHB indicator will illumi-
nate.
■ Automatic operating conditions of the
high beams
● When all of the following conditions are
met, the high beams will illuminate auto-
matically:
• The vehicle speed is approximately 21
mph (34 km/h) or more.
• The area ahead of the vehicle is dark.
• There are no vehicles ahead with lights
on.
• There are few streetlights or other lights
on the road ahead.
● If any of the following conditions are met,
the headlights will change to the low
beams:
• Vehicle speed drops below approxi-
mately 17 mph (27 km/h).
• The area ahead of the vehicle is not dark.
• There is a vehicle ahead with lights on.
• There are many streetlights or other
lights on the road ahead.
■ Front camera detection
● In the following situations, the high beams
may not be automatically changed to the
low beams:
• When a vehicle cuts in front of your vehi-
cle
• When another vehicle crosses in front of
the vehicle
• When vehicles ahead are repeatedly
detected and then hidden due to
repeated curves, road dividers or road-
side trees
• When a vehicle ahead approaches from
a far lane
• When a vehicle ahead is far away
AHB (Automatic High
B
eam)
The Automatic High Beam uses a
front camera located on the upper
portion of the windshield to detect
the brightness of the lights of vehi-
cles ahead, streetlights, etc., and
automatically changes the head
lights between the high beams and
low beams.
WARNING
■ For safe use
Do not overly rely on the Automatic
High Beam. Always drive safely, taking
care to observe your surroundings and
turning the high beams on or off manu-
ally if necessary.
■ To prevent unintentional operation of
the Automatic High Beam system
When it is necessary to disable the sys-
tem P.215
Using the Automatic High Beam
system
202
4-3. Operating the lights and wipers
• When a vehicle ahead has no lights
• When the lights of a vehicle ahead are
dim
• When a vehicle ahead is reflecting strong
light, such as own headlights
• Situations in which the sensors may not
operate properly P.218
● The headlights may change to the low
beams if a vehicle ahead that is using fog
lights without its headlights turned on is
detected.
● House lights, street lights, traffic signals,
and illuminated billboards or signs may
cause the high beams to change to the
low beams, or the low beams to remain
on.
● The following may change the timing at
which the headlights change to the low
beams:
• The brightness of lights of vehicles ahead
• The movement and direction of vehicles
ahead
• The distance between the vehicle and a
vehicle ahead
• When a vehicle ahead only has lights illu-
minated on one side
• When a vehicle ahead is a two-wheeled
vehicle
• The condition of the road (gradient,
curve, condition of the road surface, etc.)
• The number of passengers and amount of
luggage
● The headlights may change between the
high beams and low beams unexpect-
edly.
● Bicycles and other small vehicles may not
be detected.
● In the following situations, the system may
not be able to correctly detect the bright-
ness of the surroundings. This may cause
the low beams to remain on or the high
beams to flash or dazzle pedestrians or
vehicles ahead. In such a case, it is neces-
sary to manually change between the
high beams and low beams.
• When there are lights similar to head-
lights or tail lights in the surrounding area
• When headlights or tail lights of vehicles
ahead are turned off, dirty, changing
color, or not aimed properly
• When the headlights are repeatedly
changing between the high beams and
low beams.
• When use of the high beams is inappro-
priate or when the high beams may be
flashing or dazzling pedestrians or other
drivers.
• When the vehicle is used in an area in
which vehicles travel on the opposite side
of the road of the country for which the
vehicle was designed, for example using
a vehicle designed for right-hand traffic in
a left-hand traffic area, or vice versa
• When it is necessary to disable the sys-
tem P.215
• Situations in which the sensors may not
operate properly P.218
■ Temporarily reducing front camera sen-
sitivity
The sensitivity of the front camera can be
temporarily reduced.
1 Turn the power switch off with the fol-
lowing conditions met.
● The headlight switch is in or
position.
● The headlight switch lever is in the low
beam position.
● The Automatic High Beam switch is on.
2 Turn the power switch to ON.
3 Within 60 seconds after performing
step
2, push the headlight switch lever
to the high beam position then pull it to
the original position quickly 10 times,
then leave the lever in the original posi-
tion.
4 If the sensitivity is changed, the Auto-
matic High Beam indicator will blink 3
times.
■ Changing to the high beams
Push the lever forward.
The AHB indicator will turn off and the
high beam indicator will turn on.
Pull the lever to its original position to
enable the Automatic High Beam system
Turning the high beams on/off
manually
203
4-3. Operating the lights and wipers
4
Driving
again.
■ Changing to the low beams
Press the Automatic High Beam
switch.
The AHB indicator will turn off.
Press the switch to enable the Automatic
High Beam system again.
It is recommended to switch to the low
beams when use of the high beams is
inappropriate or when the high beams
may cause problems or distress to
other drivers or pedestrians nearby.
Pull the lever rearward and then return it to
its original position.
The high beams will illuminate while the
lever is pulled, however, after the lever is
returned to its original position, the low
beams will remain on for a certain amount
of time. After this, the Automatic High
Beam system will operate.
Temporarily changing to the low
beams

Related Topics

Popular Owner Manuals