Get Emergency Information Guide for Mg HS SUV First Generation (2018-2023

Emergency Information

270 Hazard Warning Devices

272 eCall - SOS Emergency Assistance

274 Emergency Starting

276 Vehicle Recovery

280 Tyre Repair

287 Fuse Replacement

294 Bulb Replacement

5

EMERGENCY INFORMATION

Hazard Warning Devices

Hazard Warning Lamps

causing an obstruction or is in a hazardous situation.

Remember to switch them off before driving away.

Warning Triangle

Note: Before you stop or slow the vehicle in an

emergency, always press the hazard warning switch.

All turn signal lamps and direction indicators will ﬂash

together to warn other road users when your vehicle is

The warning triangle supplied with your vehicle is stowed

in the loadspace.

If you have to stop your vehicle on the road in

an emergency, you must place

a

warning triangle

270

EMERGENCY INFORMATION

approximately 50 — 150 metres behind the vehicle, if

possible, to warn other road users of your position.

5

271

EMERGENCY INFORMATION

eCall - SOS Emergency Assistance

the eCall triggers, the system will only transmit the data

information to the relevant public safety answering points

designated by the respective public authorities of the

country on which territory they are located, which will

receive and process your emergency call request. The

system will retain data locally within 13 hours of triggering.

In an accident, your vehicle’s eCall – SOS Emergency

Assistance can either be triggered manually or in severe

cases automatically upon detection by vehicle’s sensors.

The eCall service is a public service of general interest and

is accessible free of charge. The emergency call centre will

establish verbal communication with the vehicle occupants

in order to understand the extent of the emergency and

the level of assistance required. If verbal communication

is not achievable an attempt will be made to send the

following vehicle information message to the emergency

call centre. The appropriate emergency services will be

deployed to the vehicle’s current location if known.

You have the right to access the data information stored

in this system, and to request the rectiﬁcation, erasure

or blocking of data information that does not meet the

requirements of the regulations. When you think your

personal data is infringed, you have the right to complain

to the competent data protection authority.

For manual activation, press and release the SOS button

in the overhead console for 1 second to activate an

emergency services call. A single beep will be heard when

the eCall is triggered and a message will be displayed on

the vehicle’s message centre and entertainment player. The

entertainment player will be muted whilst the emergency

services call is active. Manually triggered emergency

services calls may be cancelled by pressing and releasing

the SOS button again within 5 seconds of the initial press,

two beeps will be heard conﬁrming that the emergency

•

Current time, location and direction of travel

Vehicle type

Vehicle identiﬁcation number (VIN)

Whether the call was automatically or manually initiated

Vehicle category

This system will ensure that your personal data is securely

protected. It is designed to ensure that it is not traceable

and other external systems are not available . When

272

EMERGENCY INFORMATION

services call has been cancelled and the messages will be

removed.

ﬂash slowly if a fault is detected. Faults detected during the

self-test will be displayed on the vehicles message centre.

Note: The operation of eCall - SOS Emergency

Assistance relies on cellular coverage and may be

affected by signal outages or low signal strength.

Note: The automatic emergency services call (eCall)

function may be disabled by the local MG Authorised

Repairer upon request.

5

The emergency services call (eCall) system will perform a

self-test when the ignition is turned ON. During a Self-Test

the emergency services call (eCall) LED status indicator on

the SOS button will ﬂash quickly until completion. The LED

status indicator will be illuminated solid if no system faults

are present. The LED status indicator will be extinctd or

273

EMERGENCY INFORMATION

Emergency Starting

Using Booster Cables

Starting the Vehicle

Ensure that each booster cable connection is

securely made. There must be no risk of the

clips accidentally slipping from the battery

terminals (as a result of engine vibration, for

example), this could cause sparking, which

could lead to ﬁre or explosion.

NEVER start the engine by pushing or towing.

Make sure that BOTH batteries are of the

same voltage (12 volts), and that the booster

cables are approved for use with 12 volt car

batteries.

Ensure sparks and naked lights are kept well

away from the engine compartment.

Using booster cables (jump leads) from a donor battery,

or a battery ﬁtted to a donor vehicle, is the only approved

method of starting a car with a ﬂat battery.

If the battery from a donor vehicle is to be used, the

vehicles should be parked with their battery locations

adjacent to one another. Ensure that the two vehicles do

not touch.

274

EMERGENCY INFORMATION

Ensure the START/STOP switch is turned off and switch off

ALL electrical equipment of BOTH vehicles, then follow the

instructions below:

shutting down the engine of the donor vehicle and

disconnecting the booster cables.

IMPORTANT

1

Connect the RED booster cable between the positive

(+) terminals of both batteries. Connect the BLACK

booster cable from the negative (-) terminal of the

donor battery (A) to a good earth point (an engine

mounting or other unpainted surface, for example), at

least 0.5 m from the battery on the disabled vehicle

(B).

NEVER turn on any electrical equipment on the

started vehicle before removing the booster cables.

5

Disconnecting the booster cables must be an exact

reversal of the procedure used to connect them, i.e.

disconnect the BLACK cable from the earth point on

the disabled vehicle FIRST.

2

3

Check that the cables are clear of moving parts of both

engines, then start the engine of the donor vehicle and

allow it to idle for a few minutes.

5

Now start the engine of the vehicle with the

discharged battery (DO NOT crank the engine for

more than 10 seconds). If the disabled vehicle will

not start after several attempts, it may need to be

repaired. Please contact the MG Authorised Repairer.

4

After both the vehicles have normally started, allow

the engines to idle for more than 2 minutes before

275

EMERGENCY INFORMATION

Vehicle Recovery

Towing for Recovery

Towing Eye

DO NOT use a tow rope that is twisted - or the towing hook may be unscrewed.

276

EMERGENCY INFORMATION

Your car is equipped with 2 towing eyes (located at the

front and the rear of the vehicle), which are used for

ﬁtting the towing hook in the tool kit. The tool kit is

placed beneath the loadspace ﬂoor. To ﬁt the towing hook,

remove the small cover set into the bumper, then screw

the towing hook via the small hole into the threaded hole

in the bumper beam (see illustration). Ensure the towing

hook is fully tightened!

Suspended Towing

If your vehicle needs to be towed, most qualiﬁed recovery

specialists will use wheel lift equipment to suspend the

vehicle. Please keep the driving wheels off the ground.

Ensure the parking brake is released, the hazard warning

lamps are activated and no passengers are left in the vehicle.

Note: The small cover removed may be secured to the

bumper by a plastic cord.

Both towing points are intended for using by qualiﬁed

recovery specialists to assist in the recovery of your

vehicle when a breakdown or accident occurs. They are

not designed for towing other vehicles, and must NEVER

be used to tow a trailer or caravan. The vehicle can be

towed using a tow rope but a towing bar is recommended.

5

Towing

When towing, DO NOT suddenly accelerate

or brake suddenly, this can cause accidents.

277

EMERGENCY INFORMATION

Four-Wheel Touchdown Towing

6

DO NOT tow backward with front wheels (drive

wheels) on the ground.

If, due to an electrical fault, it is considered

unsafe to switch the start/stop switch on, the

car will need to be recovered on a trailer.

The towing speed of the vehicle shall

，

not exceed 20mph (30km/h) the towing

distance shall not exceed 30miles (50km).

If your vehicle is towed with the four wheels on the ground,

observe the following precautions:

1

Operate the start/stop switch to the ON/RUNNING

position, this will enable the brake lights, wipers and

direction indicators to be operated if necessary.

2

3

4

5

Place the shift lever in Neutral (N).

Release the parking brake.

Without the engine running, greater effort will be required

to operate the brake pedal and turn the steering wheel.

Longer stopping distances will also be experienced.

Turn on the hazard warning lamps.

If the transmission is damaged or is subject to a lack

of lubricating oil, DO NOT tow the vehicle with four

wheels on the ground.

278

EMERGENCY INFORMATION

Transporter

2

3

Place the wheel chock (1) as shown in the ﬁgure,

then place the anti slip rubber pad (2) around the

circumference of the tyre.

If your vehicle needs to be shipped, a special transporter

is recommended. Secure the vehicle on the transporter as

follows:

Fit the lashing straps (3) around the wheels and secure

to the trailer. Tighten the straps until your vehicle is

securely held.

5

1

Apply the parking brake, manual transmission places

the shift lever in Neutral (N), automatic transmission

places the shift lever in Park (P).

279

EMERGENCY INFORMATION

Tyre Repair

1 Remove the label at the bottom of the repair ﬂuid

Tool Identiﬁcation (including tyre repair

tool)

reservoir and attach it to the steering wheel to remind

the driver not to exceed 50 mph（80 km/h）.

2

Connect the air hose of the electric air pump to the

repair ﬂuid reservoir. Invert the repair ﬂuid reservoir

on the groove of the electric air pump. Remove the

valve dust cap of the damaged tyre, and connect the

hose connector of the repair ﬂuid reservoir to the

1

2

3

4

Towing Hook

Wheel Bolt Cap Removal Tool

Electric Air Pump

Repair Fluid Reservoir

280

EMERGENCY INFORMATION

tyre valve. Check if the power switch of the electric

air pump is off (with "O pressed), then connect the

electric air pump plug to the 12V power socket in the

centre console, and switch on the start/stop switch.

3

Switch on the power switch of the electric compressor

(i.e., press “-”), to start pumping sealant into the

tyre. The tyre sealant bottle will become empty after

approximately 30 seconds. The tyre should reach the

speciﬁed pressure within 5 to 10 minutes.

Note: The pressure gauge may brieﬂy reach 6

bar (87 psi), then the pressure begins to drop to

normal.

4

When the required pressure is reached, switch off the

power switch of the electric compressor (i.e., press

“O”).

5

Note:

If the required pressure cannot be

reached within 10 minutes, please disconnect the

compressor, drive the vehicle 10 metres (33 feet)

approx forward or backward to allow the sealant

to spread within the tyre. If the required pressure

can still not be reached, the tyre is severely

damaged and you should seek assistance from an

MG Authorised Repairer.

Note:

To avoid battery discharge, it is

recommended to keep the engine running.

281

EMERGENCY INFORMATION

Note: Continued use of the electric air pump

for more than 10 minutes may result in motor

overheat and damage.

the tyre valve, and connect the plug of the electric air

pump to the power socket, then switch on the electric

air pump to inﬂate the tyre until it reaches the required

pressure. Repeat the operations of step 6 after driving

a maximum distance of 3 miles (5 km).

5

6

Remove the tyre sealant bottle from the slot in the

compressor, disconnect the hose from the tyre valve,

remove the compressor plug from the centre console

power socket, return the tyre repair kit to its stowage

tray.

After successfully adding sealant to the tyre, drive

immediately for a short time (around one minute) this

will allow the sealant to distribute evenly inside the

tyre. Continue driving and do not exceed 50 mph (80

km/h). After a further 10 minutes, ﬁnd a safe place to

stop and recheck the tyre pressure.

Please take different measures based on the tyre pressure

measured:

•

If the tyre pressure has dropped to less than 0.8

bar (11.6 psi), do not continue driving, seek an MG

Authorised Repairer for assistance instead.

•

If the tyre pressure has not dropped, you may continue

driving, but the vehicle speed must not exceed 50 mph

(80 km/h), and the driving mileage must not exceed 125

miles (200 km).

•

If the tyre pressure is between 0.8 bar (11.6 psi) and 2.3

bar (33.3 psi), connect the hose of electric air pump to

282

EMERGENCY INFORMATION

*

Note: DO NOT remove foreign objects (eg. screws,

nails) from the tyre. The tyre repair system must only

be used when the foreign object is in the tread pattern

(A), DO NOT attempt a repair when the damage is in

the sidewall of the tyre (B).

Changing a Wheel

If you need to change the wheel during the journey, choose

a safe place to stop away from the main road if possible.

Always ask your passengers to get out of the car and wait

in a safe area away from other trafﬁc.

Switch on hazard warning lamps. If available, position

a warning triangle about 50 to 150 metres behind your

vehicle to warn approaching trafﬁc.

Before changing a wheel, ensure the front wheels are in the

straight ahead position. Apply the parking brake and place

the gear shift lever in Park（P）.

5

Observe the following precautions:

•

Ensure the jack is positioned on ﬁrm, level ground.

If the vehicle must be parked on the hill, place chocks

in front of and behind other 3 wheels to prevent the

vehicle moving.

283

EMERGENCY INFORMATION

Positioning the Jack

NEVER work beneath the car with the jack

as the only means of support. The jack is

designed for wheel changing only!

NEVER jack the car using any positions other

than the jacking points. Serious damage to

the car could result.

Avoid accidental contact with any underbody

parts, especially hot exhaust system

components.

Position the jack on ﬁrm level ground under the jacking

point nearest the wheel to be removed. Note that the

domed head of the jack must ﬁt into the corresponding

recess in the sill plate (There is a triangle indicator in the

area shown by the arrowhead. See the illustration below).

Turning the jack screw handle by hand, adjust the jack until

the jack head ﬁts snugly onto the ﬂanging of the body.

Ensure that the base of the jack is in full contact with the

level ground.

284

EMERGENCY INFORMATION

Fitting the Spare Wheel

Regularly check the spare wheel tyre

pressure, it may be underpressure due to

unused for long periods of time. After

Note: Avoid placing wheels face down on the

ground - the surface may be scratched.

5

Fit the spare wheel and tighten the wheel bolts with

wheel bolt spanner until the wheel is seated ﬁrmly

against the hub.

replacement, at the ﬁrst opportunity check

and adjust the tyre pressure.

6

7

Lower the car and remove the jack, then FULLY tighten

the wheel bolts in a diagonal sequence.

The wheel bolts must be tightened to the

Finally, return the tools to the tool kit, put the tool kit

into the boot, tighten the retaining bolts, put down the

luggage carpet and put the replaced wheel above the

carpet (wheel rim face up).

speciﬁed torque after changing

a

wheel

～

(120 130 Nm).

1

Before raising the car, use the special tool supplied

with the vehicle to remove each wheel bolt cap. Use

the wheel bolt spanner to slacken each bolt half a turn

anti-clockwise.

5

Note: DO NOT stand on the handle of the wheel bolt

spanner or use extension tube on the handle of the

spanner.

2

3

Turn the handle in a clockwise direction until the tyre

is clear of the ground.

Note: When replacing the wheel, please fully tighten

the bolts in the diagonal sequence twice.

Remove the wheel bolts and place them in the tool kit

to prevent them from being lost. Make sure the vehicle

is steady and there is no risk of slip or movement

before removing wheel bolts.

Note: Contact an MG Authorised Repairer to replace

with a new tyre urgently.

4

Remove the road wheel.

285

EMERGENCY INFORMATION

Spacesaver Spare Wheel

car wash may conﬂict with the wheel/tyre and cause

damage.

Only one spacesaver spare wheel can be used

at any one time, otherwise the operational

performance and brake performance may be

reduced, thereby leading to accident or injury

to yourself and others.

When driving on icy or slippery surfaces it is

advised to ﬁt the spacesaver wheel to the rear

of the vehicle to maintain adaquate stability.

This may mean swapping a front wheel with

a rear wheel.

Snow chains can not be used on the

spacesaver spare wheel, this can cause

damage to the car and snow chain.

When the spacesaver spare wheel is ﬁtted, the vehicle

speed should not exceed 50 mph (80 km/h). Please have

the full-scale tyre repaired and replace the spare wheel as

soon as possible. This will extend the life span of the spare

wheel for other emergencies.

Note: DO NOT use an automatic car wash when

the spacesaver wheel is ﬁtted, the guide rails of the

286

EMERGENCY INFORMATION

Fuse Replacement

Fuse

Fuse Box

The vehicle is equipped with 2 fuse boxes:

Fuses are simple circuit breakers which protect the car’s

electrical equipment by preventing the electrical circuits

from being overloaded. A blown fuse may be indicated

when the item of electrical equipment it protect stops

working.

1

2

If a fuse is suspected faulty, you may remove it from the fuse

box and observe if the metal wire in the fuse is broken.

It is recommended to have spare fuses in the vehicle, which

can be obtained from a local MG Authorised Repairer.

5

IMPORTANT

•

NEVER attempt to repair a blown fuse. ALWAYS

replace a fuse with one of the same rating, otherwise

the ﬁre may be caused due to electrical system

damage or circuit overload.

1

2

Passenger compartment fuse box (behind the driver's

lower fascia panel)

Front compartment fuse box (nearside of the engine

compartment)

If a replaced fuse fails immediately, please contact an

MG Authorised Repairer as soon as possible.

287

EMERGENCY INFORMATION

Front compartment fuse box

4

If a fuse is blown, replace it with another fuse of the

same type and same ampere value.

Fuse Speciﬁcation

Code

F1

Specs

-

Function

-

F2

F3

10A

25A

-

Front Fog Lamp

F4

Body Control Module

F5

Body Control Module

Check or Replace a Fuse

-

F6

1

Turn the START/STOP Switch and all electrical

appliances OFF, and disconnect the battery negative

cable.

F7

10A

-

Engine Control Module

-

F8

2

3

Press the lock catch to open the upper cover of Front

compartment fuse box.

F9

15A

5A

-

Horn

F10

F11

Transmission Gear Shift Actuator

-

Hold the fuse head with the fuse extraction tool in the

upper cover, pull and remove the fuse, and check if the

fuse is blown.

288

EMERGENCY INFORMATION

Code

F12

Specs

25A

-

Function

Body Control Module

-

Code

F31–F35

F36

Specs

Function

-

10A

-

F13

A/C Compressor Relay

-

F14–F19

F20

F37

30A

-

DC-DC Converter

-

F38

15A

5A

-

Fuel Pump Relay

F21

F39

Crank Signal

-

F22–F23

F24

F40–F42

15A

30A

25A

Rear Wiper Relay

DC-DC Converter

Body Control Module

DC-DC Converter Relay, Fuel

Pump Relay, A/C Compressor

Relay, Clutch Position Sensor,

Brake Pedal Switch, Neutral

Position Sensor, Cooling Fan Relay

Box

5

F25

F43

F44

5A

F26

Windscreen/Rear

Washer Relay

Window

F27

10A

Electronic Thermostat,

Valve Intake, VVT Valve

Exhaust,

VVT

F28

F29

F30

25A

Super Lock Relay

-

15A

Upstream

Oxygen

Body Control Module

Front Wiper Relay

Sensor, Downstream Oxygen

Sensor, Canister Shut off Valve

289

EMERGENCY INFORMATION

Code

Specs

Function

Code

Specs

40A

Function

Engine Oil Control Valve, Canister

Control Valve, Exhaust Gas

Control Valve, Relief Valve

Dynamic Stability Control System

(valve)

MF1 D

F45

10A

-

MF1 E

MF1 F

MF1 G

MF1 H

MF2 K

MF2 L

F46

F47

15A

-

Engine Control Module

30A

-

Starter Relay

-

Ignition Coil, Air Flow Sensor

-

F48

50A

Cooling Fan

F49

10A

-

Right Headlamp

100A Passenger Compartment Fuse Box

30A

Electric Vacuum Pump

F50

Left Headlamp

-

F51–F56

Electric Power Steering Control

Module

MF1 A

MF1 B

MF1 C

80A

40A

7 -speed Dual Clutch Transmission

Control Module Relay

Dynamic Stability Control System

(pump)

290

EMERGENCY INFORMATION

Passenger Compartment Fuse Box

3

4

Hold the fuse head with the fuse extraction tool in

the Front compartment fuse box, pull and remove the

fuse, and check if the fuse is blown.

If a fuse is blown, replace it with another fuse of the

same type and same ampere value.

Fuse Speciﬁcation

Code

Specs

Function

Supplemental Restraint System

Sensing

Module,

and

DC-DC

Diagnostic

Converter,

5

F1

10A Communication Module, Shifter

Control Unit, Instrument Pack,

Body Control Module, SDM

Auxiliary Display Module

Check or Replace a Fuse

Transmission Control Module,

7.5A Reverse Lamp Switch, Engine

Control Module

1

Turn the START/STOP Switch and all electrical

appliances OFF, and disconnect the battery negative

cable.

F2

F3

2

Remove the lower trim panel at driver side to access

the fuse box.

Front View Camera Module,

5A

Forward Detection Radar

291

EMERGENCY INFORMATION

Code

F6–F7

F8

Specs

-

Function

Code

F24

F25

F26

F27

F28

F29

Specs

Function

-

10A Gateway

30A KLR Relay

15A Front Console Power Socket

F9

5A

-

USB Charging Port

-

30A Passenger Window Regulator

-

F10

F11

7.5A Heated Exterior Rearview Mirror

25A Heated Rear Window

5A

PEPS Control Unit, Spare Coil

F12

10A Gateway

-

F13–F14

F17

Driver Window Combination

Switch, Rain/Light Sensor

F30

5A

-

F31

F32

F18

30A Rear Left Window Regulator

5A EPB Switch, Gear Display

5A

Atmosphere Lamp Control Module

F19

Supplemental Restraint System

Sensing and Diagnostic Module

F33

F34

F35

5A

F20

30A Rear Right Window Regulator

10A Front Right Seat Heater Relay

F21

Communication Module

F22

5A

Data Link Connector

Digital Audio Broadcasting (DAB)

Module

10A

F23

10A Heated Front Left Seat

292

EMERGENCY INFORMATION

Code

F36

Specs

10A

Function

Code

F48

Specs

20A

Function

Electronic Steering Column Lock

Control Module

Front Passenger Power Seat

Adjustment

F37

F38

F39

F40

F41

F42

F43

F44

F45

F46

F47

20A Driver Power Seat Adjustment

30A Driver Window Regulator

30A Blower

F49

F50

30A Power Liftgate Control Module

-

Rear Window/Exterior Rearview

Mirror Heater Relay

F51

30A

15A Entertainment System

F52

F53

F54

10A KL15 Switch Relay

20A Shifter Control Unit

5A

Upper Centre Console Switch

10A HVAC Control Module

5

-

5A

Instrument Pack

Rear Driving Assist System

30A Sunroof Motor

5A

Tyre Pressure Monitoring System

30A Sunshade Motor

293

EMERGENCY INFORMATION

Bulb Replacement

Bulb Speciﬁcation

Bulb Replacement

Before replacing any bulb, ensure that the START/STOP

Switch and lighting switches are OFF so as to avoid any

possibility of a short circuit. When replacing the bulb,

actions shall be gentle so as not to damage the lamp.

Bulb

Type

Dipped Beam and Main

Beam (low conﬁguration)

HB3SL+ 60W

Note: Only replace bulbs with the same type and

speciﬁcation.

Front Indicator Lamps

(low conﬁguration)

WY21W 21W

H8 35W

Note: If the bulb glass is scratched or contaminated,

it may cause the bulb can not concentrate the light.

Take care NOT to touch the glass with your ﬁngers;

If necessary, clean the glass with methylated spirits to

remove ﬁngerprints.

Front Fog Lamps

Front Interior Lamps

(bulb conﬁguration)

W5W 5W

Consult an Authorised MG Repairer on speciﬁc

replacement operation.

Reverse Lamps

W16W 16W

W5W 5W

License Plate Lamps

Note: Bulb HB3SL+ is identical with HB3 in shape and

structure, and is only superior in reliability and service

life.

Note: Other light sources not included in the list are

LED , which cannot be replaced individually.

294

EMERGENCY INFORMATION

Dipped/Main Beam Headlamp Bulb Renewal

8

9

Locate the cover plug.

1

Open the bonnet——see “Bonnet” in the

“Maintenance” section.

Connect the negative battery terminal.

10 Test headlamp operation.

2

3

Disconnect the battery negative terminal.

11 Close the bonnet——see “Bonnet” in the

“Maintenance” section.

Identify and locate the headlamp bulb cover plug, and

remove it.

5

4

5

6

7

Rotate the bulb anti-clockwise and remove.

Remove the wiring connector from the bulb.

Reﬁt the wiring connector to the new bulb.

Locate the bulb in the lamp, rotate clockwise until fully

secured.

295

EMERGENCY INFORMATION

Front Indicator Lamp Bulb Renewal

9

Close the bonnet——see “Bonnet” in the

“Maintenance” section.

1

Open the bonnet——see “Bonnet” in the

“Maintenance” section.

2

3

Disconnect the battery negative terminal.

Rotate the bulb holder anti-clockwise and remove.

4

5

6

Remove the bulb from the holder.

Install new bulb into the holder.

Locate the bulb holder in the lamp, rotate clockwise

until fully secured.

7

8

Connect the negative battery terminal.

Test lamp operation.

296

EMERGENCY INFORMATION

Front Fog Lamp Bulb Renewal

5

6

7

Remove the wiring connector from the bulb holder.

Reﬁt the wiring connector to the new bulb holder.

1

Disconnect the battery negative terminal.

2

Safely raise and support the front of the vehicle with

suitable support equipment. DO NOT work under a

vehicle that is only supported by a scissor or trolley

jack.

Locate the bulb holder in the lamp, rotate clockwise

until fully secured.

8

9

Fit the bottom deﬂector.

Connect the negative battery terminal.

3

4

Remove the bottom deﬂector.

10 Test lamp operation.

Rotate the bulb holder anti-clockwise and remove.

5

297

EMERGENCY INFORMATION

Reverse Lamp Bulb Renewal

9

Test lamp operation.

1

Disconnect the battery negative terminal.

2

For reverse lamp bulb replacement, it is necessary to

remove the rear bumper cover, seek guidance from an

Authorised MG Repairer.

3

Rotate the bulb holder anti-clockwise and remove.

4

5

6

Remove the bulb from the holder.

Install new bulb into the holder.

Locate the bulb holder in the lamp, rotate clockwise

until fully secured.

7

8

Fit the rear bumper.

Connect the negative battery terminal.

298

EMERGENCY INFORMATION

License Plate Lamp Bulb Renewal

7

8

Install new bulb into the holder.

1

Open and support the tail gate——see “Alarm

Systems” in the “Starting and Driving” section.

Locate the bulb holder in the lamp, rotate clockwise

until fully secured.

2

3

4

Disconnect the battery negative terminal.

Remove the tail gate interior trim panel.

Remove the wiring connector of the lamp.

9

Reﬁt the wiring connector

10 Fit the tail gate interior trim panel.

11 Connect the negative battery terminal.

12 Close the tail gate.

13 Test lamp operation.

5

6

Rotate the bulb holder anti-clockwise and remove.

Remove the bulb from the holder.

299

EMERGENCY INFORMATION

Front Interior Lamp Bulb Renewal

assembly. Push the lens upwards until it ‘clicks’ into

position

1

Disconnect the battery negative terminal.

6

7

Connect the negative battery terminal.

Test lamp operation.

2

Use a small ﬂat-bladed screwdriver to gently prise the

lens from the lamp assembly.

3

4

5

Remove the bulb from its mounting to remove.

Install new bulb.

Install the lens, locate the two prongs at the front

of the lens and then carefully ﬂex the lens to locate

the two prongs at the rear of the lens into the lamp

300

Emergency Information for Your Mg HS SUV First Generation (2018-2023

Related Topics

Popular Owner Manuals

Latest Owner Manuals