2018-2023 Mg HS SUV Emergency Information -> Tyre Repair User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Emergency Information -> Tyre Repair for Your Mg HS SUV First Generation (2018-2023

EMERGENCY INFORMATION  
Tyre Repair  
Tyre Repair  
1 Remove the label at the bottom of the repair fluid  
Tool Identification (including tyre repair  
tool)  
reservoir and attach it to the steering wheel to remind  
the driver not to exceed 50 mph（80 km/h）.  
2
Connect the air hose of the electric air pump to the  
repair fluid reservoir. Invert the repair fluid reservoir  
on the groove of the electric air pump. Remove the  
valve dust cap of the damaged tyre, and connect the  
hose connector of the repair fluid reservoir to the  
1
2
3
4
Towing Hook  
Wheel Bolt Cap Removal Tool  
Electric Air Pump  
Repair Fluid Reservoir  
280  
EMERGENCY INFORMATION  
tyre valve. Check if the power switch of the electric  
air pump is off (with "O pressed), then connect the  
electric air pump plug to the 12V power socket in the  
centre console, and switch on the start/stop switch.  
3
Switch on the power switch of the electric compressor  
(i.e., press “-”), to start pumping sealant into the  
tyre. The tyre sealant bottle will become empty after  
approximately 30 seconds. The tyre should reach the  
specified pressure within 5 to 10 minutes.  
Note: The pressure gauge may briefly reach 6  
bar (87 psi), then the pressure begins to drop to  
normal.  
4
When the required pressure is reached, switch off the  
power switch of the electric compressor (i.e., press  
“O”).  
5
Note:  
If the required pressure cannot be  
reached within 10 minutes, please disconnect the  
compressor, drive the vehicle 10 metres (33 feet)  
approx forward or backward to allow the sealant  
to spread within the tyre. If the required pressure  
can still not be reached, the tyre is severely  
damaged and you should seek assistance from an  
MG Authorised Repairer.  
Note:  
To avoid battery discharge, it is  
recommended to keep the engine running.  
281  
EMERGENCY INFORMATION  
Note: Continued use of the electric air pump  
for more than 10 minutes may result in motor  
overheat and damage.  
the tyre valve, and connect the plug of the electric air  
pump to the power socket, then switch on the electric  
air pump to inflate the tyre until it reaches the required  
pressure. Repeat the operations of step 6 after driving  
a maximum distance of 3 miles (5 km).  
5
6
Remove the tyre sealant bottle from the slot in the  
compressor, disconnect the hose from the tyre valve,  
remove the compressor plug from the centre console  
power socket, return the tyre repair kit to its stowage  
tray.  
After successfully adding sealant to the tyre, drive  
immediately for a short time (around one minute) this  
will allow the sealant to distribute evenly inside the  
tyre. Continue driving and do not exceed 50 mph (80  
km/h). After a further 10 minutes, find a safe place to  
stop and recheck the tyre pressure.  
Please take different measures based on the tyre pressure  
measured:  
•
If the tyre pressure has dropped to less than 0.8  
bar (11.6 psi), do not continue driving, seek an MG  
Authorised Repairer for assistance instead.  
•
If the tyre pressure has not dropped, you may continue  
driving, but the vehicle speed must not exceed 50 mph  
(80 km/h), and the driving mileage must not exceed 125  
miles (200 km).  
•
If the tyre pressure is between 0.8 bar (11.6 psi) and 2.3  
bar (33.3 psi), connect the hose of electric air pump to  
282  

Related Topics

Emergency Information
Hazard Warning Lamps Warning Triangle eCall - SOS Emergency Assistance Emergency Starting Using Booster Cables Starting the Vehicle Vehicle Recovery Towing for Recovery Transporter Tool Identification (including tyre repair tool) Changing a Wheel Fuse Replacement Fuse Fuse Box Bulb Replacement Bulb Specification

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot