2004-2009 Nissan Micra 4 Door Monitor, Heater and air conditioner, and audio system -> Audio system (if equipped) User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Monitor, Heater and air conditioner, and audio system -> Audio system (if equipped) for Your Nissan Micra 4 Door Third Generation (2004-2009)

Air conditioner filter (if equipped)
GUID-54721F9E-94E1-4415-942D-E40E02F5EFE3
The air conditioner system is equipped with an air
conditioner filter which collects pollen. To make sure
the air conditioner heats defo gs, and ventilates
efficiently, replace the filter according the specified
maintenance intervals listed in a separate maintenance
booklet. To replace the filter, contact a NISSAN dealer.
The filter should be replaced if the air flow decreases
significantly or if windows fog up easily when operating
the heater or air conditioner.
GUID-121E5959-8B59-469A-A2B2-CEC8C9953337
AUDIO OPERATION PRECAUTIONS
GUID-FE28C7B7-A9FC-4E4E-8C0E-BFC08D6010D8
WARNING:
Do not adjust the audio system while driving so
that full attention may be given to vehicle
operation.
Radio
GUID-5802243A-184 F-45A1-84DE-A4B8AC50C97F
. Radio reception is affected b y statio n signal
strength, distance from radio transmitter, build-
ings, bridges, mountains and other external
influences. Intermittent changes in reception
quality normally are caused by these external
influences.
. Using a cellular phone in or near the vehicle may
influence radio reception quality.
Compact Disc (CD) player
GUID-68F3B02B-1FFC-4137-8E67-8B218FA1314A
. During cold weather or rainy days, the player may
malfunction due to the humidity. If this occurs,
remove the CD from CD player and dehumidify or
ventilate the player completely.
. The player may skip while driving on rough roads.
. The CD player sometimes may not function when
the passenger compartment temperature is ex-
tremely high. Lower the temperature before use.
. Do not expose the CD to direct sunlight.
. CDs that are of po or quality, or are dirty,
scratched, covered with fingerprints, or that have
pin holes may not work properly.
. The following CDs may not work properly.
— Copy control compact discs (CCCD)
— Recordable compact discs (CD-R)
— Rewritable compact discs (CD-RW)
SAA0480
. Do not use the following CDs as they may cause
the CD player to malfunction.
— 8 cm (3.1 in) discs (except for FM-AM Radio
with Compact Disc Player (Type B))
— CDs that are not round
— CDs with a paper label
— CDs that are warped, scratched or hav e
unusual edges.
— CD lens cleaner discs
. This audio system can only play prerecorded CDs.
It has no capabilities to record or burn CDs.
Monitor, Heater and air conditioner, and audio system 4-11
AUDIO SYSTEM (if equipped)
4-12 Monitor, Heater and air conditioner, and audio system
. If the CD cannot be played, one of the following
messages will be displayed.
Check disc/CHK CD/CD ERROR Check Disk:
. Confirm that the CD is inserted correctly (the label
side is facing up, etc.).
. Confirm that the CD is not bent or warped and it is
free of scratches.
. Confirm that the disc is a CD and not a DVD.
. Confirm that the disc contains audio files.
Push eject/Eject CD/CD Ejecting...:
This is a malfunction due to the temperature inside the
player is too high. Remove the CD by pushing the
EJECT button, and after a short time reinsert the CD.
The CD can be played when the temperature of the
player returns to normal.
Unplayable (model with type A, B, C audio unit):
The file is unplayable in this audio system (only MP3 or
WMA CD).
USB (Universal Serial Bus) (if equipped)
GUID-5962C464-893B-4736-9FD6-1FBC2FF2C655
WARNING:
Do not connect or disconnect the USB device
while driving. Doing so can be a distraction. If
distracted you could lose control of your vehicle
and cause an accident or serious injury.
CAUTION:
. Do not force the USB device into the USB
port. Inserting the USB device tilted or up-
side-down into the port may damage the
USB device and the port. Make sure that the
USB device is connected correctly into the
USB port.
. Do not grab the USB port cover (if equipped)
when pulling the USB device out of the port.
This could damage the port and the cover.
. Do not leave the USB cable in a place where
it can be pulled unintentionally. Pulling the
cable may break the wire, USB device or the
port.
. To avoid damage and loss of function when
using a USB device, note the following
precautions.
— Do not bend the cable excessively (40
mm (1.6 in) radius minimum).
— Do not twist the cable excessively (more
than 180 degrees).
— Do not pull or drop the cable.
— Do not hit or press the USB port or USB
device with hands, feet, or objects.
— Do not store objects with sharp edges in
the storage area where the c a b l e is
stored.
— Do not leave the USB device and
attached devices in the vehicle compart-
ment. When not in use for extended
periods of time, store the cable and USB
device in a clean, dust free environment
at room temperature and without direct
sun exposure.
— Do not use the cable for any other
purposes than its intended use in the
vehicle.
The vehicle is not equipped with a USB device. USB
devices should be purchased separately as necessary.
This system cannot be used to format USB devices. To
format a USB device, use a personal computer.
In some states/area, the USB device for the front seats
plays only sound wit hout images for regulatory
reasons, even when the vehicle is parked.
This system supports various USB memory devices,
USB hard drives and iPod players (if equipped). Some
USB devices may not be supported by this system.
. Partitioned USB devices may not be played
correctly.
. Some characters used in other languages (Chi-
nese, Japanese, etc.) are not displayed properly
on display. Using English language characters
with a USB device is recommended.
General notes for USB use:
. The USB device may not function whe n the
passenger compartment temperature is extremely
high. Lower the temperature before use.
. During cold weather or rainy days, the player may
malfunction due to humidity. If this occurs, remove
the USB device and dehumidify or ventilate the
USB player completely.
. Do not connect a USB device if a connector,
cable or USB port is wet. Allow the connector,
cable, and USB port to dry completely before
connecting the USB device. (Wait for 24 hours or
more until it is dry.) If the connector and USB port
are exposed to fluids other than water, evaporative
residue may cause a short circuit between the
connector pins and USB port. In this case, replace
the cable and USB port. Otherwise damage to the
USB device and a loss of function may occur.
. If the cable is damaged (insulation cut, connectors
cracked, contamination such as liquids, dust, dirt,
etc. in the connectors), do not use the cable.
Replace the cable with a new one.
. Do not put a USB device in a location where static
electricity occurs, electrical noise is generated or
hot air from the air conditioner blows directly on it.
Doing so may cause the data stored on the USB
device to be corrupted.
Notes for iPod use (if equipped):
iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
. Improperly plugging in the iPod may cause a
checkmark to be displayed on and off (flickering).
Always make sure that the iPod is connected
properly.
. An iPod nano (1st Generation) may remain in fast
forward or rewind mode if it is connected during a
seek operation. In this case, please manually reset
the iPod.
. An iPod nano (2nd Generation) will continue to
fast-forward or rewind if it is disconnected during
a seek operation.
. An incorrect song title may appear when the Play
Mode is changed while using an iPod nano (2nd
Generation)
. Audiobooks may not play in the same order as
they appear on an iPod.
. Large video files cause slow responses in an iPod.
The vehicle center display may momentarily black
out, but will soon recover.
. If an iPod automatically selects large video files
while in the shuffle mode, the vehicle center
display may momentarily black out, but will soon
recover.
Bluetooth
®
Audio player (if equipped)
GUID-1290AA2C-8C46-4510-BEB2-EE7D857CB85A
. Some Bluetooth
®
audio devices may not be used
with this system. For detailed information about
Bluetooth
®
audio devices that are available for use
with this system, contact a NISSAN dealer.
. Before using a Bluetooth
®
audio system, the initial
registration process for the audi o device is
necessary.
. Operation of the Bluetooth
®
audio system may
vary dep ending on the audio device that is
connec ted. Confirm the operation proc edure
before use.
. The playback of Bluetooth
®
audio will be paused
under the following conditions. The playback will
be resumed after the following conditions are
completed.
— while using a Hands-free phone
— while checking a connection with a cellular
phone
. The in-vehicle antenna for Bluetooth
®
commu-
nication is built in the system. Do not place the
Bluetooth
®
audio device in an area surrounded by
metal, far away from the system or in a narrow
space where the device closely contacts the body
or the seat. Otherwise, sound degradation or
connection interference may occur.
. While a Bluetooth
®
audio device is connected
through the Bluetooth
®
wireless connection, the
battery power of the device may discharge quicker
than usual.
. This system is compatible with the Bluetooth
®
AV
profile (A2DP and AVRCP).
Bluetooth
®
is a trademark owned
by Bluetooth SIG, Inc., and li-
censed to Daewoo IS Corp.
Compact Disc / USB memory device with
MP3 or WMA (if equipped)
GUID-4B589A86-B59B-43D5-8BBD-29B138FC39CB
Explanation of terms:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
. MP3 — MP3 is short for Moving Pictures Experts
Group Audio Layer 3. MP3 is the most well known
compressed digital audio file format. This format
allows for near “CD quality” sound, but at a
fraction of the size of normal audio files. MP3
conversion of an audio track from CD can reduce
the file size by approximately 10:1 ratio (Sampling:
44.1 kHz, Bit rate: 128 kbps) with virtually no
perceptible loss in quality. MP3 compression
removes the redundant and irrelevant parts of a
sound signal that the human ear doesn’t hear.
. WMA — Windows Media Audio (WMA) is a
compressed audio format created by Microsoft as
an alternative to MP3. The WMA codec offers
greater file compression than the MP3 codec,
enabling storage of more digital audio tracks in the
same amount of space when compared to MP3s
at the same level of quality.
. Bit rate — Bit rate denotes the number of bits per
second used by a digital music files. The size and
quality of a compre ssed digital audio file is
determined by the bit rate used when encoding
the file.
. Sampling frequency — The rate at which the
samples of a signal are converted from analog to
digital (A/D conversion) per second.
. Multisession — Multisession is one of the methods
for writing data to media. Writing data once to the
media is called a single session, and writing more
than once is called a multisession.
Monitor, Heater and air conditioner, and audio system 4-13
4-14 Monitor, Heater and air conditioner, and audio system
. ID3/WMA Tag — The ID3/WMA tag is the part of
the encoded MP3 or WMA file that contains
information about the digital music file such as
song title, artist, album title, encoding bit rate,
track time duration, etc. ID3 tag information is
displayed on the Album/Artist/Song title line on
the display.
* Windows
®
and Windows Media
®
are registered
trademarks and trademarks in the United States of
America and other countries of Microsoft Corporation
of the USA.
Playback order:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
SAA1025
Playback order chart
The music playback order of the CD with MP3 or
WMA is as illustrated.
. The names of folders not containing MP3 or WMA
files are not shown in the display.
. If there is a file in the top level of the disc, “Root
Folder” is displayed.
. The playback order is the order in which the files
were written by the writing software. Therefore,
the files might not play in the desired order.
Specification chart (model with type A, B, C audio unit):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Supported media CD, CD-R, CD-RW
Supported file systems
ISO9660 LEVEL1, ISO9660 LEVEL2, Romeo, Joliet
ISO9660 Level 3 (packet writing) is not supported.
Files saved using the Live File System component (on a Windows Vista-based computer)
are not supported.
Supported versions*1
MP3
Version MPEG1, MPEG2, MPEG2.5
Sampling frequency 8 kHz - 48 kHz
Bit rate 8 kbps - 320 kbps, VBR*4
WMA*3
Version WMA7, WMA8, WMA9
Sampling frequency 32 kHz - 48 kHz
Bit rate 32 kbps - 192 kbps, VBR*4
Tag information (Song title and Artist name)
ID3 tag VER1.0, VER1.1, VER2.2, VER2.3, VER2.4 (MP3 only)
WMA tag (WMA only)
Folder levels
Folder levels: 8, Folders: 255 (including route folder), Files: 512 (Max. 255 files for one
folder)
Displayable character codes*2
01: ASCII, 02: ISO-8859-1, 03: UNICODE (UTF-16 BOM Big Endian), 04: UNICODE
(UTF-16 Non-BOM Big Endian) , 05: UNICODE (UTF-8), 06: UNICODE (Non-UTF-16
BOM Little Endian)
*1 Files created with a combination of 48 kHz sampling frequency and 64 kbps bit rate cannot be played.
*2 Available codes depend on what kind of media, versions and information are going to be displayed.
*3 Protected WMA files (DRM) cannot be played.
*4 When VBR files are played, the playback time may not be displayed correctly. WMA7 and WMA8 are not applied to VBR.
Monitor, Heater and air conditioner, and audio system 4-15
4-16 Monitor, Heater and air conditioner, and audio system
Specification chart (model with type D, E, F audio unit):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Supported media CD, CD-R, CD-RW, USB2.0
Supported file systems
CD, CD-R, CD-RW: ISO9660 LEVEL1, ISO9660 LEVEL2, Romeo, Joliet
* ISO9660 Level 3 (packet writing) is not supported.
* Files saved using the Live File System component (on a Windows Vista-based computer) are
not supported.
USB memory device: FAT16, FAT32
Supported versions*1
MP3
Version MPEG1 Audio Layer 3
Sampling frequency 8 kHz - 48 kHz
Bit rate 8 kbps - 320 kbps, VBR*4
WMA*2
Version WMA7, WMA8, WMA9
Sampling frequency 32 kHz - 48 kHz
Bit rate 32 kbps - 192 kbps, VBR*4
Tag information (Song title and Artist name)
ID3 tag VER1.0, VER1.1, VER2.2, VER2.3, VER2.4 (MP3 only)
WMA tag (WMA only)
Folder levels
CD, CD-R, CD-RW
Folder levels: 8, Folders and files: 999 (Max. 255 files for one folder)
USB (model with type D
audio unit)
Folder levels: 8, Folders 255, Files: 65535 (Max. 999 files for one folder)
Memory size: 4GB
USB (model with type E, F
audio unit)
Folder levels: 8, Folders 255, Files: 2500 (Max. 255 files for one folder)
Memory size: 4GB
Displayable character codes*3
01: ASCII, 02: ISO-8859-1, 03: UNICODE (UTF-16 BOM Big Endian), 04: UNICODE (UTF-16
Non-BOM Big Endian), 05: UNICODE (UTF-8), 06: UNICODE (Non-UTF-16 BOM Little
Endian), 07: SHIFT-JIS
*1 Files created with a combination of 48 kHz sampling frequency and 64 kbps bit rate cannot be played.
*2 Protected WMA files (DRM) cannot be played.
*3 Available codes depend on what kind of media, versions and information are going to be displayed.
*4 When VBR files are played, the playback time may not be displayed correctly.
Troubleshooting guide (model with type A, B, C audio unit):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Symptom Cause and Countermeasure
Cannot play
Check if the disc was inserted correctly.
Check if the disc is scratched or dirty.
Check if there is condensation inside the player, and if there is, wait until the condensation is gone (about 1 hour) before using the
player.
If there is a temperature increase error, the CD player will play correctly after it returns to the normal temperature.
If there is a mixture of music CD files (CD-DA data), MP3/WMA files on a CD, only the music CD files (CD-DA data) will be played.
Files with extensions other than “.MP3”, “.WMA”, “.mp3” or “.wma” cannot be played. In addition, the character codes and number of
characters for folder names and file names should be in compliance with the specifications.
Check if the disc or the file is generated in an irregular format. This may occur depending on the variation or the setting of MP3/WMA
writing applications or other text editing applications.
Check if the finalization process, such as session close and disc close, is done for the disc.
Check if the disc is protected by copyright.
Poor sound quality Check if the disc is scratched or dirty.
It takes a relatively long time before
the music starts playing.
If there are many folder or file levels on the MP3/WMA disc, or if it is a multisession disc, some time may be required before the music
starts playing.
Music cuts off or skips
The writing software and hardware combination might not match, or the writing speed, writing depth, writing width, etc., might not
match the specifications. Try using the slowest writing speed.
Skipping with high bit rate files Skipping may occur with large quantities of data, such as for high bit rate data.
Move immediately to the next song
when playing.
When a non-MP3/WMA file has been given an extension of “.MP3”, “.WMA”, “.mp3, “.wma”, or when play is prohibited by copyright
protection, there will be approximately 5 seconds of no sound and then the player will skip to the next song.
The songs do not play back in the
desired order.
The playback order is the order in which the files were written by the writing software, so the files might not play in the desired order.
Monitor, Heater and air conditioner, and audio system 4-17
4-18 Monitor, Heater and air conditioner, and audio system
Troubleshooting guide (model with type D, E, F audio unit):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Symptom Cause and Countermeasure
Cannot play
Check if the disc or USB memory device was inserted correctly.
Check if the disc is scratched or dirty.
Check if there is condensation inside the player, and if there is, wait until the condensation is gone (about 1 hour) before
using the player.
If there is a temperature increase error, the player will play correctly after it returns to the normal temperature.
If there is a mixture of music CD files (CD-DA data) and compressed audio files on a CD, only the music CD files (CD-DA
data) will be played.
Files with extensions other than “.MP3 (.mp3)” or “.WMA (.wma)” cannot be played. In addition, the character codes and
number of characters for folder names and file names should be in compliance with the specifications.
Check if the disc or the file is generated in an irregular format. This may occur depending on the variation or the setting of
compressed audio writing applications or other text editing applications.
Check if the finalization process, such as session close and disc close, is done for the disc.
Check if the disc or USB memory device is protected by copyright.
Poor sound quality
Check if the disc is scratched or dirty.
It takes a relatively long time before the music
starts playing.
If there are many folder or file levels on the disc or USB memory device, some time may be required before the music
starts playing.
Music cuts off or skips
The writing software and hardware combination might not match, or the writing speed, writing depth, writing width, etc.,
might not match the specifications. Try using the slowest writing speed.
Skipping with high bit rate files Skipping may occur with large quantities of data, such as for high bit rate data.
Move immediately to the next song when playing.
If an unsupported compressed audio file has been given a supported extension like .MP3, or when play is prohibited by
copyright protection, the player will skip to the next song.
The songs do not play back in the desired order.
The playback order is the order in which the files were written by the writing software, so the files might not play in the
desired order.
Random/Shuffle may be active on the audio system or on a USB memory device.
ANTENNA (if equipped)
GUID-70C6C263-ACF5-46D4-8F17-91DC5DA13F75
JVH0390X
Adjust the antenna angle for the best reception.
Removing antenna
GUID-2D7BCF6A-4077-4BD0-ABA9-8BF62218818F
You can remove the antenna if necessary.
Hold the bottom of the antenna and remove by turning
counterclockwise.
To install the antenna, turn the antenna clockwise and
tighten.
CAUTION:
. Be sure to fold down the antenna before the
vehicle enters a garage with a low ceiling.
. Be sure that antenna is removed before the
vehicle enters an automatic car wash.
Monitor, Heater and air conditioner, and audio system 4-19
4-20 Monitor, Heater and air conditioner, and audio system
FM-AM RADIO WITH COMPACT DISC (CD) PLAYER (Type A)
GUID-D510DEF2-289A-40B2-B1DD-B8A7DA5F87FE
SAA3122
1. MUTE button
2. FM radio band select button
3. AM radio band select button
4. CD button
5. AUX button
6. CD EJECT button
7. MENU button
8. SEEK/TRACK button
9. TUNE/FF(Forward)·REW(Rewind)/FOLDER
button
10. SCAN button
11. RDM (Random) button
12. Power button/VOL (Volume) control knob
13. AUX IN (auxiliary input) jack
14. RPT (Repeat) button
15. AUTO.P (Automatic Preset) button
16. Radio memory buttons (1 - 6)
17. DISP (Display) button
4-22 Monitor, Heater and air conditioner, and audio system
Loading:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Insert a CD into the slot with the label side facing up.
The CD will be guided automatically into the slot and
will start playing. To stop playing, push the Power
button.
CAUTION:
Do not force the compact disc into the slot. This
could damage the player.
button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while a CD is loaded,
the CD will start playing automatically.
button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while a CD with a title
is being played, the display will change as follows:
CD:
NOS2417
CD with MP3 or WMA:
NOS2418
SEEK/TRACK button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while a CD is being
played, the present track will be advanced and move to
the next track. Push the
button several times to
skip forward tracks. The CD will advance the number
of times the button is pushed. When the last track of
the CD is forwarded, the first track will be played.
When the
button is pushed while a CD is being
played, the present track will start over from the
beginning of the current track. Push the
button
several times to skip back tracks. The CD will rewind
the number of times the button is pushed. When the
first track of the CD is rewound, the last track will be
played.
TUNE/FF·REW/FOLDER button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the or button is pushed and held
while a CD is being played, the CD will be played while
forwarding or rewinding. When the button is released,
the CD will return to the normal play speed.
When the
or button is pushed while a CD
with MP3 or WMA is being played, the first track in the
next or the previous folder will be played.
button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while a CD is being
played, the first 10 seconds of all the tracks will be
played.
When the
button is pushed again, the CD will
return to normal play from the track which is playing.
(Repeat) button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To change the play settings, push the button to
select the mode.
CD:
RPT DISC ? RPT TRACK
CD with MP3 or WMA:
RPT DISC ? RPT FOLDER ? RPT TRACK
RPT DISC:
All the tracks of the CD will be played continuously in
sequential order. The display indicates no symbol
mark. While the
button is pushed, the display
indicates “RPT DISC”.
RPT TRACK:
The selected track of the CD will be played con-
tinuously. While the
button is pushed, the display
indicates “RPT TRACK”.
RPT FOLDER:
All the tracks of selected folder wi ll be played
continuously in sequential order (CD with MP3 or
WMA only). While the
button is pushed, the
display indicates “RPT FOLDER”.
(Random) button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To change the play sequence, push the button to
select the mode.
CD:
RDM DISC ? RPT DISC
CD with MP3 or WMA:
RDM DISC ? RDM FOLDER ? RPT DISC
RPT DISC:
All the tracks of the CD will be played continuously in
sequential order. The display indicates no symbol
mark. While the
button is pushed, the display
indicates “RPT DISC”.
RDM DISC:
All the tracks or folders (CD with MP3 or WMA only) of
the CD will be played continuously in random order.
While the
button is pushed, the display indicates
“RDM DISC”.
RDM FOLDER:
All the tracks of the selected folder will be played
continuously in random order (CD with MP3 or WMA
only). While the
button is pushed, the display
indicates “RDM FOLDER”.
CD EJECT button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To eject a CD, push the CD EJECT button.
When the
button is pushed twice, the CD will be
ejected further, and the CD can be removed with ease.
If a CD is ejected by pushing the
button, and it is
not taken out from the loading slot, the CD will
automatically be reloaded to the slot to protect the CD
(12 cm discs only).
FM-AM radio operation
GUID-DF096F53-6064-4D10-B87D-721A74E9E378
SAA3123
The audio system operates when the ignition switch is
in the “ACC” or “ON” position.
/ button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the / button is pushed while the audio
system is off, the audio system will turn on and the
radio will turn on.
When the
/ button is pushed while another
audio source is playing, the another audio source will
turn off and the radio will turn on.
To change the radio bands, push the
/ button
until the desired band (FM1, FM2, AM) is displayed.
The FM stereo indicator, “ST” will display during FM
stereo reception. When the stereo broadcast signal is
weak, the radio will automatically change from stereo
to monaural reception.
TUNE/FF·REW/FOLDER button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When adjusting the broadcasting station frequency
manually, push the
or button until the desired
frequency is achieved.
When adjusting the broadcasting station frequency
automatically, push the
or button. When the
system detects a broadcasting station, it will stop at
the station.
SEEK UP/DOWN button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When adjusting the broadcasting station frequency
automatically, push the
button. When the
system detects a broadcasting station, it will stop at
the station.
button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed, the system will seek
and stop at the detected broadcasting station for 5
seconds, and then it will start to seek for the next
broadcasting station.
Push the
button in this 5-second period to stop
seeking.
Radio memory button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The audio system can store up to 12 FM station
frequencies (for FM1 and FM2) and 6 AM station
frequencies.
To store the station frequency:
1. Tune to the desired broadcasting station fre-
quency by using the
or button.
2. Push and hold a memory button (1 - 6) until a
beep sounds.
3. The switch number and frequency will appear on
the display when the memory is stored properly.
4. Perform steps 1 - 3 for all other memory buttons.
Push a memory button (1 - 6) to select a desired
memory.
If the battery cable is disconnected, or if the audio fuse
blows, the radio memory will be erased. In such a case,
reset the desired stations.
(Automatic Preset) button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The audio system can store up to 6 FM station
frequencies and 6 AM station frequencies.
To store the station frequency automatically, push and
hold the
button until a beep sounds. The station
will be automatically stored in the “AUTO.P” memory.
The display indicates “AP-**”.
Monitor, Heater and air conditioner, and audio system 4-23
4-24 Monitor, Heater and air conditioner, and audio system
Push the button to select a desired memory.
FM-AM RADIO WITH COMPACT DISC (CD) PLAYER (Type B)
GUID-DEAAE749-895D-46F1-A5DA-966300E348EA
JVH0003X
1. Sound preference button
2. TA (Traffic Announcement)/NEWS button
3. FM·AM band select button
4. CD button
5. AUX button
6. CD EJECT button
7. MENU button
8. SEEK/TRACK button
9. TUNE button
10. ENTER button
11. PHONE END/BACK button
12. POWER ON/OFF button/VOL UME control
knob
13. AUX IN (auxiliary input) jack
14. PHONE SEND button
15. PHONE BOOK button
16. Radio memory buttons
17. RPT (Repeat)/MIX (Mix play) button
Anti-theft system (if equipped)
GUID-7992F1A2-D71A-49A4-89B6-9A8B63656386
This unit can only be activated when the ignition switch
for NATS is in the “ACC” or “ON” position. Each radio
is uniquely matched to the vehicle’s immobilizer and
therefore cannot be transferred to any other vehicle.
Audio main operation
GUID-E4544D95-4AC4-49F3-8C6B-CF45CC7678F5
The audio system operates when the ignition switch is
in the “ACC” or “ON” position.
POWER ON/OFF button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To turn on the audio system, push the POWER ON/
OFF button.
. The system will turn on in the mode, (radio or CD)
which was used immediately before the system
was turned off.
. If there is no CD loaded, the radio will be turned
on.
To turn off the audio system, push the POWER ON/
OFF button.
Volume control:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To control the volume, turn the VOLUME control dial.
Turn the VOLUME control dial clockwise to make the
sound louder.
Turn the VOLUME control dial counterclockwise to
make the sound quieter.
Sound preference button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To enter the audio mode (radio or CD), push the
button. When no CD is loaded, the audio system will
automatically switch to the radio mode.
To change the audio settin gs (BASS, TREBLE,
FADER, BALANCE, EQ), push the
button or
ENTER button to select the mode.
BASS ? TREBLE ? BALANCE ? FADER ? EQ ?
BASS
To adjust each audio setting, turn the VOL control dial
clockwise or counterclockwise.
BASS: (−) to decrease / (+) to increase
TREB(LE): (−) to decrease / (+) to increase
BAL(ANCE): (R) to right balance / (L) to left balance
FADE(R): (F) to front fade / (R) to rear fade
EQ (Equalizer): Use this control to change the preset
sound mode for CD play.
Turn the MENU/VOL dial clockwise or counterclock-
wise. The mode will change as follows:
OFF Û ENHANCE
If the audio settings mode is unchanged for approxi-
mately 8 seconds, the audio sett ings mode will
automatically return to the normal mode.
MENU button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To configure the SPEED volume and BEEP settings,
perform the following procedure:
1. Push the MENU button.
2. Turn the VOLUME dial clockwise or counter-
clockwise. The display message will change as
follows:
PHONE SETUP ÛSPEED VOL Û CLOCK Û
BEEP Û PHONE SETUP
. When SPEED VOL appears on the display, briefly
push on the ENTER button then turn the VOLUME
dial clockwise or counterclockwise to adjust the
level of the volume.
Adjusting the setting to 0 (zero) turns off the
speed volume feature. Increa sing th e speed
volume setting results in the audi o volume
increasing more rapidly with vehicle speed. Push
the ENTER button again to save the setting.
. When BEEP appears on the display, briefly push
the ENTER button and then turn the VOLUME dial
clockwise or counterclockwise to switch the beep
sound on or off. Push the ENTER button again to
save the setting.
To configure Alternative Frequency, Regional an d
Language settings, perform the following procedure:
1. Push and hold the MENU button for at least 1.5
seconds.
2. Turn the VOLUME dial clockwise or counter-
clockwise. The display message will change as
follows:
AF Û REG Û LANGUAGE Û AF
. To activate or deactivate the AF and REG mode,
briefly push on the ENTER button when AF or
REG appears on the di splay and turn the
VOLUME dial clockwise or counterclockwise to
switch between the off or on position. After
selection, push the ENTER button to confirm the
settings.
— When the AF mode is enabled, the audio unit
will automatically re-tune to a stronger fre-
quency if the radio signal becomes weak.
— When the REG mode is enabled, the audio unit
will maintain and hold the station which is
broadcasting local (regional) programmes.
. To change the display language, briefly push the
ENTER button when LANGUAGE appears on the
display then turn the VOLUME dial clockwise or
counterclockwise to select the appropriate lan-
guage setting.
ENGLISH Û DUTCH Û FRENCH Û SPANISH
Û GERMAN Û ITALIAN Û PORTUGUESE Û
ENGLISH
After selecting the desired language, push the
Monitor, Heater and air conditioner, and audio system 4-25
4-26 Monitor, Heater and air conditioner, and audio system
ENTER button to exit the menu.
After the desired levels have been set, push the MENU
button to exit the menu or wait at least for 10 seconds
without pressing any buttons.
Clock :
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Clock display can be turned on and off, and clock can
be adjusted.
. When clock is not displayed
1. Turn the audio unit on by pushing the POWER
ON/OFF button.
2. Push the MENU button and turn the VOLUME
control knob until “CLOCK” is displayed.
3. Push the ENTER butt on. ( “CLOCK OFF” is
displayed)
4. Turn the VOLUME control knob to turn the clock
display mode on. (“CLOCK ON” is displayed)
5. Push the ENTER button. The hour display will start
flashing.
6. Turn the VOLUME control knob to adjust the time.
7. Push the ENTER button. The minute display will
start flashing.
8. Turn the VOLUME control knob to adjust the time.
9. Push the ENTER button to finish the clock
adjustment.
. When clock is displayed
1. Turn the audio unit on by pushing the POWER
ON/OFF button.
2. Push the MENU button and turn the VOLUME
control knob until “CLOCK” is displayed.
3. Push the ENTER button. (“CLOCK ON” is
displayed.)
4. Perform steps 5 to 9 above to adjust the time.
AUX button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The AUX IN jack is located on the audio unit. The AUX
IN audio input jack accepts any standard analog audio
input such as from a portable cassette tape/CD player,
MP3 player, laptop computers, etc.
Push the AUX button to play a compatible device when
it is plugged into the AUX IN jack.
Nissan strongly recommends using a stereo mini plug
cable when connecting your music device to the audio
system. Music may not play properly when a monaural
cable is used.
CD player operation
GUID-ABB6ED79-DF91-44C1-9FE5-85B2D4B17345
JVH0004X
The audio system operates when the ignition switch is
in the “ACC” or “ON” position.
Loading:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Insert a CD into the slot with the label side facing up.
The CD will be guided automatically into the slot and
will start playing. If the radio is already playing, it will
automatically turn off, and the CD will start playing.
CAUTION:
Do not force the CD into the slot. This could
damage the player.
After loading the CD, the number of tracks and the
playtime will appear on the display.
8 cm (3.1 in) diameter CDs can be played without
using an adapter.
CD button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while the audio
system is off and a CD is loaded, the audio system will
turn on and a CD will start playing automatically. If the
radio is already playing, it will automatically turn off and
the CD will start playing.
FF (Fast Forward), REW (Rewind)
button :
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the or button while a CD is being
played to fast-forward or rewind through the track.
When the button is released, the CD will return to
normal play speed.
TRACK UP/ DOWN button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while a CD is being
played, the present track will be advanced and move to
the next track. Push the
button several times to
skip forward tracks. The CD will advance the number
of times the button is pushed. When the last track of
the CD is forwarded, the first track will be played.
When the
button is pushed while a CD is being
played, the present track will start over from the
beginning. Push the
button several times to skip
back tracks. The CD will rewind the number of times
the button is pushed. When the first track of the CD is
rewound, the last track will be played.
Repeat/MIX button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the button repeatedly to change the play
mode as follows:
RPT (REPEAT) TRACK ? MIX DISC ? RPT
(REPEAT) ALL
RPT TRACK: The CD player plays the current track
continuously.
RPT ALL: All the tracks on the CD will be played in
sequential order.
MIX DISC: All the tracks on the CD will be played in a
random order.
CD EJECT button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while a CD is loaded,
the CD will be ejected.
When the
button is pushed twice, the CD will be
ejected further, and the CD can be removed with ease.
If a CD is ejected by pushing the
button, and it is
not taken out from the loading slot, the CD will
automatically be reloaded to the slot to protect the CD.
FM-AM radio operation
GUID-62577150-AB9A-4822-B2C1-0903FBA292E8
JVH0004X
The audio system operates when the ignition switch is
in the “ACC” or “ON” position.
FM-AM button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while the audio
system is off, the audio system will turn on and the
radio will turn on. When the
button is pushed
while CD is already operating, it will automatically turn
off, and the radio will turn on.
To change the radio bands, push the
button until
the desired band appears.
FM 1 ? FM 2 ? FM T ? MW ? LW
During FM reception, when the
button is pushed
for longer than 1.5 seconds, stations are searched for
and the 6 stations of the FM T band. The sound is
muted until the auto store operation is completed,
upon which preset channel 1 is automatically tuned in.
TUNE button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When adjusting the broadcasting station frequency
manually, push the
button until the desired
frequency is achieved.
The frequency changes in steps of 100 kHz on the FM
band, 9 kHz on the MW band, and 3 kHz on the LW
band.
SEEK button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When adjusting the broadcasting station frequency
automatically, push the
button. When the
system detects a broadcasting station, it will stop at
the station.
*
1
*
2
*
3
*
4
*
5
*
6
Radio memory buttons:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The audio system can store up to 18 FM station
frequencies (six in each of FM 1, FM 2 and FM T), 6
MW and 6 LW station frequencies.
To store the station frequency manually:
1. Tune to the desired broadcasting station fre-
quency by using the
or
button.
2. Push and hold a radio memory button
*
1
-
*
6
until a beep sounds. (The radio mutes when the
memory button is pushed.)
3. The channel indicator will display and the radio
mute disengages, indicating that the memory is
stored properly.
4. Perform steps 1 - 3 for all other memory buttons.
If the battery cable is disconnected, or if the audio fuse
blows, the radio memory will be erased. In such a case,
reset the desired stations.
Monitor, Heater and air conditioner, and audio system 4-27
4-28 Monitor, Heater and air conditioner, and audio system
Radio data system (RDS)
GUID-4A9782F1-308C-4422-8258-DBF1D2A91C68
Alternative Frequency (AF) :
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
. The AF function operates in the FM (radio) and CD
modes.
. When the AF mode is set to “ON” in the user
setup menu mode, the AF indicator illuminates.
For activation or deactivation details, see “Audio main
operation” (P.4-25).
. Automatic switching function
This function compares the strengths of the
signals of all the stations on the AF list and
selects the station with the optimum reception
conditions.
. Program Information (PI) search
Program Information (PI) search begins automati-
cally if no suitable station is found with the above
automatic switching function . The PI search
function checks each RDS station with the same
PI code. During this time the sound is muted and
“PI SEARCH” is displayed. The PI search opera-
tion stops when a suitable station is found. If no
station is found once all the frequencies have been
searc hed, the radio returns to the previou s
frequency.
. Enhanced Other Network (EON) data update
(This function also operates when the AF
mode is off.)
When EON data is being received, this enables
automatic retuning of other preset stations on the
same network. Also, network linked services can
be used. The EON indicator turns on during the
reception of RDS EON stations in the FM mode.
RDS functions:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
. Programme Service (PS) function (station
name display function)
When an RDS station is tuned in with seek or
manual tuning, the RDS data is received and the
Program Service (PS) name is displayed.
. Emergency broadcast interrupt function
(ALARM INTERRUPTION — EBU SPEC FOR
INFO)
When the radio receives PTY code 31 (an
emergency broadcast code), the sound is inter-
rupted, the emergency broadcast is heard, and
“PTY31 ALARM” is displayed. The volume level at
this time is the same as that for traffic announce-
ments. Once the emergency broadcast is finished,
the unit immediately returns to the previous
source.
. REG (Regional) mode
Some local radio stations are linked together
according to their region because they only offer
limited coverage due to their limited number of
transmitters. If the signal from one station be-
comes weak while you are driving around, RDS
mode will switch to another local station in the
region with a stronger signal.
When the REG mode is activated in the FM band
and the radio receiver is tuned to a local radio
station, it will keep receiving this radio station
without switching to another local station. For
activation or deactivation details, see “Audio main
operation” (P.4-25).
Traffic Announcement (TA):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
. The TA function operates in the FM and CD
modes.
. The TA mode is turned on or off when the TA/
NEWS button is pushed for less than 2 seconds.
. The TA mode operates regardless of whether the
AF mode is on or off.
. “TA ON” is displayed when the TA mode is turned
on, and the TA indicator turns on. “TA OFF” is
displayed when the TA mode is turned off, and the
TA indicator turns off.
The following function operates when the TA mode is
on:
. Traffic announcement interrupt function
When a traffic announcement is received, the
announcement is tuned in and the volume
increases to the set level.
Once the traffic announcement is finished, the unit
returns to the source which was set before the
traffic a nnouncement started, and the volume
returns to the previous level. For EON stations,
the radio is interrupted by another EON station
with traffic announcements.
The traff ic announcement interrupt mode is
cancelled if th e TA/NEWS button is pushed
during a traffic an nouncement. The TA mode
returns to the standby mode and the audio unit
returns to the previous source.
News mode:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the NEWS button or the TA/NEWS button is
pushed for longer than 2 seconds in the FM mode, the
news function is activated. “NEWS” is displayed for 3
seconds and the NEWS indicator appears on the
display.
When the news function is activated, the radio
receives a news code from the FM broadcasting news
station and the play mode will be interrupted. Once the
news broadcast is finished, the unit returns to the
previous mode.
In some countries or regions, th i s service is not
available or the signal is too weak to be received.
1. News standby mode
.
The news standby mode can be activated in
the FM or CD mode.
.
A news interruption will be announced and
“NEWS” will be displayed when the radio
detects the news code from the tuned station
or EON stations. The display will then change
to the PS name of the interrupting station.
.
When pushing the NEWS button or pushing
th e TA/NEWS button for lon ger than 2
seconds, the news standby mode is turned
off and the indicator disappears from the
display.
2. News interruption mode
.
When the NEWS button or the TA/NEWS
button is pushed during the news interruption
mode, the radio returns to the previous source.
However, the news standby mode is kept.
.
When the
button is pushed during the
news interruption mode, the radio changes to
the CD mode. However, the news standby
mode is kept.
If the radio band is changed to the MW or LW,
the news standby mode will be turned off.
FM-AM RADIO WITH COMPACT DISC (CD) PLAYER (Type C)
GUID-19188120-A5DD-467A-9930-69AB282576B0
JVH0200X
1. MUTE button
2. FM·AM radio band select button
3. CD button
4. Radio memory buttons
5. AUX button
6. CD EJECT button
7. DISP button
8. SEEK/TRACK/FILE button
9. SCAN button
10. RDM (Random) button
11. RPT (Repeat) button
12. Power button/Volume control knob
13. AUX IN (auxiliary input) jack
14. AUTO.P (Automatic Preset) button
15. SCRL (Scroll) button
16. TUNE/FF (Forward)·REW (Rewind)/FOLDER
button
Monitor, Heater and air conditioner, and audio system 4-29
Loading:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Insert a CD into the slot with the label side facing up.
The CD will be guided automatically into the slot and
will start playing. To stop playing, push the Power
button.
CAUTION:
Do not force the compact disc into the slot. This
could damage the player.
button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while a CD is loaded,
the CD will start playing automatically.
button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while a CD with a title
is being played, the display will change as follows:
CD:
NOS2417
CD with MP3 or WMA:
NOS2418
SEEK/TRACK/FILE button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button (located on the left side) is
pushed while a CD is being played, the present track
will be advanced and move to the next track. Push
the
button several times to skip forward tracks.
The CD will advance the number of times the button is
pushed. When the last track of the CD is forwarded,
the first track will be played.
When the
button is pushed while a CD is being
played, the present track will start over from the
beginning of the current track. Push the
button
several times to skip back tracks. The CD will rewind
the number of times the button is pushed. When the
first track of the CD is rewound, the last track will be
played.
TUNE/FF·REW/FOLDER button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the or button (located on the
right side) is pushed and held while a CD is being
played, the CD will be played while forwarding or
rewinding. When the button is released, the CD will
return to the normal play speed.
When the
button or is pushed while a
CD with MP3 or WMA is being played, the first track in
the next or the previous folder will be played.
button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while a CD is being
played, the first 10 seconds of all the tracks will be
played.
When the
button is pushed again, the CD will
return to normal play from the track which is playing.
(Repeat) button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To change the play settings, push the button to
select the mode.
CD:
RPT DISC ? RPT TRACK
CD with MP3 or WMA:
RPT DISC ? RPT FOLDER ? RPT TRACK
RPT DISC:
All the tracks of the CD will be played continuously in
sequential order. The display indicates no symbol
mark. While the
button is pushed, the display
indicates “RPT DISC”.
RPT TRACK:
The selected track of the CD will be played con-
tinuously. While the
button is pushed, the display
indicates “RPT TRACK”.
RPT FOLDER:
All the tracks of selected folder wi ll be played
continuously in sequential order (CD with MP3 or
WMA only). While the
button is pushed, the
display indicates “RPT FOLDER”.
(Random) button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To change the play sequence, push the button to
select the mode.
CD:
RDM DISC ? RPT DISC
CD with MP3 or WMA:
RDM DISC ? RDM FOLDER ? RPT DISC
RPT DISC:
All the tracks of the CD will be played continuously in
sequential order. The display indicates no symbol
mark. While the
button is pushed, the display
indicates “RPT DISC”.
RDM DISC:
All the tracks or folders (CD with MP3 or WMA only) of
the CD will be played continuously in random order.
While the
button is pushed, the display indicates
Monitor, Heater and air conditioner, and audio system 4-31
4-32 Monitor, Heater and air conditioner, and audio system
“RDM DISC”.
RDM FOLDER:
All the tracks of the selected folder will be played
continuously in random order (CD with MP3 or WMA
only). While the
button is pushed, the display
indicates “RDM FOLDER”.
(Scroll) button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the title is displayed but it is a long one, the
whole title is not shown in the display. In this case,
push the button to scroll the title. When the title is
scrolled to the end of it, the display will stop moving
and return to the first condition.
CD EJECT button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To eject a CD, push the CD EJECT button.
When the
button is pushed twice, the CD will be
ejected further, and the CD can be removed with ease.
If a CD is ejected by pushing the
button, and it is
not taken out from the loading slot, the CD will
automatically be reloaded to the slot to protect the CD
(12 cm discs only).
FM-AM radio operation
GUID-BC953870-C001-41D4-AC35-4C73F86C5B83
JVH0201X
The audio system operates when the ignition switch is
in the “ACC” or “ON” position.
Frequency range and step change (for Central/
South America):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To change the frequency range and step specification
of the radio, perform the following operations.
1. Turn the audio unit off by pushing the POWER
button.
2. Turn the audio unit on by pushing the POWER
button while pushing the radio memory buttons
and the button.
For Central/South America specification, the display
indicates “AM 530 kHz”.
For the other specification, the display indicates “AM
531 kHz”.
If you experience difficulties in changing radio speci-
fication, contact a NISSAN dealer.
button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while the audio
system is off, the audio system will turn on and the
radio will turn on.
When the
button is pushed while another audio
source is playing, the another audio source will turn off
and the radio will turn on.
To change the radio bands, push the
button until
the desired band is displayed.
. AM ? FM1 ? FM2
The FM stereo indicator, “ST” will display during FM
stereo reception. When the stereo broadcast signal is
weak, the radio will automatically change from stereo
to monaural reception.
TUNE/FF·REW/FOLDER button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When adjusting the broadcasting station frequency
manually, push the
or button until the
desired frequency is achieved.
When adjusting the broadcasting station frequency
automatically, push t he
or button.
When the system detects a broadcasting station, it
will stop at the station.
SEEK button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When adjusting the broadcasting station frequency
automatically, push the
button. When the
system detects a broadcasting station, it will stop at
the station.
button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed, the system will seek
and stop at the detected broadcasting station for 5
seconds, and then it will start to seek for the next
broadcasting station.
Push the
button in this 5-second period to stop
seeking.
Radio memory button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The audio system can store up to 12 FM station
frequencies (for FM1 and FM2) and 6 AM station
frequencies.
To store the station frequency:
1. Tune to the desired broadcasting station fre-
quency by using the
or button.
2. Push and hold a memory button (1 - 6) until a
beep sounds.
3. The switch number and frequency will appear on
the display when the memory is stored properly.
4. Perform steps 1 - 3 for all other memory buttons.
Push a memory button (1 - 6) to select a desired
memory.
If the battery cable is disconnected, or if the audio fuse
blows, the radio memory will be erased. In such a case,
reset the desired stations.
(Automatic Preset) button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The audio system can store up to 6 FM station
frequencies and 6 AM station frequencies.
To store the station frequency automatically, push and
hold the
button until a beep sounds. The station
will be automatically stored in the “AUTO.P” memory.
The display indicates “AP-**”.
Push the
button to select a desired memory.
FM-AM RADIO WITH COMPACT DISC (CD) PLAYER (Type D)
GUID-C5B9C7A9-DA96-4C91-B937-719DE16695BA
JVH0504X
1. CD eject button
2. MENU button
3. AUTO.P/DISP button
4. SCAN button
5. FM/AM band select button
6. MEDIA button
7. SEEK button
8. TRACK button
9. TUNE button
10. FOLDER button
11. Power/VOL dial
12. RDM button
13. Radio memory buttons
14. AUX IN jack
15. RPT button
16. USB connector
Monitor, Heater and air conditioner, and audio system 4-33
4-34 Monitor, Heater and air conditioner, and audio system
Audio main operation
GUID-B1112647-F5F0-4652-A1A3-253CDEE1121E
The audio system operates when the ignition switch is
in the “ACC” or “ON” position.
Power/VOL dial:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Power ON/OFF:
To turn on the audio system, push the
dial.
. The system will turn on in the mode, which was
used immediately before the system was turned
off.
. If a CD, a USB and/or an AUX device was
connected when the system was turned off, and if
the system was turned on again with the devices
disconnected, the radio will turn on.
To turn off the audio system, push the
dial.
Volume control:
To control the volume, turn the
dial.
Turn the
dial clockwise to make the sound louder.
Turn the
dial counterclockwise to make the sound
quieter.
MENU button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To change the audio settings, push the button to
select the mode.
Push the
button repeatedly until the desired mode
appears on the display.
(Normal) ? BAS (Bass) ? TRE (Treble) ? BAL
(Balance) ? FAD (Fader)? CLK (Clock) ? (Normal)
Push the
/ button or / button to
adjust the audio settings.
BAS: (−) to decrease / (+) to increase
TRE: (−) to decrease / (+) to increase
BAL: (R) to right balance / (L) to left balance
FAD: (F) to front fade / (R) to rear fade
Once the audio settings are set to the desired level,
push the
button until the normal audio display
appears.
If no action is performed for approximately 5 seconds,
the audio settings mode will automatically return to the
normal mode.
Clock display:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To display the clock on the screen, perform the
following operations.
1. Push the
button repeatedly until “CLK ON” or
“CLK OFF” appears on the display while the audio
system is on.
2. Push the
/ button or / button
to select “CLK ON”.
The clock display can be turned on or off temporarily
by pushing the
button.
Clock adjustment:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To adjust the clock, turn the clock display on and
perform the following operations.
1. Push the
button while "CLK ON" is on the
display. The hour digits blink.
2. To adjust the hours, push the
/ button or
/ button.
3. Push the
button again. The minute digits
blink.
4. To adjust the minutes, push the
/ button
or
/ button.
If no user input is detected for 5 seconds, or when the
button is pushed, the clock setting mode will
automatically return to the normal mode.
MEDIA button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push this button to switch the mode to CD, USB or
another AUX device.
When the
button is pushed with no device
connected, the audio system does not change modes.
AUX IN jack:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The AUX IN jack is located on the audio unit. The AUX
IN audio input jack accepts any standard analog audio
input such as from a portable cassette tape player, CD
player, digital audio player or laptop computer.
Push the
button to play a compatible device when
it is plugged into the AUX IN jack.
NISSAN strongly recommends using a stereo mini
plug cable when connecting your music device to the
audio system. Music may not play properly when a
monaural cable is used.
WARNING:
Do not allow the cable or an external device
connected to the AUX terminal to affect your
driving.
NOTE:
. Depending on the external device, please
note that the volume may be louder or
quieter than that of the external device.
. When the AUX contacts the plug of the
connector cable, noise may be heard.
. The connected external device cannot be
operated with the main audio system. The
volume and sound quality can be adjusted.
. The song title in the external device cannot
be displayed on the audio display.
. For the power source of the external device,
use the special battery. The external device
cannot be charged with the AUX terminal.
Noise may be heard if the CD, radio etc. is
operated while charging the battery with the
power socket of the vehicle.
CD player operation
GUID-F9879A46-FDA9-4558-B27E-F03F51ED19A9
JVH0505X
The audio system operates when the ignition switch is
in the “ACC” or “ON” position.
Loading:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Insert a CD into the slot with the label side facing up.
The CD will be guided automatically into the slot and
will start playing. To stop playback, push the
dial.
CAUTION:
Do not force the compact disc into the slot. This
could damage the player.
MEDIA button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To play a CD, push the button repeatedly while
the CD is loaded until the display changes to the CD
mode.
SEEK/TRACK buttons:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Fast forward/Rewind:
When the
or button is pushed and held
while a CD is being played, the CD will play while fast
forwarding or rewinding.
When the button is released, the CD will return to
normal play speed.
Track up/down:
To play the next track, push the
button while a CD
is playing.
To play the previous track, push the
button within
2 seconds after the current track starts playing. To
return to the beginning of the current track, push the
button after the current track has played for at
least 2 seconds.
TUNE/FOLDER buttons (for CD with
MP3/WMA):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To skip to the next or previous folder, push the or
button.
SCAN button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while a CD is being
played, the first 10 seconds of all the tracks will be
played.
When the
button is pushed again, the CD will
return to normal play from the track which is playing.
RPT button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the button to select the mode.
CD:
(Normal) ? RPT
CD with MP3 or WMA:
(Normal) ? Track RPT ? Folder RPT
Track RPT:
The selected track will play repeatedly.
Folder RPT (CD with MP3 or WMA only):
All the tracks in the selected folder will play repeatedly
in sequential order.
RDM button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the button to select the mode.
CD:
(Normal) ? RDM
CD with MP3 or WMA:
(Normal) ? Folder RDM ? All RDM
Folder RDM:
All the tracks in the selected folder will play repeatedly
in random order.
All RDM:
All the tracks on the selected CD will play in random
order.
CD Eject button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To eject a CD, push the button.
When the
button is pushed twice, the CD will be
ejected further and the CD can be removed with ease.
If a CD is ejected by pushing the
button, and it is
Monitor, Heater and air conditioner, and audio system 4-35
4-36 Monitor, Heater and air conditioner, and audio system
not taken out from the loading slot, the CD will
automatically be reloaded to the slot to protect the CD.
FM-AM radio operation
GUID-2CABA29F-23D3-4B25-BAF4-520694DF93AE
JVH0505X
The audio system operates when the ignition switch is
in the “ACC” or “ON” position.
FM/AM band select button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while the audio
system is off, the audio system and the radio will turn
on.
When the
button is pushed while another audio
source is playing, the other audio source will turn off
and the radio will turn on.
To change the radio bands, push the
button until
the desired band is displayed.
AM ? FM1 ? FM2
TUNE/FOLDER buttons:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When adjusting the broadcasting station frequency
manually, push the
or button until the
preferred frequency is achieved.
SEEK/TRACK buttons:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To adjust the broadcasting station frequency auto-
matically, push the
or button. When the
system detects a broadcasting station, it will stop at
that station.
SCAN button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed, the system will seek
and stop at the detected broadcasting station for 5
seconds, and then it will start to seek for the next
broadcasting station.
Push the
button in this 5-second period to stop
seeking.
(Radio memory) buttons:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The audio system can store up to 12 FM station
frequencies (for FM1 and FM2) and 6 AM station
frequencies.
To store the station frequency:
1. Tune to the desired broadcasting station fre-
quency.
2. Push and hold a memory button (
- ) until a
beep sounds.
3. The switch number and frequency will appear on
the display when the memory is stored properly.
4. Perform steps 1 - 3 for all other memory buttons.
Push a memory button (
- ) to select the desired
memory.
If the battery cable is disconnected, or if the audio fuse
blows, the radio memory will be erased. In this case,
reset the desired stations.
AUTO.P/DISP button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The audio system can store up to 6 FM station
frequencies and 6 AM station frequencies.
To store the station frequency automatically, push and
hold the
button until a beep sounds. The station
will be automatically stored in the “AUTO.P” memory.
The display indicates “AUTO.P”.
Push the
button to select a memory.
USB memory device operation
GUID-F36722B8-C758-4C99-9504-BBF16449E7C0
JVH0505X
Audio main operation:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The USB outlet connector is located on the audio unit.
Open the lid and connect a USB memory device into
the connector. The system switches to the USB mode
automatically.
If the system has been turned off while the USB
memory device was playing, pushing the
dial will
start playback of the USB memory device.
If the USB memory device cannot be played, the
message “CHK USB” will be displayed.
CAUTION:
. Do not force the USB memory device into
the USB port. Inserting the USB memory
device tilted or upside down into the port
may damage the USB memory device and/or
the port. Make sure that the USB memory
device is connected to the USB port cor-
rect ly. (Some USB devices come with a
mark as a guide. Make sure that the
mark is facing the correct direction before
inserting the device.)
. Do not place objects near the USB memory
device to prevent the objects from leaning
on the USB memory device and the port.
Pressure from the objects may damage the
USB memory device and/or the port.
MEDIA button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed with the system off
and the USB memory device is inserted, the system
will turn on.
If another audio source is playing and a USB memory
device is inserted, push the
button repeatedly
until the display changes to the USB mode.
SEEK/TRACK buttons:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the or button is pushed and held
while a USB memory device is being played, the USB
memory device will play while fast forwarding or
rewinding. When the button is released, the USB
memory device will return to normal play speed.
When the
or button is pushed while the USB
memory device is being played, the next track or the
beginning of the current track on the USB memory
device will be played.
TUNE/FOLDER buttons:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To change to another folder in the USB memory
device, push the
or button.
RPT button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while a USB memory
device is being pla yed, the play pattern can be
changed as follows.
(Normal) ? Track RPT ? Folder RPT ? (Normal)
RDM button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while a USB memory
device is being pla yed, the play pattern can be
changed as follows.
(Normal) ? Folder RDM ? All RDM ? (Normal)
SCAN button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while a USB memory
device is being played, the first 10 seconds of all the
tracks will be played.
When the
button is pushed again, the USB
memory device will return to normal play from the track
which is playing.
Monitor, Heater and air conditioner, and audio system 4-37
4-38 Monitor, Heater and air conditioner, and audio system
FM-AM RADIO WITH COMPACT DISC (CD) PLAYER (Type E)
GUID-537DAEF8-6D11-45DA-A235-B326DFF97FFF
JVH0506X
1. Day/Night button
2. FM button
3. RPT button
4. MIX button
5. Radio memory buttons
6. A-Z button
7. AM button
8. CD eject button
9. CD button
10. Power/VOL dial
11. Rewind button
12. Fast Forward button
13. DISP button
14. SETUP button
15. Back button
16. TUNE/MENU/ENTER dial
17. AUX button
Audio main operation
GUID-678E2E1F-C725-4EBE-BB98-AF681C7A4933
The audio system operates when the ignition switch is
in the “ACC” or “ON” position.
Power/VOL dial:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Power ON/OFF:
To turn on the audio system, push the
dial.
. The system will turn on in the mode that was used
immediately before the system was turned off.
. If a CD is inserted, or a USB and/or an AUX
device is connected when the system is turned off,
and if the system was turned on again with the
devices removed or disconnected, the radio will
turn on.
To turn off the audio system, push the
dial.
Volume control:
To control the volume, turn the
dial.
Turn the
dial clockwise to make the sound louder.
Turn the
dial counterclockwise to make the sound
quieter.
SETUP button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To configure Audio, Clock, Language or Scroll direc-
tion settings, perform the following procedure:
1. Push the
button.
2. Push the
dial.
3. Turn the
dial clockwise or counterclockwise.
The setting menu will be displayed in the following
order:
Audio Û Clock Û Language Û Scroll Direction
After the desired levels have been set, either push the
button repeatedly, push the button, or wait
for several seconds without pushing any buttons to exit
the menu screen.
Audio adjustments:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the button to enter the setup menu screen
and then select “Audio”.
Each time the
dial is pushed, the mode will
change as follows:
BASS ? TREBLE ? BALANCE ? FADE ? AUX
VOL ? Audio (setup menu screen) ? BASS
Turn the
dial clockwise or counterclockwise to
adjust the following items and push the
dial to
confirm.
Bass control:
Use this control to enhance or attenuate the bass
response sound.
Treble control:
Use this control to enhance or attenuate the treble.
Balance control:
Use this control to adjust the balance of the volume
between the left and right speakers.
Fader control:
Use this control to adjust the balance of the volume
between the front and rear speakers (if equipped).
AUX VOL (Auxiliary volume) control:
Use this control to adjust the volume output from the
auxiliary source.
Clock setting:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the button to enter the setup menu screen
and then select “Clock”.
Turn the
dial. The mode will change as follows:
Set Time Û ON/OFF Û Clock Format Û Set Time
Set Time:
Select “Set Time” and then adjust the clock as follows:
The hour display will start flashing. Turn the
dial to
adjust the hour and push the
dial. The minute
display will start flashing. Turn the
dial to adjust
the minute and push the
dial to finish the clock
adjustment.
ON/OFF:
Set the clock display to on or off when the audio unit is
turned off. If set in the “ON” position, the clock will be
displayed when the audio unit is turned off either by
pushing the
dial or when the ignition switch is
placed in the “OFF” position.
Clock Format:
Switch the clock display between 24-hour and 12-
hour clock mode.
Language setting:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the button to enter the setup menu screen
then select “Language”.
Select the appropriate language and push the
dial. Upon completion, the screen will automatically
adopt the language setting.
Scroll direction:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Set the scrolling behavior of the dial to scroll UP
or DOWN.
Day/Night button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the button to switch the display brightness
between the daytime and nighttime modes.
Monitor, Heater and air conditioner, and audio system 4-39
4-40 Monitor, Heater and air conditioner, and audio system
AUX button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the button to play a compatible device when
it is connected.
CD player operation
GUID-80E425E8-EB3D-4F08-8A79-A2D1ED6D6C24
JVH0507X
The audio system operates when the ignition switch is
in the “ACC” or “ON” position.
Loading:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Insert a CD into the slot with the label side facing up.
The CD will be guided automatically into the slot and
will start playing. After loading the CD, the number of
tracks and the playtime will appear on the display.
CAUTION:
Do not force the CD into the slot. This could
damage the player.
NOTE:
. The CD player accepts normal audio CDs or
CDs containing MP3/WMA files.
. The audio unit will automatically detect if a
CD containing MP3/WMA files is inserted,
and “MP3CD” will be displayed.
. An error notification message will be dis-
played when an incompatible disc is in-
serted (e.g. DVD), or if the player cannot
read the CD. Eject the disc and insert
another disc.
List view:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
While the track is being played, push either the
dial or the button to display the available tracks in
a listed view mode. Turn the
dial to select a track
from the list, or a track to start listening to, and then
push the
dial.
Quick search:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
In the list view mode, a quick search can be performed
to find a track from the list. Push the
button, turn
the
dial to the first alphabetic letter of the song
title and then push the
dial. When found, a list of
the available songs will be displayed. Select a song
and then push the
dial to start playback.
CD button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while the audio
system is turned off and a CD is loaded, the audio
syste m will turn on and a CD will start playing
automatically. If the radio or AUX source mode is
already playing, it will automatically turn off and the CD
will start playing.
However, if a CD is not loaded, then a notification
message will be displayed and the audio unit will
remain in the radio or AUX source mode.
Fast Forward/Rewind buttons:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push and hold the / buttons to fast forward
or rewind through the track. When the button is
released, the track will play at normal playing speed.
Track up/down:
By pushing the
/ buttons once, the track will
skip forward to the next track or backward to the
beginning of the current track. Push the
/
buttons more than once to skip through the tracks.
Folder browsing:
If the recorded media contains folders with music files,
pushing the
/ button will play the tracks of
each folder in sequence.
To select a preferred folder:
1. Push the
dial or button and a list of
tracks in the current folder will be displayed.
2. Push the
button.
3. Turn the
dial to highlight the preferred folder.
4. Push the
dial to access the folder. Push the
dial again to start playing the first track or
turn the
dial, and push the dial to select
another track.
If the current selected folder contains sub folders, push
the
dial, a new screen with a list of sub folders will
be displayed. Turn the
dial to highlight the sub
folder and then push the
dial to select. Select the
root folder item when songs are recorded additionally
in the root folder.
To return to the previous folder screen, push the
button.
RPT button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the button and the current track will be
played continuously.
MIX button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the button and all the tracks will be played in
random order.
DISP button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
While a CD with recorded music information tags (CD-
text/ID3-text tags) is being played, the title of the
played track is displayed. If the title information is not
provided then “Track” is displayed.
When the
button is pushed repeatedly, further
information about the track can be displayed along
with the track title as follows:
CD:
Track time ? Artist ? Song ? Album ? Track time
CD with MP3/WMA:
Track time ? Artist ? Album ? Folder name ? Track
time
Track details:
By pushing and holding the
button, the display
will show a detailed overview and after a few seconds
it will return to the main display. Push the
button
briefly to return to the main display immediately.
CD Eject button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while a CD is loaded,
the CD will be ejected.
When the
button is pushed twice, the CD will be
ejected further, so that the CD can be removed with
ease.
When the ignition switch is in the “OFF” or “LOCK”
position it is possible to eject the CD currently being
played. However the audio unit will not be activated.
If a CD is ejected by pushing the
button, and it is
not removed from the loading slot for some time, the
CD will automatically be reloaded to the slot to protect
the CD.
FM-AM radio operation
GUID-AB44D427-410B-43B3-B55F-23E489713FA7
The audio system operates when the ignition switch is
in the “ACC” or “ON” position.
FM/AM buttons:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the / button is pushed while the audio
system is off, the audio system will turn on and the
radio will turn on.
When the
/ button is pushed while another
audio source is playing, the other audio source will turn
off and the radio will turn on.
To change the radio band (FM1, FM2, or AM), push the
/ button.
ENTER dial:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When adjusting the broadcasting station frequency
manually, turn th e
dial until the preferred
frequency is achieved.
Fast Forward/Rewind buttons:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When adjusting the broadcasting station frequency
automatically, push the
/ button. When the
system detects a broadcasting station, it will stop at
the station.
*
1
*
2
*
3
*
4
*
5
*
6
(Radio memory) buttons:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
During radio reception, pushing the radio memory
button for less than 2 seconds will select the stored
radio station.
The audio system can store up to 18 FM station
frequencies (six in each of FM 1, FM 2 and FM T) and 6
AM station frequencies.
To store the station frequency manually:
1. Tune to the desired broadcasting station fre-
quency by using the
/ button.
2. Push and hold a radio memory button
*
1
-
*
6
until a beep sounds. (The radio mutes when the
memory button is pushed.)
3. The channel indicator will display and the radio
mute disengages, indicating that the memory is
stored properly.
4. Perform steps 1 - 3 for all other memory buttons.
If the battery cable is disconnected, or if the audio fuse
blows, the radio memory will be erased. If this occurs,
reset the desired stations.
USB memory device operation
GUID-8E460E2D-9E1B-4340-9B6F-53C238229B06
JVH0518X
Monitor, Heater and air conditioner, and audio system 4-41
4-42 Monitor, Heater and air conditioner, and audio system
Audio main operation:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The USB outlet connector is located on the instrument
panel. Open the lid and connect a USB memory device
to the connector. The system will switch to the USB
memory device mode automatically.
If the system is turned off while the USB memory
device is playing, pushing the
dial will start the
USB memory device.
If the USB memory device cannot be played, one of the
following messages will be displayed.
. “USB memory device not supported”
. “No audio file detected”
CAUTION:
. Do not force the USB memory device into
the USB port. Inserting the USB memory
device tilted or upside down into the port
may damage the USB memory device and/or
the port. Make sure that the USB memory
device is connected correctly into the USB
port. (Some USB devices come with a
mark as a guide. Make sure that the mark is
facing the correct direction before inserting
the device.)
. Do not place objects near the USB memory
device to prevent the objects from leaning
on the USB memory device and the port.
Pressure from the objects may damage the
USB memory device and/or the port.
AUX button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To operate the USB memory device use one of the
following methods:
. Push the
button and then turn the dial to
select the USB item. Once highlighted, push the
dial.
. Push the
button repeatedly until “USB” is
highlighted, and then push the
dial.
Audio main operation:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The following operations are identical to the audio main
operation of the Compact Disc (CD) operation. For
details, see “CD player operation” (P.4-40).
. List view
. Quick search
.
. MIX (Random play)
. RPT (Repeat track)
. Folder browsing
DISP button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
While a track with recorded music information tags
(ID3-tags) is being played, the title of the played track
will be displayed. If the tags are not provided, a
notification message will be displayed.
When the
button is pushed repeatedly, further
information about the track can be displayed along
with the track title as follows:
Track time ? Artist ? Album ? Folder name ? Track
time
Track details:
By pushing and holding the
button the display will
show a detailed overview and after a few seconds it
will return to the main display. Push the
button
briefly to return to the main display immediately.
iPod player operation
GUID-64BF1C53-C8 8A-43A7-97CD-7690A141CB38
Connecting iPod:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The USB outlet connector is located in the center
console. Open the USB outlet connector lid and
connect the iPod cable to the USB connector. The
battery of the iPod is charged while the device is
connected to the vehicle.
Depending on the version of the iPod, the display on
the iPod shows a NISSAN or Accessory Attached
screen when the connection is completed. When the
iPod is connected to the vehicle, the iPod music library
can only be operated by the vehicle audio controls.
* iPod and iPhone are trademarks of Apple Inc.,
registered in the U.S. and other countries.
CAUTION:
. Do not force the iPod cable into the USB
port. Inserting the iPod cable tilted or upside
down into the port may damage the iPod
cable and the port. Make sure that the iPod
cable is connected correctly into the USB
port. (Some iPod cables come with a
mark as a guide. Make sure that the mark is
facing the correct direction before inserting
the iPod cable.)
. Do not locate objects near the iPod cable to
prevent the objects from leaning on the iPod
cable and the port. Pressu re from the
objects may damage the iPod cable and
the port.
Compatibility:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The following models are supported:
. Third generation iPhone (Firmware version
IOS4/4.0)
. Fourt h genera tion iPhone (Firmware version
IOS4/4.0)
. Fifth generation iPod (Firmware version 1.3)
. First generation iPod Classic (Firmware version
1.1.1 or 1.1.2PC)
. Second generation iPod Classic (Firmware ver-
sion 2.0.1)
. First generation iPod touch (Firm war e version
1.1.5 or 2.2.1)
. Second and third generation iPod touch (Firm-
ware version 2.2.1 or IOS4/4.0.0)
. First generation iPod nano ( Firmware version
1.3.1)
. Second generation iPod nano (Firmware version
1.1.3)
. Third generation iPod nano (Fir mw are version
1.1.2PC or 1.1.3PC)
. Fourth generation iPod nano (Firmware version
1.0.2 or 1.0.4)
. Fifth generation iPod nano (Firmware version 1.0.1
or 1.0.2)
The iPod touch may not respond quickly to the system
in some cases.
Make sure that the iPod firmware is updated.
Operating tips:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
. iPod Shuffle and iPod mini are not supported.
. Some iPod operations may not be available with
this system.
AUX button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To operate the iPod use one of the following methods:
. Push the
button and then turn the dial to
select for the USB item. Once highlighted, push
the
dial.
. Push the
button repeatedly until “USB” is
highlighted and then push the
dial.
Audio main operation:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Interface:
The interface for iPod operation shown on the audio
system display is similar to the iPod interface. Use the
dial to play a track on the iPod.
The following items can be chosen from the menu list
screen.
. Playlists
. Artists
. Albums
. Tracks
. Genres
For further information about each item, see the iPod
owner’s manual.
The following operations are identical to the audio main
operation of Compact Disc (CD) operation. For details,
see “CD player operation” (P.4-40).
. List view
. Quick search
.
. MIX (Random play)
. RPT (Repeat track)
. Folder browsing
DISP button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
While a track with recorded music information tags
(ID3-tags) is being played, the title of the played track
is displayed. If the tags are not provided then a
notification message is displayed.
When the
button is pushed repeatedly, further
information about the track can be displayed along
with the track title as follows:
Track time ? Artist ? Album ? Folder name ? Track
time
Track details:
By pushing and holding the
button, the display
will show a detailed overview and after a few seconds
it will return to the main display. Push the
button
briefly to return to the main display immediately.
Radio Broadcast data system (RBDS)
GUID-8E4CE6FF-A2A8-41C7-ACC4-BC68BBF79935
The RBDS is a system through which encoded digital
information is transmitted by FM radio stations in
addition to the normal FM radio broadcasting. The
RBDS provides information services such as station
name, traffic information, and news.
NOTE:
In some countries or regions, some of these
services may not be available.
RBDS functions
GUID-5957F70A-94A5-4413-82F4-F656DFBAA01B
Programme Service (PS) function (station name
display function):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When an RBDS station is tuned in with seek or manual
tuning, the RBDS data is received and the PS name is
displayed.
Monitor, Heater and air conditioner, and audio system 4-43
4-44 Monitor, Heater and air conditioner, and audio system
FM-AM RADIO WITH COMPACT DISC (CD) PLAYER (Type F)
GUID-8F59B701-1CED-4805-A0EF-A54AEBCE075C
JVH0508X
1. Day/Night button
2. FM·AM band select button
3. RPT button
4. MIX button
5. Radio memory buttons
6. A-Z button
7. AUX button
8. CD eject button
9. CD button
10. Power/VOL dial
11. Rewind button
12. Fast Forward button
13. DISP button
14. SETUP button
15. Back button
16. TUNE/MENU/ENTER dial
17. Phone button
Audio main operation
GUID-C22EB9A0-95F3-4F43-9647-CAFCF131757E
The audio system operates when the ignition switch is
in the “ACC” or “ON” position.
Power/VOL dial:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Power ON/OFF:
To turn on the audio system, push the
dial.
. The system will turn on in the mode, which was
used immediately before the system was turned
off.
. If a CD is inserted or a USB and/or an AUX device
is connected when the system is turned off, and if
the system is turned on again with the devices
removed or disconnected, the radio will turn on.
To turn off the audio system, push the
dial.
Volume control:
To control the volume, turn the
dial.
Turn the
dial clockwise to make the sound louder.
Turn the
dial counterclockwise to make the sound
quieter.
SETUP button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To configure Audio, Clock, Bluetooth, Language or
Scroll direction settings, perform the following proce-
dure:
1. Push the
button.
2. Push the
dial.
3. Turn the
dial clockwise or counterclockwise.
The setting menu will be displayed in the following
order:
Audio Û Clock Û Bluetooth Û Language Û
Scroll Direction
After the desired levels have been set, either push the
button repeatedly, push the button, or wait
for several seconds without pushing any buttons to exit
the menu screen.
Audio adjustments:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the button to enter the setup menu screen
and then select “Audio”.
Each time the
dial is pushed, the mode will
change as follows:
BASS ? TREBLE ? BALANCE ? FADE ? AUX
VOL ? SPD VOL ? Audio (setup menu screen) ?
BASS
Turn the
dial clockwise or counterclockwise to
adjust the following items and push the
dial to
confirm.
Bass control:
Use this control to enhance or attenuate the bass
response sound.
Treble control:
Use this control to enhance or attenuate the treble.
Balance control:
Use this control to adjust the balance of the volume
between the left and right speakers.
Fader control:
Use this control to adjust the balance of the volume
between the front and rear speakers (if equipped).
AUX VOL (Auxiliary volume) control:
Use this control to adjust the volume output from the
auxiliary source.
SPD VOL (Speed volume) control:
This mode co ntrols the vol ume output from the
speakers automatically in relation to vehicle speed.
Adjusting the setting to “0” (zero) turns off the speed
volume feature.
Clock setting:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the dial n to enter the setup menu screen
and then select “Clock”.
Turn the
dial, the mode will change as follows:
Set Time Û ON/OFF Û Clock Format Û Set Time
Set Time:
Select “Set Time” then adjust the clock as follows:
The hour display will start flashing. Turn the
dial to
adjust the hour and push the
dial. The minute
display will start flashing. Turn the
dial to adjust
the minute and push the
dial to finish the clock
adjustment.
ON/OFF:
Set the clock display to on or off when the audio unit is
turned off. If set in the “ON” position, the clock will be
displayed when the audio unit is turned off either by
pushing the
dial or when the ignition switch is
placed in the “OFF” position.
Clock Format:
Switch the clock display between 24-hour and 12-
hour clock mode.
Language setting:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the button to enter the setup menu screen
and then select “Language”.
Select the appropriate language and push the
dial. Upon completion, the screen will automatically
adopt the language setting.
Monitor, Heater and air conditioner, and audio system 4-45
4-46 Monitor, Heater and air conditioner, and audio system
Scroll direction:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Set the scrolling behavior of the dial to scroll UP
or DOWN.
Day/Night button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the button to switch the display brightness
between the daytime and nighttime modes.
AUX button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the button to play a compatible device when
it is connected.
CD player operation
GUID-9E3BD738-DF2C-45E8-9081-0EF3477A579D
JVH0509X
The audio system operates when the ignition switch is
in the “ACC” or “ON” position.
Loading:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Insert a CD into the slot with the label side facing up.
The CD will be guided automatically into the slot and
will start playing. After loading the CD, the number of
tracks and the playtime will appear on the display.
CAUTION:
Do not force the CD into the slot. This could
damage the player.
NOTE:
. The CD player accepts normal audio CDs or
CDs containing MP3/WMA files.
. The audio unit will automatically detect if a
CD containing MP3/WMA files is inserted,
and [MP3CD] will be indicated.
. An error notification message will be dis-
played when an incompatible disc (e.g. DVD)
is inserted, or if the player cannot read the
CD. Eject the disc and insert another disc.
List view:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
While the track is being played, push either the
dial or the button to display the available tracks in
a listed view mode. Turn the
dial to select a track
from the list, or a track to start listening to, and then
push the
dial.
Quick search:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
In the list view mode, a quick search can be performed
to find a track from the list. Push the
button, turn
the
dial to the first alphabetic letter of the song
title and then push the
dial. When found, a list of
the available songs will be displayed. Select, and push
the
dial to play the preferred track.
CD button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while the audio
system is turned off and a CD is loaded, the audio
syste m will turn on and a CD will start playing
automatically. If the radio or AUX source mode is
already playing, it will automatically turn off and the CD
will start playing.
However, if the CD is not loaded, then a notification
message will be displayed and the audio unit will
remain in the radio or AUX source mode.
Fast Forward/Rewind buttons:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push and hold the / buttons to fast forward
or rewind through the track. When the button is
released, the track will play at normal playing speed.
Track up/down:
By pushing the
/ buttons once, the track will
skip forward to the next track or backward to the
beginning of the current track. Push the
/
buttons more than once to skip through the tracks.
Folder browsing:
If the recorded media contains folders with music files,
pushing the
/ button will play the tracks of
each folder in sequence.
To select a preferred folder:
1. Push the
dial or the button and a list of
tracks in the current folder is displayed.
2. Push the
button.
3. Turn the
dial to highlight the preferred folder.
4. Push the
dial to access the folder. Push the
dial again to start playing the first track or
turn the
dial, and push the dial to select
another track.
If the current selected folder contains sub folders, push
the
dial, and a new screen with a list of sub
folders will be displayed. Turn the
dial to highlight
the sub folder then push the
dial to access the
sub-folder. Select the root folder item when songs are
recorded additionally in the root folder.
To return to the previous folder screen, push the
button.
RPT button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the button and the current track will be
played continuously.
MIX button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the button and all the tracks will be played in
random order.
DISP button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
While a CD with recorded music information tags (CD-
text/ID3-text tags) is being played, the title of the
played track is displayed. If the title information is not
provided then “Track” is displayed.
When the
button is pushed repeatedly, further
information about the track can be displayed along
with the track title as follows:
CD:
Track time ? Artist ? Song ? Album ? Track time
CD with MP3/WMA:
Track time ? Artist ? Album ? Folder name ? Track
time
Track details:
By pushing and holding the
button will turn the
display will show a detailed overview and after a few
seconds will return to the main display. Push the
button to return to the main display immediately.
CD Eject button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while a CD is loaded,
the CD will be ejected.
When the
button is pushed twice, the CD will be
ejected further, so that the CD can be removed with
ease.
When the ignition switch is in the “OFF” or “LOCK”
position it is possible to eject the CD currently being
played. However the audio unit will not be activated.
If a CD is ejected by pushing the
button, and it is
not removed from the loading slot for some time, the
CD will automatically be reloaded to the slot to protect
the CD.
FM-AM radio operation
GUID-1D5EBA5D-8833-4228-9AA7-EAA84E0CC 287
The audio system operates when the ignition switch is
in the “ACC” or “ON” position.
FM·AM button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while the audio
system is turned off, the audio system will turn on and
the radio will turn on.
When the
button is pushed while another audio
source is playing, the other audio source will turn off
and the radio will turn on.
To change the radio band, push the
button until
the desired band appears.
FM 1 ? FM 2 ? FM T ? AM ? FM 1
During FM reception, when the
button is pushed
for longer than 1.5 seconds, stations are searched for
and the 6 stations of the FM T band are tuned in.
During the search, the notification message “AUTO-
STORE” appears in the display and the sound is muted
until the autostore operation is completed, upon which
preset channel 1 is automatically tuned in.
ENTER dial:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When adjusting the broadcasting station frequency
manually, turn th e
dial until the preferred
frequency is achieved.
The frequency changes in steps of 100 kHz on the FM
band and 9 kHz on the AM band.
Fast Forward/Rewind buttons:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When adjusting the broadcasting station frequency
automatically, push the
/ button. When the
system detects a broadcasting station, it will stop at
the station.
*
1
*
2
*
3
*
4
*
5
*
6
(Radio memory) buttons:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
During radio reception, pushing the radio memory
button for less than 2 seconds will select the stored
radio station.
The audio system can store up to 18 FM station
frequencies (six in each of FM 1, FM 2 and FM T) and 6
AM station frequencies.
To store the station frequency manually:
1. Tune to the desired broadcasting station fre-
quency by using the
/ button.
2. Push and hold a radio memory button
*
1
-
*
6
until a beep sounds. (The radio mutes when the
memory button is pushed.)
3. The channel indicator will display and the radio
mute disengages, indicating that the memory is
stored properly.
4. Perform steps 1 - 3 for all other memory buttons.
If the battery cable is disconnected, or if the audio fuse
blows, the radio memory will be erased. If this occurs,
Monitor, Heater and air conditioner, and audio system 4-47
4-48 Monitor, Heater and air conditioner, and audio system
reset the desired stations.
USB memory device operation
GUID-9D1BEADF-3B18-4472-816C-1DE672CA4456
JVH0518X
Audio main operation:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The USB outlet connector is located on the instrument
panel. Open the lid and connect a USB memory device
into the connector. The system will switch to the USB
memory device mode automatically.
If the system is turned off while the USB memory
device is playing, pushing the
dial will start the
USB memory device.
If the USB memory device cannot be played, one of the
following messages will be displayed.
. “USB memory device not supported”
. “No audio file detected”
CAUTION:
. Do not force the USB memory device into
the USB port. Inserting the USB memory
device tilted or upside down into the port
may damage the USB memory device and/or
the port. Make sure that the USB memory
device is connected correctly into the USB
port. (Some USB devices come with a
mark as a guide. Make sure that the mark is
facing the correct direction before inserting
the device.)
. Do not place objects near the USB memory
device to prevent the objects from leaning
on the USB memory device and the port.
Pressure from the objects may damage the
USB memory device and/or the port.
AUX button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To operate the USB memory device use one of the
following methods:
. Push the
button then turn the dial to
select the USB item. Once highlighted, push the
dial.
. Push the
button repeatedly until USB is
highlighted, and then push the
dial.
Audio main operation:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The following operations are identical to the audio main
operation of the Compact Disc (CD) operation. For
details, see “CD player operation” (P.4-46).
. List view
. Quick search
.
. MIX (Random play)
. RPT (Repeat track)
. Folder browsing
DISP button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
While a track with recorded music information tags
(ID3-tags) is being played, the title of the played track
is displayed. If the tags are not provided, a notification
message is displayed.
When the
button is pushed repeatedly, further
information about the track can be displayed along
with the track title as follows:
Track time ? Artist ? Album ? Folder name ? Track
time
Track details:
By pushing and holding the
button the display will
show a detailed overview and after a few seconds it
will return to the main display. Push the
button
briefly to return to the main display immediately.
iPod player operation
GUID-FD81A5CF-6AA5-4626-B051-70BF7A4038A1
Connecting iPod:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The USB outlet connector is located in the center
console. Open the USB outlet connector lid and
connect the iPod cable to the USB connector. The
battery of the iPod is charged while the device is
connected to the vehicle.
Depending on the version of the iPod, the display on
the iPod shows a NISSAN or Accessory Attached
screen when the connection is completed. When the
iPod is connected to the vehicle, the iPod music library
can only be operated by the vehicle audio controls.
* iPod and iPhone are trademarks of Apple Inc.,
registered in the U.S. and other countries.
CAUTION:
. Do not force the iPod cable into the USB
port. Inserting the iPod cable tilted or up-
side-down into the port may damage the
iPod cable and the port. Make sure that the
iPod cable is connected correctly into the
USB port. (Some iPod cables come with a
mark as a guide. Make sure that the
mark is facing the correct direction before
inserting the iPod cable.)
. Do not locate objects near the iPod cable to
prevent the objects from leaning on the iPod
cable and the port. Pressu re from the
objects may damage the iPod cable and
the port.
Compatibility:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The following models are supported:
. Third generation iPhone (Firmware version
IOS4/4.0)
. Fourt h genera tion iPhone (Firmware version
IOS4/4.0)
. Fifth generation iPod (Firmware version 1.3)
. First generation iPod Classic (Firmware version
1.1.1 or 1.1.2PC)
. Second generation iPod Classic (Firmware ver-
sion 2.0.1)
. First generation iPod touch (Firm war e version
1.1.5 or 2.2.1)
. Second and third generation iPod touch (Firm-
ware version 2.2.1 or IOS4/4.0.0)
. First generation iPod nano ( Firmware version
1.3.1)
. Second generation iPod nano (Firmware version
1.1.3)
. Third generation iPod nano (Fir mw are version
1.1.2PC or 1.1.3PC)
. Fourth generation iPod nano (Firmware version
1.0.2 or 1.0.4)
. Fifth generation iPod nano (Firmware version 1.0.1
or 1.0.2)
The iPod touch may not respond quickly to the system
in some cases.
Make sure that the iPod firmware is updated.
Operating tips:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
. iPod Shuffle and iPod mini are not supported.
. Some iPod operations may not be available with
this system.
AUX button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To operate the iPod use one of the following methods:
. Push the
button and then turn the dial
for the USB item. Once highlighted, push the
dial.
. Push the
button repeatedly until USB is
highlighted and then push the
dial.
Audio main operation:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Interface:
The interface for iPod operation shown on the audio
system display is similar to the iPod interface. Use the
dial to play a track on the iPod.
The following items can be chosen from the menu list
screen.
. Playlists
. Artists
. Albums
. Tracks
. Genres
For further information about each item, see the iPod
owner’s manual.
The following operations are identical to the audio main
operation of the Compact Disc (CD) operation. For
details, see “CD player operation” (P.4-46).
. List view
. Quick search
.
. MIX (Random play)
. RPT (Repeat track)
. Folder browsing
DISP button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
While a track with recorded music information tags
(ID3-tags) is being played, the title of the played track
is displayed. If the tags are not provided then a
notification message is displayed.
When the
button is pushed repeatedly, further
information about the track can be displayed along
with the track title as follows:
Track time ? Artist ? Album ? Folder name ? Track
time
Track details:
By pushing and holding the
button the display will
show a detailed overview and after a few seconds it
will return to the main display. Push the
button
briefly to return to the main display immediately.
Bluetooth
®
audio player operation
GUID-32CAE781-FBA5-47D3-9B53-71EB8C92DC09
Regulatory information:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Bluetooth
®
is a trademark owned
by Bluetooth SIG, Inc., and
licensed to Daewoo IS Corp.
CE statement:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Hereby Daewoo IS Corp. declares that this system is
in compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC.
NSY0105
Monitor, Heater and air conditioner, and audio system 4-49
4-50 Monitor, Heater and air conditioner, and audio system
NOTE:
The audio system only supports Bluetooth
®
devices with AVRCP (Audio Video Remote Con-
trol Profile) version 1.3, 1.0, or earlier.
Bluetooth
®
audio player setting:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To set up the Bluetooth
®
system with your preferred
device, push the
button and select Bluetooth
®
,
and then push the
dial or alternatively, push the
button. The following items are available:
. Pair Device
Bluetooth
®
devices can be paired with the system.
A maximum of 5 devices can be registered.
. Select Device
Paired Bluetooth
®
devices are listed and can be
selected for connection.
. Delete Device
A registered Bluetooth
®
device can be deleted.
. On/Off
If this setting is turned off, the connection between
the Bluetooth
®
devices and the in-vehicle Blue-
tooth
®
module will be cancelled.
NOS2761
Pair Device:
1. Push the
button. Select the Bluetooth
®
key
by turning the
dial, and then push the
dial.
You can register up to 5 different Bluetooth
®
audio/cellular phone devices. However, you can
only use one device at a time. If you have 5
different Bluetooth
®
devices, a newly registered
device can only replace one of the already
registered 5 existing paired devices. Use the
“Delete Device” key to delete one of the existing
paired devices.
2. Select the “Pair Device” key.
The pairing procedure depends on the connected
device:
.
Cellular phone:
The message Ready to Pair Pin:1234 will be
displayed.
.
Audio device without PIN code:
The Bluetooth
®
connection will be automati-
cally connected without any further input.
.
Audio device with PIN code:
A new screen will appear. Assign the 4 digit
PIN code by turning the
dial to each digit
of the code and pushing the
dial to
confirm each digit. After the PIN code is input,
select “Validate” and push the
dial. The
Bluetooth
®
connection will be made.
The 4-digit PIN code is provided with the audio
device, see the owner’s manual of the audio
device.
3. On Bluetooth
®
audio/cellular phone devices:
a. Check that Bluetooth
®
is turned on, on your
device.
b. Switch to the search mode for Bluetooth
®
devices. If the search mode finds a device it
will be shown on the device display. Select My
Car.
c. Enter the number code shown on the relevant
device with the device’s own keypad, and push
the confirmation key on the device itself. Refer
to the relevant Bluet ooth
®
device owner’s
manual for further details.
When the device is successfully paired a notification
message will be displayed, and then the audio system
display will return to the current audio source display.
During connection the following status icons will be
displayed (top left of the display): Signal strength
(
), Battery status* ( ) and Bluetooth
®
“ON”
(
).
*: If the low battery message comes on, the Bluetooth
®
device must be recharged soon.
The pairing proc edure and operation may vary
according to device type and compatibility. See the
owner’s manual of the Bluetooth
®
device for further
details.
Select Device:
The paired device list shows which Bluetooth
®
audio
or ce llu lar phone devices have been paired or
registered with the Bluetooth
®
audio system. If the list
contains devices, select the appropriate device to
connect to the Bluetooth
®
audio system.
The following symbols indicate the capability of the
registered device:
.
: cellular phone integration
.
: Audio streaming (A2DP- Advanced Audio
Distribution Profile)
Delete Device:
A registered device can be removed from the Blue-
tooth
®
audio system. Select a registered device then
push the
button to confirm deletion.
On/Off:
If Bluetooth
®
has been switched off, a notification
message On/Off appears when you select Bluetooth
®
from the setup menu screen, or push the button.
To turn the Bluetooth
®
signal on, push the dial
and a follow up screen will appear. Select “On” and
push the
dial to display the Bluetooth
®
settings
menu screen.
Bluetooth
®
audio streaming main operation:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
NOS2762
Turn the ignition switch to the “ACC” or “ON” position.
If the audio system is turned off while the Bluetooth
®
audio is playing, pushing the dial will start
Bluetooth
®
audio streaming.
AUX button:
To operate Bluetooth
®
audio streaming use one of the
following methods:
. Push the
button, then turn the dial to
highlight BT Audio, and push the
dial.
. Push
repeatedly until BT Audio is highlighted,
then push the
dial.
The type of display,
*
A
or
*
B
, shown on the audio
system can vary depending on the Bluetooth
®
version
of the device.
Fast Forward/Rewind buttons:
Fast Forward, Fast Reverse:
When the
/ button is pushed continuously,
the track will be played at high speed. When the button
is released, the track will be played at normal playing
speed.
Track up/down:
By pushing the
/ button once, the track will
be skipped forward to the next track or backward to
the beginning of the current played track. Push the
/ button more than once to skip through the
tracks.
DISP button:
If the song contains music information tags (ID3-tags),
the title of the played song will be displayed. If tags are
not provided, the display will not show any messages.
When the
button is pushed repeatedly, further
information about the song can be displayed along
with the song title.
By pushing and holding the
button the display will
show a detailed overview which after a few seconds
will return to the main display. Push the
button
briefly to return to the main display immediately.
Radio Broadcast data system (RBDS)
GUID-6A4AA979-71C4-4 7F1-AF38-B21D4FDD2FF2
The RBDS is a system through which encoded digital
information is transmitted by FM radio stations in
addition to the normal FM radio broadcasting. The
RBDS provides information services such as station
name, traffic information, and news.
NOTE:
In some countries or regions, some of these
services may not be available.
Alternative Frequency (AF) mode:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The AF mode operates in the FM (radio) mode.
. The AF mode operates both in the FM (radio) and
CD mode (if FM was previously selected in the
radio mode).
. The AF function compares signal strengths and
selects the station with the optimum reception
conditions for the currently tuned-in station.
RBDS functions
GUID-4076D2F6-957E-4D0C-93F3-6A860E21 7BF1
Programme Service (PS) function (station name
display function):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When an RBDS station is tuned in with seek or manual
tuning, the RBDS data is received and the PS name is
displayed.
Monitor, Heater and air conditioner, and audio system 4-51
4-52 Monitor, Heater and air conditioner, and audio system
LW-MW-FM RADIO WITH COMPACT DISC (CD) PLAYER
GUID-6A9CD14F-B6E3-4056-B506-430C33ADFEBB
SAA2379
1. MUTE button
2. POWER ON/OFF button
3. Sound preference button
4. FM band select button
5. AM band select button
6. Radio memory buttons
7. CD button
8. AUX button
9. TA (Traffic Announcement) button
10. MENU button
11. CD EJECT button
12. SEEK/TRACK button
13. MIX (Mix play) button
14. RPT (Repeat) button
15. VOLUME control/MENU select dial
16. ENTER button
17. AUX IN (auxiliary input) jack
18. NEWS button
19. TUNE/SEARCH button
Anti-theft system (if equipped)
GUID-0B1806B3-B3F3-454E-96F7-F01E3B55322A
This unit can only be activated when the ignition switch
for NATS is in the “ACC” or “ON” position.
Each radio is uniquely matched to the vehicle’s
immobilizer and therefore cannot be transferred to
any other vehicle.
Audio main operation
GUID-0F37ACCE-50E0-4C87-94A7-2BA1849C6F2D
The audio system operates when the ignition switch is
in the “ACC” or “ON” position.
POWER ON/OFF button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To turn on the audio system, push the POWER ON/
OFF button.
. The system will turn on in the mode, (radio or CD)
which was used immediately before the system
was last turned off.
. If there is no CD loaded, the radio will be turned
on.
To turn off the audio system, push the POWER ON/
OFF button.
Volume control:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To control the volume, turn the VOLUME control dial.
Turn the VOLUME control dial clockwise to increase
the audio volume.
Turn the VOLUME control dial counterclockwise to
decrease the audio volume.
Sound preference button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To enter the audio mode (radio or CD), push the
button.
To change the audio settings (BASS, TREBLE, FADE,
BALANCE, EQ), push the
button or ENTER
button to select the mode.
BASS ? TREBLE ? BALANCE ? FADE ? EQ ?
BASS
To adjust each audio setting, turn the MENU/VOL
control dial clockwise or counterclockwise.
BASS: (−) to decrease / (+) to increase
TREB(LE): (−) to decrease / (+) to increase
BAL(ANCE): (R) to adjust to the right / (L) to adjust to
the left
FADE(R): (F) to adjust to the front / (R) to adjust to the
rear
EQ (Equalizer): Use this control to change the preset
sound mode for CD play.
Turn the MENU/VOL dial clockwise or counterclock-
wise. The mode will change as follows:
OFF Û ENHANCE Û OFF
If the audio settings mode is unchanged for approxi-
mately 5 seconds, the audio sett ings mode will
automatically return to the normal mode.
Clock display:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Turning on/off the clock display
To turn on or off the clock display, perform the
following operations.
1. Push the MENU button while the audio system is
on.
2. Turn the VOLUME control dial until "CLOCK"
appears on the display.
3. Push the ENTER bu tton. ("CLOCK OFF" or
"CLOCK ON" is displayed.)
4. To turn on the clock display, turn the VOLUME
control dial till "CLOCK ON" is displayed. To turn
off the clock display, turn the VOLUME control dial
till "CLOCK OFF" is displayed, and push ENTER.
Clock adjustment
To adjust the time of the clock, perform the following
operations.
1. Push the ENTER button while "CLOCK ON" is
displayed.
2. The hour display will flash.
3. Turn the VOLUME control dial to adjust the hour.
4. Push the ENTER button. The minute display will
flash.
5. Turn the VOLUME control dial to adjust the
minute.
6. Push the ENTER button to complete the clock
adjustment.
Mute button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the MUTE button to mute the audio system.
MUTE appears on the display. To unmute, use any one
of the following options:
. Push the MUTE button again.
. Turn the VOLUME control dial.
. Push the CD, FM or AM button.
. Push the AUX button.
AUX button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The AUX IN jack is located on the audio unit. The AUX
IN audio input jack accepts any standard analog audio
input such as from a portable cassette tape player, CD
player, MP3 player or laptop computer.
Push the AUX button to play a compatible device when
it is plugged into the AUX IN jack.
NISSAN strongly recommends using a stereo mini
plug cable when connecting your music device to the
audio system. Music may not play properly when a
Monitor, Heater and air conditioner, and audio system 4-53
4-54 Monitor, Heater and air conditioner, and audio system
monaural cable is used.
CD player operation
GUID-108C6D9A-02FF-45FA-9BBC-73B6407DEA62
SAA2380
The audio system operates when the ignition switch is
in the “ACC” or “ON” position.
Loading:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Insert a CD into the slot with the label side facing up.
The CD will be guided automatically into the slot and
will start playing. If the radio is already playing, it will
automatically turn off, and the CD will start playing.
CAUTION:
Do not force the CD into the slot. This could
damage the player.
After loading the CD, the number of tracks and the
playtime will appear on the display.
CD button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while the audio
system is off and a CD is loaded, the audio system will
turn on and a CD will start playing automatically. If the
radio is already playing, it will automatically turn off and
the CD will start playing.
/ FF (Fast Forward), REW (Rewind)
button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push and hold the FF or REW button while a CD is
being played to fast-forward or rewind though the
track. When the button is released, the CD will return
to the normal play speed.
/ TRACK UP/ DOWN button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the track up button while a CD is being played to
skip forward to the next track. The CD will advance the
number of times the button is pushed. When the last
track of the CD is skipped, the first track will be played.
Push the track down button while a CD is being played
to start the present track again from the beginning.
Push the track down button several times to skip back
to the previous track. The CD will skip tracks backward
the number of times the button is pushed. When the
first track of the CD is skipped, the last track will be
played.
Repeat button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the button repeatedly to change the play
mode as follows:
RPT (REPEAT) TRACK ? RPT (REPEAT) ALL ? RPT
(REPEAT) TRACK
RPT TRACK:
The selected track will be played repeatedly.
RPT ALL:
All the tracks on the CD will be played in sequential
order.
MIX button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the button repeatedly to change the play
mode as follows:
MIX DISC ? RPT (REPEAT) ALL ? MIX DISC
MIX DISC:
All the tracks on the CD will be played in a random
order.
RPT ALL:
All the tracks on the CD will be played in sequential
order.
CD EJECT button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while a CD is loaded,
the CD will be ejected.
When the
button is pushed twice, the CD will be
ejected further, and the CD can be removed easily.
If a CD is ejected by pushing the
button, and it is
not taken out from the loading slot, the CD will
automatically be reloaded to the slot to protect the CD.
LW-MW-FM radio operation
GUID-26B351F1-BF06-4FF6-8B60-4538B0FEB6F4
SAA2380
The audio system operates when the ignition switch is
in the “ACC” or “ON” position.
FM-AM button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the / button is pushed while the audio
system is off, the audio system and the radio will turn
on. When the
/ button is pushed while the CD
player is already operating, it will automatically turn off
and the radio will turn on.
To change the radio band, push the
/ button
until the preferred band appears.
. For FM
FM 1 ? FM 2 ? FM T
. For AM
MW ? LW ? MW
During FM reception, when the
button is pushed
for longer than 1.5 seconds, stations are searched for
and the 6 stations of the FM T band. The sound is
muted until the auto store operation is completed,
upon which preset channel 1 is automatically tuned in.
TUNE button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When adjusting the broadcasting station frequency
manually, push the
or button until the
preferred frequency is obtained.
The frequency changes in steps of 100 kHz on the FM
band, 9 kHz on the MW band, and 3 kHz on the LW
band.
SEEK button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When adjusting the broadcasting station frequency
automatically, push the
or button. When the
system detects a broadcasting station, it will stop at
that station.
*
1
*
2
*
3
*
4
*
5
*
6
Radio memory buttons:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The audio system can store up to 18 FM station
frequencies (six in each of FM 1, FM 2 and FM T), 6
MW and 6 LW station frequencies.
To store the station frequency manually:
1. Tune to the preferred broadcasting station fre-
quency by using the
or
button.
2. Push and hold a radio memory button
*
1
-
*
6
until a beep sounds. (The radio mutes when the
memory button is pushed.)
3. The channel indicator will be displayed and the
radio mute will be cancelled, indicating that the
memory is stored properly.
4. Perform steps 1 - 3 for all other memory buttons.
If the battery cable is disconnected, or if the audio fuse
blows, the radio memory will be erased. If this occurs,
reset the desired stations.
Radio data system (RDS)
GUID-237F0783-B830-4397-9033-EF65999545BA
Alternative Frequency (AF) :
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
. The AF function operates in the FM (radio) and CD
modes.
. When the AF mode is set to “ON” in the user
setup menu mode, the AF indicator illuminates.
For activation or deactivation, use the MENU button.
(Details are explained later in this section.)
. Automatic switching function
This function compares the strengths of the
signals of all the stations on the AF list and
selects the station with the optimum reception
conditions.
. Program Information (PI) search
Program Information (PI) search begins automati-
cally if no suitable station is found with the above
automatic switching function . The PI search
function checks each RDS station with the same
PI code. During this time the sound is muted and
“PI SEARCH” is displayed. The PI search opera-
tion stops when a suitable station is found. If no
station is found once all the frequencies have been
searc hed, the radio returns to the previou s
frequency.
. Enhanced Other Network (EON) data update
(This function also operates when the AF
mode is off.)
When EON data is being received, this enables
automatic retuning of other preset stations on the
same network. Also, network linked services can
be used. The EON indicator turns on during
reception of RDS EON stations in the FM mode.
RDS functions:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
. Programme Service (PS) function (station
name display function)
When an RDS station is tuned in with seek or
manual tuning, RDS data is received and the
Program Service (PS) name is displayed.
. Emergency broadcast interrupt function
(ALARM INTERRUPTION — EBU SPEC FOR
INFO)
When the radio receives PTY code 31 (an
emergency broadcast code), the sound is inter-
rupted, the emergency broadcast is heard, and
“PTY31 ALARM” is displayed. The volume level at
this time is the same as that for traffic announce-
ments. Once the emergency broadcast is finished,
the unit immediately returns to the previous
source.
. REG (Regional) mode
Some local radio stations are linked together
Monitor, Heater and air conditioner, and audio system 4-55
4-56 Monitor, Heater and air conditioner, and audio system
according to their region because they only offer
limited coverage due to their limited number of
transmitters. If the signal from one station be-
comes weak while you are driving around, RDS
mode will switch to another local station in the
region with a stronger signal.
When the REG mode is activated in the FM band
and the radio receiver is tuned to a local radio
station, it will keep receiving this radio station
without switching to another local station. For
activation or deactivation, use the MENU button.
(Details are explained later in this section.)
Traffic Announcement (TA):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
. The TA function operates in the FM and CD
modes.
. The TA mode is turned on or off when the TA
button is pushed for less than 2 seconds.
. The TA mode operates regardless of whether the
AF mode is on or off.
. “TA ON” is displayed when the TA mode is turned
on, and the TA indicator turns on. “TA OFF” is
displayed when the TA mode is turned off, and the
TA indicator turns off.
The following function operates when the TA mode is
on:
. Traffic announcement interrupt function
When a traffic announcement is received, the
announcement is tuned in and the volume
increases to the set level.
Once the traffic announcement is finished, the unit
returns to the source which was set before the
traffic a nnouncement started, and the volume
returns to the previous level. For EON stations,
the radio is interrupted by another EON station
with traffic announcements.
The traff ic announcement interrupt mode is
cancelled if the TA button is pushed during a
traffic announcement. The TA mode returns to the
standby mode and the audio unit returns to the
previous source.
News mode:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the NEWS button is pushed for longer than 2
seconds in the FM mode , the news function is
activated. “NEWS” is displayed for 3 seconds and
the NEWS indicator appears on the display.
When the news function is activated, the radio
receives a news code from the FM broadcasting news
station and the play mode will be interrupted. Once the
news broadcast is finished, the unit returns to the
previous mode.
In some countries or regions, th i s service is not
available or the signal is too weak to be received.
1. News standby mode
.
The news standby mode can be activated in
the FM or CD mode.
.
A news interruption will be announced and
“NEWS” will be displayed when the radio
detects the news code from the tuned station
or EON stations. The display will then change
to the PS name of the interrupting station.
.
When pushing the NEWS button for longer
than 2 seconds, the news standby mode is
turned off and the indicator disappears from
the display.
2. News interruption mode
.
When the NEWS button is pushed during the
news interruption mode, the radio returns to the
previous source. However, the news standby
mode is maintained.
.
When the
button is pushed during the
news interruption mode, the radio changes to
the CD mode. However, the news standby
mode is maintained.
If the radio band is changed to the MW or LW,
the news standby mode will be turned off.
MENU button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To configure Alternative Frequency, Regional an d
Language settings, perform the following procedure:
1. Push and hold the MENU button for at least 1.5
seconds.
2. Turn the VOLUME control dial clockwise or
counterclockwise. The display message wil l
change as follows:
AF Û REG Û LANGUAGE Û AF
. To activate or deactivate the AF and REG mode,
briefly push the ENTER button when AF or REG
appears on the display and turn the VOLUME
control dial clock wise or counterclockwise to
switch between the off or on position. After
selection, push the ENTER button to confirm the
settings.
— When the AF mode is enabled, the audio unit
will automatically re-tune to a stronger fre-
quency if the radio signal becomes weak.
— When the REG mode is enabled, the audio unit
will maintain and maintain the station which is
broadcasting local (regional) programmes.
. To change the display language, briefly push the
ENTER button when LANGUAGE appears on the
display then turn the MENU/VOL dial clockwise or
counterclockwise to select the appropriate lan-
guage setting.
ENGLISH Û DUTCH Û FRENCH Û SPANISH
Û GERMAN Û ITALIAN Û PORTUGUESE Û
ENGLISH
After selecting the preferred language, push the
ENTER button to exit the menu.
To configure the SPEED volume and BEEP settings,
perform the following procedure:
1. Push the MENU button.
2. Turn the Volume control dial clockwise or counter-
clockwise. The display message will change as
follows:
SPEED VOL Û CLOCK Û BEEP
. When SPEED VOL appears on the display, briefly
push the ENTER button then turn the VOLUME
control dial clock wise or counterclockwise to
adjust the level of the volume.
Adjusting the setting to 0 (zero) turns off the
speed volume feature. Increa sing th e speed
volume setting results in the audi o volume
increasing more rapidly with vehicle speed. Push
the ENTER button again to save the setting.
. When BEEP appears on the display, briefly push
the ENTER button and then turn the VOLUME
control dial clock wise or counterclockwise to
switch the beep sound on or off. Push the ENTER
button again to save the setting.
After the preferred levels have been set, push the
MENU button to exit the menu or wait at least for 10
seconds without pressing any buttons.
For clock adjustments, see “Audio main operation”
(P.4-53).
LW-MW-FM RADIO WITH COMPACT DISC (CD) CHANGER
GUID-09378FC5-F692- 4F38-920E-B917215D1033
JVH0044X
1. CD LOAD button
2. POWER ON/OFF button
3. PHONE SEND button
4. TA (Traffic Announcement)/NEWS button
5. Radio band select button
6. Radio memory/CD select buttons
7. CD button
8. AUX button
9. Sound preference button
10. MENU button
11. CD EJECT button
12. SEEK/TRACK button
13. PHONE BOOK button
14. PHONE END/BACK button
15. VOLUME control/MENU select knob
16. ENTER button
Monitor, Heater and air conditioner, and audio system 4-57
4-58 Monitor, Heater and air conditioner, and audio system
17. AUX IN (auxiliary input) jack
18. RPT (Repeat)/MIX (Mix play) button
19. TUNE/SEARCH button
Anti-theft system (if equipped)
GUID-8F9676CC-8B9A-4A00-AA79-2C6C23138E02
This unit can only be activated when the ignition switch
for NATS is in the “ACC” or “ON” position.
Each radio is uniquely matched to the vehicle’s
immobilizer and therefore cannot be transferred to
any other vehicle.
Audio main operation
GUID-1FB203B0-2837-457B-A593-36D3628B1DB7
The audio system operates when the ignition switch is
in the “ACC” or “ON” position.
POWER ON/OFF button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To turn on the audio system, push the POWER ON/
OFF button.
. The system will turn on in the mode, (radio or CD)
which was used immediately before the system
was last turned off.
. If there is no CD loaded, the radio will be turned
on.
To turn off the audio system, push the POWER ON/
OFF button.
Volume control:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To control the volume, turn the VOLUME control dial.
Turn the VOLUME control dial clockwise to increase
the audio volume.
Turn the VOLUME control dial counterclockwise to
decrease the audio volume.
Sound preference button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To enter the audio mode (radio or CD), push the
button. When no CD is loaded, the audio system will
automatically switch to the radio mode.
To change the audio settin gs (BASS, TREBLE,
FADER, BALANCE, EQ), push the
button or
ENTER button to select the mode.
BASS ? TREBLE ? BALANCE ? FADER ? EQ ?
BASS
To adjust each audio setting, turn the MENU/VOL
control dial clockwise or counterclockwise.
BASS: (−) to decrease / (+) to increase
TREB(LE): (−) to decrease / (+) to increase
BAL(ANCE): (R) to adjust to the right / (L) to adjust to
the left
FADE(R): (F) to adjust to the front / (R) to adjust to the
rear
EQ (Equalizer): Use this control to change the preset
sound mode for CD play.
Turn the MENU/VOL dial clockwise or counterclock-
wise. The mode will change as follows:
OFF Û ENHANCE Û OFF
If the audio settings mode is unchanged for approxi-
mately 8 seconds, the audio sett ings mode will
automatically return to the normal mode.
Clock display:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Turning on/off the clock display
To turn on or off the clock display, perform the
following operations.
1. Push the MENU button while the audio system is
on. ("PHONE SETUP" is displayed.)
2. Turn the VOLUME control knob until "CLOCK"
appears on the display.
3. Push the ENTER bu tton. ("CLOCK OFF" or
"CLOCK ON" is displayed.)
4. To turn on the clock display, turn the VOLUME
control knob till "CLOCK ON" is displayed. To turn
off the clock display, turn the VOLUME control
knob till "CLOCK OFF" is displayed, and push
ENTER.
Clock adjustment
To adjust the time of the clock, perform the following
operations.
1. Push the ENTER button while "CLOCK ON" is
displayed.
2. The hour display will flash.
3. Turn the VOLUME control knob to adjust the hour.
4. Push the ENTER button. The minute display will
flash.
5. Turn the VOLUME control knob to adjust the
minute.
6. Push the ENTER button to complete the clock
adjustment.
AUX button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The AUX IN jack is located on the audio unit. The AUX
IN audio input jack accepts any standard analog audio
input such as from a portable cassette tape player, CD
player, MP3 player or laptop computer.
Push the AUX button to play a compatible device when
it is plugged into the AUX IN jack.
NISSAN strongly recommends using a stereo mini
plug cable when connecting your music device to the
audio system. Music may not play properly when a
monaural cable is used.
CD changer operation
GUID-5C006A55-5D29-458D-B6B9-80DFFF96E98A
JVH0045X
The audio system operates when the ignition switch is
in the “ACC” or “ON” position.
CD LOAD button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed, the CD loading slot
will open and the loading position will be displayed.
Insert the CD into the slot with the label side facing up.
The CD will be guided automatically into the slot and
will start playing. If the radio is already playing, it will
automatically turn off and the CD will start playing.
CAUTION:
. Do not force the compact disc into the slot.
This could damage the player.
. Do not use 8 cm (3.1 in) discs.
After loading the CD, the slot number and CD track will
appear on the display.
To load a CD in the CD changer:
1. Push the
button for less than 1.5 seconds.
2. Select the loading slot by pushing the CD select
button. If no slot is selected, the CD changer will
automatically select an available slot.
3. Insert the CD into the slot.
To load 6 CDs in the CD changer:
1. Push the
button for more than 1.5 seconds.
2. Insert a CD into the slot.
3. When the next loading slot number illuminates on
the display, insert the next CD into the slot.
To load 6 CDs in the CD changer:
1. Push the
button for more than 1.5 seconds.
2. Insert the CD into the slot.
3. When the next loading slot number illuminates on
the display, insert the next CD into the slot.
The slot number indicator appears on the display when
the CDs are loaded in the CD changer and the audio
system is turned on.
CD PLAY button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while the audio
system is off and CDs are loaded, the audio system will
turn on and the CD will start to play automatically. If the
radio is already operating, it will automatically turn off
and the CD will start playing.
FF (Fast Forward), REW (Rewind)
button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the (fast forward) or (rewind) button
while a CD is being played to fast-forward or rewind
through the track. When the button is released, the CD
will return to normal play speed.
TRACK UP/ DOWN button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the button while a CD is being played to
skip forward to the next track. The CD will skip tracks
forward the number of times the button is pushed.
When the last track of the CD is skipped, the first track
will be played.
Push the
button while a CD is being played to
start the present track again from the beginning. Push
the
button several times to skip back to the
previous track. The CD will skip tracks backward the
number of times the button is pushed. When the first
track of the CD is skipped, the last track will be played.
*
1
*
2
*
3
*
4
*
5
*
6
CD select buttons:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To change to another CD loaded in the CD changer,
push the corresponding CD select button. When a CD
is selected, the selected CD will be automatically
played from the first track.
RPT (Repeat)·MIX button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the button repeatedly to change the play
mode as follows:
RPT (REPEAT) TRACK ? RPT (REPEAT) DISC ?
MIX DISC ? MIX ALL ? RPT (REPEAT) ALL ? RPT
(REPEAT) TRACK
RPT TRACK:
The CD changer plays the current track con-
tinuously.
RPT DISC:
The CD changer repeats the disc currently being
playing.
MIX ALL:
Monitor, Heater and air conditioner, and audio system 4-59
4-60 Monitor, Heater and air conditioner, and audio system
All the tracks on all of the CDs will be played in a
random order.
MIX DISC:
The CD changer plays all the tracks from one
disc once in a random order.
RPT ALL:
All the tracks of all the CDs will be played
continuously in sequential order.
CD EJECT button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed for less than 1.5
seconds while CDs are loaded, the previously played
CD will be ejected.
When the
button is pushed for less than 1.5
seconds while a CD is being played, the CD being
played will be ejected, and the next CD will be played.
When the
button is pushed for more than 1.5
seconds while CDs are loaded, all of the CDs in the
CD changer will be ejected.
If a CD is ejected by pushing the
button, and it is
not taken out from the loading slot within 15 seconds,
the CD will automatically be reloaded into the slot to
protect the CD.
If an error message appears on the display, push the
button.
When the ignition switch is in the “OFF” or “LOCK”
position, it is possible to eject all the CDs. However,
the audio unit will not be activated.
LW-MW-FM radio operation
GUID-17A9BA34-7D79-4060-AC48-A430CAD55F06
JVH0045X
The audio system operates when the ignition switch is
in the “ACC” or “ON” position.
FM-AM button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the button is pushed while the audio
system is off, the audio system and the radio will turn
on. When the
button is pushed while the CD
player is already operating, it will automatically turn off
and the radio will turn on.
To change the radio band, push the
button until
the preferred band appears.
FM 1 ? FM 2 ? FM T ? MW ? LW
During FM reception, when the
button is pushed
for longer than 1.5 seconds, stations are searched for
and the 6 stations of the FM T band. The sound is
muted until the auto store operation is completed,
upon which preset channel 1 is automatically tuned in.
TUNE button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When adjusting the broadcasting station frequency
manually, push the
button until the preferred
frequency is obtained.
The frequency changes in steps of 100 kHz on the FM
band, 9 kHz on the MW band, and 3 kHz on the LW
band.
SEEK button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When adjusting the broadcasting station frequency
automatically, push the
button. When the
system detects a broadcasting station, it will stop at
that station.
*
1
*
2
*
3
*
4
*
5
*
6
Radio memory buttons:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The audio system can store up to 18 FM station
frequencies (six in each of FM 1, FM 2 and FM T), 6
MW and 6 LW station frequencies.
To store the station frequency manually:
1. Tune to the preferred broadcasting station fre-
quency by using the
or
button.
2. Push and hold a radio memory button
*
1
-
*
6
until a beep sounds. (The radio mutes when the
memory button is pushed.)
3. The channel indicator will be displayed and the
radio mute will be cancelled, indicating that the
memory is stored properly.
4. Perform steps 1 - 3 for all other memory buttons.
If the battery cable is disconnected, or if the audio fuse
blows, the radio memory will be erased. If this occurs,
reset the desired stations.
Radio data system (RDS)
GUID-67777254-BE04-4DA5-9C3C-300C65EE536A
Alternative Frequency (AF) :
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
. The AF function operates in the FM (radio) and CD
modes.
. When the AF mode is set to “ON” in the user
setup menu mode, the AF indicator illuminates.
For activation or deactivation, use the MENU button.
(Details are explained later in this section.)
. Automatic switching function
This function compares the strengths of the
signals of all the stations on the AF list and
selects the station with the optimum reception
conditions.
. Program Information (PI) search
Program Information (PI) search begins automati-
cally if no suitable station is found with the above
automatic switching function . The PI search
function checks each RDS station with the same
PI code. During this time the sound is muted and
“PI SEARCH” is displayed. The PI search opera-
tion stops when a suitable station is found. If no
station is found once all the frequencies have been
searc hed, the radio returns to the previou s
frequency.
. Enhanced Other Network (EON) data update
(This function also operates when the AF
mode is off.)
When EON data is being received, this enables
automatic retuning of other preset stations on the
same network. Also, network linked services can
be used. The EON indicator turns on during the
reception of RDS EON stations in the FM mode.
RDS functions:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
. Programme Service (PS) function (station
name display function)
When an RDS station is tuned in with seek or
manual tuning, the RDS data is received and the
Program Service (PS) name is displayed.
. Emergency broadcast interrupt function
(ALARM INTERRUPTION — EBU SPEC FOR
INFO)
When the radio receives PTY code 31 (an
emergency broadcast code), the sound is inter-
rupted, the emergency broadcast is heard, and
“PTY31 ALARM” is displayed. The volume level at
this time is the same as that for traffic announce-
ments. Once the emergency broadcast is finished,
the unit immediately returns to the previous
source.
. REG (Regional) mode
Some local radio stations are linked together
according to their region because they only offer
limited coverage due to their limited number of
transmitters. If the signal from one station be-
comes weak while you are driving around, RDS
mode will switch to another local station in the
region with a stronger signal.
When the REG mode is activated in the FM band
and the radio receiver is tuned to a local radio
station, it will keep receiving this radio station
without switching to another local station. For
activation or deactivation, use the MENU button.
(Details are explained later in this section.).
Traffic Announcement (TA):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
. The TA function operates in the FM and CD
modes.
. The TA mode is turned on or off when the TA/
NEWS button is pushed for less than 2 seconds.
. The TA mode operates regardless of whether the
AF mode is on or off.
. “TA ON” is displayed when the TA mode is turned
on, and the TA indicator turns on. “TA OFF” is
displayed when the TA mode is turned off, and the
TA indicator turns off.
The following function operates when the TA mode is
on:
. Traffic announcement interrupt function
When a traffic announcement is received, the
announcement is tuned in and the volume
increases to the set level.
Once the traffic announcement is finished, the unit
returns to the source which was set before the
traffic a nnouncement started, and the volume
returns to the previous level. For EON stations,
the radio is interrupted by another EON station
with traffic announcements.
The traff ic announcement interrupt mode is
cancelled if th e TA/NEWS button is pushed
during a traffic an nouncement. The TA mode
returns to the standby mode and the audio unit
returns to the previous source.
News mode:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the NEWS button or the TA/NEWS button is
pushed for longer than 2 seconds in the FM mode, the
news function is activated. “NEWS” is displayed for 3
seconds and the NEWS indicator appears on the
display.
When the news function is activated, the radio
Monitor, Heater and air conditioner, and audio system 4-61
4-62 Monitor, Heater and air conditioner, and audio system
receives a news code from the FM broadcasting news
station and the play mode will be interrupted. Once the
news broadcast is finished, the unit returns to the
previous mode.
In some countries or regions, th i s service is not
available or the signal is too weak to be received.
1. News standby mode
.
The news standby mode can be activated in
the FM or CD mode.
.
A news interruption will be announced and
“NEWS” will be displayed when the radio
detects the news code from the tuned station
or EON stations. The display will then change
to the PS name of the interrupting station.
.
When pushing the TA/NEWS button for longer
than 2 seconds, the news standby mode is
turned off and the indicator disappears from
the display.
2. News interruption mode
.
When the TA/NEWS button is pushed during
the news interruption mode, the radio returns to
the previous source. Howe ver, the news
standby mode is maintained.
.
When the
button is pushed during the
news interruption mode, the radio changes to
the CD mode. However, the news standby
mode is maintained.
If the radio band is changed to the MW or LW,
the news standby mode will be turned off.
MENU button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To configure Alternative Frequency, Regional an d
Language settings, perform the following procedure:
1. Push and hold the MENU button for at least 1.5
seconds.
2. Turn the MENU/VOL dial clockwise or counter-
clockwise. The display message will change as
follows:
AF Û REG Û LANGUAGE Û AF
. To activate or deactivate the AF and REG mode,
briefly push the ENTER button when AF or REG
appears on the display and turn the MENU/VOL
dial clockwise or counterclockwise to switch
between the off or on position. After selection,
push the ENTER button to confirm the settings.
— When the AF mode is enabled, the audio unit
will automatically re-tune to a stronger fre-
quency if the radio signal becomes weak.
— When the REG mode is enabled, the audio unit
will maintain and maintain the station which is
broadcasting local (regional) programmes.
. To change the display language, briefly push the
ENTER button when LANGUAGE appears on the
display then turn the MENU/VOL dial clockwise or
counterclockwise to select the appropriate lan-
guage setting.
ENGLISH Û DUTCH Û FRENCH Û SPANISH
Û GERMAN Û ITALIAN Û PORTUGUESE Û
ENGLISH
After selecting the preferred language, push the
ENTER button to exit the menu.
To configure the SPEED volume and BEEP settings,
perform the following procedure:
1. Push the MENU button.
2. Turn the MENU/VOL dial clockwise or counter-
clockwise. The display message will change as
follows:
PHONE SETUP Û SPEED VOL Û CLOCK Û
BEEP Û PHONE SETUP
For phone operation, see “Bluetooth
®
Hands-Free
Phone System (if equipped for model without
navigation system)” (P.4-64).
. When SPEED VOL appears on the display, briefly
push on the ENTER button then turn the MENU/
VOL dial clockwise or counterclockwise to adjust
the level of the volume.
Adjusting the setting to 0 (zero) turns off the
speed volume feature. Increa sing th e speed
volume setting results in the audi o volume
increasing more rapidly with vehicle speed. Push
the ENTER button again to save the setting.
. When BEEP appears on the display, briefly push
the ENTER button and then turn the MENU/VOL
dial clockwise or counterclockwise to switch the
beep sound on or off. Push the ENTER button
again to save the setting.
After the preferred levels have been set, push the
MENU button to exit the menu or wait at least for 10
seconds without pressing any buttons.
FM-AM RADIO WITH COMPACT DISC (CD)
PLAYER AND NAVIGATION (if equipped)
GUID-3CD35F36-2CD C-49BE-A86A-02A0887F43E4
SAA2589
For details, see the separately provided NISSAN
Connect Owner’s Manual.
STEERING WHEEL SWITCH FOR AUDIO
CONTROL (if equipped)
GUID-40CA1AF7-B714-4 8E6-B8BC-A5690067503D
JVH0512X
Type A
JVH0005X
Type B
1. SOURCE select switch
2. VOLUME control switch
3. Tuning switch
The audio system can be operated using the controls
on the steering wheel.
SOURCE select switch
GUID-811ED559-6CFC-4067-ADEC-74EDDB357DA7
Push the source select switch to change the mode to
available audio source.
VOLUME control switch
GUID-03CE7E4A-30 F6-49F1-A221-5406070450BE
Push up or down the VOLUME control switch to
increase or decrease the volume.
Tuning switch
GUID-D7D0D2AF-C58A-40AA-A161-00120358D27C
Memory change (radio):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the tuning switch for less than 1.5 seconds to
change the next or previous radio preset.
SEEK tuning (radio):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the tuning switch for more than 1.5 seconds to
seek the next or previous radio station.
APS (Automatic Program Search) FF, APS REW
(CD, USB, iPod
®
):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the tuning switch for less than 1.5 seconds to
return to the beginning of the present program or skip
to the next program. Push several times to skip back or
skip through programs.
This system searches for the blank intervals between
selections. I f t here is a blank interval within one
program or there is no interval between programs,
the system may not stop in the desired or expected
location.
Push the tuning switch for more than 1.5 seconds to
fast forward or rewind through the track.
CD/USB MEMORY CARE AND CLEANING
GUID-626445F6-B0B9-49CA-AC1F-A3B0F19DEEE3
CD
GUID-14B8AB6E-6497-4F00-90D4-FE1C6DC63C99
SAA0451
. Handle a disc by its edges. Never touch the
surface of the disc. Do not bend the disc.
. Always place the discs in the storage case when
they are not being used.
. To clean a disc, wipe the surface from the center
to the outer edge using a clean, soft cloth. Do not
wipe the disc using a circular motion.
Do not use a conventional record cleaner or
alcohol intended for industrial use.
. A new disc may be rough on the inner and outer
edges. Remove the rough edges by rubbing the
inner and outer edges with the side of a pen or
pencil as illustrated.
USB memory device (if equipped)
GUID-7A78BF79-0F32-41D3-8678-81EEB2764082
. Do not touch the terminal portion of the USB
memory device.
. Do not place heavy objects on the USB memory
device.
. Do not store the USB memory device in highly
humid locations.
Monitor, Heater and air conditioner, and audio system 4-63

Related Topics

Popular Owner Manuals