2004-2009 Nissan Micra 4 Door Monitor, Heater and air conditioner, and audio system -> Bluetooth? Hands-Free Phone System (if equipped for model without navigation system) User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Monitor, Heater and air conditioner, and audio system -> Bluetooth? Hands-Free Phone System (if equipped for model without navigation system) for Your Nissan Micra 4 Door Third Generation (2004-2009)

4-64 Monitor, Heater and air conditioner, and audio system
. Do not expose the USB memory device to direct
sunlight.
. Do not spill any liquids on the USB memory
device.
Refer to the USB memory device Owner’s Manual for
the details.
GUID-3312FB98-F728-4E43-8A1B-E7F3F96AD38B
When installing a CB, ham radio or a car phone in your
vehicle, be sure to observe the following cautions,
otherwise the new equipment may adversely affect the
Engine Control System and other electronic parts.
CAUTION:
. Keep the antenna as far away as possible
from the Electronic Control Module.
. Keep the antenna wire at least 20 cm (8 in)
away from the Engine Control harnesses. Do
not route the antenna wire next to any
harnesses.
. Adjust the antenna standing wave ratio as
recommended by the manufacturer.
. Connect the ground wire from the radio
chassis to the body.
. For details, consult a NISSAN dealer.
NOTE:
For Europe:
For further information, visit the NISSAN web
site: Select your coun-
try from the list and go to the “SERVICES” menu.
If not available on the web site, contact a
NISSAN dealer.
GUID-C0019163-8F2F-4E73-8491-94964CD48309
WARNING:
. Use a phone after stopping your vehicle in a
safe location. If you have to use a phone
while driving, exercise extreme caution at all
times so full attention may be given to
vehicle operation.
. If a conversation in a moving vehicle re-
quires you to take notes, pull off the road to
a safe location and stop your vehicle before
doing so.
CAUTION:
To avoid draining the vehicle battery, use a
phone after starting the engine.
NOTE:
Wireless LAN (Wi-Fi) and the Bluetooth
®
func-
tions share the same frequency band (2.4 GHz).
Using the Bluetooth
®
and the wireless LAN
functions at the same time may slow down or
disconnect the communication and cause un-
desired noise. It is recommended that you turn
off the wireless LAN (Wi-Fi) when using the
Bluetooth
®
functions.
For model with navigation system, see the separately
provided NISSAN Connect Owner’s Manual.
Your NISSAN is equipped with the Bluetooth
®
Hands-
Free Pho ne System. If you are an owner of a
Bluetooth
®
enabled cellular phone, you can set up
the wireless connection between your cellular phone
and the in-vehicle phone module. With Bluetooth
®
wireless technology, you can make or receive a hands-
free telephone call with your cellular phone in the
vehicle.
CAR PHONE OR CB RADIO
Bluetooth
®
HANDS-FREE PHONE
SYSTEM (if equipped for model
without navigation system)
Once your cellular phone is paired to the in-vehicle
phone module, no other phone connecting procedure
is required. Your phone is automatically connected with
the in-vehicle phone module when the ignition switch
is placed in the “ON” position with the paired cellular
phone turned on and carried in the vehicle.
You can register up to 5 different Bluetooth
®
cellular
phones to the in-vehicle phone module. However, you
can talk on only one cellular phone at a time.
Before using the Bluetooth
®
Hands-Free Phone
System, refer to the following notes.
. Set up the wireless connection between a cellular
phone and the in-vehicle phone module before
using the system.
. Some Bluetooth
®
enabled cellular phones may not
be recognized by the in-vehicle phone module.
. You will not be able to use a Hands-free phone
under the following conditions.
— Your vehicle is outside of the telephone service
area.
— Your vehicle is in an area where it is difficult to
receive radio waves; such as in a tunnel, in an
underground parking garage, near a tall build-
ing or in a mountainous area.
— Your cellular phone is locked to prevent it from
being dialed.
When the radio wave condition is not ideal or ambient
sound is too loud, it may be difficult for the other party
to hear your voice during a call. Please close the
windows if possible.
Do not place the cellular phone in an area surrounded
by metal or far away from the in-vehicle phone module
to prevent tone quality degradation and wireless
connection disruption.
While a cellular phone is connected through the
Bluetooth
®
wireless connection, the battery power of
the cellular phone may discharge quicker than usual.
The Bluetooth
®
Hands-Free Phone System cannot
charge cellular phones.
Refer to the cellular phone Owner’s Manual regarding
the telephone charges, cellular phone antenna and
body, etc.
This wireless hands-free system is based on Blue-
tooth
®
technology.
. Frequency: 2402 MHz - 2480 MHz
. Output Power: 4.14 dBm EIRP
. Modulation: FHSS GFSK 8DPSK, p/4DQPSK
. Number of Channel: 79
. This wireless equipment cannot be used for any
services related to safety due to the possibility of
radio interference
REGULATORY INFORMATION
GUID-25D0ACED-D43F-490A-8418-3E946C5DB1DC
Bluetooth
®
is a trademark owned
by Bluetooth SIG, Inc. and li-
censed to Clarion Co., Ltd. and
Daewoo IS Corp.
CE STATEMENT
GUID-416E4A9B-CAB9-4F48-835D-F95D3FF6EC40
Hereby “Clarion Co., Ltd.” and Daewoo IS Corp.
declares that this Bluetooth car kit AV System is in
compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
NSY0105
HANDS-FREE PHONE SYSTEM (Type A)
GUID-AF80CC7C-7089-4082-A3CA-43A5828992D3
JVH0006X
For Europe
JVH0046X
For South Africa
1. PHONE SEND button
2. PHONE END/BACK button
3. PHONE BOOK button
The following options can be selected:
. Paired list
. Pair phone
. Delete phone
. Bluetooth
®
connection
. Delete phone book
Monitor, Heater and air conditioner, and audio system 4-65
4-66 Monitor, Heater and air conditioner, and audio system
. My number
Pairing procedure
GUID-BF64A5E4-2BB9-4D3F-9303-CAE35D7CF83D
If you wish to make a Bluetooth
®
connection for the
first time between your cellular phone and the Blue-
tooth
®
system of the audio unit, perform the following
pairing procedure.
1. Place the ignition switch in the “ACC” position.
2. Switch on the audio system and your cellular
phone.
For the vehicle:
1. Briefly push the MENU button.
2. Push the ENTER button.
3. Turn the MENU/VOL dial and select PAIR PHONE
then push the ENTER button.
4. The display shows READY TO PAIR then PASS-
CODE=1234.
On the cellular phone:
1. Activate the Bluetooth
®
connection.
2. Activate the search mode for Bluetooth
®
equip-
ment. Refer to the owner’s manual of your cellular
phone for further details. If the search mode finds
the device, it will be shown on your cellular phone
display.
3. Select the device name MY CAR.
4. Enter the passcode number 1234 as shown on
the display of the audio unit with the keypad on
your cellular phone and then push the confirmation
button on your cellular phone.
Action Screen display
Push briefly MENU button
; PHONE SETUP
Push ENTER
;
Turn VOLUME dial PAIR PHONE
;
Push ENTER
READY TO PAIR
PASSCODE=1234
;
Your cellular phone setup:
select MY CAR then enter
1234
;
If successful PAIRING OK
;
CONNECT OK
Mobile 1 *1
PAIR PHONE
Push
for the main
screen.
*1: Mobile name
Once the connection is finalized, the audio unit will
automatically register the cellular phone and the audio
unit display shows PAIRING OK and CONNECT OK. If
it fails to register, the display shows PAIRING FAIL
then start the procedure, previously described, again
or consult the owner’s manual of your cellular phone.
You can register up to 5 different Bluetooth
®
cellular
phones. However, you can only use one cellular phone
at a time. If you have 5 different Bluetooth
®
cellular
phones registered, a new cellular phone can only
replace one of the 5 existing paired phones. Use DEL
PHONE to delete one of the existing paired phones.
Paired phone list
GUID-8FD4AF0F-878C-461C-8CBE-7AD191238321
The paired phone list shows which phones have been
paired or registered with the Bluetooth
®
system. If the
list contains multiple phones then you can select the
appropriate phone to connect with the Bluetooth
®
system.
Action Screen display
Briefly push
MENU
; PHONE SETUP
Push ENTER
; PAIRED LIST
Push ENTER
; Mobile 1
Turn MENU/
VOL dial
Mobile 2
;
Push ENTER PLEASE WAIT
;
CONNECT OK
CONNECT
FAIL
PAIRED LIST
Push
for
the main screen.
In the above example procedure, “Mobile 2” will be
connected.
Removing a paired phone
GUID-72778B53-BB5A-4C47-9A36-9C3D67C5246B
Deletes the connection between the Bluetooth
®
system and the registered cellular phone.
Action Screen display
Briefly push MENU
; PHONE SETUP
Push ENTER
;
Turn MENU/VOL dial
; DEL PHONE
Push ENTER
; Mobile 1
Turn MENU/VOL dial Mobile 2
;
Push ENTER DELETE? <YES>
;
Push ENTER * DELETED
; DEL PHONE
Push
for the main
screen.
*: For the “Mobile 2” connection the screen
displays “DISCONNECTED”, followed by “Mo-
bile 2”, then “DELETED”.
In the above example, “Mobile 2” will be deleted while
“Mobile 1” remains connected to the system.
Bluetooth
®
activation
GUID-BF05010A-DED3-472E-8F60-FACA65775EF5
Activates or deactivates the Bluetooth
®
function. You
will need to activate the Bluetooth
®
function in order to
enable your hands-free phone system (except in the
pairing mode when it will be activated automatically).
Action Screen display
Push MENU
; PHONE SETUP
Push ENTER
;
Turn MENU/VOL dial BLUETOOTH
;
Push ENTER B’TOOTH <OFF>
;
Turn MENU/VOL dial B’TOOTH <ON>
;
Push ENTER BLUETOOTH
Push
for the main
screen.
Displaying MY NUMBER
GUID-CC38BD46-1CC9-4826-BA29-BD5ACC75DAB8
If your cellular phone is equipped with the function, the
phone number of the active cellular phone will be
displayed on the hands-free phone system.
Delete phone book list
GUID-80973A26-DCD9-46F6-82C2-AF0A9B4FD632
To delete all the contacts from the phone book,
proceed as follows:
Action Screen display
Briefly push MENU
; PHONE SETUP
Push ENTER
;
Turn MENU/VOL dial DEL P.BOOK
;
Push ENTER DEL ALL? <NO>
;
Turn MENU/VOL dial DEL ALL? <YES>
;
Push ENTER DELETING
DELETED
DEL P.BOOK
Push
for the main
screen.
Phone book
GUID-AFB80D0F-6A98-40E1-B6FC-9F2C09FADD3E
When the phone book button is pushed, the
following options can be selected by turning the
MENU/VOL dial in either direction.
. SEARCH
. Names (contact names)
. Speed dial mode [1Name (contact name)]
. DELETE NAME
. EDIT NAME
. ADD NAME
. Send name using Bluetooth
®
technology [
ADD NAME]
. Send all the phone book entries in the cellular
phone using Bluetooth
®
technology [
DOWNLOAD]
Monitor, Heater and air conditioner, and audio system 4-67
4-68 Monitor, Heater and air conditioner, and audio system
The phone book can store up to 250 names with
numbers and can be selected for calling. To add a
contact to the phone book proceed as follows:
Action Screen display
Push with a long push
button
; ADD NAME
Push ENTER
; ENTER NAME
Turn MENU/VOL dial ABC
;
Focus on “J”
IJK
Push ENTER
;
Turn MENU/VOL dial
Focus on “O”
NOP
;
Push ENTER
;*1 *3 JO
Turn MENU/VOL dial OK
;
Push ENTER
; ENTER NUMBER
Push ENTER then turn MENU/
VOL dial
1
; *2 *3
Push ENTER 123456789
;
Turn MENU/VOL dial
; OK
Push ENTER
SAVED
NOTE:
In the above example the contact name JO and
phone number 123456789 will be added.
*1: To insert special characters select the following
character options A: Alphabetic characters, 1/2:
Numerical characters, A
¨
: Latin characters and
@: Symbol characters.
*2: Select the number then confirm your selection
by pushing the ENTER button, and then proceed
likewise for every number.
*3: To correct an entry, briefly push the
button
then enter the correct details. To delete all
characters push the
button for more than 1
second.
NOTE:
You can also store the name and the phone
number in one of the six preset buttons on the
audio unit for frequently used phone numbers.
Transferring an entry to the phone book:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
You can also send a name (contact) from a connected
cellular phone to the phone book using Bluetooth
®
technology.
Action Screen display
Briefly push
button
;
Turn MENU/VOL dial
ADD NAME
;
Push ENTER SEND NAME
; *1 *2 JOE
Push ENTER
; *3 0123456789
Push ENTER SAVED YES
;
Push ENTER SAVED
;
ADD NAME
Push
for the main screen.
*1: The Bluetooth
®
icon will blink for 2 minutes.
*2: Send the name via the registered cellular phone
within the 2 minutes.
*3: Phone number is displayed.
Transferring all phone book entries at the same
time:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
If your cellular phone is equipped with the function, you
can download all the phone book entries in the cellular
phone to the hands-free system at the same time.
Action Screen display
Briefly push
button
;
Turn MENU/VOL dial
DOWNLOAD
;
Push ENTER
; APPEND?
Turn MENU/VOL dial OVERWRITE?
;
Push ENTER
DOWNLOAD-
ING...
DOWNLOAD OK
DOWNLOAD
Push
for the menu
screen.
NOTE:
. If you select APPEND, downloaded entries
will be saved in the available space without
deleting previously saved information in the
hands-free system. If there is not enough
space, the downloaded entries that exceed
the space available will not be saved and
MEMORY FULL appears on the display.
. If you select OVERWRITE, the downloaded
entries will be saved on top of the previously
saved information. (The previously saved
information will not be saved.) You can save
up to 250 entries. If you attempt to download
more than 250 entries, the remaining entries
w ill not be saved and MEMORY FULL
appears on the display.
Edit
GUID-54A2951A-B5B8 -4161-862D-560E88062263
You can edit a name or phone number stored in the
phone book.
Action Screen display
Push
button
;
Turn MENU/VOL dial
; EDIT NAME
Push ENTER
;*1
Turn MENU/VOL dial JOE
;
Push ENTER
; JOE OK <@OKA>
Turn MENU/VOL dial
; Focus on “Y” JOE <XYZ>
Push ENTER
; *2*3 JOEY
Push
for more than
1.5 seconds to go to main
screen.
*1: Alternatively use the SEARCH mode to select
the appropriate entry to edit.
— SEARCH appears on the display then push the
ENTER button.
— Select the first character of the name then push
the ENTER button.
— The name should be displayed. If necessary, turn
the MENU/VOL dial to select the correct name.
*2: When the
button is pushed briefly, the
cursor will move one step backwards and the
last character will be deleted. To delete all
characters push the
button for more than 1
second.
*3: If necessary, you can edit the telephone number.
After editing the name, select OK then push the
ENTER button to confirm and edit the number as
described for name editing.
Delete a name:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To delete a name (contact) from the phone book,
proceed as follows:
1. Briefly push the
button.
2. Turn the MENU/VOL dial then select the DELETE
NAME.
3. Push the ENTER button.
4. Turn the MENU/VOL dial to the name that needs
to be deleted then push the ENTER button.
5. The display will show DELETE? YES. If applicable,
turn the MENU/VOL dial to select DELETE? NO.
6. The display will show the message DELETED.
The search mode can also be performed as follows:
1. Briefly push the
button.
2. SEARCH appears on the display then push the
ENTER button.
3. Select the first character of the name then push
the ENTER button.
4. The display will now show the name(s) beginning
with the corresponding character. If necessary,
turn the MENU/VOL dial to select the correct
name.
5. Push the ENTER button and the display will show
DELETE? YES. If applicable, turn the MENU/VOL
dial to select DELETE? NO.
6. To confirm the selection, push the ENTER button.
Speed dial buttons:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
After entering the names and phone numbers, you can
assign the six preset buttons to the most frequently
dialled phone numbers.
1. Push the
button.
2. Select the name by turning the MENU/VOL dial or
using the search name mode.
3. Once found, push the assigned preset button until
a confirmation beep is heard. The name and phone
number are now stored under that button.
Hands-free phone control
GUID-B93C0DB4-53F9-4DD1-A870-91CEB3B4AA29
The hands-free mode can be operated using the
telephone button controls on the audio unit or on the
steering wheel.
Monitor, Heater and air conditioner, and audio system 4-69
4-70 Monitor, Heater and air conditioner, and audio system
Initiating a call:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
A call can be initiated using one of the following
methods:
. redial
. phone book
. voice tag
. speed dial (preset buttons)
NOTE:
During the active call you can adjust the micro-
phone volume by briefly pushing the MENU
button then adjusting the volume by turning
the MENU/VOL dial within the value range of −2
to +2. To confirm the entry, briefly push the
ENTER or
button or wait for 10 seconds to
return to the active call main screen.
Redial:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Use the redial mode to call the last number that was
dialled.
1. Briefly push the
button.
2. Select REDIAL.
3. Push the ENTER or the
button to redial the
last number.
Make a call from the phone book:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
In order to dial a contact from the phone book, proceed
as follows:
1. Push the
button.
2. Turn the MENU/VOL dial and select the corre-
spondent name.
3. Push the ENTER or the
button in order to dial
the number.
Alternatively, you can use the search mode as follows:
1. Briefly push the
button.
2. SEARCH appears on the display then push the
ENTER button.
3. Select the first character of the name then the
ENTER button.
4. The name should be displayed.
If necessary, turn the MENU/VOL dial to select the
correct name.
5. Push the ENTER or
button in order to dial the
number.
Calling via voice tag:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
If your cellular phone supports voice recognition, it is
possible to make a call via the voice tag instead of
manual selection, provided the name and number of
your contact has been previously marked and stored in
the phone book of your cellular phone. For details, see
the cellular phone manufacturer’s owner’s manual.
In order to dial via a voice tag, proceed as follows:
1. Push the
button for more than 2 seconds.
2. The display shows SPEAK NOW.
3. Give your voice tag.
Say the voice tag clearly and normally in the
direction of the microphone (located in the ceiling
in front of the rearview mirror).
4. If the voice tag is correct, the phone system will
dial the corresponding number.
Make a call via speed dial:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
To make a speed dial call using one of the assigned
preset buttons, proceed as follows:
1. Briefly push the
button.
2. Push the corresponding preset button (1-6).
Alternatively, you can select the corresponding
preset number by turning the MENU/VOL dial
instead of pushing the preset button.
3. To confirm the selection, push the
button to
make the call.
Receiving a call
GUID-3B2568E4-EF9B-408C-A309-FA648AE9E84D
When receiving an incoming call, the display will show
the caller identification (or NO NUMBER) and you can:
. answer the call by briefly pushing the
button.
. end the call after the conversation by pushing the
button.
. reject the call by pushing the
button.
Steering wheel switch for Bluetooth
®
GUID-6042BBB6-6991-4CA8-86F3-C3751FE5F330
SAA2594
The hands-free mode can be operated using the
controls on the steering wheel.
Volume control switch:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The volume control switch allows you to adjust the
volume of the speakers by pushing the + or − buttons
*
1
.
Telephone button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The and buttons
*
2
allows you to:
. accept an incoming call by pushing the
button.
. reject an incoming call by pushing the
button
during the incoming call.
. end an active call by pushing the
button
once.
. redial the last outgoing call by pushing the
button twice.
. make a speed dial call by pushing the
button then push the scrolling (up/down) switch to
scroll through the preset buttons for the stored
phone numbers. To confirm the selection push the
button to make the call.
. make a call via voice dialling by pushing the
button for more than 2 seconds then say
the voice tag clearly.
HANDS-FREE PHONE SYSTEM (Type B)
GUID-0370979A-D4D1-421D-B957-4B77E149534F
JVH0519X
Buttons:
1. Phone button
2. A-Z button
3. ENTER dial
4. SETUP button
Microphone:
The microphone is located near the map light.
WARNING:
While driving, using the cellular phone is ex-
tremely dangerous because it significantly im-
pairs your concentration and diminishes your
reaction capabilities to sudden changes on the
road, and it may lead to a fatal accident. This
applies to all phone call situations such as when
receiving an incoming call, during a phone
conversation, when calling through the phone
book search, etc.
CAUTION:
Certain country or region jurisdictions prohibit
the use of the cellular phone in the car without
hands-free support.
This chapter provides information about the NISSAN
hands-free phone system using a Bluetooth
®
connec-
tion.
Bluetooth
®
is a wireless radio communication stan-
dard. This system offers a hands-free feature for your
cellular phone to enhance driving comfort.
In order to use your cellular phone with the Bluetooth
®
of the audio system, the cellular phone must first be set
up. Once it has been set up, the hands-free mode is
automatically activated on the registered cellular phone
(via Bluetooth
®
) when it comes into range.
A notification message appears on the audio display
when the phone is connected, when an incoming call
is being received, as well as when a call is initiated.
When a call is active, the audio system, microphone
(located in the ceiling in front of the rearview mirror),
and steering wheel switches enable hands-free com-
munication.
If the audio system is in use at the time, the radio, CD,
or AUX source mode will be muted and will stay muted
until the active call has ended.
The Bluetooth
®
system may not be able to connect
with your cellular phone for the following reasons:
. The cellular phone is too far away from the vehicle.
. The Bluetooth
®
mode on the cellular phone has
not been activated.
. The cellular phone has not been paired with the
Bluetooth
®
system of the audio unit.
. The cellular phone does not support Bluetooth
®
technology (BT Core v1.2, Hands Free Profile v1.0
and Object Push Profile v1.0).
NOTE:
For details, see the cellular phone’s owner’s
manual.
Hands-free phone setup
GUID-AD3A95BD-3F84-45D9-B2E5-32F97EED83EE
To set up the Bluetooth
®
system to pair with (connect
or register) a preferred cellular phone, push the
button, select the Bluetooth
®
key, and then push the
dial. It is also possible to display the set up menu
directly by pushing the
button.
. Pair Device
Bluetooth
®
cellular phones can be paired with the
system. A maximum of 5 cellular phones can be
registered.
. Select Device
Paired Bluetooth
®
cellular phones are listed on the
display and can be selected for connection.
Monitor, Heater and air conditioner, and audio system 4-71
4-72 Monitor, Heater and air conditioner, and audio system
. Delete Device
A registered Bluetooth
®
cellular phone can be
deleted.
. On/Off
If this setting is turned off, the connection between
the Bluetooth
®
devices and the in-vehicle Blue-
tooth
®
module will be cancelled.
When successfully paired, a notification message will
be displayed. During the connection the following
status icons will be displayed (top left of display):
Signal strength (
), Battery status ( ) and
Bluetooth
®
( ).
*: If the low battery message comes on, the Bluetooth
®
device must be recharged soon.
Making a call
GUID-5EDE54C4-3C12-4043-B578-F240AEE44DC7
The hands-free mode can be operated using the
button on the audio system, or on the steering wheel.
Initiating a call:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
A call can be initiated using one of the following
methods:
. Redial
. Phone book
. Manual dialling
. Missed calls
. Dialled calls
. Received calls
Redial:
To redial or call the last number dialled, push the
Phone button for more than 2 seconds.
Making a call from the phone book:
NOS2763
Once the Bluetooth
®
connection is made between the
registered cellular phone and the audio system, phone
book data will be transferred automatically to the audio
system. The transfer may take a while before comple-
tion.
The phone book data is available only when the phone
is connected to the system. The system downloads the
latest phone book data each time the phone i s
connected.
To dial a contact from the phone book proceed as
follows:
1. Push the “Phone” button.
2. Turn the
dial to scroll down to Phone Book
and then push the
dial.
3. Scroll down through the list, select the appropriate
contact name (highlighted), and push the
dial.
4. A screen will show the number to be dialled. If
correct, push the
dial again to dial the
number.
If there are numbers assigned for the contact’s
(home), (cellular phone) or (office), scroll
to select the appropriate number to dial.
Alternatively, the quick search mode can be used as
follows:
1. Push the
button.
2. Turn the
dial for th e first alphabetic or
numerical letter of the contact name. Once high-
lighted, push the
dial to select the letter.
3. The display will show the corresponding contact
name(s). Where necessary, use the
dial
again to scroll further for the appropriate contact
name to call.
4. A screen will show the number to be dialled. If
correct, push the
dial again to dial the
number.
Manually dialling a phone number:
NOS2764
WARNING:
Park the vehicle in a safe location, and apply the
parking brake before making a call.
To dial a phone number manually use the audio system
display (virtual keyboard pad) as follows:
1. Push the
button, and turn the dial to
highlight “Call Number”.
2. Push the
dial to select “Call Number”.
3. Turn the dial to scroll along, and select each
number of the phone number. Once highlighted,
push the
dial after each number selection.
To delete the last number entered scroll to the “/”
(Backspace) symbol, and once highlighted push
the
dial. The last number will be deleted.
Pushing the
dial repeatedly will delete each
subsequent number.
4. After entering the last number, scroll to the “
”.
symbol, and push the
dial, or push the
button to dial the number.
Call lists:
A number from the dialled, received, or missed call lists
can also be used to make a call.
. Dialled call
Use the dialled call mode to make a call which is
based on the list of outgoing (dialled) calls.
. Received call
Use the received call mode to make a call which is
based on the list of received calls.
. Missed call
Use the missed call mode to make a call which is
based on the list of missed calls.
1. Push the
button, and select “Call Lists”.
2. Turn the
dial to scroll to an item, and push the
dial to select it.
3. Scroll to the preferred phone number and then
push the
dial, or push the button to dial
the number.
Receiving a call
GUID-38C6DFB3-7609-4197-B484-90CDF2540710
NOS2771
When receiving an incoming call, the display will show
the caller’s phone number (or a notification message
that the caller’s phone number cannot be shown):
. Answer the call by pushing the
button briefly,
or push the
dial.
. End the call, after the conversation, by:
— Pushing the
button briefly again.
— Pushing the
dial when the “ ” symbol
is highlighted.
If “
” is not highlighted, turn the dial to
“
” , and push the dial.
. Reject the call by selecting the “
” symbol on
the screen using the
dial and pushing the
dial to select it.
During a call:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
During a call, by scrolling and pushing the dial,
you can select the following options:
. “
” — Use this item to enter numbers during a
call. For example, if directed by an automated
phone system to dial an extension number the
system will send the tone associated with the
selected number.
. “
” — Use this item (the transfer handset
command) to transfer the call from the audio
system to your cellular phone.
To transfer the call back to hands-free via the
audio system select “
”.
Steering wheel switch for Bluetooth
®
GUID-FA7A0A09-E0B4-4302-A45C-75A575A6C0C5
JVH0528X
1. Volume control switch
2. Phone send/end button
The hands-free mode can be operated using the
controls on the steering wheel.
Volume control switch:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The volume control switch allows you to adjust the
volume of the speakers by pushing the + or − buttons.
Phone send/end button:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The and buttons can be used as follows.
. Push the
button to accept an incoming call.
. Push the
button to reject an incoming call.
. Push the
button to end an active call.
. Push and hold the
button to redial the last
outgoing call.
Monitor, Heater and air conditioner, and audio system 4-73

Related Topics

Popular Owner Manuals