2004-2009 Nissan Micra 4 Door Monitor, Heater and air conditioner, and audio system -> Rearview monitor (if equipped) User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Monitor, Heater and air conditioner, and audio system -> Rearview monitor (if equipped) for Your Nissan Micra 4 Door Third Generation (2004-2009)

4-2 Monitor, Heater and air conditioner, and audio system
GUID-7AE370BF-999D-4876-9D22-6D4228886738
WARNING:
. Do not adjust the heater and air conditioner
controls or audio controls while driving so
that full attention may be given to vehicle
operation.
. If you noticed any foreign objects entering
the system hardware, spilled liquid on the
system, or noticed smoke or fumes coming
out from the system, or any other unusual
operation is observed, stop using the system
immediately and contact the nearest
NISSAN dealer. Ignoring such conditions
may lead to an accident, fire or electric
shock.
. Do not disassemble or modify this system. If
you do, it may lead to an accident, fire, or
electric shock.
CAUTION:
Do not use the system when the engine is not
running for extended periods of time to prevent
battery discharge.
GUID-CC106B2E-5E79-4 2F8-99ED-0E1DA694C54F
When the shift lever is shifted into the “R” (Reverse)
position, the monitor display shows a rearward view
from the vehicle.
The system is designed as an aid to the driver in
situations such as slot parking or parallel parking.
Designs and items displayed on the screen may vary
depending on the models.
WARNING:
. The rearview monitor is a convenience but it
is not a substitute to check behind the
vehicle when backing up. T he driver is
always responsible for safety during parking
and other manoeuvres.
. Objects viewed in the rearview mo nitor
differ from actual distance because a wide-
angle lens is used. Objects in the rearview
monitor will appear visually opposite than
when viewed in the in side and outside
rearview mirrors.
. Make sure that the back door is securely
closed when backing up.
. Undern eath the bumper and the corner
areas of the bumper cannot be viewed on
the rearview monitor because of its mon-
itoring range limitation.
. Do not put anything on the rearview camera.
The rearview camera is installed above the
license plate.
. When washing the vehicle with high-pres-
sure water, be sure not to spray it around the
camera. Otherwise, water may enter the
camera unit causing water condensation on
the lens, a malfunction, fire or an electric
shock.
. Do not strike the camera. It is a precision
instrument. Otherwise, it may malfunction or
cau se dam age resulting in a fire or an
electric shock.
CAUTION:
Do not scratch the camera lens when cleaning
dirt or snow from the lens.
HOW TO READ DISPLAYED LINES
GUID-22FC5EF2-EDAB-4FB9-BAFF-4419FCFDAA54
SAA2776
Guide lines which indicate the vehicle width and
distances to objects with reference to the bumper line
*
A
are displayed on the monitor.
Distance guide lines:
Indicate distances from the vehicle body.
. Red line
*
1
: approx. 0.5 m (1.5 ft)
. Yellow line
*
2
: approx. 1 m (3 ft)
. Green line
*
3
: approx. 2 m (7 ft)
. Green line
*
4
: approx. 3 m (10 ft)
Vehicle width guide lines
*
5
:
Indicate the vehicle width when backing up.
SAFETY PRECAUTIONS REARVIEW MONITOR (if equipped)
DIFFERENCE BETWEEN PREDICTIVE AND
ACTUAL DISTANCES
GUID-153C5CCE-162B-4DA9-B3AE-660211DD5D1F
Backing up on a steep uphill
GUID-0392F0C9-7651-4856-B34B-662144B0FAF4
JVH0521X
When backing up the vehicle up a hill, the distance
guide lines and the vehicle width guide lines are shown
closer than the actual distance. For example, the
display shows 1 m (3 ft) to the place
*
A
, but the
actual 1 m (3 ft) distance on the hill is the place
*
B
.
Note that any object on the hill is viewed in the monitor
further than it appears.
Backing up on a steep downhill
GUID-92619D00-D1C0-47EF-A5A7-D3E5AFE953C4
JVH0522X
When backing up the vehicle down a hill, the distance
guide lines and the vehicle width guide lines are shown
further than the actual distance. For example, the
display shows 1 m (3 ft) to the place
*
A
, but the
actual 1 m (3 ft) distance on the hill is the place
*
B
.
Note that any object on the hill is viewed in the monitor
closer than it appears.
Backing up near a projecting object
GUID-7C76FA4A-2F94-47F8-A2F4-2F44E245F542
SAA3440
The vehicle may seem to nearly clear the object in the
display. However, the vehicle may hit the object if it
projects over the actual backing up course.
Monitor, Heater and air conditioner, and audio system 4-3
4-4 Monitor, Heater and air conditioner, and audio system
Backing up behind a projecting object
GUID-A5D2128B-7D88-4CF6-8FC1-15B8CA729DA8
JVH0523X
The position
*
C
is shown further than the position
*
B
in the display. However, the position
*
C
is actually at
the same distance as the position
*
A
. The vehicle
may hit the object when backing up to the position
*
A
if the object projects over the actual backing up
course.
MIRROR DISPLAY OPERATION
GUID-AF482621-1924-4560-804D-C01890516316
SAA3341
Rearview monitor on/off
GUID-DF911563-A6AE-4CF8-B1C7-82918B712666
The rearview monitor
*
C
is displayed automatically
when the shift lever is moved to the “R” (Reverse)
position.
To turn off the rearview monitor
*
C
, push the POWER
ON/OFF button
*
A
. The indicator light
*
B
will
illuminate in orange.
To return to the display the rearview monitor
*
C
, push
the POWER ON/OFF button
*
A
again or turn the
ignition switch to the “OFF” position. The indicator light
*
B
will illuminate in green.
To set the rearview monitor to be always not displayed,
push and hold the POWER ON/OFF button
*
A
for
12 seconds or more when the shift lever is in the “R”
(Reverse) position. The indicator light
*
B
turns off and
then turns back on in approximately 2 seconds.
Whenever the rearview monitor is off, by switching the
ignition switch to the “ON” position and then pressing
the POWER ON/OFF button
*
A
while the shift lever
is in the “R” (Reverse) position, the rearview monitor
will be displayed again on the mirror display.
Language select mode
GUID-46C14C4F-0D35-49B6-A80E-4C226EDC5806
To change the language of the warning text displayed
on the mirror display, push and hold the POWER ON/
OFF button
*
A
for 6 to 11 seconds when the shift
lever is in the “R” (Reverse) position. When the
language select screen is displayed push the POWER
ON/OFF button
*
A
repeatedly until the preferred
language is displayed.
If the button is not pushed for approximately 5
seconds, the language select mode will auto-
matically return to the normal mode.
OPERATING TIPS
GUID-0948ED57-AAA2-4673-B51F-E223BE3C9B9E
. When the view is switched, the display images on
the screen may be displayed with some delay.
. When the temperature is extremely high or low,
the screen may not clearly display objects. This is
not a malfunction.
. When strong light is directly coming on the
camera, objects may not be displayed clearly.
This is not a malfunction.
. Vertical lines may be seen in objects on the
screen. This is due to strong reflected light from
the bumper. This is not a malfunction.
. The screen may flicker under fluorescent light. This
is not a malfunction.
. The colors of objects on the rearview monitor may
differ somewhat from the actual color of objects.
This is not a malfunction.
. Objects on the monitor may not be clear in a dark
environment. This is not a malfunction.
. If dirt, rain or snow accumulates on the camera,
the rearview monitor may not display objects
clearly. Clean the camera.

Related Topics

Popular Owner Manuals