2006-2014 Nissan Qashqai SUV In case of emergency User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

In case of emergency for Your Nissan Qashqai SUV First Generation (2006-2014)

6 In case of emergency  
Spare tyre................................................................ 6-2  
Temporary-use spare tyre ................................... 6-2  
Flat tyre ................................................................... 6-2  
Stopping the vehicle ........................................... 6-2  
Changing flat tyre (Models with spare wheel,  
where fitted) ....................................................... 6-3  
Repairing flat tyre (Models with emergency  
tyre puncture repair kit, where fitted)................... 6-7  
Jump-starting ........................................................... 6-10  
Push-starting ........................................................... 6-12  
Engine overheat....................................................... 6-12  
Tow truck towing ..................................................... 6-13  
Towing precautions ............................................ 6-13  
Recommended towing for two-wheel drive  
(2WD) models.................................................... 6-14  
Recommended towing for four-wheel drive  
(4WD) models.................................................... 6-14  
Towing eye......................................................... 6-15  
Freeing the vehicle from sand, snow or mud ....... 6-15  
Downloaded from manuals search engine  
SPARE TYRE  
FLAT TYRE  
Avoid driving over obstacles. Also, do not take  
the vehicle through an automatic car wash.  
In case of a flat tyre, follow the instructions as de-  
scribed below:  
•
TEMPORARY-USE SPARE TYRE  
Avoid driving sharp turns and abrupt braking.  
STOPPING THE VEHICLE  
•
•
Do not exceed the vehicle’s maximum load  
rating or the load-carrying capacity molded  
on the sidewall of the temporary-use spare  
tyre.  
WARNING  
Make sure that the handbrake is securely ap-  
plied.  
•
Do not use a snow chain on this tyre because  
it will not fit properly. This could cause dam-  
age to the vehicle and result in loss of the  
chain.  
•
For Manual Transmission (MT) models: Make  
sure the gear lever is in the R (Reverse) posi-  
tion.  
•
NCE069Z  
Temporary-use spare tyre label  
For Automatic Transmission (AT) or Continu-  
ously Variable Transmission (CVT) models:  
Make sure that the selector lever is in the P  
(Park) position.  
Do not use the temporary-use spare tyre on  
any other vehicle because this tyre has been  
designed specifically for your vehicle.  
•
•
The temporary-use spare tyre is designed for emer-  
gency use only. This spare tyre should be used  
ONLY for very short periods and NEVER be used  
for long drives or extended periods.  
The vehicle must not be driven with more than  
one temporary-use spare tyre at the same  
time.  
Never change tyres when the vehicle is on a  
slope, ice or a slippery area. This is hazard-  
ous.  
•
Observe the following precautions if the temporary-  
use spare tyre must be used, otherwise your vehicle  
could be damaged or involved in an accident.  
Do not tow a trailer.  
•
•
Never change tyres if oncoming traffic is close  
to your vehicle. Wait for professional road as-  
sistance.  
•
As with all tyres, the temporary-use spare tyre  
must be checked regularly to ensure pres-  
sure is maintained.  
WARNING  
Any continuous road use of this tyre could result  
in tyre failure, loss of vehicle control, and pos-  
sible personal injury.  
1. Safely move the vehicle off the road, away from  
traffic.  
For pressure details, see the tyre placard lo-  
cated on the driver’s side centre pillar.  
2. Switch on the hazard warning flashers.  
3. Park on a level surface.  
CAUTION  
The temporary-use spare tyre should be used  
only in emergencies. It should be replaced by  
the standard tyre at the first opportunity.  
•
4. Apply the handbrake.  
5. Shift the gear lever (MT models) into the R (Re-  
verse) position [AT or CVT models, move the  
selector lever to the P (Park) position].  
Drive carefully and do not drive your vehicle  
faster than 80 km/h (50 MPH).  
•
6-2 In case of emergency  
Downloaded from manuals search engine  
6. Turn off the engine.  
Place suitable blocks j1 in front of and behind the  
wheel diagonally opposite the flat tyre jA to prevent  
the vehicle from moving when it is on the jack.  
5–seater:  
1. Open the back door.  
7. Open the bonnet (for details, see “Bonnet  
release” in the “3. Pre-driving checks and  
adjustments” section) in order to:  
2. Remove the luggage compartment floor cover.  
Getting the tools and spare wheel  
3. Remove the retainer j1 by turning it anti-clock-  
Warn other traffic.  
The spare wheel, jack and tools are located inside  
the luggage compartment.  
•
•
wise.  
Signal to professional road assistance that  
you require assistance.  
4. Carefully remove and place the subwoofer  
(where fitted) j2 on the top right-hand side cor-  
ner of the luggage floor compartment (with the  
flat surface facing downwards).  
8. Have all passengers exit the vehicle and stand in  
a safe place, away from traffic and clear of the  
vehicle.  
NOTE  
CHANGING FLAT TYRE (Models with  
spare wheel, where fitted)  
Be careful not to drop the subwoofer.  
5. Remove the jack, tools and spare wheel.  
NCE307  
without subwoofer  
Type A  
Type B  
jA  
jB  
MCE0001DZ  
Blocking the wheels  
WARNING  
Make sure to block the appropriate wheel to pre-  
vent the vehicle from moving, which may cause  
personal injury.  
NCE312  
5–seater, with subwoofer (where fitted)  
In case of emergency 6-3  
Downloaded from manuals search engine  
7–seater:  
Removing wheel cover (where fitted)  
1. Open the back door.  
WARNING  
2. Remove both sides and centre floor boards j1 .  
Take care when removing the wheel cover as the  
cover may detach suddenly.  
3. Remove tonneau cover (where fitted) j2 and  
floor cover j3 . For details, see “Rear parcel shelf  
(where fitted)” in the “2. Instruments and  
controls” section.  
Remove the wheel cover as illustrated with a suit-  
able tool or carefully remove the wheel cover with  
both hands.  
4. Lower the head restraints and fold the third row  
seat. For details, see “Seats” in the “1. Safety —  
seats, seat belts and supplemental restraint  
system” section.  
Removing the wheel  
WARNING  
5. Release the seat from its locking latches jA by  
pulling up the two levers simultaneously on both  
sides j4 .  
Make sure to read the caution label attached  
to the jack body before use.  
•
Do not get under a vehicle that is supported  
only by a jack: Use vehicle support stands.  
•
6. Lift up the seat j5 and release the levers.  
7. Remove the jack, tools and spare wheel.  
Use only the jack that is provided with your  
vehicle. The jack is designed only for lifting  
your vehicle during a tyre change.  
•
Do not use the jack provided with your vehicle  
on other vehicles.  
•
Use the correct jack-up points. Never use any  
other part of the vehicle for jack support.  
•
Never lift the vehicle more than necessary.  
•
SCE0173AZ  
Never use blocks on or under the jack.  
•
Do not start or run the engine while the ve-  
hicle is on the jack. The vehicle may move  
suddenly, and this may cause an accident.  
•
NCE304  
7–seater  
6-4 In case of emergency  
Downloaded from manuals search engine  
Never allow passengers to stay in the vehicle  
while it is on the jack.  
Make sure to keep the lock key in the vehicle.  
Otherwise, wheels cannot be removed and the  
service cannot be performed.  
•
•
•
Remove all loads before lifting the vehicle with  
the jack.  
Make sure to block the wheel diagonally op-  
posite the flat tyre as described earlier in this  
section.  
CAUTION  
NCE143Z  
The jack should be used on firm, level ground.  
4. Loosen each wheel nut by one or two turns  
anticlockwise with the wheel wrench.  
NCE309  
5–seater  
Do not remove the wheel nuts until the tyre is  
off the ground.  
Models with wheel lock nuts (where fitted):  
If the wheel is equipped with a wheel lock nut,  
insert the wheel lock key j1 and loosen it as pre-  
viously described.  
NCE256Z  
Jack-up points  
The wheel lock nut can only be removed with the  
wheel lock key. A key number is necessary if you  
need to duplicate the wheel lock key.  
1. Place the jack directly under the jack-up point as  
illustrated so that the top of the jack contacts the  
vehicle at the jack-up point.  
NCE308  
Record the key number as shown on the key  
code card on the “Security information” page at  
the end of this manual and keep it in a safe place,  
not in the vehicle. If you loose the wheel lock key,  
see your NISSAN dealer for a duplicate with the  
original wheel lock key code.  
7–seater  
2. Align the centre of both the jack head and the  
notches at the jack-up point as shown.  
5. To lift the vehicle, securely hold and turn the  
handle clockwise as shown.  
3. Fit the groove of the jack head between the two  
notches as shown.  
6. Carefully raise the vehicle until the tyre clears the  
ground.  
7. Remove the wheel nuts, then remove the wheel  
with the flat tyre.  
In case of emergency 6-5  
Downloaded from manuals search engine  
CAUTION  
Tighten  
Wheel nut tightening torque:  
113 N•m (12 kg-m, 83 ft-lb)  
jA  
jB  
jC  
The wheel is heavy. Be sure that your feet are  
clear of the wheel and use gloves as necessary  
to avoid injury.  
Loosen  
Bevelled face  
WARNING  
1. Clean any mud or dirt from the surface between  
the wheel and the hub.  
Retighten the wheel nuts after the vehicle has  
been driven for 1,000 km (600 miles) (also in  
cases of a flat tyre, etc.).  
Installing the wheel  
2. Carefully fit the wheel and tighten the wheel nuts  
with your fingers. Check that all the wheel nuts  
contact the wheel surface horizontally and on the  
bevelled side.  
WARNING  
The wheel nuts must be kept tightened to specifica-  
tion at all times. It is recommended that the wheel  
nuts be tightened to specification at each mainte-  
nance interval.  
The temporary use spare tyre is designed for  
emergency use. See “Spare tyre” earlier in  
this section.  
•
Models with wheel lock nut (where fitted):  
Never use wheel nuts other than those pro-  
•
Adjust the tyre pressure to the COLD pressure.  
Insert the wheel lock key into the wheel lock nut  
and tighten into the wheel finger tight.  
vided with your vehicle. Incorrect wheel nuts  
or improperly tightened wheel nuts may cause  
the wheel to become loose or come off. This  
could cause an accident.  
COLD pressure is the tyre pressure as measured  
after the vehicle has been parked for three hours or  
more or driven for less than 1.6 km (1 mile).  
3. With the wheel wrench, tighten the wheel nuts  
alternately and evenly in the sequence as illus-  
trated (j1 - j5 ) until they are tight.  
Never use oil or grease on the wheel studs or  
nuts. This may cause the wheel nuts to be-  
come loose.  
COLD tyre pressures are shown on the tyre placard  
affixed to the driver’s side centre pillar.  
•
4. Lower the vehicle slowly until the tyre touches  
the ground.  
Stowing the wheel and tools  
5. Tighten the wheel nuts securely using the wheel  
wrench in the sequence as illustrated.  
WARNING  
6. Lower the vehicle completely.  
7. Install the wheel cover (where fitted).  
NOTE  
Always make sure that the wheel, subwoofer  
(where fitted), jack and tools are properly stored  
after each use. Such items can become danger-  
ous projectiles in an accident or sudden stop.  
Before installation, align NISSAN logo (centre  
cap) with the wheel nuts/or perpendicular to  
valve hole (where fitted), to correctly align to  
the centre.  
5–seater  
1. Securely store the wheel with the flat tyre, the  
jack and the tools in the specified storage areas.  
See “Getting the tools and spare wheel” earlier  
in this section(for 5–seater).  
NCE287Z  
As soon as possible, tighten the wheel nuts to  
the specified torque with a torque wrench.  
6-6 In case of emergency  
Downloaded from manuals search engine  
2. Store the subwoofer (where fitted) as it was origi-  
nally installed.  
normal wheel nuts. For details, see “Chang-  
ing flat tyre (Models with spare wheel, where  
fitted)” earlier in this section.  
Wheel lock nuts (where fitted)  
In order to prevent theft, the specially designed  
wheel lock nut is installed to each wheel. The wheel  
lock nut cannot be removed with the commonly used  
tools.  
3. Install the retainer and replace the floor cover.  
NOTE  
The wheel lock nut has an individual code.  
•
A wheel lock key with other than the indi-  
vidual code cannot remove the wheel lock  
nut. If you lose the wheel lock key, contact  
a NISSAN dealer for a duplicate with the  
original wheel lock key code.  
When removing tyres, use the lock key provided  
with your vehicle.  
Record the key number as shown on the  
•
key code card on the “Security informa-  
tion” page at the end of this manual and  
keep it in a safe place, not in the vehicle.  
NCE306  
7–seater  
When you ask for a service at a NISSAN  
•
dealer or qualified workshop, make sure  
to keep the lock key in the vehicle. Other-  
wise, wheels cannot be removed and the  
service cannot be performed.  
1. Store the tools in the specified areas.  
NCE143Z  
2. Firmly pull down the third row seat and make  
sure it locks into the locking latches on both sides  
under the seat.  
Removing the wheel lock nut:  
REPAIRING FLAT TYRE (Models with  
emergency tyre puncture repair kit,  
where fitted)  
1. Insert the wheel lock key j1 to the wheel lock  
3. Place the seatback of the third row seat in the  
upright position j1 . For details, see “Folding 3rd  
row (7-seater)” in the “1. Safety — seats, seat  
belts and supplemental restraint system” section.  
nut.  
2. To remove the wheel lock nut, turn the wheel  
lock key anticlockwise using the wheel wrench.  
The emergency tyre puncture repair kit is supplied  
with the vehicle instead of a spare tyre. This repair  
kit must be used for temporarily fixing a minor tyre  
puncture. After using the repair kit, see a NISSAN  
dealer or qualified workshop as soon as possible for  
tyre inspection and repair/replacement.  
CAUTION  
4. Store the wheel with flat tyre vertically in the boot  
j2 .  
Do not use a power tool to remove the wheel  
lock nuts.  
•
5. Store the other items in following order:  
When installing the wheel, tighten the wheel  
lock nuts to the same tightening torque as the  
Tonneau cover (where fitted) j3 → Floor cover  
j4 → Centre floor board and the two side floor  
boards j5 .  
•
In case of emergency 6-7  
Downloaded from manuals search engine  
CAUTION  
Getting emergency tyre puncture repair  
kit  
Do not use the emergency tyre puncture repair  
kit under the following conditions. Contact a  
NISSAN dealer or qualified workshop or profes-  
sional road assistance.  
Take the emergency tyre puncture repair kit out of  
the boot. The repair kit consists of the following  
items:  
when the sealant has passed its expiration  
date (shown on the label attached to the  
bottle)  
•
Tyre sealant bottle  
Air compressor  
1.  
2.  
3.  
Speed restriction sticker  
when the cut or the puncture is approximately  
4 mm (0.16 in) or longer  
•
Before using emergency tyre puncture  
repair kit  
when the side of the tyre is damaged  
•
when the vehicle has been driven with a con-  
siderable loss of air from the tyre  
If any foreign object (for example, a screw or  
nail) is embedded in the tyre, do not remove it.  
•
•
when the tyre is completely displaced inside  
or outside the rim  
Check the expiration date of the sealant (shown  
on the label attached to the bottle). Never use a  
sealant which has passed its expiration date.  
•
•
when the tyre rim is damaged  
•
when two or more tyres are flat  
•
NCE322  
NCE314  
6-8 In case of emergency  
Downloaded from manuals search engine  
5. Screw the air compressor tube securely into the  
Repairing tyre  
After repairing tyre  
tyre valve jA .  
1. Shake the sealant bottle well.  
See a NISSAN dealer or qualified workshop for tyre  
repair/replacement as soon as possible.  
6. Insert its power plug to the power outlet jB in  
the vehicle. For details, see “Power outlet” in the  
“2. Instruments and controls” section.  
2. Remove the bottle cap and the orange plug from  
the top of the compressor.  
3. Screw the bottle into the opening of the com-  
pressor (where the orange plug was).  
7. Turn the ignition switch to the Acc position.  
8. Switch on the compressor, and inflate the tyre to  
the pressure that is specified on the tyre placard  
affixed to the driver’s side centre pillar.  
CAUTION  
Do not operate the compressor for more than 10  
minutes.  
If the tyre pressure does not increase to the speci-  
fied pressure within 10 minutes, the tyre may be  
seriously damaged and the tyre cannot be repaired  
with this tyre repair kit. Contact a NISSAN dealer  
or qualified workshop.  
NCE315  
4. Put the speed restriction sticker in a location  
where the driver can see it while driving.  
9. Remove the air compressor from the tyre valve.  
Immediately drive the vehicle at a speed of 80  
km/h (50 MPH) or less.  
10. After 10 minute or 5 km (3 mile) drive, check  
the tyre pressure. The temporary repair is com-  
pleted if the tyre pressure does not drop.  
If the tyre pressure is lower than specified, re-  
peat the steps from step 5.  
If the pressure drops again or under 130 kPa  
(19 psi), the tyre cannot be repaired with this  
tyre repair kit. Contact a NISSAN dealer or  
qualified workshop.  
NCE316  
In case of emergency 6-9  
Downloaded from manuals search engine  
JUMP-STARTING  
Never lean over the battery while jump-start-  
ing.  
•
•
Never allow battery fluid to come into contact  
with eyes, skin, clothes or the vehicle’s  
painted surfaces. Battery fluid is a corrosive  
sulphuric acid which can cause severe burns.  
If the fluid comes into contact with anything,  
immediately flush the contacted area with  
plenty of water.  
Keep the battery out of the reach of children.  
•
•
The booster battery must be rated at 12 volts.  
Use of an incorrectly rated battery will dam-  
age your vehicle.  
Never attempt to jump-start a frozen battery.  
It could explode and cause serious injury.  
•
1. Prepare vehicle jA with the booster battery for  
the vehicle jB being jump-started.  
CAUTION  
Do not allow the two vehicles to touch.  
2. Apply the handbrake.  
NCE259  
3. Shift the gear lever (MT models) into the N (Neu-  
tral) position [AT or CVT models, move the se-  
lector lever to the P (Park) position].  
Explosive hydrogen gas is always present in  
the vicinity of the battery. Keep all sparks and  
flames away from the battery.  
•
•
WARNING  
4. Switch off all unnecessary electrical systems  
(headlights, hazard lights etc,).  
Incorrect jump-starting can lead to a battery  
•
explosion. The battery explosion may result in  
severe injury or death. It may also result in  
damage to the vehicle. Be sure to follow the  
instructions in this section.  
Always wear suitable eye protection glasses  
and remove rings, bracelets, and any other  
jewellery whenever working on or near a bat-  
tery.  
5. Ensure that the ignition switch of the vehicle be-  
ing jump-started is in the LOCK position.  
6-10 In case of emergency  
Downloaded from manuals search engine  
6. Open the bonnet. For details, see “Bonnet  
release” in the “3. Pre-driving checks and  
adjustments” section.  
CAUTION  
If the battery terminal is disconnected (for bat-  
tery replacement, etc.) and then reconnected,  
there may be some delay before the Stop/  
Start System reactivates.  
•
Do not keep the starter motor engaged for  
more than 10 seconds. If the engine does not  
start immediately, turn the ignition switch to  
“OFF” and wait 10 seconds before trying  
again.  
7. Remove the vent caps (where fitted) on the bat-  
tery and cover the battery with an old cloth.  
8. Connect the jump leads in the sequence (j1 →  
j2 → j3 → j4 ) as illustrated.  
11. After starting the engine of your vehicle, care-  
fully disconnect the negative lead and then the  
positive lead ( j4 → j3 → j2 → j1 ).  
CAUTION  
Always connect positive j+ to positive j+  
•
12. Remove and dispose of the cloth that was used  
to cover the vent holes as it may be contami-  
nated with corrosive acid.  
and negative j- to body ground (for ex-  
ample, engine lift bracket, etc.) – not to  
the battery’s negative j- .  
13. Install the vent caps (where fitted).  
14. Close the bonnet.  
NOTE  
An incorrect connection could damage the  
charging system.  
•
Be sure that the jumper cables do not  
touch moving parts in the engine compart-  
ment.  
•
For models which incorporate the Stop/Start  
System:  
Be careful not to allow contact between  
•
Ensure that the battery fitted is the special  
•
the positive jump lead connector and the  
vehicle or the negative lead during con-  
nection and disconnection.  
battery that is enhanced with regard to the  
charge-discharge capacity and life perfor-  
mance. Avoid using any other battery for the  
Stop/Start System, as this may cause early  
deterioration of the battery or a malfunction  
of the Stop/Start System. It is recommended  
that a Genuine NISSAN battery is fitted. For  
more information, contact a NISSAN dealer or  
qualified workshop  
9. Start the engine of the other vehicle jA and let it  
run for a few minutes. Keep the engine speed at  
about 2,000 rpm.  
10. Start the engine of your vehicle jB in the nor-  
mal way.  
In case of emergency 6-11  
Downloaded from manuals search engine  
PUSH-STARTING  
ENGINE OVERHEAT  
CAUTION  
4. Shift the gear lever (MT models) into the N (Neu-  
tral) position [AT or CVT models, move the se-  
lector lever to the P (Park) position].  
WARNING  
Three-way catalyst equipped models should  
not be started by pushing the vehicle as the  
three-way catalyst may be damaged.  
•
Never continue driving if the engine of your  
vehicle overheats. Doing so could cause a ve-  
hicle fire.  
•
DO NOT STOP THE ENGINE.  
Automatic transmission (AT) or continuously  
5. Open all windows.  
•
Never open the bonnet if steam is coming  
out.  
•
variable transmission (CVT) models cannot be  
started by pushing the vehicle. This may cause  
transmission damage.  
6. Switch off the air conditioner system (where fit-  
ted).  
Never remove engine coolant reservoir cap  
•
7. Set the heater or air conditioner temperature  
control to maximum “HOT” and fan speed con-  
trol to maximum speed.  
when the engine is hot. If the engine coolant  
reservoir cap is removed while the engine is  
hot, pressurised hot water will spurt out and  
possibly cause burning, scalding or serious  
injury.  
Never try to start the vehicle by towing it; when  
•
the engine starts, the forward surge could  
cause the vehicle to collide with the tow ve-  
hicle.  
8. Exit the vehicle.  
9. Visually inspect and listen for steam or coolant  
escaping from the radiator before opening the  
bonnet. Wait until no steam or coolant can be  
seen before proceeding.  
If steam or coolant is coming out of the en-  
gine, stand clear of the vehicle to prevent get-  
ting injured.  
•
The engine cooling fan will start whenever the  
coolant temperature exceeds preset degrees.  
•
10. Open the bonnet. For details, see “Bonnet  
release” in the “3. Pre-driving checks and  
adjustments” section.  
Be careful not to allow your hands, hair, jewel-  
lery or clothing to come into contact with, or  
get caught in, the cooling fan or drive belts.  
•
11. Visually check if the cooling fan is running.  
12. Visually check the radiator and radiator hoses  
for leakage.  
If the engine of your vehicle is overheating (indi-  
cated by the engine coolant temperature gauge) or  
if you feel a lack of engine power, detect unusual  
noise, etc., proceed as follows:  
WARNING  
If coolant is leaking, the cooling fan belt is  
missing or loose or the cooling fan is not run-  
ning, stop the engine.  
1. Move and park the vehicle safely off the road and  
away from traffic.  
2. Turn on the hazard warning flasher lights.  
3. Apply the handbrake.  
13. After the engine cools down, check the coolant  
level in the engine coolant reservoir with the  
engine running.  
6-12 In case of emergency  
Downloaded from manuals search engine  
TOW TRUCK TOWING  
14. If the level is low, remove the engine coolant  
reservoir cap and add coolant slowly into the  
reservoir. After refilling the reservoir to the MAX  
level, install the reservoir cap.  
When towing your vehicle, local regulations for tow-  
ing must be followed. Incorrect towing equipment  
could damage your vehicle. To assure proper tow-  
ing and to prevent accidental damage to your ve-  
hicle, NISSAN recommends that you have a service  
operator tow your vehicle. It is advisable to have the  
service operator carefully read the following precau-  
tions.  
WARNING  
Before removing the engine coolant reservoir  
cap and to avoid the danger of being scalded,  
cover the reservoir cap with a rag and loosen  
the reservoir cap to the first notch to allow the  
steam to escape.  
WARNING  
Do not allow any occupants in the vehicle that  
is being towed.  
•
15. Close the bonnet.  
Never get under your vehicle after it has been  
lifted by a tow truck.  
•
Have your vehicle inspected or repaired by a  
NISSAN dealer or qualified workshop.  
TOWING PRECAUTIONS  
When towing: Make sure that the transmission,  
•
axles, steering system and power train are in  
working condition. If any unit is damaged, the  
vehicle must be towed using a dolly or be placed  
on a flat bed lorry.  
Release the handbrake and shift the manual  
•
transmission (MT), automatic transmission (AT)  
or continuously variable transmission (CVT) into  
the N (Neutral) position before starting to tow  
the vehicle.  
Always attach safety chains before towing.  
•
NCE302  
2WD models  
In case of emergency 6-13  
Downloaded from manuals search engine  
RECOMMENDED TOWING FOR  
TWO-WHEEL DRIVE (2WD) MODELS  
CAUTION  
RECOMMENDED TOWING FOR  
FOUR-WHEEL DRIVE (4WD) MODELS  
CAUTION  
NEVER tow automatic transmission (AT) or con-  
tinuously variable transmission (CVT) models  
with the front wheels on the ground or with all  
four wheels on the ground (forwards or back-  
wards), this may cause serious and expensive  
damage to the transmission. If it is necessary to  
tow the vehicle with the rear wheels raised, al-  
ways use towing dollies under the front wheels.  
NEVER tow the vehicle with any wheels on the  
ground as this may cause serious and expensive  
damage to the transmission.  
NISSAN recommends that towing dollies be used  
when towing your vehicle or that the vehicle be  
placed on a flat bed lorry as illustrated.  
When towing with the front wheels on towing dol-  
lies:  
NISSAN recommends that your vehicle should be  
towed with the driving (front) wheels off the ground  
or that the vehicle be placed on a flat bed lorry as  
illustrated.  
Turn the ignition switch to the “OFF” position, then  
secure the steering wheel in a straight ahead posi-  
tion using a rope or similar device. Never place the  
ignition switch in the LOCK position. This will re-  
sult in damage to the steering lock mechanism.  
When towing with the front wheels – on the  
ground (MT models only) or – on towing dollies:  
Turn the ignition switch to the “OFF” position, then  
secure the steering wheel in a straight ahead posi-  
tion using a rope or similar device. Never place the  
ignition switch in the LOCK position. This will re-  
sult in damage to the steering lock mechanism.  
NCE303  
4WD models  
6-14 In case of emergency  
Downloaded from manuals search engine  
TOWING EYE  
Towing eye usage  
The towing eye should be used in the event that  
your vehicle becomes trapped in sand, snow or mud,  
and is unable to drive away without being pulled,  
use the towing eye.  
Use the towing eye only, not other parts of the  
vehicle. Otherwise, the vehicle body will be dam-  
aged.  
•
Only use the towing eye to free a vehicle stuck  
in sand, snow, mud, etc.  
•
NCE283Z  
Never tow the vehicle for a long distance using  
only the towing eye.  
•
The towing eye is stored with the vehicle tools and  
located in the spare wheel recess (luggage com-  
partment area).  
The towing eye is under tremendous force when  
•
used to free a stuck vehicle. Always pull the cable  
straight out from the front of the vehicle. Never  
pull on the towing eye at a sideways angle.  
1) Remove the cover from the bumper.  
2) Securely install the towing eye, as illustrated.  
CAUTION  
Make sure that the towing eye is properly stored in  
its designated location after use.  
In order not to break the towing line, tension it  
slowly.  
FREEING THE VEHICLE FROM SAND,  
SNOW OR MUD  
WARNING  
Never allow anyone to stand near the towing  
line during the pulling operation.  
•
Never spin the tyres at high speed. This could  
•
cause them to explode and result in serious  
injury. Parts of the vehicle could also overheat  
and be damaged.  
In case of emergency 6-15  
Downloaded from manuals search engine  

Related Topics

Popular Owner Manuals