2006-2014 Nissan Qashqai SUV In case of emergency -> Changing flat tyre (Models with spare wheel, where fitted) User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

In case of emergency -> Changing flat tyre (Models with spare wheel, where fitted) for Your Nissan Qashqai SUV First Generation (2006-2014)

6. Turn off the engine.  
Place suitable blocks j1 in front of and behind the  
wheel diagonally opposite the flat tyre jA to prevent  
the vehicle from moving when it is on the jack.  
5–seater:  
1. Open the back door.  
7. Open the bonnet (for details, see “Bonnet  
release” in the “3. Pre-driving checks and  
adjustments” section) in order to:  
2. Remove the luggage compartment floor cover.  
Getting the tools and spare wheel  
3. Remove the retainer j1 by turning it anti-clock-  
Warn other traffic.  
The spare wheel, jack and tools are located inside  
the luggage compartment.  
•
•
wise.  
Signal to professional road assistance that  
you require assistance.  
4. Carefully remove and place the subwoofer  
(where fitted) j2 on the top right-hand side cor-  
ner of the luggage floor compartment (with the  
flat surface facing downwards).  
8. Have all passengers exit the vehicle and stand in  
a safe place, away from traffic and clear of the  
vehicle.  
NOTE  
CHANGING FLAT TYRE (Models with  
spare wheel, where fitted)  
Be careful not to drop the subwoofer.  
5. Remove the jack, tools and spare wheel.  
NCE307  
without subwoofer  
Type A  
Type B  
jA  
jB  
MCE0001DZ  
Blocking the wheels  
WARNING  
Make sure to block the appropriate wheel to pre-  
vent the vehicle from moving, which may cause  
personal injury.  
NCE312  
5–seater, with subwoofer (where fitted)  
In case of emergency 6-3  
Downloaded from manuals search engine  
7–seater:  
Removing wheel cover (where fitted)  
1. Open the back door.  
WARNING  
2. Remove both sides and centre floor boards j1 .  
Take care when removing the wheel cover as the  
cover may detach suddenly.  
3. Remove tonneau cover (where fitted) j2 and  
floor cover j3 . For details, see “Rear parcel shelf  
(where fitted)” in the “2. Instruments and  
controls” section.  
Remove the wheel cover as illustrated with a suit-  
able tool or carefully remove the wheel cover with  
both hands.  
4. Lower the head restraints and fold the third row  
seat. For details, see “Seats” in the “1. Safety —  
seats, seat belts and supplemental restraint  
system” section.  
Removing the wheel  
WARNING  
5. Release the seat from its locking latches jA by  
pulling up the two levers simultaneously on both  
sides j4 .  
Make sure to read the caution label attached  
to the jack body before use.  
•
Do not get under a vehicle that is supported  
only by a jack: Use vehicle support stands.  
•
6. Lift up the seat j5 and release the levers.  
7. Remove the jack, tools and spare wheel.  
Use only the jack that is provided with your  
vehicle. The jack is designed only for lifting  
your vehicle during a tyre change.  
•
Do not use the jack provided with your vehicle  
on other vehicles.  
•
Use the correct jack-up points. Never use any  
other part of the vehicle for jack support.  
•
Never lift the vehicle more than necessary.  
•
SCE0173AZ  
Never use blocks on or under the jack.  
•
Do not start or run the engine while the ve-  
hicle is on the jack. The vehicle may move  
suddenly, and this may cause an accident.  
•
NCE304  
7–seater  
6-4 In case of emergency  
Downloaded from manuals search engine  
Never allow passengers to stay in the vehicle  
while it is on the jack.  
Make sure to keep the lock key in the vehicle.  
Otherwise, wheels cannot be removed and the  
service cannot be performed.  
•
•
•
Remove all loads before lifting the vehicle with  
the jack.  
Make sure to block the wheel diagonally op-  
posite the flat tyre as described earlier in this  
section.  
CAUTION  
NCE143Z  
The jack should be used on firm, level ground.  
4. Loosen each wheel nut by one or two turns  
anticlockwise with the wheel wrench.  
NCE309  
5–seater  
Do not remove the wheel nuts until the tyre is  
off the ground.  
Models with wheel lock nuts (where fitted):  
If the wheel is equipped with a wheel lock nut,  
insert the wheel lock key j1 and loosen it as pre-  
viously described.  
NCE256Z  
Jack-up points  
The wheel lock nut can only be removed with the  
wheel lock key. A key number is necessary if you  
need to duplicate the wheel lock key.  
1. Place the jack directly under the jack-up point as  
illustrated so that the top of the jack contacts the  
vehicle at the jack-up point.  
NCE308  
Record the key number as shown on the key  
code card on the “Security information” page at  
the end of this manual and keep it in a safe place,  
not in the vehicle. If you loose the wheel lock key,  
see your NISSAN dealer for a duplicate with the  
original wheel lock key code.  
7–seater  
2. Align the centre of both the jack head and the  
notches at the jack-up point as shown.  
5. To lift the vehicle, securely hold and turn the  
handle clockwise as shown.  
3. Fit the groove of the jack head between the two  
notches as shown.  
6. Carefully raise the vehicle until the tyre clears the  
ground.  
7. Remove the wheel nuts, then remove the wheel  
with the flat tyre.  
In case of emergency 6-5  
Downloaded from manuals search engine  
CAUTION  
Tighten  
Wheel nut tightening torque:  
113 N•m (12 kg-m, 83 ft-lb)  
jA  
jB  
jC  
The wheel is heavy. Be sure that your feet are  
clear of the wheel and use gloves as necessary  
to avoid injury.  
Loosen  
Bevelled face  
WARNING  
1. Clean any mud or dirt from the surface between  
the wheel and the hub.  
Retighten the wheel nuts after the vehicle has  
been driven for 1,000 km (600 miles) (also in  
cases of a flat tyre, etc.).  
Installing the wheel  
2. Carefully fit the wheel and tighten the wheel nuts  
with your fingers. Check that all the wheel nuts  
contact the wheel surface horizontally and on the  
bevelled side.  
WARNING  
The wheel nuts must be kept tightened to specifica-  
tion at all times. It is recommended that the wheel  
nuts be tightened to specification at each mainte-  
nance interval.  
The temporary use spare tyre is designed for  
emergency use. See “Spare tyre” earlier in  
this section.  
•
Models with wheel lock nut (where fitted):  
Never use wheel nuts other than those pro-  
•
Adjust the tyre pressure to the COLD pressure.  
Insert the wheel lock key into the wheel lock nut  
and tighten into the wheel finger tight.  
vided with your vehicle. Incorrect wheel nuts  
or improperly tightened wheel nuts may cause  
the wheel to become loose or come off. This  
could cause an accident.  
COLD pressure is the tyre pressure as measured  
after the vehicle has been parked for three hours or  
more or driven for less than 1.6 km (1 mile).  
3. With the wheel wrench, tighten the wheel nuts  
alternately and evenly in the sequence as illus-  
trated (j1 - j5 ) until they are tight.  
Never use oil or grease on the wheel studs or  
nuts. This may cause the wheel nuts to be-  
come loose.  
COLD tyre pressures are shown on the tyre placard  
affixed to the driver’s side centre pillar.  
•
4. Lower the vehicle slowly until the tyre touches  
the ground.  
Stowing the wheel and tools  
5. Tighten the wheel nuts securely using the wheel  
wrench in the sequence as illustrated.  
WARNING  
6. Lower the vehicle completely.  
7. Install the wheel cover (where fitted).  
NOTE  
Always make sure that the wheel, subwoofer  
(where fitted), jack and tools are properly stored  
after each use. Such items can become danger-  
ous projectiles in an accident or sudden stop.  
Before installation, align NISSAN logo (centre  
cap) with the wheel nuts/or perpendicular to  
valve hole (where fitted), to correctly align to  
the centre.  
5–seater  
1. Securely store the wheel with the flat tyre, the  
jack and the tools in the specified storage areas.  
See “Getting the tools and spare wheel” earlier  
in this section(for 5–seater).  
NCE287Z  
As soon as possible, tighten the wheel nuts to  
the specified torque with a torque wrench.  
6-6 In case of emergency  
Downloaded from manuals search engine  
2. Store the subwoofer (where fitted) as it was origi-  
nally installed.  
normal wheel nuts. For details, see “Chang-  
ing flat tyre (Models with spare wheel, where  
fitted)” earlier in this section.  
Wheel lock nuts (where fitted)  
In order to prevent theft, the specially designed  
wheel lock nut is installed to each wheel. The wheel  
lock nut cannot be removed with the commonly used  
tools.  
3. Install the retainer and replace the floor cover.  
NOTE  
The wheel lock nut has an individual code.  
•
A wheel lock key with other than the indi-  
vidual code cannot remove the wheel lock  
nut. If you lose the wheel lock key, contact  
a NISSAN dealer for a duplicate with the  
original wheel lock key code.  
When removing tyres, use the lock key provided  
with your vehicle.  
Record the key number as shown on the  
•
key code card on the “Security informa-  
tion” page at the end of this manual and  
keep it in a safe place, not in the vehicle.  
NCE306  
7–seater  
When you ask for a service at a NISSAN  
•
dealer or qualified workshop, make sure  
to keep the lock key in the vehicle. Other-  
wise, wheels cannot be removed and the  
service cannot be performed.  
1. Store the tools in the specified areas.  
NCE143Z  
2. Firmly pull down the third row seat and make  
sure it locks into the locking latches on both sides  
under the seat.  
Removing the wheel lock nut:  
REPAIRING FLAT TYRE (Models with  
emergency tyre puncture repair kit,  
where fitted)  
1. Insert the wheel lock key j1 to the wheel lock  
3. Place the seatback of the third row seat in the  
upright position j1 . For details, see “Folding 3rd  
row (7-seater)” in the “1. Safety — seats, seat  
belts and supplemental restraint system” section.  
nut.  
2. To remove the wheel lock nut, turn the wheel  
lock key anticlockwise using the wheel wrench.  
The emergency tyre puncture repair kit is supplied  
with the vehicle instead of a spare tyre. This repair  
kit must be used for temporarily fixing a minor tyre  
puncture. After using the repair kit, see a NISSAN  
dealer or qualified workshop as soon as possible for  
tyre inspection and repair/replacement.  
CAUTION  
4. Store the wheel with flat tyre vertically in the boot  
j2 .  
Do not use a power tool to remove the wheel  
lock nuts.  
•
5. Store the other items in following order:  
When installing the wheel, tighten the wheel  
lock nuts to the same tightening torque as the  
Tonneau cover (where fitted) j3 → Floor cover  
j4 → Centre floor board and the two side floor  
boards j5 .  
•
In case of emergency 6-7  
Downloaded from manuals search engine  

Related Topics

Popular Owner Manuals