2006-2014 Nissan Qashqai SUV Safety ? seats, seat belts and supplemental restraint system -> Rear seat(s) User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Safety ? seats, seat belts and supplemental restraint system -> Rear seat(s) for Your Nissan Qashqai SUV First Generation (2006-2014)

CAUTION  
is folded past the vertical position. If the lever is  
released early the seat will go into Easy entry  
mode, see “Easy entry to the 3rd row (7-seater)”  
later in this section.  
REAR SEAT(S)  
Always ensure that the seat belt is not trapped in  
the release lever or any other vehicle part.  
3. Fold the seat forward.  
To return the 2nd row outer seat to the seating posi-  
tion, pull and hold the lever j2 up to push the  
seatback up until it locks into position. Pull the lever  
again to set the angle of the seatback as desired.  
Pull the head restraint into the correct position for  
the occupant using the seat.  
NPA928Z  
5–seater  
NPA977  
Folding (5-seater)  
The luggage compartment loading capacity can be  
increased by folding the rear seats forward.  
Adjustment 2nd row (7-seater)  
Pull the lever j1 up while you slide the seat forward  
or backward to the desired position. Release the  
lever to lock the seat in position. Rock the seat to  
check the slides have locked. Pull the lever j2 to  
set the angle of the seatback as desired.  
To fold the seat:  
1. Insert the side seat belt tongue into the slot lo-  
cated on the rear door pillar j1 as illustrated.  
2. Release the seatback lock by pulling on the latch  
NPA978  
j2 .  
Folding 2nd row (7-seater)  
To fold the outer seats:  
3. Fold the seat forward j3 .  
To fold the centre seat:  
To return the seat to an upright position:  
1. Push the release button of the head restraint and  
push the head restraint down. See “Head  
restraints” later in this section.  
1. Push the release button of the head restraint and  
push the head restraint down. See “Head  
restraints” later in this section.  
1. Make sure the seat belt is clear of the seat latch  
mechanism.  
2. Lift the seatback up and push firmly onto the  
latch.  
2. Make sure the seat belt tongue of the centre seat  
is in the store position, see “Fastening the seat  
belts” later in this section.  
2. Release the seatback lock by pulling the lever j2  
up. The lever must be held up until the seatback  
3. If the red lock tab is visible then the seat has not  
latched properly — release and then re-latch the  
seat.  
3. Release the seatback lock by pulling the strap  
j1 .  
Safety — seats, seat belts and supplemental restraint system 1-3  
Downloaded from manuals search engine  
4. Fold the seatback forward.  
The seat will lock into position. Rock the seat to  
confirm it is locked in position. Adjust the seat if  
necessary, see “Adjustment 2nd row (7-seater)”  
earlier in this section.  
4. Fold the seatback forward.  
To return the 2nd row centre seat to its seating posi-  
tion, pull the strap to push the seatback up until it  
latches into position. Pull the strap again to set the  
angle of the seatback as desired. Pull the head re-  
straint into the correct position for the occupant us-  
ing the seat.  
To return the 3rd row seat to its seating position,  
pull the strap to pull the seatback up until it locks  
into position. Pull the strap again to set the angle of  
the seatback as desired. Pull the head restraint into  
the highest position.  
NOTE  
Instead of using the latch, it is also possible to  
pull the lever j2 up. Pull the seatback past  
the vertical position and release the lever. The  
seat will slide forward.  
•
The 2nd row centre seat slides forward to-  
gether with the right outer seat.  
•
NPA981  
Easy entry to the 3rd row (7-seater)  
1. The seating positions on the 2nd row can be slid  
forward for easy entry or exit from the 3rd row  
seat. To slide the 2nd row bench seat, lift up the  
latch j1 located on the upper corner of the  
seatback and pull the seatback forward. When  
pulling the seatback, the seat bench then slides  
forward.  
NPA979  
Folding 3rd row (7-seater)  
1. Push the release button of the head restraint and  
push the head restraint down. See “Head  
restraints” later in this section.  
2. To return the seat to its seating position, push  
the seat bench rearward then lift the seatback.  
2. Attach the side seat belt tongue to the stowage  
hook located on the rear pillar j1 as illustrated.  
3. Release the seatback lock by pulling the strap  
j2 .  
1-4 Safety — seats, seat belts and supplemental restraint system  
Downloaded from manuals search engine  

Related Topics

Popular Owner Manuals