2006-2014 Nissan Qashqai SUV Safety ? seats, seat belts and supplemental restraint system -> Seats User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Safety ? seats, seat belts and supplemental restraint system -> Seats for Your Nissan Qashqai SUV First Generation (2006-2014)

SEATS  
Closely supervise children when they are  
around the vehicle to prevent them from play-  
ing and being locked in the luggage compart-  
ment where they could be seriously injured.  
Keep the vehicle locked with the rear seat-  
back securely latched when not in use, and  
prevent children from having access to the  
vehicle’s keys.  
•
FRONT SEATS  
WARNING  
Do not adjust the driver’s seat while driving.  
The seat may move suddenly and could cause  
loss of control of the vehicle.  
•
After adjustment, gently rock in the seat to  
make sure it is securely locked.  
•
•
The seatback should not be reclined any more  
than needed for comfort. Seat belts are most  
effective when the passenger sits well back  
and upright in the seat. If the seatback is re-  
clined, the risk of sliding under the lap belt  
and being injured is increased.  
When returning the seatbacks to the upright  
position, be certain that they are completely  
secured in the latched position. If they are not  
completely secured, passengers may be in-  
jured in an accident or sudden stop. When  
operating the seatback release always rock  
the seatback afterward to check that it is  
locked.  
•
When the vehicle is being used to carry cargo,  
properly secure all cargo to help prevent it  
from sliding or shifting. Do not place cargo  
higher than the seatbacks. In a sudden stop  
or collision, unsecured cargo could cause per-  
sonal injury.  
•
•
NDI1100  
Adjustment  
Slide the seat forward and backward  
j1  
j2  
j3  
j4  
Never allow anyone to ride in the luggage area  
or on the rear seat when it is in the folded-  
down position. Use of these areas by passen-  
gers without proper restraints could result in  
serious injury in an accident or sudden stop.  
Reclining the seatback  
Lift or lower the seat (driver’s side only)  
Lumbar support (where fitted)  
1-2 Safety — seats, seat belts and supplemental restraint system  
Downloaded from manuals search engine  
CAUTION  
is folded past the vertical position. If the lever is  
released early the seat will go into Easy entry  
mode, see “Easy entry to the 3rd row (7-seater)”  
later in this section.  
REAR SEAT(S)  
Always ensure that the seat belt is not trapped in  
the release lever or any other vehicle part.  
3. Fold the seat forward.  
To return the 2nd row outer seat to the seating posi-  
tion, pull and hold the lever j2 up to push the  
seatback up until it locks into position. Pull the lever  
again to set the angle of the seatback as desired.  
Pull the head restraint into the correct position for  
the occupant using the seat.  
NPA928Z  
5–seater  
NPA977  
Folding (5-seater)  
The luggage compartment loading capacity can be  
increased by folding the rear seats forward.  
Adjustment 2nd row (7-seater)  
Pull the lever j1 up while you slide the seat forward  
or backward to the desired position. Release the  
lever to lock the seat in position. Rock the seat to  
check the slides have locked. Pull the lever j2 to  
set the angle of the seatback as desired.  
To fold the seat:  
1. Insert the side seat belt tongue into the slot lo-  
cated on the rear door pillar j1 as illustrated.  
2. Release the seatback lock by pulling on the latch  
NPA978  
j2 .  
Folding 2nd row (7-seater)  
To fold the outer seats:  
3. Fold the seat forward j3 .  
To fold the centre seat:  
To return the seat to an upright position:  
1. Push the release button of the head restraint and  
push the head restraint down. See “Head  
restraints” later in this section.  
1. Push the release button of the head restraint and  
push the head restraint down. See “Head  
restraints” later in this section.  
1. Make sure the seat belt is clear of the seat latch  
mechanism.  
2. Lift the seatback up and push firmly onto the  
latch.  
2. Make sure the seat belt tongue of the centre seat  
is in the store position, see “Fastening the seat  
belts” later in this section.  
2. Release the seatback lock by pulling the lever j2  
up. The lever must be held up until the seatback  
3. If the red lock tab is visible then the seat has not  
latched properly — release and then re-latch the  
seat.  
3. Release the seatback lock by pulling the strap  
j1 .  
Safety — seats, seat belts and supplemental restraint system 1-3  
Downloaded from manuals search engine  
4. Fold the seatback forward.  
The seat will lock into position. Rock the seat to  
confirm it is locked in position. Adjust the seat if  
necessary, see “Adjustment 2nd row (7-seater)”  
earlier in this section.  
4. Fold the seatback forward.  
To return the 2nd row centre seat to its seating posi-  
tion, pull the strap to push the seatback up until it  
latches into position. Pull the strap again to set the  
angle of the seatback as desired. Pull the head re-  
straint into the correct position for the occupant us-  
ing the seat.  
To return the 3rd row seat to its seating position,  
pull the strap to pull the seatback up until it locks  
into position. Pull the strap again to set the angle of  
the seatback as desired. Pull the head restraint into  
the highest position.  
NOTE  
Instead of using the latch, it is also possible to  
pull the lever j2 up. Pull the seatback past  
the vertical position and release the lever. The  
seat will slide forward.  
•
The 2nd row centre seat slides forward to-  
gether with the right outer seat.  
•
NPA981  
Easy entry to the 3rd row (7-seater)  
1. The seating positions on the 2nd row can be slid  
forward for easy entry or exit from the 3rd row  
seat. To slide the 2nd row bench seat, lift up the  
latch j1 located on the upper corner of the  
seatback and pull the seatback forward. When  
pulling the seatback, the seat bench then slides  
forward.  
NPA979  
Folding 3rd row (7-seater)  
1. Push the release button of the head restraint and  
push the head restraint down. See “Head  
restraints” later in this section.  
2. To return the seat to its seating position, push  
the seat bench rearward then lift the seatback.  
2. Attach the side seat belt tongue to the stowage  
hook located on the rear pillar j1 as illustrated.  
3. Release the seatback lock by pulling the strap  
j2 .  
1-4 Safety — seats, seat belts and supplemental restraint system  
Downloaded from manuals search engine  
3. Rear armrest (7–seater) jC  
ARMRESTS (where fitted)  
Pull the strap j1 at the centre seat bench and lay  
the centre seatback/armrest horizontally.  
HEAD RESTRAINTS  
WARNING  
Do not drive and/or ride in the vehicle with  
the head restraint removed. This can be dan-  
gerous.  
•
NPA925Z  
Front and Rear (where fitted) seat head restraints  
Head restraints should be adjusted properly  
•
as they may provide significant protection  
against injury in an accident. Check the height  
after someone else uses the seat.  
Adjustment  
1. Pull up the head restraint to raise to the proper  
position.  
If the head restraints are removed for any rea-  
•
2. Push in the lock knob as illustrated to lower the  
head restraint to the proper position.  
son, they should be securely stored to pre-  
vent them from causing injury to passengers  
or damage to the vehicle in case of sudden  
braking or an accident.  
Adjust the head restraint so that the centre is level  
with your ears.  
7–seater: The head restraints of the 3rd row  
should always be put into the highest position  
when the seat is occupied.  
•
NPA980  
1. Front armrest jA  
Slide the console box lid forwards to use as an  
armrest.  
2. Rear armrest (5–seater) jB  
Pull the armrest of the rear seat and lay it horizon-  
tally.  
Safety — seats, seat belts and supplemental restraint system 1-5  
Downloaded from manuals search engine  
SEAT BELTS  
ing its backward movement and by helping to ab-  
sorb some of the forces that may lead to whiplash  
type injuries.  
ACTIVE HEAD RESTRAINTS (front  
seats)  
Active head restraints are effective for collisions at  
low to medium speeds in which it is said that whip-  
lash injury occurs most.  
Active head restraints operate only in certain rear-  
end collisions. After the collision, the head restraints  
return to their original positions.  
NPA1051  
Properly adjust the active head restraints as de-  
scribed in the previous section.  
SPA1025Z  
WARNING  
7–seater: Seat belts for 3rd row seats are not  
part of the seat belt warning monitoring system.  
WARNING  
Always adjust the head restraints properly as  
specified in the previous section. Failure to do  
so can reduce the effectiveness of the active  
head restraint.  
•
•
•
SEAT BELT WARNINGS  
jA Driver and front passenger  
The seat belt warning lights, located in the instru-  
ment panel jA , will light up if the driver and/or front  
passenger seat belts have not been fastened. See  
“Warning/indicator lights and audible reminders” in  
the “2. Instruments and controls” section for further  
details.  
Active head restraints are designed to supple-  
ment other safety systems. Always wear seat  
belts. No system can prevent all injuries in an  
accident.  
Do not attach anything to the head restraint  
stalks. Doing so could impair the active head  
restraint’s function.  
jB Rear passengers  
The rear passenger seat belt warning is shown in  
the vehicle information display jB . See “Vehicle in-  
formation display” in the “2. Instruments and  
controls” section.  
The head restraint moves forward utilising the force  
that the seatback receives from the occupant in a  
rear-end collision. The movement of the head re-  
straint helps support the occupant’s head by reduc-  
The seat belt warning alerts the driver and/or front  
passenger if a (rear) seat belt is not securely fas-  
1-6 Safety — seats, seat belts and supplemental restraint system  
Downloaded from manuals search engine  

Related Topics

Popular Owner Manuals