2017-2023 Peugeot 5008 SUV Ease of use and comfort User Manual

MY CAR USER MANUAL

Ease of use and comfort for Your Peugeot 5008 SUV Second Generation (2017-2023)

Access  
► To close the sunroof or the blind, use the part  
of the button located towards the front.  
Reinitialisation  
Following reconnection of the battery or in the  
event of a fault or jerky movement of the sunroof  
or blind, reinitialisation is required.  
► Check that nothing is interfering with the  
sunroof or blind and that the seals are clean.  
► With the ignition on, fully close the sunroof  
and blind.  
2
Operation of buttons  
► Pressing a button beyond its point of  
resistance directly opens or closes the sunroof  
fully.  
► Pressing the button again stops the current  
movement.  
► Press and hold the front part of button B, until  
the sunroof and blind move slightly, then hold for  
a further 1 second before releasing.  
► Wait 2 seconds and then press and hold the  
front part of button B. The blind and the sunroof  
will open and close, one after the other. When  
both are completely closed again, hold for a  
further 2 seconds and release.  
► When holding a button (without going  
beyond the point of resistance), the movement  
of the sunroof or blind stops when this button is  
released.  
► When the sunroof is closed: pressing once  
without passing the point of resistance moves it  
to a partially open position.  
► When the sunroof is partially open: pressing  
once without passing the point of resistance  
opens or closes it fully.  
If there is an operating fault, restart the  
whole procedure.  
The roof and windows, then the blind,  
can be closed by holding down the door  
locking control. The operation stops as soon  
as the locking control is released.  
Closing of the blind is limited by the  
position of the sunroof: the blind cannot  
go further than the front of the mobile glass.  
During simultaneous movements of the  
sunroof and blind, the blind automatically  
stops or resumes movement depending on  
the position of the sunroof.  
43  
Ease of use and comfort  
The distance between your knees and the  
dashboard should be at least 10 cm, for easy  
access to the dashboard controls.  
Adjust the backrest angle to as vertical a position  
as possible; never tilt it more than 25°.  
Adjust the head restraint so that its upper edge is  
level with the top of your head.  
Adjust the length of the seat cushion to support  
your thighs.  
Adjust the lumbar support so that it conforms to  
the shape of your spine.  
Passenger’s side  
Driving position  
Correct seating position  
Adopting a good driving position helps improve  
your comfort and protection.  
It also optimises interior and exterior visibility as  
well as access to controls.  
Whether or not the vehicle has certain seat  
adjustments described in this section depends  
on the trim level and country of sale.  
Adjust the steering wheel so that it is at least 25  
cm from your sternum and you can hold it with  
your arms slightly bent.  
The steering wheel should not hide the  
instrument panel.  
Driver’s side  
Sit fully back in the seat with your pelvis, back  
and shoulders in contact with the seat backrest.  
Adjust the longitudinal position of the seat so that  
you are at a distance of at least 25 cm from the  
dashboard.  
As a safety precaution, adjust the seats  
only when the vehicle is stationary.  
Adjust the head restraint so that its upper edge is  
level with the top of your head.  
Before moving off  
Adjust the interior and exterior door mirrors to  
reduce blind spots.  
If your vehicle has electric seats, the  
ignition must be on to adjust them.  
Fasten your seat belt: place the diagonal belt in  
the middle of your shoulder and adjust the lap  
belt so that it is tightened across your pelvis.  
Ensure that all passengers have fastened their  
seat belts correctly.  
Sit fully back in the seat with your pelvis, back  
and shoulders in contact with the seat backrest.  
Adjust the seat cushion height so that your eyes  
are level with the centre of the windscreen.  
The head room (from the roof) should be at least  
10 cm.  
Adjust the longitudinal position of the seat so  
that you can fully depress the pedals with legs  
slightly flexed.  
If your vehicle has electric door mirrors,  
the ignition must be on to adjust them.  
44  
Ease of use and comfort  
When driving  
Manually-adjusted seats  
5. Lumbar support adjustment  
3
(only on the driver's seat)  
Maintain a good driving position and hold the  
steering wheel with both hands at the 'quarter to  
three' position, so that you can easily and quickly  
reach the controls behind and near the steering  
wheel.  
► Turn the knob forwards or backwards  
to increase or decrease the level of lumbar  
support.  
‘AGR’ certified seats  
Additional adjustments  
Never adjust the seats or steering wheel  
when driving.  
Always keep your feet on the floor.  
Front seats  
Before moving the seat backwards,  
ensure that there is no person or object  
that might prevent the full travel of the seat.  
There is a risk of trapping or pinching  
passengers if present in the rear seats or of  
jamming the seat if large objects are placed  
on the floor behind the seat.  
1. Longitudinal adjustment of the seat position  
► Raise the control bar and slide the seat  
forwards or backwards.  
1. Seat cushion length adjustment  
► Pull the handle forwards to release the  
cushion, then move the front part of the seat  
cushion forwards or backwards.  
2. Seat cushion angle electric adjustment  
► Press and hold the front or rear of the  
button to raise or lower the front part of the  
seat cushion.  
► Release the bar to lock the seat in  
position in one of the notches.  
2. Seat cushion height adjustment  
► Raise or lower the control as many times  
as needed to obtain the desired height.  
3. Seat backrest angle adjustment  
► Turn the knob forwards or backwards to  
recline the backrest to the desired angle.  
or  
► For a passenger seat that can be placed  
in the table position, pull the handle and  
guide the backrest forwards or backwards.  
4. Head restraint height adjustment  
Refer to the corresponding section.  
45  
Ease of use and comfort  
Folding the backrest  
Front head restraints  
3. Lumbar support electric adjustment  
The control allows independent adjustment of  
the depth and vertical position of the lumbar  
support.  
Adjusting the height  
► Press and hold the front or rear of the  
control to increase or reduce the lumbar  
support.  
► Press and hold the top or bottom of the  
control to raise or lower the lumbar support  
area.  
Placing the passenger seat  
in the table position  
► Pull the control fully up to release the  
backrest.  
The backrest of the passenger seat can be fully  
folded forwards and secured in this position.  
This function, when associated with folding  
of the backrest of the rear seats, helps with  
transporting long and bulky objects.  
First steps:  
► Lower the head restraint.  
► Fold up the “aircraft” type table (depending  
on version).  
► Move the seat backwards to allow space for  
the head restraint.  
► Adjust the seat to the lowest position.  
► Check that there is nothing that might  
interfere with folding of the backrest (seat belt,  
child seat, items of clothing, bags, etc.).  
► Tip the backrest fully forward.  
► Upward: pull the head restraint up to the  
desired position; the head restraint can be felt to  
click into position.  
► Downward: press lug A to lower the head  
restraint.  
In this position, the backrest can support  
a maximum load of 30 kg.  
When sharp deceleration occurs, objects  
placed on the folded backrest can turn into  
projectiles.  
The head restraint is correctly adjusted  
when its upper edge is level with the top  
of the passenger’s head.  
Returning the backrest to the normal  
position  
► Pull the control fully up to release the  
backrest.  
► Raise the backrest and guide it back until it  
latches into place.  
► Check that the backrest has engaged  
correctly.  
Removing a head restraint  
► Pull the head restraint fully up.  
► Press lug A to release the head restraint and  
raise it fully.  
► Stow the head restraint securely.  
Deactivation of the front passenger  
airbag is recommended.  
46  
Ease of use and comfort  
Refitting a head restraint  
5. Lumbar support adjustment  
3
► Insert the head restraint rods into the guides  
in the corresponding seat backrest.  
► Push the head restraint down as far as it will  
go.  
► Press the lug A to release the head restraint  
and push it down.  
The control allows independent adjustment of  
the depth and vertical position of the lumbar  
support.  
► Press and hold the front or rear of the  
control to increase or reduce the lumbar  
support.  
► Adjust the height of the head restraint.  
► Press and hold the top or bottom of the  
control to raise or lower the lumbar support  
area.  
Never drive with the head restraints  
removed; they should be in place and  
adjusted for the occupant of the seat.  
Memorising driving  
positions  
Associated with the electrically-adjusted driver’s  
seat, this function allows two driving positions  
to be memorised, to make these adjustments  
easier if there are frequent driver changes.  
It takes account of the electric adjustments of the  
seat and the door mirrors.  
Electrically-adjusted driver's  
seat  
1. Seat cushion height and angle adjustment/  
Longitudinal adjustment of the seat position  
► Raise or lower the front of the control to  
obtain the desired seat cushion angle.  
► Raise or lower the rear of the control to  
raise or lower the seat cushion.  
To carry out these electric adjustments,  
switch on the ignition or start the engine  
if the vehicle has gone into energy economy  
mode.  
► Slide the control forwards or backwards to  
move the seat forwards or backwards.  
2. Seat backrest angle adjustment  
► Turn the control forwards or backwards to  
recline the backrest to the desired angle.  
3. Head restraint height adjustment  
Refer to the corresponding section.  
These electric adjustments are accessible  
about 1 minute after opening the driver's door.  
They are deactivated about 1 minute after  
switching the ignition off.  
4. Seat cushion length adjustment  
► Pull the handle forwards to release the  
cushion, then move the front part of the seat  
cushion forwards or backwards.  
Using buttons M / 1 / 2  
47  
Ease of use and comfort  
► Enter the vehicle and switch the ignition on.  
► Adjust your seat and the door mirrors.  
► Press button M, then press button 1 or 2  
within 4 seconds.  
The function is active only with the engine  
running.  
– do not kneel or stand on the seat,  
– do not spill liquids onto the seat,  
– never use the heating function if the seat  
is wet.  
On/Off  
An audible signal confirms the memorisation.  
Memorising a new position cancels the previous  
position.  
► Press the button corresponding to your seat.  
► Each press changes the heating level; the  
corresponding number of indicator lamps come  
on.  
► To stop heating, press the button again until  
all the indicator lamps are off.  
Multipoint massage  
System with a choice of type of massage and  
adjustment of its intensity.  
Recalling a stored position  
This system operates with the engine running, as  
well as in STOP mode of the Stop & Start.  
The massage settings are adjusted via the touch  
screen.  
Ignition on or engine running  
► Press button 1 or 2 to recall the  
corresponding position.  
An audible signal sounds when the adjustment  
is finished.  
You can interrupt the current movement by  
pressing button M, 1 or 2 or by using one of the  
seat adjustment controls.  
A stored position cannot be recalled while  
driving.  
The system status is memorised when the  
ignition is switched off.  
Do not use the function when the seat  
is not occupied.  
Reduce the heating intensity as soon as  
possible.  
When the seat and passenger compartment  
have reached a satisfactory temperature,  
switch the function off; reducing electricity  
consumption in turn decreases fuel  
consumption.  
From the front seat:  
► Press this button; its green indicator  
lamp comes on.  
The settings page is displayed on the touch  
screen with the last memorised settings.  
If the settings suit you and you make no  
changes, the display returns to its previous state,  
and the function activates immediately.  
Seats must be adjusted one after another,  
starting with the driver's seat.  
Recalling stored positions is deactivated 45  
seconds after switching off the ignition.  
Heated seats  
Prolonged use of the heated seats is not  
recommended for those with sensitive  
skin.  
There is a risk of burns for people whose  
perception of heat is impaired (illness, taking  
medication, etc.).  
To keep the heated pad intact and to prevent  
a short circuit:  
– do not place sharp or heavy objects on the  
seat,  
To modify the settings:  
► Begin with the driver’s seat.  
► Select a massage intensity from the three  
levels offered: "1" (Low), "2" (Normal) or "3"  
(High).  
► Select another type of massage from those  
offered.  
► Wait for the driver's seat settings page to  
disappear.  
48  
Ease of use and comfort  
► Next, proceed with the passenger's seat in  
the same way.  
Mirrors  
3
► Move control A to the right or to the left to  
select the corresponding mirror.  
► Move control B in any of the four directions  
to adjust.  
The changes are applied immediately.  
Once activated, the system starts a one hour  
massage cycle, made up of sequences of 6  
minutes of massage followed by 3 minutes at  
rest.  
Door mirrors  
As a safety measure, the mirrors should  
► Return control A to its central position.  
be adjusted to reduce the "blind spots".  
The objects that you see in the mirrors are  
in fact closer than they appear. Take this  
into account in order to correctly judge the  
distance of vehicles approaching from behind.  
Manual folding  
The mirrors can be folded manually (parking  
obstruction, narrow garage, etc.).  
The system automatically stops at the end of the  
cycle; the indicator lamp for the button goes off.  
► Turn the mirror towards the vehicle.  
Steering wheel  
adjustment  
Demisting/Defrosting  
Electric folding  
Depending on equipment, the mirrors can be  
folded electrically, when the vehicle is parked.  
If the vehicle is so equipped, demisting/  
defrosting of the heated door mirrors is  
performed when the heated rear screen is  
switched on.  
For more information on Rear screen  
demisting/defrosting, refer to the  
corresponding section.  
► From the inside, with the  
ignition on, place control A in the  
central position.  
► Pull control A backwards.  
► Lock the vehicle from the outside.  
► When stationary, pull the control to release  
the steering wheel.  
Adjustment  
Electric unfolding  
► Adjust the height and reach to suit your  
driving position.  
► Push the control lever to lock the steering  
wheel.  
► From outside: unlock the vehicle.  
► From inside: with the ignition on, place  
control A in the central position and then pull it  
rearwards.  
As a safety measure, these adjustments  
must only be carried out with the vehicle  
stationary.  
Depending on version, the automatic  
door mirror folding/unfolding function is  
49  
Ease of use and comfort  
configured via the Driving / Vehicle touch  
screen menu.  
► Pull the lever to change to the anti-dazzle  
"night” position.  
Rear head restraints  
Otherwise, this setting can be carried out at a  
PEUGEOT dealer or a qualified workshop.  
► Push the lever to change to the normal "day"  
position.  
Adjustment  
► Set the mirror to the normal “day” position.  
Automatic tilting in reverse gear  
Depending on version, this function allows to  
automatically tilt the mirrors downwards to assist  
with parking manoeuvres in reverse gear.  
With the engine running, on engaging reverse  
gear, the mirror glasses tilt downwards.  
They return to their initial position:  
– A few seconds after coming out of reverse  
gear.  
– Once the vehicle speed exceeds 6 mph  
(10 km/h).  
– When the engine is switched off.  
This function is set via the Driving/  
Vehicle touch screen menu.  
Automatic "electrochrome" model  
This system automatically and progressively  
transitions between day and night modes, using  
a sensor that measures the light entering from  
the rear of the vehicle.  
To ensure optimum visibility during your  
manoeuvres, the mirror lightens  
automatically when reverse gear is engaged.  
Interior rear view mirror  
Manual model  
Day/night position  
High position (use):  
► Pull the head restraint fully up.  
Low position (stowing; when the seats are not  
in use):  
► Press the lugs A to release the head restraint  
and push it down.  
50  
Ease of use and comfort  
The folding of the backrest is  
accompanied by a slight lowering of the  
corresponding cushion.  
To obtain a flat surface, it is necessary to  
place the adjustable boot floor in the high  
position.  
When the backrest is released, the red  
indicator in the release grip is visible.  
The rear head restraints can be removed.  
Folding the backrests  
3
Removing a head restraint  
► Pull the head restraint fully up.  
► Press the lugs A to release the head restraint  
and remove it completely.  
► Store the head restraint.  
Refitting a head restraint  
► Insert the head restraint rods into the guides  
in the corresponding seat backrest.  
► Push the head restraint down as far as it will  
go.  
Folding from the passenger  
compartment  
► Press the lugs A to release the head restraint  
and push it down.  
Each section of the backrest has two release  
controls:  
– a grip 1 on the outer edge of the backrest,  
– a lever 2 on the boot side trim.  
Never drive with passengers seated at  
the rear when the head restraints are  
removed; the head restraints should be in  
place and in the high position.  
Manoeuvring the seat backrests should  
only be done when the vehicle is  
stationary.  
The head restraint for the central  
seat and those for the side seats  
are not interchangeable.  
First steps:  
► Lower the head restraints.  
► Lift up the rear armrest.  
► Press the backrest release grip 1.  
► Guide the backrest 3 down to the horizontal  
position.  
► If necessary, move the front seats forward.  
► Check that no person or object will interfere  
with folding down the backrests (clothing,  
luggage, etc.).  
Rear bench seat  
► Check that the outer seat belts are lying flat  
on the backrests.  
► Check that the centre seat belt buckle is  
stored in its housing.  
Bench seat with fixed cushions and split folding  
backrests (2/3-1/3) to adapt the boot load space.  
51  
Ease of use and comfort  
Folding from the boot  
► Put the backrest 3 in the upright position and  
push it firmly to latch it home.  
► Check that the red indicator is no longer  
visible in the release grip 1.  
► Ensure that the outer seat belts were not  
trapped during the operation.  
Please note: an incorrectly latched  
backrest compromises the safety of  
passengers in the event of sudden braking or  
an accident.  
The contents of the boot may be thrown  
forward - risk of serious injury!  
► Pull the backrest release lever 2 towards you.  
The backrest 3 folds fully onto the cushion.  
Second row seats  
Repositioning the backrests  
First check that the outer seat belts are  
lying vertically flat alongside the backrest  
latching rings.  
A. Longitudinal adjustment  
B. Seat backrest angle adjustment and folding  
C. Folding the backrest from behind and  
emergency exit for third row passengers  
D. Access to third row seats  
Seat adjustment  
The three second row seats are independent  
and of the same width. Their backrests can be  
folded to adapt the boot load space.  
52  
Ease of use and comfort  
Before and while performing the  
operation on the seats, check that the  
passengers, children in particular, keep their  
hands and their feet far from the moving parts  
of the seats (hinges, slides, etc.) - risk of  
serious injury!  
Longitudinal adjustment  
► Lift control handle B1 and guide the backrest  
backwards or forwards, raising yourself slightly  
if needed.  
► Release the handle and ensure the backrest  
is properly locked on one of the positions offered.  
Central seat  
3
► Lift control strap B2 and guide the backrest  
backwards or forwards, raising yourself slightly  
if needed.  
Folding from the outside  
► Release the strap and ensure the backrest is  
properly locked on one of the positions offered.  
Flat floor  
► Raise control bar A and slide the seat  
forwards or backwards.  
► Release the bar to lock the seat in position in  
one of the notches.  
Seat backrest angle adjustment  
► Pull handle B1 or strap B2 until the backrest  
is fully folded.  
► Release the control.  
► Gently push the backrest forwards so that  
the backrest tilts until it is folded onto the seat  
cushion.  
Folding the backrests  
► Check that the "aircraft" type tables of the  
front seats are properly folded.  
► Place the second row seats in the maximum  
rear position.  
Side seats  
53  
Ease of use and comfort  
Folding from the boot  
► Straighten the backrest until it locks.  
Before deploying the continuity panels,  
check that the 2nd row seats are pulled as  
far back as possible.  
Before performing any operations on the  
rear seats, to avoid damage to the seat  
belts, check that the lateral seat belts are  
properly tensioned. The central seat belt must  
be stored in the headlining.  
Accessing third row seats  
The third row seats are accessed via the second  
row side seats.  
Continuity panels  
When loading, for example, or from the third row  
seats:  
► Pull strap C to unlock the desired seat and  
give the backrest a slight push forwards.  
Repositioning the seat  
From the outside or from the third row seats:  
► Check that the "aircraft" type tables of the  
front seats are properly folded up.  
► Pull paddle D and guide the backrest  
forwards to tilt it and move the seat forwards.  
To put the seat back in place:  
► Straighten the backrest until the seat locks.  
Whatever the initial position of the seat, it is  
placed automatically a third of the way along  
the longitudinal adjustment range in order to  
preserve enough space for passengers in the  
third row seats.  
Each seat has a continuity panel at the bottom of  
the backrest, which, once unfolded:  
– allows for a continuous loading surface in the  
boot, whatever the position of the seats,  
– prevents objects from sliding beneath the 2nd  
row seats.  
The continuity panels are held against the  
backrests with a magnetic fixing element.  
These continuity panels are not designed  
to support a weight greater than 30 kg.  
► Place the continuity panels of the 2nd row  
seats back against the backrests.  
54  
Ease of use and comfort  
► Pull one of the straps; the 3 parts of the  
corresponding panel fold into concertina form.  
When the 3rd row seats are straightened, these  
folded concertina panels can be left:  
– either flat behind the seats,  
If this system fails (paddle D), the third  
row passengers can also get out after  
having folded the backrest of the second row  
seats using strap C.  
Do not let children operate the seats  
unsupervised.  
3
– or in the vertical position,  
so allowing the seat well to be used for storage.  
Positioning the seats  
These operations are carried out from the boot  
sill.  
Third row seats  
When there is a seat at the back of the boot, the  
removable support is fixed against the front wall  
of its housing.  
If the seat is removed from the back of the boot  
for extra storage space, the removable support  
must be installed on the two lugs on the central  
wall.  
The two third row seats are stored in a retracted  
position in the bottom of the boot. Each one is  
covered with rigid concertina panels, secured to  
the vehicle.  
Folding the concertina  
panels  
Do not let children operate the seats  
unsupervised.  
Each concertina panel can support a  
maximum load of 100 kg with the third  
row seats folded away.  
With the third row seats removed and the  
removable concertina panels supports  
installed, the maximum load is limited to  
50 kg.  
► Remove the load space cover roller.  
► Straighten the continuity panels of the 2nd row  
seats.  
► Fold back the concertina panels and  
straighten them vertically.  
► Pull the black strap E, located behind the  
backrest.  
The backrest tilts backwards bringing the seat  
cushion with it; the seat locks in the open  
position.  
55  
Ease of use and comfort  
The load space cover roller can be stored behind  
the backrests of the 3rd row seats.  
► Put the concertina panels back above the  
folded seats.  
For more information on the Interior fittings,  
and in particular the load space cover roller, refer  
to the corresponding section.  
Before doing anything to the 3rd row  
seats, straighten the continuity panels of  
the 2nd row seats.  
Do not try to fold back a seat in the 3rd row  
without having opened it until the backrest is  
fully locked.  
Do not leave anything on or underneath the  
3rd row seats when they are being folded.  
Do not guide strap F when storing the seat -  
your fingers may get jammed!  
Storing the seats  
► Lift the yellow lever G, located on the right-  
hand side, as far upwards as possible to unlock  
the seat.  
Removing the seats  
Removing the right-hand seat first is  
recommended in order to facilitate access to the  
left-hand seat unlocking control.  
► Straighten the continuity panels of the 2nd row  
seats.  
► Put the head restraints in the low position.  
► Check that the seat belts in the 3rd row are  
properly stored along the side trims without  
being folded or twisted.  
► Pull red strap F, located at the bottom of the  
backrest.  
► While keeping the yellow lever held at the  
top, raise the rear part of the seat using the red  
strap F.  
The seat is unlocked.  
The seat must be in the folded-away position.  
These operations must be performed from the  
boot sill.  
► Push the backrest slightly forwards.  
The backrest tilts and folds back on the cushion;  
the folded seat is stored at the back of its  
storage area.  
► Fold back the concertina panel.  
56  
Ease of use and comfort  
► While holding it by the sides at the plastic  
covers, tilt the seat forwards.  
► Place the hooks located at the front of the  
seat, both at the same time, onto the coloured  
securing lugs on the right and left at the bottom  
of the seat well.  
Seat modularity  
3
Configuration examples  
Check that the front hooks of the seat are  
properly positioned on the two lugs.  
If they are not, you must remove the seat and  
start the procedure again.  
► Once the rear part of the seat has been  
raised, take hold of each side of the seat  
cushion, at the plastic covers, then bring the seat  
towards you, keeping it at the same angle.  
Repositioning the seats  
These operations must be performed from the  
boot sill.  
7 seats  
5 seats  
Transport of  
objects  
As long as the seat is not in the correct  
position, it must be held with both hands  
by the sides, keeping it folded.  
► Release the rear part of the seat which will  
lock in place under its own weight.  
The yellow lever G folds automatically.  
► Check in advance that the seat storage well  
is empty and that the removable support is  
properly secured against the front wall.  
If the seat is not perfectly horizontal, do  
not press on the backrest and do not  
try to unfold it - risk of damaging the  
mechanism!  
Take out the seat and start the operation  
again.  
6 seats  
4 seats  
By folding the second row seats and  
retracting the third row seats, you obtain  
57  
Ease of use and comfort  
a continuous storage floor through to the back  
of the front seats.  
Air distribution  
regulate the automatic air conditioning  
system.  
By placing the front passenger seat in the  
table position, you obtain a continuous  
storage floor through to the dashboard.  
► Operate the air conditioning system for at  
least 5 to 10 minutes once or twice a month to  
keep it in perfect working order.  
► If the system does not produce cold air,  
switch it off and contact a PEUGEOT dealer  
or a qualified workshop.  
Operations on the seats must only be  
done when the vehicle is stationary.  
When towing the maximum load on a steep  
gradient in high temperatures, switching off  
the air conditioning increases the available  
engine power, enhancing the towing capacity.  
Heating and Ventilation  
Air intake  
1. Windscreen demisting/defrosting vents  
2. Front side window demisting/defrosting vents  
3. Adjustable and closable side air vents  
4. Adjustable and closable central air vents  
5. Air outlets to the front footwells  
6. Air outlets to the rear footwells  
7. Adjustable and closable air vents, with blower  
(depending on version)  
Avoid driving for too long with the  
ventilation off or with prolonged operation  
of interior air recirculation. Risk of misting and  
deterioration of the air quality!  
The air circulating in the passenger compartment  
is filtered and originates either from the  
exterior, via the grille located at the base of the  
windscreen, or from the inside in air recirculation  
mode.  
If the interior temperature is very high  
after the vehicle has stood for a long  
time in the sunshine, air the passenger  
compartment for a few moments.  
Put the air flow control at a setting high  
enough to quickly change the air in the  
passenger compartment.  
Controls  
Depending on version, the controls are  
accessible in the "Air conditioning" touch  
screen menu or are grouped together in the  
control panel on the centre console.  
Advice  
Using the ventilation and air  
conditioning system  
► To ensure that air is distributed evenly,  
keep the external air intake grilles at the base  
of the windscreen, the nozzles, the vents, the  
air outlets and the air extractor in the boot  
free from obstructions.  
Condensation created by the air  
conditioning results in a discharge of  
water underneath the vehicle. This is perfectly  
normal.  
► Do not cover the sunshine sensor located  
on the dashboard; this sensor is used to  
58  
Ease of use and comfort  
Servicing the ventilation and air  
conditioning system  
► Ensure that the passenger compartment  
filter is in good condition and have the filter  
elements replaced regularly.  
We recommend using a composite passenger  
compartment filter. Thanks to its special active  
additive, this type of filter helps to purify the  
air breathed by the occupants and keep the  
passenger compartment clean (by reducing  
allergic symptoms, unpleasant odours and  
greasy deposits).  
► To ensure correct operation of the  
air conditioning system, have it checked  
according to the recommendations in the  
Maintenance and Warranty Guide.  
If you keep pressing the "small fan" button until  
all of the indicator lamps go off (system off), the  
temperature is no longer controlled.  
A slight flow of air can still be felt, due to the  
forward movement of the vehicle.  
3
1. Temperature adjustment  
2. Air flow adjustment  
3. Air distribution adjustment  
4. Interior air recirculation  
5. Air conditioning on/off  
Air conditioning on/off  
The air conditioning system is designed to  
operate effectively in all seasons, with the  
windows closed.  
It is used to:  
Adjusting the temperature  
► Turn the knob 1 from blue (cold) to red (hot).  
– lower the temperature in summer,  
– increase the effectiveness of the demisting in  
winter, above 3°C.  
► Press button 5 to turn the air conditioning on/  
off.  
Adjusting the air distribution  
Windscreen and side windows.  
When the system is activated, the indicator lamp  
of the button comes on.  
Central and side air vents.  
Footwells.  
Stop & Start  
The heating and air conditioning systems  
only operate when the engine is running.  
Temporarily deactivate the Stop & Start  
system to maintain a comfortable temperature  
in the passenger compartment.  
Air conditioning does not operate when  
the air flow is disabled.  
To obtain cool air more quickly, enable interior  
air recirculation for a brief period. Then return  
to the intake of exterior air.  
► Press button 3 as many times as necessary  
to obtain the desired air distribution.  
The air distribution can be adapted by combining  
the corresponding orange indicator lamps.  
For more information on the Stop & Start,  
refer to the corresponding section.  
Switching off the air conditioning may result in  
some discomfort (humidity or misting).  
Adjusting the air flow  
► Press one of the buttons 2 “large fan” or  
“small fan” to increase or decrease the air flow.  
The corresponding orange indicator lamps come  
on.  
Manual air conditioning  
The air conditioning system only operates with  
the engine running.  
Mono-zone semi-  
automatic air conditioning  
The air conditioning system only operates with  
the engine running.  
59  
Ease of use and comfort  
The temperature at the nozzles and vents  
is regulated by the system according to the  
temperature in the passenger compartment and  
the temperature setting.  
Temperature adjustment  
Air conditioning on/off  
The air conditioning system is designed to  
operate effectively in all seasons, with the  
windows closed.  
► Press one of the buttons 1 to increase (red)  
or decrease (blue) the value.  
The value displayed corresponds to a level of  
comfort and not to a precise temperature.  
Press the Climate menu button to display  
the system controls page.  
It is used to:  
– lower the temperature in summer,  
– increase the effectiveness of the demisting in  
winter, above 3°C.  
► Press button 5 to activate/deactivate the air  
conditioning system.  
Air flow adjustment  
► Press one of the buttons 2 (- or +) to  
decrease or increase the speed of the air  
booster fan.  
When the system is activated, the indicator lamp  
of the button comes on.  
The air flow symbol (a fan) is filled in  
progressively as the speed of the fan is  
increased.  
When the air flow is reduced to a minimum,  
ventilation stops.  
Air conditioning does not operate when  
the air flow is disabled.  
To obtain cool air more quickly, enable interior  
air recirculation for a brief period. Then return  
to the intake of exterior air.  
"OFF" is displayed alongside the fan.  
Air distribution adjustment  
► Press the buttons 3 to adjust the air flow  
distribution inside the passenger compartment.  
Windscreen and side windows  
Switching off the air conditioning may result in  
some discomfort (humidity or misting).  
1. Temperature adjustment  
2. Air flow adjustment  
3. Air distribution adjustment  
4. Interior air recirculation  
5. Air conditioning on/off  
6. Maximum air conditioning  
7. Switching the system off  
8. Automatic visibility programme  
Maximum air conditioning  
Central and side air vents  
Footwells  
This function automatically adjusts the  
temperature setting to the lowest possible, the  
air distribution towards the central and side air  
vents, the air flow to maximum and activates  
interior air recirculation.  
The lighting of the button indicates that air is  
being blown in the specified direction.  
It is possible to activate all three buttons  
simultaneously, for uniform distribution  
throughout the passenger compartment.  
► Press button 6 to activate / deactivate the  
function (the indicator lamp will come on/switch  
off).  
Once the function is deactivated, the system  
returns to the previous settings.  
60  
Ease of use and comfort  
Automatic Visibility  
programme  
8. Automatic visibility programme  
3
9. Automatic comfort programme on/off  
10. Access to the secondary page  
11. Selection of settings for the Automatic  
comfort programme (Soft/Normal/Fast)  
12. "AQS (Air Quality System)" function (with  
pollution sensor)  
For more information on button 8, refer to the  
“Front Demisting/Defrosting” section.  
Switching the system off  
► Press button 7; all the indicator lamps of the  
system go out.  
This action deactivates all functions of the air  
conditioning system.  
The temperature is no longer regulated. A slight  
flow of air can still be felt, due to the forward  
movement of the vehicle.  
13. Mono-zone/Dual-zone  
14. "REAR" function (depending on version)  
Temperature adjustment  
The driver and front passenger can each choose  
their own temperature setting.  
The value indicated corresponds to a level of  
comfort and not to a precise temperature.  
► Press one of the buttons 1 to increase (red)  
or decrease (blue) the value.  
It is recommended that you avoid a difference of  
more than 3°C in the settings for left and right.  
Dual-zone automatic air  
conditioning  
This air conditioning system operates with  
the engine running, but the ventilation and its  
controls are available with just the ignition on.  
Operation of the air conditioning and regulation  
of temperature, air flow and air distribution in the  
passenger compartment are automatic.  
Press the Climate menu button to display  
the system controls page.  
Automatic Comfort  
programme  
This automatic mode ensures optimum  
management of the passenger compartment  
temperature, air flow and air distribution, based  
on the selected comfort level.  
1. Temperature adjustment  
2. Air flow adjustment  
3. Air distribution adjustment  
4. Interior air recirculation  
5. Air conditioning on/off  
6. Maximum air conditioning  
7. Switching the system off  
► Press button 9 to activate or deactivate the  
air conditioning system’s automatic mode .  
The indicator lamp in the button lights up  
when the air conditioning system is operating  
automatically.  
61  
Ease of use and comfort  
You can adjust the intensity of the  
– air distribution.  
Automatic Visibility  
programme  
For more information on button 8, refer to the  
“Front Demisting/Defrosting” section.  
automatic Comfort programme by using the  
"OPTIONS" button to select a profile:  
– "Soft": provides soft and quiet operation by  
limiting air flow.  
As soon as you modify a setting, the indicator  
lamp in the "AUTO" button goes off.  
► Press button 9 again to reactivate the  
automatic comfort programme.  
– "Normal": offers the best compromise  
between a comfortable temperature and quiet  
operation (default setting).  
"Air Quality System" (AQS)  
function  
Using a pollution sensor, this function  
automatically activates recirculation of the  
interior air once a certain level of polluting  
substances in the exterior air is detected.  
When the air quality returns to a satisfactory  
level, recirculation of interior air is automatically  
deactivated.  
This function is not designed to detect  
unpleasant odours.  
Recirculation is automatically activated when the  
windscreen wash is used or when reverse gear  
is engaged.  
The function does not operate if the exterior  
temperature is below 5 °C, to avoid the risk of  
misting of the windscreen and side windows.  
To activate or deactivate the function, go to the  
secondary page by using the "OPTIONS" button,  
then press button 12.  
Air flow adjustment  
► Press one of the buttons 2 (- or +) to  
decrease or increase the speed of the air  
booster fan.  
The air flow symbol (a fan) is filled in  
progressively as the speed of the fan is  
increased.  
When the air flow is reduced to a minimum,  
ventilation stops.  
"OFF" is displayed alongside the fan.  
– "Fast": provides strong and effective air flow.  
To change the current profile (shown by the  
corresponding indicator lamp), press button 11  
repeatedly until the desired profile is displayed:  
The "Normal" or "Fast" profiles are the most  
comfortable for passengers in the rear seats.  
This profile setting is associated with automatic  
mode only. However, on deactivation of the  
AUTO mode, the indicator lamp for the most  
recently selected profile remains on.  
Adjusting the air distribution  
Changing the profile setting does not reactivate  
AUTO mode if it was deactivated.  
► Press the buttons 3 to adjust the air flow  
distribution inside the passenger compartment.  
Windscreen and side windows.  
In cold weather with the engine cold, the  
air flow is increased gradually until the  
comfort setting has been reached, in order to  
limit the delivery of cold air into the passenger  
compartment.  
On entering the vehicle, if the interior  
temperature is much colder or warmer than  
the comfort setting requested, there is no  
need to alter the value displayed to more  
quickly reach the required level of comfort.  
The system automatically corrects the  
temperature difference as quickly as possible.  
Central and side air vents.  
Footwells.  
The lighting of the button indicates that air is  
being blown in the specified direction.  
For a uniform distribution of air in the passenger  
compartment, the three buttons can be activated  
simultaneously.  
Manual control  
You can manually adjust one or more of these  
functions, while retaining automatic control of the  
other functions by the system:  
In AUTO mode, the indicator lamps in all three  
buttons 3 are off.  
– air flow,  
62  
Ease of use and comfort  
Once the function is deactivated, the system  
returns to the previous settings.  
air vents independently of the air conditioning air  
flow control for the front air vents.  
When the function is deactivated, the maximum  
air flow distributed by the rear air vents is limited  
by the air conditioning air flow setting for the  
front air vents.  
The function is available on the secondary  
page, which can be accessed by pressing the  
“OPTIONS” button.  
► Press button 14 to activate the "REAR"  
function; its status is displayed as "ON".  
► Press the “large fan” or “small fan” button to  
increase or decrease the air flow.  
Air conditioning on / off  
The air conditioning is designed to operate  
effectively in all seasons, with the windows  
closed.  
3
Mono-zone / Dual-zone  
The passenger temperature setting can be linked  
to the driver's setting (mono-zone function).  
It is available in the secondary page by pressing  
the "OPTIONS” button.  
It is used to:  
– lower the temperature in summer;  
– increase the effectiveness of the demisting in  
winter, above 3°C.  
► Press button 5 to activate / deactivate the air  
conditioning system.  
► Press button 13 to activate the "MONO"  
function; its status is displayed as "ON".  
The function is automatically deactivated if the  
passenger uses their temperature adjustment  
buttons (dual-zone function).  
When the system is activated, the indicator lamp  
of the button comes on.  
The air conditioning does not operate  
when the air flow is deactivated.  
To obtain cool air more quickly, use  
recirculation of the interior air for a few  
moments. Then return to the intake of exterior  
air.  
The corresponding indicator lamps come on.  
If all of the indicator lamps are off, a slight air  
flow can still be felt as a result of the vehicle's  
movement.  
“REAR” function  
Ventilation with the ignition  
on  
Switching off the air conditioning may result in  
some discomfort (humidity, misting).  
When the ignition is switched on, you can use  
the ventilation system to adjust the air flow 2  
and air distribution 3 settings in the passenger  
compartment, for a period which depends on the  
battery charge.  
Maximum air conditioning  
This function automatically adjusts the  
temperature setting to the lowest possible, the  
air distribution towards the central and side air  
vents, the air flow to maximum and activates  
interior air recirculation.  
This function does not allow the operation of the  
air conditioning system.  
Switching the system off  
► Press button 7; all the indicator lamps of the  
system go out.  
► Press button 6 to activate / deactivate the  
function (the indicator lamp will come on/switch  
off).  
When this function is activated, the rear air  
vents blower starts up. In this case, the rear  
passengers can control the air flow from these  
63  
Ease of use and comfort  
This action deactivates all functions of the air  
conditioning system.  
The temperature is no longer regulated. A slight  
flow of air can still be felt, due to the forward  
movement of the vehicle.  
► Adjust the air distribution to the "Windscreen"  
position; its associated orange indicator lamp  
comes on.  
► Check that the recirculation of interior air is  
deactivated; its indicator lamp must be off.  
► Switch on the air conditioning by pressing the  
"A/C" button; its orange indicator lamp comes  
on.  
With Stop & Start, when demisting has  
been activated, STOP mode is not  
available.  
In wintry conditions, remove all snow or  
ice on the windscreen near the camera  
before moving off.  
Interior air recirculation  
Otherwise, the operation of the equipment  
The intake of exterior air prevents the formation  
of mist on the windscreen and side windows.  
Recirculating the interior air isolates the  
passenger compartment from outside odours  
and fumes and allows the desired passenger  
compartment temperature to be achieved more  
rapidly.  
associated with the camera may be affected.  
With Stop & Start, when these  
functions - demisting, air conditioning  
and air flow - are activated, STOP mode is  
not available.  
Heated windscreen  
With semi-automatic/  
automatic air conditioning  
► Press this button to activate/deactivate  
the function (confirmed by the  
illumination/extinction of the indicator lamp).  
Automatic Visibility programme  
The function is activated automatically  
when reverse gear is engaged.  
This mode allows the windscreen and side  
windows to be demisted or defrosted as quickly  
as possible.  
► Press this button to activate/deactivate  
the mode (confirmed by the illumination/  
extinction of the indicator lamp).  
The programme automatically manages the air  
conditioning (depending on version), air flow  
and air intake, and provides optimum distribution  
towards the windscreen and side windows.  
It is possible to manually change the air flow  
without deactivating the automatic Visibility  
programme.  
Front demisting  
- defrosting  
In cold weather, this system heats the bottom of  
the windscreen, as well as the area alongside  
the left-hand windscreen pillar.  
Without changing the settings for the air  
conditioning system, it allows faster release  
of the windscreen wiper blades when they are  
frozen to the windscreen and helps to prevent  
With manual air  
conditioning  
► Adjust the temperature to maximum (red).  
► Adjust the air flow to maximum; all of the  
orange indicator lamps come on.  
64  
Ease of use and comfort  
the accumulation of snow resulting from the  
operation of the windscreen wipers.  
Switch off demisting/defrosting as soon  
as you no longer consider it necessary,  
as reducing the consumption of electrical  
current reduces fuel consumption.  
3
On/Off  
Thermal pre-conditioning  
(Hybrid)  
This function allows you to programme the  
vehicle to adjust the passenger compartment  
temperature to a pre-defined, non-modifiable  
temperature (approx. 21°C) before you enter the  
vehicle, on the days and times of your choice.  
This indicator lamp remains lit throughout the  
pre-conditioning phase.  
You can define multiple programmings.  
Each one is saved in the system.  
To optimise battery life, we recommend  
programming with the vehicle plugged in.  
► With the engine running, press this button to  
activate/deactivate the function (confirmed by an  
indicator lamp).  
The function is activated when the exterior  
temperature drops below 0°C. It is deactivated  
automatically when the engine is switched off.  
Programming  
(With PEUGEOT Connect Nav)  
In the Climate > OPTIONS menu:  
Select Temperature conditioning.  
This feature can be programmed using a  
smartphone, via the  
MyPeugeot application.  
With PEUGEOT Connect Radio, the  
programming can only be carried out using a  
smartphone, via the application.  
For more information on Remotely operable  
features, refer to the corresponding section.  
Rear screen demisting/  
defrosting  
► Press + to programme.  
► Select the time of entry into the vehicle and  
the desired days. Press OK.  
► Press ON to activate this programming.  
Pre-conditioning begins approximately 45  
minutes before the programmed time, and is  
maintained for 10 minutes afterwards.  
Demisting/defrosting only operates with the  
engine running.  
Depending on version, this also applies to the  
door mirrors.  
Operating conditions  
– The function is only activated when the  
ignition is off and the vehicle locked.  
– The function is not activated if the battery  
charge level is below 50%.  
► Press this button to activate/deactivate  
the function (confirmed by the  
illumination/extinction of the indicator lamp).  
Demisting/defrosting switches off automatically  
to prevent an excessive consumption of  
electrical current.  
– If recurrent programming is activated (e.g.  
from Monday to Friday) and two pre-conditioning  
65  
Ease of use and comfort  
sequences are performed without the vehicle  
being used, the programming will be deactivated.  
It houses the front passenger airbag deactivation  
switch.  
11. Front armrest with storage  
12. Rear 12 V accessory socket (120 W)  
13. Storage compartment or Rear blower  
14. 230 V/50 Hz socket  
Never drive with the glove box open  
when a passenger is at the front. It may  
cause injury during sharp deceleration!  
Front fittings  
Sun visor  
► With the ignition on, raise the concealing  
flap; depending on the version, the mirror is  
illuminated automatically.  
12 V accessory socket  
This sun visor is also equipped with a ticket  
holder.  
Glove box  
► To open the glove box, raise the handle.  
With the ignition on, the glove box is lit when  
open.  
► Plug in a 12 V accessory (with a maximum  
rated power of 120 W) using a suitable adapter.  
Observe the maximum power rating to  
avoid damaging the accessory..  
1. Grab handle  
2. Sun visor  
3. Card holder  
4. Storage compartment below the steering  
wheel  
5. Illuminated glove box  
6. Door pockets  
7. USB socket / Front 12 V accessory socket  
(120 W)  
The connection of an electrical device  
not approved by PEUGEOT, such as a  
USB charger, may adversely affect the  
operation of vehicle electrical systems,  
causing faults such as poor radio reception or  
interference with displays in the screens.  
8. Storage compartment or Wireless  
smartphone charger  
9. Storage compartment  
10. Cup holder  
66  
Ease of use and comfort  
– High fidelity woofer/mid-range speakers:  
Polyglass technology delivering balance and  
precise sound.  
– TNF tweeters: inverted dome aluminium  
technology giving optimum sound dispersion and  
very detailed higher frequencies.  
– 12-way active amplification - 515 Watts:  
Hybrid Class AB/Class D technology providing  
breadth and finesse in the high frequency  
signals, as well as real power in the bass.  
– Subwoofer: 200 mm triple coil Power FlowerTM  
technology for defined and dynamic reproduction  
of lower frequencies.  
When the USB port is used, the portable  
device charges automatically.  
A message is displayed if the power drawn  
by the portable device exceeds the current  
supplied by the vehicle.  
For more information on how to use this  
equipment, refer to the Audio equipment  
and telematics section .  
USB socket  
3
FOCAL® Premium Hi-Fi  
system  
It allows the connection of a portable device or a  
USB memory stick.  
It reads audio files that are sent to your audio  
system and played via the vehicle's speakers.  
These files can be managed using the steering-  
mounted controls or those on the touch screen.  
Depending on version, the  
Wireless smartphone  
charger  
USB port located on the  
centre console also allows a smartphone to be  
connected by MirrorLinkTM, Android Auto® or  
CarPlay®, so that certain smartphone  
applications can be used on the touch screen.  
To achieve the best results, it is necessary to  
use a cable made or approved by the device  
manufacturer.  
These applications can be managed using the  
steering mounted controls or those of the audio  
system.  
The vehicle is equipped with a high-fidelity  
acoustic system from the French brand FOCAL®.  
10 speakers incorporating exclusive FOCAL®  
technologies offer the pleasure of pure and  
detailed sound inside the vehicle:  
It allows wireless charging of a portable device  
such as a smartphone, using the magnetic  
induction principle, in accordance with the Qi 1.1  
standard.  
The portable device to be charged must be  
compatible with the Qi standard, either by design  
or by using a compatible holder or shell.  
The charging area is identified by the Qi symbol.  
– Central speaker/satellite speakers: Polyglass  
technology delivering sound immersion and  
spatialisation.  
67  
Ease of use and comfort  
The charger works with the engine running and  
with the Stop & Start system in STOP mode.  
Charging is managed by the smartphone.  
With the Keyless Entry and Starting system, the  
charger’s operation may be briefly disrupted  
when a door is opened or the ignition is switched  
off.  
Operating check  
The state of the indicator lamp allows the  
operation of the charger to be monitored.  
If the problem persists, have the system checked  
by a PEUGEOT dealer or a qualified workshop.  
Front armrest  
It includes a refrigerated storage space.  
State of the  
Meaning  
indicator lamp  
Opening  
Off  
Engine switched off.  
No compatible devices  
detected.  
Charging  
► With the charging area clear, place a device  
Charging finished.  
in its centre.  
Fixed green  
Compatible device  
detected.  
Charging.  
When the portable device is detected, the  
charger’s indicator lamp lights up green. It  
remains lit for the whole time that the battery is  
being charged.  
Flashing orange  
Foreign object detected in  
the charging zone.  
Device not well centred in  
the charging zone.  
► Press the lever beneath the cover.  
The cover opens in two parts.  
The system is not designed to charge  
multiple devices simultaneously.  
Fixed orange  
Fault with the device's  
battery meter.  
Storage  
Device battery  
temperature too high.  
Charger malfunction.  
Do not leave any metal objects (coins,  
keys, vehicle remote control, etc.) in the  
charging area while a device is being  
charged, due to the risk of overheating or  
interrupting the charging process.  
If the indicator lamp is lit orange:  
– remove the device, then place it back in the  
centre of the charging zone.  
or  
– remove the device and try again in a quarter  
of an hour.  
The small removable tray can be installed in  
front of or behind the storage space.  
68  
Ease of use and comfort  
A ventilation nozzle circulates fresh air.  
The other mats are simply laid over the carpet.  
3
Closing  
Removing/Refitting  
► To remove it on the driver's side, move the  
seat backwards and unclip the fixings.  
► To refit it, position the mat and secure it by  
pressing.  
To avoid any risk of jamming the pedals:  
– only use mats that are suited to the  
fixings already present in the vehicle; these  
fixings must be used,  
3. Rear courtesy lamp  
– never fit one mat on top of another.  
The use of mats not approved by PEUGEOT  
may interfere with access to the pedals and  
hinder the operation of the cruise control/  
speed limiter.  
4. Rear map reading lamps  
► Replace the two parts of the cover.  
Front and rear courtesy  
lamps  
Mats  
The approved mats have two fasteners  
located underneath the seat.  
In this position, the courtesy lamp comes  
on gradually:  
Fitting  
– when the vehicle is unlocked.  
– when the key is removed from the ignition  
switch.  
Courtesy lamps  
– when a door is opened.  
– when the remote control locking button is  
activated, in order to locate the vehicle.  
It switches off gradually:  
– when the vehicle is locked.  
– when the ignition is switched on.  
– 30 seconds after the last door is closed.  
Permanently off.  
When fitting the mat for the first time, on the  
driver's side use only the fasteners supplied in  
the enclosed sachet.  
1. Front courtesy lamp  
2. Front map reading lamps  
Permanent lighting.  
69  
Ease of use and comfort  
In "Permanent lighting" mode, the lighting time  
varies according to the circumstances:  
– With the ignition off, approximately 10 minutes.  
– In energy saving mode, approximately 30  
seconds.  
Connect only one device at a time to the  
socket (do not use extension leads or  
multi-socket adapters).  
Connect only devices with class II insulation  
(shown on the device).  
Rear fittings  
230 V/50 Hz socket  
– With the engine running, unlimited.  
Do not use metal-cased devices (e.g. electric  
shaver, etc.).  
When the front courtesy lamp is in the  
"Permanent lighting" position, the rear  
courtesy lamp also comes on, unless it is in  
the "Permanently off" position.  
To switch off the rear courtesy lamp, put it in  
the "Permanently off" position.  
As a safety measure, if power  
consumption is high and power is  
required by the vehicle's electrical system  
(due to severe weather conditions, electrical  
overload, etc.), power to the socket may be  
cut off, in which case the green indicator lamp  
goes off.  
Map reading lamps  
It is located at the back of the centre console  
beneath a protective cover.  
This socket (max. power: 150 W) operates with  
the engine running, and with the Stop & Start  
system in STOP mode.  
► With the ignition on, operate the  
corresponding switch.  
12 V accessory socket  
Take care not to place anything in  
contact with the courtesy lamps.  
► Lift the protective cover.  
► Check that the green indicator lamp is on.  
► Connect your multimedia or other electrical  
device (telephone charger, laptop computer,  
CD-DVD player, bottle warmer, etc.).  
In the event of a malfunction, the  
green indicator lamp flashes.  
Have the socket checked by a PEUGEOT dealer  
or a qualified workshop.  
Interior ambience lighting  
The dimmed passenger compartment lighting  
improves visibility in the vehicle when the light  
is poor.  
At night, the ambience lighting automatically  
comes on / switches off when the sidelamps are  
switched on / off.  
► To connect a 12 V accessory (maximum  
power: 120 W), lift the cover and plug in a  
suitable adaptor.  
Activation / deactivation and adjustment  
of the light intensity are set via the  
Driving / Vehicle touch screen menu.  
70  
Ease of use and comfort  
The connection of an electrical device  
not approved by PEUGEOT, such as a  
USB charger, may adversely affect the  
operation of vehicle electrical systems,  
causing faults such as poor radio reception or  
interference with displays in the screens.  
Ski flap  
"Aircraft" type tables  
3
Mechanism for storing and transporting long  
objects.  
Opening  
Rear armrest  
► Lower the rear armrest.  
► Pull the flap handle downwards.  
► To use the table, lower it fully until it locks in  
the low position.  
► To store it, raise the table to the high position,  
passing the point of resistance.  
On the passenger side, do not forget to  
fold it before placing the backrest in the  
"table" position.  
For more information on the Front seats, and  
in particular placing the backrest in the "table"  
position, refer to the corresponding section.  
► Lower the flap.  
► Load the objects from inside the boot.  
The armrest incorporates two cup holders.  
Do not place hard or heavy objects on  
the table.  
They could become dangerous projectiles in  
the event of emergency braking or impact.  
71  
Ease of use and comfort  
Side blinds  
2. 12 V accessory socket (max. 120 W)  
3. Boot lamp  
4. Rear seat folding controls  
5. Hooks  
6. Stowing rings  
7. Adjustable boot floor (2-position)  
8. Storage well/Tool box under the floor  
9. Open storage compartments  
Depending on version, the storage boxes are  
fitted in the floor, at the foot of the side seats on  
the second row.  
On the left-hand side, it may also contain the  
temporary puncture repair kit.  
► To open them, lift the cover by the notch.  
Boot fittings  
Fitted to the second row windows, they protect  
the passenger compartment from the sun's rays.  
► Pull the central tab to unroll the blind.  
► Position the blind's clip on the hook.  
Always guide the blind slowly, using the  
tab, while raising or lowering it.  
1. Load space cover roller  
2. 12 V accessory socket (max. 120 W)  
3. Boot lamp  
Storage boxes  
4. Luggage retaining strap  
5. Storage brackets of the load space cover  
roller  
6. Armrest with cup holder and storage  
compartment  
7. Open storage compartment  
1. Load space cover shelf  
72  
Ease of use and comfort  
– a movable section which rises when the boot  
is opened, with an open storage space.  
In the 5-seat configuration, it is installed behind  
the second row seats, with the third row seats  
stored folded away.  
In the 7-seat configuration, it is stored behind the  
third row seats.  
8. Concertina panels  
9. Stowing rings  
3
The stowing rings are designed to secure  
luggage using different types of retaining  
nets.  
These retaining nets are available as an  
option or as an accessory.  
In the event of sudden deceleration,  
objects placed on the load space cover  
roller can turn into projectiles.  
For more information, contact a PEUGEOT  
dealer.  
Installation  
For information on installing the High load  
retaining net, refer to the corresponding  
section.  
To remove the load space cover shelf:  
► Unhook the two cords.  
► Raise the movable section slightly, then  
unclip it on each side.  
Load space cover shelf  
► Unclip the fixed section on each side, then  
take out the load space cover shelf.  
The load space cover shelf can be stowed under  
the boot floor.  
In the event of sudden deceleration,  
objects placed on the load space cover  
shelf can turn into projectiles.  
► Position the left-hand and right-hand ends of  
the load space cover roller in the cut-outs A, with  
the moving flap at the front.  
► Unwind the roller until it reaches the boot  
pillars.  
► Insert the guides of the roller into the rails in  
pillars B.  
Load space cover roller  
It consists of two sections:  
– a fixed section with an open storage space.  
73  
Ease of use and comfort  
Removal  
► Position the load space cover roller in the  
space located above the armrest, one side after  
the other, tilting it slightly.  
► Slide the load space cover roller as far as  
possible, until it reaches the notches at the back  
of the boot, with the two hinges facing down.  
► Unfold the third row seats.  
The folded concertina panels can be placed in  
the horizontal or upright position.  
To fold the third row seats with the load space  
cover roller stored at the back, it is necessary  
to raise the concertina panels in order to give  
access to the seat unlocking controls (red  
straps).  
► Remove the roller guides from the rails in  
pillars B.  
► Guide the roller as it reels in.  
► Unlock the roller by pressing one of the  
handles located at the ends of the roller bracket.  
High load retaining net  
Storage behind the 3rd row seats  
► Make sure that the third row seats are folded.  
► Fold the first two concertina panels.  
74  
Ease of use and comfort  
► Attach the net’s straps to the lower anchorage Behind the front seats  
points, located directly below the fixings of the  
rear bench seat cushion.  
This removable net allows the entire loading  
volume up to the roof to be used:  
– behind the front seats (1st row) when the rear  
seats are folded down.  
– behind the rear seats (2nd row) when the load  
space cover is removed.  
3
► Pull on the straps to stretch the net.  
Once fitted, the net does not prevent  
tipping of the rear backrests.  
It protects the occupants in case of  
sudden braking.  
Behind the rear seats  
► Fold down the rear seats.  
► Insert the ends of the bar, one after the other,  
into the fixing points in the roof.  
Behind the front seats  
(Depending on version)  
► Remove the caps from the Top Tether fixings.  
► Attach the net’s straps to the lower anchorage  
points, located in the housing of the Top Tether  
fixings.  
► Pull on the straps to stretch the net.  
► Remove the load space cover.  
► Remove the trim covers on each side,  
located in the upper section in the roof.  
► Position the net's upper hooks in the roof.  
► Attach the straps of the net to the lower rings,  
located on each side trim of the boot.  
► Pull on the straps to stretch the net.  
► Fold down the rear seats.  
► Remove the trim covers on each side,  
located in the upper section in the roof.  
► Position the net's upper hooks in the roof.  
75  
Ease of use and comfort  
Behind the rear seats  
On certain versions, the adjustable boot  
floor cannot be fitted in the low position.  
To change the height:  
► Lift and pull the floor towards you using its  
central handle, then use the lateral stops to  
move it.  
► Push the floor all the way forwards to place it  
in the desired position.  
► Remove the load space cover roller.  
► Insert the ends of the bar, one after the other,  
into the fixing points in the roof.  
► Attach the straps of the net to the lower rings,  
located on each side trim of the boot.  
► Pull on the straps to stretch the net.  
2-position boot floor  
To keep it in the inclined position:  
► From the high position, lift the floor towards  
the load space cover.  
► Fully raise the boot floor to access the  
storage well.  
Depending on version, it includes:  
– A temporary puncture repair kit with the tool  
kit.  
– A spare wheel with the tool kit.  
– The battery charging cable (Hybrid).  
The load space cover can also be stowed here.  
► Take it past the retractable stops, then rest  
the floor on these stops.  
This two-position floor allows the boot volume to  
be optimised using the lateral stops located on  
the sides:  
– High position (100 kg max.): to obtain a flat  
floor up to the front seats, when the rear seats  
are folded down.  
Storage well  
– Low position (150 kg max.): maximum boot  
volume.  
76  
Ease of use and comfort  
12 V accessory socket  
► To connect a 12 V accessory (maximum  
power: 120 W), lift the cover and plug in a  
suitable adaptor.  
3
► Switch on the ignition.  
The connection of an electrical device  
not approved by PEUGEOT, such as a  
USB charger, may adversely affect the  
operation of vehicle electrical systems,  
causing faults such as poor radio reception or  
interference with displays in the screens.  
Boot lamp  
It comes on automatically when the boot is  
opened and goes off automatically when the  
boot is closed.  
The lighting time varies according to the  
circumstances:  
– When the ignition is off, approximately 10  
minutes.  
– In energy saving mode, approximately 30  
seconds.  
– With the engine running, unlimited.  
77  

Related Topics

Driving position
Front seats
Steering wheel adjustment
Mirrors
Second row seats
Heating and Ventilation
Front demisting - defrosting
Heated windscreen
Rear screen demisting/defrosting
Front fittings
Rear fittings
Boot fittings