QUICK HELP -> Battery for Your Peugeot Bipper Van First Generation (2007-2018)

Battery  
Starting using another battery  
-
Connect the red cable to the positive  
battery terminal A on your vehicle then  
to the positive (+) terminal of the slave  
battery B.  
-
-
Connect one end of the green or black  
cable to the negative (-) terminal of the  
slave battery B.  
Connect the other end of the green  
or black cable to the earth point C on  
your vehicle (not to the negative battery  
terminal D on your vehicle).  
-
-
Operate the starter, let the engine run.  
Wait for the engine to return to idle, then  
disconnect the cables.  
Some functions are not available if  
the battery is not sufficiently charged.  
Charging the battery using a battery charger  
BATTERY  
Never charge a battery without first  
disconnecting the terminals.  
Models without Stop & Start  
A. Positive battery terminal on your vehicle.  
B. Slave battery.  
-
-
-
Disconnect the two quick-release battery  
terminals.  
Follow the instructions for use provided by  
the battery charger manufacturer.  
C. earth point on your vehicle.  
D. Negative battery terminal on your vehicle.  
Check that the battery posts and terminals  
are clean. If they are covered with sulphate  
(white or greenish deposit), disconnect  
them and clean them.  
-
Reconnect the two quick-release terminals,  
starting with the negative (-) terminal.  
Battery  
-
-
Follow the instructions for use provided  
by the battery charger manufacturer.  
Check that the battery posts and  
terminals are clean. If they are covered  
with sulphate (white or greenish deposit),  
disconnect them and clean them.  
-
-
Reconnect connector F of the check  
sensor G.  
Refit the protective cover A to the  
positive battery terminal B.  
Never remove the check sensor G  
from the negative battery terminal H,  
except when replacing the battery.  
Starting using another battery  
-
Remove the protective cover A from the  
positive battery terminal B.  
-
Connect the red cable to positive battery  
terminal B, then to the (+) terminal of the  
slave battery C.  
Charging the battery using a battery charger  
Do not disconnect the battery to  
charge it.  
Models with Stop & Start  
A. Protective cover.  
-
-
Connect one end of the green or black  
cable to the (-) terminal of the slave  
battery C.  
B. Positive battery terminal on your vehicle.  
C. Slave battery.  
-
-
-
-
Press the release button E to disconnect  
the connector F.  
Connect the other end of the green or  
black cable to the earth point D of your  
vehicle (not to the negative battery  
terminal H of your vehicle).  
D. earth point on your vehicle.  
E. Connector release button.  
F. Check sensor connector.  
G. State of charge sensor.  
Disconnect the connector F from the  
check sensor G.  
-
-
Operate the starter, let the engine run.  
Remove the protective cover A from the  
positive battery terminal B.  
Wait for the engine to return to idle, then  
disconnect the cables.  
H. Negative battery terminal on your vehicle.  
Connect the charger cables: (+) to the  
positive battery terminal B; (-) to the  
negative battery terminal H.  
-
Refit the protective cover A to the  
positive battery terminal B.  
9
Battery  
It is advisable to disconnect the battery  
if the vehicle is not to be used for a  
period of more than one month. to do  
this on models with Stop & Start:  
After reconnecting  
After every reconnection of the battery,  
switch on the ignition and wait 1 minute  
before starting to allow the electronic  
systems to be initialised. If difficulties are  
experienced after this, contact a PeugeOt  
dealer or a qualified workshop.  
If the battery has been disconnected  
for some time, it may be necessary to  
reinitialise the following functions:  
-
press the release button E to  
disconnect connector F,  
the presence of this label, in particular  
-
disconnect connector F of check  
sensor G.  
with the Stop & Start system, indicates  
the use of a 12 V lead-acid battery with  
special technology and specification; the  
involvement of a PeugeOt dealer or  
a qualified workshop is essential when  
replacing or disconnecting the battery.  
Failure to observe this recommendation may  
cause premature wear of the battery.  
Never remove the check sensor G from the  
negative battery terminal H, except when  
replacing the battery.  
-
the display screen settings (date, time,  
language, distance and temperature  
units),  
Before charging  
the charging operation must be carried out in  
a ventilated area away from naked flames or  
any possible sources of sparks to eliminate the  
risks of explosion and fire.  
Do not attempt to charge a frozen battery: it  
must first be thawed to eliminate the risks of  
explosion. If the battery has frozen, before  
charging it have it checked by a specialist who  
will check that the internal components have  
not been damaged and that the container is  
not cracked, which could mean that there is a  
risk of a leak of toxic and corrosive acid.  
-
-
the radio stations,  
the central locking.  
Some settings are cleared and must be  
reprogrammed. Contact a PeugeOt dealer  
or a qualified workshop.  
After refitting the battery by a  
PeugeOt dealer or a qualified  
workshop, the Stop & Start system will  
only be active after a continuous period of  
immobilisation of the vehicle, a period which  
depends on the climatic conditions and the  
state of charge of the battery (up to about  
8 hours).  
Batteries contain harmful substances  
such as sulphuric acid and lead. they  
must be disposed of in accordance with the  
law and must not, in any circumstances be  
discarded with household waste.  
Before disconnecting  
Never disconnect a terminal when the  
engine is running.  
Before disconnecting the battery, you must  
wait for 2 minutes after switching off the  
ignition.  
take used batteries to an authorised waste  
disposal site.  
Close the windows and doors before  
disconnecting the battery.