Get Driving -> Speed Limit recognition and recommendation Guide for Peugeot Rifter 4 Door 2003-2017

Driving

Have it checked by a PEUGEOT dealer or

a qualified workshop.

If a fault occurs in STOP mode, the vehicle may

stall.

All of the instrument panel warning lamps come on.

Depending on version, a warning message may

also be displayed, asking you to place the gear

selector in position N and to press the brake pedal.

With the vehicle stationary, you must switch off the

ignition and then start the engine again.

Suggested speed

(calculated)

Sign detected

Entry into built-

up area

Example:

Without PEUGEOT

Connect Nav

30 mph or 50 km/h

(depending on the units

of the instrument panel)

With PEUGEOT

-

Speed limit signs detected by the camera.

Speed limit details from the navigation

system mapping.

Connect Nav

Display of the speed in

force in the country in

which you are driving.

Speed Limit recognition

and recommendation

Entry into

Without PEUGEOT

intersection zone Connect Nav

Example: 10 mph or 20 km/h

It is necessary to update your navigation

mapping regularly in order to receive

accurate information on speed limits from

the system.

This function is a driving aid that cannot,

in any circumstances, replace the driver's

own vigilance nor compliance with the

highway code.

The actual signs always take priority over

those suggested by the system.

The signs must comply with the Vienna

Convention on road signs.

(depending on the units

of the instrument panel)

With PEUGEOT

-

Certain road signs detected by the camera

(e.g. entering a built-up area).

Connect Nav

Display of the speed in

force in the country in

which you are driving.

This system displays the maximum authorised

speed in the instrument panel, according to

the speed limits in the country in which you are

driving, using:

138

Driving

-

Certain road sign qualifier plates detected by the camera (e.g. the speed limit if towing).

The units for the speed limits (mph or

km/h) depend on the country you are

driving in.

It should be taken into account so that you

observe the speed limit.

For the system to operate correctly when

you change country, the units for speed in

the instrument panel must be those for the

country you are driving in.

Display of the speed associated with

Qualifier plate detected

the qualifier plate

Speed limit in rain

Examples:

If the wiper control stalk is in the

"intermittent wiping" or "automatic

wiping" position (so that the rain sensor is

activated):

68 mph (110 km/h) (for example)

Speed limit if towing

If an approved towing device is fixed to the

vehicle:

56 mph (90 km/h) (for example)

The automatic reading of road signs is

a driving aid system and does not always

display speed limits correctly.

Speed limit applicable over a certain distance

43 mph (70 km/h) (for example)

Example:

The speed limit signs present on the road

always take priority over the display by the

system.

The system cannot, in any circumstances,

replace the need for vigilance on the part

of the driver.

The driver must observe the driving

regulations and must adapt the speed of

the vehicle to suit the weather and traffic

conditions.

It is possible for the system to not display

the speed limit if it does not detect a speed

limit sign within a preset period.

The system is designed to detect signs

that conform to the Vienna Convention on

road signs.

Speed limit for vehicles whose gross vehicle

weight or gross train weight is less than

3.5 tonnes

56 mph (90 km/h) (for example)

6

Speed limit in snow

Example:

If the exterior temperature is below 3°C:

19 mph (30 km/h) (for example)

with a "snowflake" symbol

Speed limit at certain times

Example:

19 mph (30 km/h) (for example)

with a "clock" symbol

139

Driving

Displays in the instrument panel

To maintain correct operation of the

system: regularly clean the area in front of

the camera.

The internal surface of the windscreen can

also become misted around the camera.

In humid and cold weather, demist the

windscreen regularly.

For a suggested maximum speed, the first

time that the vehicle's speed exceeds it by

more than 3 mph (5 km/h) (example: 59 mph

(95 km/h)), the speed flashes for 10 seconds.

Operating limits

The legislation on speed limits is specific to

each country.

The system does not take account of reduced

speed limits in the following cases:

Specific speed limits, such as those for

heavy goods vehicles, are not displayed.

The display of the speed limit in the

instrument panel is updated as you pass

a speed limit sign intended for cars (light

vehicles).

1. Detected speed limit indication.

or

-

atmospheric pollution,

when towing,

driving with a space-saver type spare wheel

or snow chains fitted,

2. Indication of the end of the speed limit.

-

puncture repair using the temporary repair

kit,

young drivers, etc.

Activation/Deactivation

By default, the system is automatically

activated at every engine start.

The system is active but is not detecting speed

limit information.

The following situations may interfere with

the operation of the system or prevent it from

working:

-

poor visibility (inadequate street lighting,

falling snow, rain, fog),

windscreen area located in front of the

camera: dirty, misted, frost-covered, snow-

covered, damaged or covered by a sticker,

fault with the camera,

Activation and deactivation is

done via the vehicle configuration

menu.

-

On detection of speed limit information, the

system displays the value.

-

140

Driving

flashes for a few seconds to offer to make it

-

obsolete or incorrect mapping,

hidden road signs (other vehicles,

vegetation, snow),

Steering mounted controls

a new speed setting.

-

speed limit signs that do not conform to the

standard, are damaged or distorted.

If there is a difference of less than 6 mph

(10 km/h) between the speed setting and

the speed displayed by the Speed Limit

recognition and recommendation, the

MEM symbol is not displayed.

If an app on your smart phone is used

via Mirror Screen, the sign displayed by

the system may be temporarily hidden. It

will be redisplayed as soon as you pass

another sign.

1. Select speed limiter/cruise control mode.

2. Memorise a speed setting.

Depending on the road conditions, several

speeds may be displayed.

Display in the instrument panel

F Make an initial press on button 2 to request

saving of the speed suggested.

A message is displayed to confirm the request.

Recommendation

F Press button 2 again to confirm and save

the new speed setting.

After a predetermined period, the screen

returns to the current display.

3. Speed limit indication.

4. Offer to memorise the speed.

5. Current speed setting.

6

In addition to Speed Limit recognition and

recommendation, the driver can keep the

speed displayed as a speed setting for the

speed limiter or cruise control using the speed

limiter or cruise control memorisation button.

Memorising the speed

Extended Traffic Sign

Recognition

F Switch on the speed limiter/cruise control.

Speed limiter/cruise control information is

displayed.

For more information on the Speed

limiter, Cruise control or Adaptive

cruise control, refer to the corresponding

sections.

Using the camera installed at the top of the

windscreen, this additional system recognises

these road signs and displays them in the

instrument panel.

On detection of a sign offering a new speed

limit, the system displays the value and MEM

141

Download User Manual App

Driving -> Speed Limit recognition and recommendation for Your Peugeot Rifter 4 Door 2003-2017

Related Topics

Driving

Popular Owner Manuals

Latest Owner Manuals