2016-2026 Peugeot Traveller Van In the event of a breakdown -> Changing a bulb User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

In the event of a breakdown -> Changing a bulb for Your Peugeot Traveller Van First Generation (2016-2026)

In the event of a breakdown  
Changing a bulb  
Types of bulb  
Various types of bulb are fitted to your vehicle.  
Type C  
Type E  
To remove them:  
Type A  
Halogen bulb: release the retaining spring from  
its housing.  
Xenon bulb: xenon bulbs must be changed by  
a PeugeoT dealer or a qualified workshop as  
there is a risk of electrocution.  
Type D  
All glass bulb: pull gently as it is fitted by  
pressure.  
Type B  
Halogen bulb: turn the bulb anti-clockwise.  
Halogen bulbs must be changed after  
the headlamp has been off for several  
minutes (risk of serious burns). Do not  
touch the bulb directly with your fingers,  
use lint-free cloths.  
When each operation has been completed,  
check the operation of the lighting.  
Bayonet bulb: press on the bulb then turn it  
anticlockwise.  
298  
In the event of a breakdown  
Front lamps  
Halogen headlamps  
Xenon headlamps  
Front fog lamps  
For more information on Changing a bulb  
and in particular the types of bulb, refer to the  
corresponding section.  
For more information on Changing a bulb  
and in particular the types of bulb, refer to the  
corresponding section.  
Type D, H11-55W  
1. Sidelamps.  
1. Main beam headlamps.  
Type C, H1-55W  
Type A, W5W-5W  
2. Main beam headlamps.  
Type C, H1-55W  
2. Dipped beam headlamps.  
Type E, D8S 25W  
3. Dipped beam headlamps.  
Type C, H7-55W  
3. Direction indicators.  
Type B, PY21W-21W (amber)  
4. Daytime running lamps.  
Type A, W21W LL-21W  
5. Direction indicators.  
Type B, PY21W-21W (amber)  
In some weather conditions (e.g. low  
8
temperature or humidity), the presence  
of misting on the internal surface of the  
glass of the headlamps and rear lamps  
is normal; it disappears after the lamps  
have been on for a few minutes.  
For H7 type bulbs with lugs... take care  
to observe their correct installation  
so as to ensure the best lighting  
performance.  
299  
In the event of a breakdown  
Daytime running lamps /  
sidelamps  
Direction indicator side  
repeater  
The headlamps have polycarbonate  
lenses with a protective coating:  
F
do not clean them using a dry  
or abrasive cloth, nor with a  
detergent or solvent product,  
use a sponge and soapy water or a  
pH neutral product,  
Type A, WY5W-5W (amber)  
F
F
when using a high pressure washer  
on persistent marks, do not keep  
the lance directed towards the  
lamps or their edges for too long,  
so as not to damage their protective  
coating and seals.  
If fitted to your vehicle, contact a PeugeoT  
dealer or a qualified workshop for the  
replacement of this type of LeD lamp and light  
guide.  
A replacement kit for the LeDs is available from  
PeugeoT dealers.  
-
-
Push the repeater towards the rear and  
disengage it.  
When refitting, engage the repeater towards  
the front and then bring it towards the rear.  
Changing a bulb should only be done  
after the headlamp has been switched  
off for several minutes (risk of serious  
burns).  
Amber coloured bulbs (direction indicators and  
side repeaters) must be replaced with bulbs of  
identical specification and colour.  
F
Do not touch the bulb directly with  
your fingers, use a lint-free cloth.  
It is imperative to use only anti-  
ultraviolet (uV) type bulbs to avoid  
damaging the headlamp.  
Always replace a failed bulb with a  
new bulb with the same type and  
specification.  
300  
In the event of a breakdown  
Dipped beam headlamps  
(halogen headamps)  
Type C, H7-55W  
Daytime running lamps  
(halogen headlamps)  
Type A, W21W LL-21W  
Sidelamps  
(halogen headlamps)  
Type A, W5W  
F
F
Press the upper clip on the cover then tip it  
rearwards to remove it.  
Press the lower clip on the electrical  
connector and remove the assembly of  
connector and bulb.  
F
F
Press the upper clip on the cover then tip it  
rearwards to remove it.  
Press the two side clips on the electrical  
connector and remove the assembly of  
connector and bulb.  
F
F
Press the upper clip on the cover then tip it  
rearwards to remove it.  
Press the two side clips on the electrical  
connector and remove the assembly of  
connector and bulb.  
F
Pull the bulb out and change it.  
F
Pull out the bulb and change it.  
F
Pull the bulb out and change it.  
To refit, carry out these operations in reverse  
order.  
To refit, carry out these operations in reverse  
order.  
To refit, carry out these operations in reverse  
order.  
8
When refitting the connector and bulb  
in the lamp, push the assembly into its  
housing until it clicks into place.  
301  
In the event of a breakdown  
Main beam headlamps  
(halogen headlamps)  
Type C, H1-55W  
Direction indicators  
(halogen headlamps)  
Type B, PY21W-21W (amber)  
F
F
Press the upper clip on the cover then tip it  
rearwards to remove it.  
Press the lower clip on the electrical  
connector and remove the assembly of  
connector and bulb.  
F
F
Press the upper clip on the cover then tip it  
rearwards to remove it.  
Turn the bulb holder a quarter turn anti-  
clockwise.  
Remove the bulb holder.  
Change the failed bulb.  
F
F
F
Pull the bulb out and change it.  
To refit, carry out these operations in reverse  
order.  
To refit, carry out these operations in reverse  
order.  
Be aware that the area behind the right-  
hand headlamp (facing forwards) may  
be hot, with the risk of burns (overflow  
pipe).  
Faster flashing of a direction indicator  
warning lamp (left or right) indicates a  
failed bulb on that side.  
302  
In the event of a breakdown  
Dipped beam headlamps  
(xenon headlamps)  
Type E, D8S 25W  
Main beam headlamps  
(xenon headlamps)  
Type C, H1-55W  
Direction indicators  
(xenon headlamps)  
Type B, PY21W-21W (amber)  
F
F
Press the upper clip on the cover then tip it  
rearwards to remove it..  
Press the lower clip on the electrical  
connector and remove the assembly of  
connector and bulb.  
F
F
F
Press the upper clip on the cover then tip it  
rearwards to remove it.  
Turn the bulb holder a quarter turn anti-  
clockwise.  
Replacement of D8S xenon bulbs must  
be done by a PeugeoT dealer or a  
qualified workshop as there is a risk of  
electrocution.  
It is recommended that both D8S bulbs  
be replaced at the same time, in the  
event of the failure of one of them.  
Change the failed bulb.  
F
Pull the bulb out and change it.  
To refit, carry out these operations in reverse  
order.  
To refit, carry out these operations in reverse  
order.  
8
When refitting the connector and bulb  
in the lamp, push the assembly into its  
housing until it clicks into place.  
Faster flashing of a direction indicator  
warning lamp (left or right) indicates a  
failed bulb on that side.  
303  
In the event of a breakdown  
Front foglamps  
Type C, H11-55W  
F
F
Press the locking clip and disconnect the  
connector.  
Turn the bulb holder a quarter turn anti-  
clockwise.  
Remove the bulb holder.  
Change the failed bulb.  
F
F
Below the front bumper, unscrew the fixing  
screws for the deflector A.  
Remove the deflector A.  
F
F
To refit, carry out these operations in reverse  
order.  
You can also go to a PeugeoT  
dealer or a qualified workshop for the  
replacement of these bulbs.  
304  
In the event of a breakdown  
F
Identify the failed bulb then open the rear  
doors.  
Rear lamps  
(side-hinged rear doors)  
For more information on Changing a bulb and  
in particular, the types of bulbs, refer to the  
corresponding section.  
F
F
Spread the three lugs slightly, then extract  
the bulb holder.  
Remove the failed bulb by pressing  
lightly on it, then turning it a quarter turn  
clockwise.  
F
F
From inside, remove the ventilation grille, if  
your vehicle has one.  
From outside, unscrew the two lamp fixing  
screws.  
F
Change the bulb.  
To reassemble, carry out these operations in  
reverse order.  
1. Brake lamps / sidelamps.  
Type B, P21/5W-21/5W  
2. Direction indicators.  
Type B, PY21W-21W (amber)  
3. Reversing lamps.  
Type B, P21W-21W  
4. Foglamps / sidelamps.  
Type B, P21/4W-21/4W.  
8
For vehicles with interior trim, contact  
a PeugeoT dealer or a qualified  
workshop to have the work done.  
F
F
While holding the lamp in place, press the  
clip on the inside then carefully remove the  
lamp.  
Disconnect the electrical connector.  
305  
In the event of a breakdown  
Third brake lamp  
(side-hinged doors)  
Type A, W5W-5W  
Number plate lamps  
(side-hinged doors)  
Type A, W5W-5W  
F
F
Remove the plastic cover using a small  
screwdriver.  
using a screwdriver through the aperture,  
push the lamp towards the outside.  
Disconnect the electrical connector.  
Remove the lamp.  
F
open the left hand rear door.  
F
Insert a thin screwdriver into one of the cut-  
outs in the lens.  
F
F
F
F
F
F
Push it outwards to unclip it.  
Remove the lens.  
Change the failed bulb.  
Turn the bulb holder a quarter turn anti-  
clockwise.  
F
Change the failed bulb.  
To refit, press on the lamp to clip it in place.  
To refit, press on the lens to clip it in place.  
306  
In the event of a breakdown  
Courtesy lamps  
(front and rear)  
Type A, W5W-5W  
F
unclip the lens by inserting a thin  
screwdriver into the cut-outs at each side  
of the lamp.  
F
F
Pull the bulb out and change it.  
Clip the lens in place and ensure that it is  
secure.  
8
307  
In the event of a breakdown  
F
Identify the failed bulb then open the boot.  
Rear lamps  
(tailgate)  
For more information on Changing a bulb and  
in particular, the types of bulbs, refer to the  
corresponding section.  
F
F
While holding the lamp in place, press the  
clip on the inside then carefully remove the  
lamp.  
Disconnect the electrical connector.  
F
From inside, remove the cover, if your  
vehicle has one.  
1. Brake lamps / sidelamps.  
Type B, P21/5W-21/5W  
2. Direction indicators.  
Type B, PY21W-21W (amber)  
3. Reversing lamps.  
Type B, P21W-21W  
4. Foglamps / sidelamps.  
Type B, P21/4W-21/4W  
F
F
Spread the three lugs slightly, then extract  
the bulb holder.  
Remove the failed bulb by pressing  
lightly on it, then turning it a quarter turn  
clockwise.  
F
Change the bulb.  
F
F
From the outside, press on the inner clips  
on the plastic finisher then tip it towards the  
outside to remove it.  
For vehicles with interior trim, contact  
a PeugeoT dealer or a qualified  
workshop to have the work done.  
To reassemble, carry out these operations in  
reverse order.  
unscrew the two lamp fixing screws.  
308  
In the event of a breakdown  
Third brake lamp  
(tailgate)  
Number plate lamps  
(tailgate)  
Type A, W5W-5W  
Type A, W5W-5W  
F
F
F
unclip the trim at each end by turning it  
upwards.  
Pull on the trim to disengage the central  
clips, then remove it.  
using a screwdriver through the aperture,  
push the lamp towards the outside.  
Disconnect the electrical connector.  
Remove the lamp.  
Turn the bulb holder a quarter turn anti-  
clockwise.  
F
open the tailgate.  
F
Insert a thin screwdriver into one of the cut-  
outs in the lens.  
Push it outwards to unclip it.  
Remove the lens.  
F
F
F
F
F
F
Change the failed bulb.  
F
Change the failed bulb.  
To refit, carry out these operations in reverse  
To refit, press on the lens to clip it in place.  
8
order.  
To refit the lamp and trim, press on them to clip  
them in place.  
309  
In the event of a breakdown  
Courtesy lamps  
(front and rear)  
For the replacement of this type of LeD lamp  
and light guide, contact a PeugeoT dealer or  
a qualified workshop.  
A replacement kit for the LeDs is available from  
PeugeoT dealers.  
310  

Related Topics

In the event of a breakdown
Warning triangle / Tool box Puncture repair kit Changing a wheel Changing a fuse 12 V battery (Charging/Starting) Towing Running out of fuel

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot