Get Wheels Guide for Skoda Enyaq 4 Door First Generation (2020-2024)

222 Wheels › Tyres and rims

WARNING

Wheels

Vehicles with a 150 kW electric motor have diﬀerent tire sizes

on the front and rear axles.

Tyres and rims

Do not exchange wheels on these vehicles.

▶

What you should be mindful of

Advice for tyre assembly

With directional tires, the correct direction of rotation must be

observed. The direction of rotation of the tyres is marked by

arrows on the wall of the tyre.

NOTICE

›

Protect tyres from contact with lubricants and fuel.

▶

Always store wheels or tyres in a cool, dry and, where possible,

dark place. Tyres without rims should be stored in an upright

position.

Alloy rims can be damaged by grit.

Do not use light alloy rims with a high-sheen surface in wintry

weather conditions or with snow chains

Always replace the tyres by the axle.

›

Additional information

Only ﬁt radial tyres of the same type, size (rolling circumference)

and the same tread pattern on one axle.

▶

Approved tyre sizes are speciﬁed in the technical vehicle docu-

mentation and in the declaration of conformity (in the so-called

COC Document).

Causes of uneven tyre wear

Improper tyre pressure.

▶

Driving style (e.g. fast cornering, rapid acceleration and decel-

eration).

▶

The declaration of conformity can be obtained from a ŠKODA

Partner (valid for some countries and some models).

Wheel alignment errors.

Incorrect wheel balancing.

▶

Overview of tyre labelling

Wheel changes

Applies to vehicles with 132 kW electric engine.

Explanation of tyre markings

e.g. 235/55 R 19 101 T

For uniform wear on all tyres, we

235 Tyre width in mm

55 Height/width ratio in %

recommend that you change the

wheels every 10,000 km according

to the schedule.

R

Code letter for the type of tyre - Radial

19 Diameter of wheel in inches

101 Load index

T

Speed symbol

Applies to vehicles with 150 kW electric engine.

Wheels › Tyres and rims 223

Load index

Tread wear indicators

The load index indicates the maximum permissible load for each

individual tyre.

Wear indicators are located in the

proﬁle of the tyres that display the

permissible minimum tread depth.

100 800 kg

101 825 kg

102 850 kg

103 875 kg

Markings on the walls of the tyres

with the letters TWI or other sym-

bols (e.g. ) indicate the position of

the wear indicators.

Speed symbol

The speed symbol indicates the maximum permissible speed for

a vehicle ﬁtted with tyres in the category concerned.

A tyre is to be regarded as worn out

when this wear indicator is ﬂush

with the tread.

S

T

U

H

V

W

Y

180 km/h

190 km/h

200 km/h

210 km/h

240 km/h

270 km/h

300 km/h

The tread depth can be measured using a tread depth gauge

on the ice scraper. The ice scraper is located on the inside of the

boot lid.

WARNING

Risk of accident!

Do not use worn tires.

▶

WARNING

Tyre manufacturing date

The date of manufacture is indicated on the tyre sidewall.

Do not exceed the maximum permissible load and speed for

the mounted tires.

▶

For example, DOT ... 18 20 means that the tyres were produced

in the 18th week of the year 2020.

WARNING

Risk of an accident!

Do not use tyres that are older than 6 years.

▶

Troubleshooting

Help with a ﬂat tyre

Breakdown kit » page 227.

▶

224 Wheels › All-season or winter tires

Change of tyre pressure

In the driver's ﬁeld of view, aﬃx a warning label with the maxi-

mum value of the speed category intended for the tyres ﬁtted

(applies only to certain countries).

›

illuminates

Stop the vehicle.

Check the tyres and tyre pressures.

›

Settings

The speed limit setting for tyres is set in the Infotainment in the

All-season or winter tires

Usage

following menu

.

Outside.

By moving your ﬁnger sideways, choose the screen with the

›

menu item Tyres

.

All-season or winter tyres improve handling in winter weather

conditions. They are characterised by ‘M+S’ and a mountaintop

Select Tyres – select them and set the speed limit.

and snowﬂake symbol

.

Snow chains

What you should be mindful of

Usage

For the best possible handling, use tyres on all four wheels with a

minimum tread depth of 4 mm.

The snow chains improve driving in wintry road conditions.

WARNING

Risk of accident as well as tyre damage!

Do not use chains on routes that are free from snow and ice.

Change winter tyres to summer tyres at the appropriate time.

Summer tyres have better driving and braking characteristics on

snow- and ice-free roads and at temperatures above 7 °C.

▶

What you should be mindful of

Usage conditions

Before ﬁtting the snow chains, remove the full wheel trims.

Only mount the snow chains on the rear wheels.

›

If all-season or winter tyres are installed that have a lower speed

category than the actual speciﬁed maximum vehicle speed, then

proceed as follows:

In Infotainment, set the speed limit according to the category

of tyres ﬁtted.

›

Technical data

Permitted rim/tyre combinations for mounting of snow chains:

Wheels › SEAL tyres 225

Raise vehicle

WARNING

Rim size

Tyre size

8Jx19 ET45

235/55 R19

255/50 R19

Always ensure the base plate of the lifting jack cannot slip!

Provide a wide and ﬁrm base under the jack on loose surfaces.

Create a non-slip base (e.g. a rubber ﬂoor mat) under the jack

on a smooth surface.

▶

Only ﬁt snow chains with links and locks that are no larger than

9 mm.

▶

Always raise the vehicle with the doors closed.

Do not insert any body parts under the raised vehicle.

Do not turn on ignition of the lifted vehicle.

▶

SEAL tyres

Usage

NOTICE

Danger of damage to vehicle!

The SEAL tyres have increased resistance to air leakage when

punctured.

Make sure that the jack is attached correctly to the bridge of

the sill.

▶

When replacing SEAL tyres with standard tires, the vehicle must

have one of the following pieces of equipment.

After having been changed

Check the tyre pressure on the mounted wheel and adjust if

necessary.

In vehicles with a tyre indicator, save the tyre pressure values

in the system.

›

Spare or emergency spare wheel with corresponding tool for

replacing it.

Breakdown kit.

▶

›

▶

Have the tightening torque of the wheel bolts of the mounted

tyres checked with a torque wrench as soon as possible.

›

Changing the wheel and raising the vehicle

What you should be mindful of

Before changing

The speciﬁed tightening torque is 120 Nm.

Drive carefully until the tightening torque is checked.

Replace the damaged tyre. It is not recommended to repair the

tyre.

Park the vehicle securely and secure it from rolling away.

Switch oﬀ the ignition.

Let all of the occupants get out. During the wheel change they

›

should not stand on the road, e.g. behind the crash barriers.

Close all doors, the boot and front ﬂap.

Uncouple any trailers.

›

226 Wheels › Changing the wheel and raising the vehicle

Place the key on the wheel bolt or

on the attachment piece.

Turn the screw a maximum of half

a turn so that the wheel does not

come loose and fall oﬀ.

WARNING

Risk of an accident!

Too low a tightening torque may cause the wheel to disengage

while driving.

Too high a tightening torque can damage the threads and

cause the rim to deform.

›

▶

WARNING

Risk of an accident!

Do not grease or lubricate screws.

▶

Do not use corroded or damaged screws.

▶

Jacking points for the jack

Changing the wheel and raising the vehicle

Release screws

If the vehicle has covers over the wheel bolts or wheel trims,

remove them.

›

WARNING

If you step on the key end when loosening the screw, hold on

▶

to the vehicle for better stability.

Some vehicles may have anti-theft

wheel bolts that protect the wheels

from theft.

A

B

18 cm

30 cm

Insert the upper section on the an-

›

ti-theft wheel bolt until it stops.

Wheels › Breakdown kit 227

Position the jack and lift the vehicle

Tighten screws

Tighten the opposite wheel bolts including the anti-theft

wheel bolt one after the other.

›

Reinstall the cover caps of the wheel bolts or the full wheel

covers.

›

Keep the label with the code number of the anti-theft wheel

bolts. A replacement upper section can be acquired from ŠKO-

DA original parts based on this.

Breakdown kit

Position the jack at the jacking point closest to the wheel to be

replaced.

›

Content overview

The kit is located in a box under the ﬂoor covering in the luggage

compartment.

Support the base plate of the jack with its full area resting on

level ground and ensure that the jack is located in a vertical po-

sition at the jacking point.

›

Use the crank to raise the jack until its claw encloses the bar.

Continue to lift the vehicle until the wheel is just oﬀ the ﬂoor.

›

Changing a wheel

Unscrew the screws and place them on a clean surface.

Remove the wheel carefully.

Attach the wheel.

Slightly screw in the screws.

›

Lower the vehicle.

›

NOTICE

A

B

C

Sticker with speed indication

Valve remover

Applies to wheel trims supplied ex-factory or from ŠKODA

Original Accessories: the anti-theft wheel bolt should be in-

stalled in the position marked on the back of the wheel trim.

▶

Inﬂation hose with plug

228 Wheels › Breakdown kit

After using the kit

D

Air compressor (the layout of the controls may be diﬀerent

If a tyre pressure of 2.0 bar cannot be achieved, the tyre is too

damaged and cannot be sealed with the puncture set.

depending on the type of air compressor)

E

F

G

H

I

Tyre inﬂation hose

Stop driving. Seek the help of a specialist garage.

›

Button for pressure reduction

Pressure indicator

Once a tyre pressure of 2.0–2.5 bar is achieved, continue the

journey at a maximum speed of 80 km/h (50 mph).

12 volt cable connector

ON and OFF switch

Avoid full accelerations, strong braking and fast cornering.

›

Information for driving with repaired tyres

J

Tyre inﬂation bottle

The pressure of the repaired tyre must be checked after driv-

ing for 10 minutes.

›

K

Replacement valve core

If the tyre pressure is 1.3 bar and less, do not continue! Seek

the help of a specialist garage.

If the tyre pressure is higher than 1.3 bar, correct the pressure

to the correct value of at least 2 bar and continue driving.

›

The declaration of conformity is included with the air compres-

sor or the log folder.

›

Usage conditions

NOTICE

Danger of damage to the compressor!

Performing a repair with the breakdown kit not at all intended to

replace a permanent repair on the tyre.

After the maximum running time of the air compressor, allow

it to cool for a few minutes.

▶

The purpose of the repair is to get you to the nearest specialist

garage.

WARNING

Risk of burns!

Change the tyre repaired by the breakdown kit as soon as possi-

ble.

The tyre inﬂation hose and the air compressor may become hot

when inﬂated.

Allow the air compressor and hose to cool for a few minutes.

▶

Before using the kit

Park the vehicle securely and secure it from rolling away.

Switch oﬀ the ignition.

Let all of the occupants get out. During the wheel repair they

should not stand on the road, e.g. behind the crash barriers.

›

Usage restrictions

›

Do not use the kit in the following cases:

Close all doors, the boot and front ﬂap.

Uncouple any trailers.

›

The rim is damaged.

▶

Wheels › Tyre pressure 229

The outdoor temperature is below the minimum temperature

indicated in the manual of the tyre ﬁlling bottle.

Once a tyre pressure of 2.0-2.5 bar is reached, turn oﬀ the air

compressor.

▶

›

Tyre punctures are greater than 4 mm.

There is damage to the tyre wall.

The expiry date stated on the tyre inﬂation bottle has expired.

▶

Observe the maximum running time of the air compressor ac-

cording to the directions of the repair kit manufacturer.

If an air pressure of 2.0 - 2.5 bar has not been reached, remove

›

the tyre inﬂation hose from the valve.

Drive approx. 10 metres forwards or backwards to allow the

sealing agent to distribute in the tyre.

›

Self-help

Replace the tire inﬂation hose on the valve and repeat the inﬂa-

tion procedure.

Seal the tyres

›

Unscrew the valve cap from the damaged tyre.

Unscrew the valve core with the valve insert and place it on a

clean surface.

›

Tyre pressure

Shake the tyre inﬂation bottle back and forth with sealant.

Screw the inﬂation hose onto the tyre inﬂater bottle. The ﬁlm

on the closure is pierced automatically.

›

What you should be mindful of

NOTICE

Remove the plug from the inﬂation hose and push it fully onto

the tyre valve.

Hold the bottle with the bottom facing upwards and ﬁll all of

the sealing agent into the tyre.

›

Always adjust the tyre pressure to the load.

Check the pressure in all tyres at least once a month and be-

fore each longer ride.

▶

›

Check the pressure when the tyres are cold. Do not reduce the

higher pressure of warm tyres.

After each change in tyre pressure, save the new values in the

tyre control display.

▶

Remove the ﬁller plug from the valve.

Screw in the valve insert.

›

Inﬂate tyres

Fit the tyre inﬂation hose of the air compressor to the tyre

valve.

Secure the vehicle with the parking brake.

Turn on the ignition.

Plug the connector into the 12 volt socket .

Turn on the air compressor.

›

WARNING

Risk of an accident!

If tyre pressure loss is very quick, try to stop the vehicle care-

fully without heavy steering or heavy braking.

›

▶

›

230 Wheels › Tyre pressure monitor

Show tyres with modiﬁed pressure

Sticker with prescribed tyre pressures

Select the menu item for displaying the tyre condition in menu

›

The sticker with the prescribed tyre pressure values is located in

the centre body pillar on the driver’s side.

.

Inﬂation pressure for half load

Inﬂation pressure for a full load

Tyre diameter in inches

This information only serves as

information for the prescribed

tyre pressure. This is not a listing

of approved tyre sizes for your

A

B

C

Function restriction

The system is unable to provide a warning in the event of a very

rapid tyre pressure loss, e.g. sudden puncture.

The system function may be restricted in the following cases:

Uneven loading of the wheels, e.g. with a trailer attached

Sporty driving style

Driving on dirt roads

▶

vehicle. These are in the vehicle's technical documentation,

as well as in the declaration of conformity (in the so-called

COC document).

Snow chains ﬁtted

Tyre pressure reading for the front axle tyres

D

E

Saving tyre pressure values

Tyre pressure reading for the rear axle tyres

Press the

button under the Infotainment.

›

Tyre pressure monitor

Functionality

In the displayed menu in Infotainment, tap the functional sur-

›

face

.

Then follow the instructions on the screen.

›

The tyre pressure monitoring indicator indicates a change in tyre

pressure.

Save the tyre pressures in the following cases:

Change of tyre pressure

Change of one or more wheels

Change of position of a wheel on the vehicle

Always after covering a distance of 10,000 km or once a year

▶

Warning when pressure changes

illuminates

Stop the vehicle.

Check the tyres and tyre pressures.

›

Wheels › Wheel bolt cover caps 231

Troubleshooting

Full wheel frame

Tyre pressure display faulty

Removing and installing the trim

ﬂashes for about 1 minute and stays on

Applies to factory built or original accessory trims from ŠKODA.

Stop the car, turn the ignition oﬀ and on again.

›

Disconnecting

If the symbol ﬂashes again after turning on ignition, there is

a system fault.

Hang the clamps for removing the wheel trims at the edge of

one of the openings in the trim.

›

Continue driving, exercising appropriate caution, and seek the

help of a specialist garage.

›

Push the wheel wrench through the clamp, support on the tyre

and pull oﬀ the wheel trim.

›

Installing

Press the wheel trim onto the wheel rim at the designated

valve opening.

›

Wheel bolt cover caps

Remove cover caps and install

Disconnecting

When using an anti-theft wheel bolt, it must be located at the

location indicated on the bezel.

Press the trim, starting at the valve, into the rim on both sides

›

Push the pull-oﬀ clamp onto the

›

until it engages around the entire circumference.

cover cap up to the stop.

NOTICE

Remove the cover cap.

›

Use hand pressure, do not hit the wheel cover.

▶

Installing

Push the cover cap onto the wheel bolt to the stop.

›

Wheels for Your Skoda Enyaq 4 Door First Generation (2020-2024)

Related Topics

Popular Owner Manuals

Latest Owner Manuals