2020-2024 Skoda Enyaq 4 Door Wheels -> Breakdown kit User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Wheels -> Breakdown kit for Your Skoda Enyaq 4 Door First Generation (2020-2024)

Wheels › Breakdown kit 227  
Position the jack and lift the vehicle  
Tighten screws  
Tighten the opposite wheel bolts including the anti-theft  
wheel bolt one after the other.  
›
Reinstall the cover caps of the wheel bolts or the full wheel  
covers.  
›
Keep the label with the code number of the anti-theft wheel  
bolts. A replacement upper section can be acquired from ŠKO-  
DA original parts based on this.  
Breakdown kit  
Position the jack at the jacking point closest to the wheel to be  
replaced.  
›
Content overview  
The kit is located in a box under the floor covering in the luggage  
compartment.  
Support the base plate of the jack with its full area resting on  
level ground and ensure that the jack is located in a vertical po-  
sition at the jacking point.  
›
Use the crank to raise the jack until its claw encloses the bar.  
Continue to lift the vehicle until the wheel is just off the floor.  
›
›
Changing a wheel  
Unscrew the screws and place them on a clean surface.  
Remove the wheel carefully.  
Attach the wheel.  
Slightly screw in the screws.  
›
›
›
›
Lower the vehicle.  
›
NOTICE  
A
B
C
Sticker with speed indication  
Valve remover  
Applies to wheel trims supplied ex-factory or from ŠKODA  
Original Accessories: the anti-theft wheel bolt should be in-  
stalled in the position marked on the back of the wheel trim.  
▶
Inflation hose with plug  
228 Wheels › Breakdown kit  
After using the kit  
D
Air compressor (the layout of the controls may be different  
If a tyre pressure of 2.0 bar cannot be achieved, the tyre is too  
damaged and cannot be sealed with the puncture set.  
depending on the type of air compressor)  
E
F
G
H
I
Tyre inflation hose  
Stop driving. Seek the help of a specialist garage.  
›
Button for pressure reduction  
Pressure indicator  
Once a tyre pressure of 2.0–2.5 bar is achieved, continue the  
journey at a maximum speed of 80 km/h (50 mph).  
12 volt cable connector  
ON and OFF switch  
Avoid full accelerations, strong braking and fast cornering.  
›
Information for driving with repaired tyres  
J
Tyre inflation bottle  
The pressure of the repaired tyre must be checked after driv-  
ing for 10 minutes.  
›
K
Replacement valve core  
If the tyre pressure is 1.3 bar and less, do not continue! Seek  
the help of a specialist garage.  
If the tyre pressure is higher than 1.3 bar, correct the pressure  
to the correct value of at least 2 bar and continue driving.  
›
The declaration of conformity is included with the air compres-  
sor or the log folder.  
›
Usage conditions  
NOTICE  
Danger of damage to the compressor!  
Performing a repair with the breakdown kit not at all intended to  
replace a permanent repair on the tyre.  
After the maximum running time of the air compressor, allow  
it to cool for a few minutes.  
▶
The purpose of the repair is to get you to the nearest specialist  
garage.  
WARNING  
Risk of burns!  
Change the tyre repaired by the breakdown kit as soon as possi-  
ble.  
The tyre inflation hose and the air compressor may become hot  
when inflated.  
Allow the air compressor and hose to cool for a few minutes.  
▶
Before using the kit  
Park the vehicle securely and secure it from rolling away.  
Switch off the ignition.  
Let all of the occupants get out. During the wheel repair they  
should not stand on the road, e.g. behind the crash barriers.  
›
›
Usage restrictions  
›
Do not use the kit in the following cases:  
Close all doors, the boot and front flap.  
Uncouple any trailers.  
›
›
The rim is damaged.  
▶

Related Topics

Wheels
Tyres and rims All-season or winter tires Snow chains SEAL tyres Changing the wheel and raising the vehicle Tyre pressure Tyre pressure monitor Wheel bolt cover caps Full wheel frame

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot