Get Before Driving -> Instrument Cluster (Type A) (if equipped) Guide for Suzuki Baleno 4 Door Second Generation (2015-2021)

2-51

BEFORE DRIVING

1. Speedometer

2. Fuel gauge

3. Information display

4. Trip meter selector knob

5. Indicator selector knob

6. Warning and indicator lights

68PH02201

324 5

EXAMPLE

Instrument Cluster (Type A) (if equipped)

2-52

BEFORE DRIVING

Speedometer

The speedometer indicates vehicle speed.

Fuel Gauge

68PH02202

When the ignition switch is in the “ON”

position, this gauge gives an approximate

indication of the amount of fuel in the fuel

tank. “F” stands for full and “E” stands for

empty.

If the fuel meter indicator shows only one

segment to “E”, refill the tank as soon as

possible.

NOTE:

If the last segment blinks, it means that the

fuel is almost empty.

If the low fuel warning light (1) comes on,

fill the fuel tank immediately.

NOTE:

The activation point of the low fuel warning

light (1) varies depending on road condi-

tions (for example, slope or curve) and

driving conditions because of fuel moving

in the tank.

Refer to “Low Fuel Warning Light” in

“Warning and Indicator Lights” in this sec-

tion for details.

The mark (2) indicates that the fuel filler

door is located on the left side of the vehi-

cle.

(1)

(2)

(

)

(

)

EXAMPLE

2-53

BEFORE DRIVING

Brightness Control

68PH02203

When the ignition switch is turned to the

“ON” position, the instrument cluster lights

come on.

Your vehicle has a system to automatically

dim the brightness of the instrument panel

lights when the position lights or headlights

are on.

When the position lights and/or headlights

are ON, you can control the meter illumina-

tion intensity.

To increase the brightness of the instru-

ment panel lights, turn the brightness con-

trol knob (1) clockwise.

To reduce the brightness of the instrument

panel lights, turn the brightness control

knob (1) counterclockwise.

NOTE:

• If you do not turn the knob for more than

5 seconds while activating the bright-

ness control, the brightness control dis-

play will be canceled automatically.

• When you reconnect the battery, the

brightness of the instrument panel lights

will be reinitialized. Readjust the bright-

ness according to your preference.

Information Display

68PH02204

(1)

EXAMPLE

WARNING

If you attempt to adjust the display

while driving, you could lose control

of the vehicle.

Do not attempt to adjust the display

while driving.

(2)(1)

EXAMPLE

2-54

BEFORE DRIVING

68PH02205

(1) Trip meter selector knob

(2) Indicator selector knob

(3) Information display

When the ignition switch is in the “ON”

position, the information display shows the

following information.

Display (A)

Clock

Display (B)

Fuel gauge

Display (C)

Trip meter / Odometer / Fuel consumption /

Driving range

Display (D)

Gearshift Indicator

Clock

When the ignition switch is in the “ON”

position, the display (A) shows the time.

To change the time indication:

1) Push the trip meter selector knob (1)

and the indicator selector knob (2)

together.

2) To change the hour indication, turn the

indicator selector knob (2) left or right

repeatedly when the hour indication

blinks. To change the hour indication

quickly, turn and hold the indicator

selector knob (2). To set the hour indi-

cation, push the indicator selector knob

(2) and the minute indication will blink.

3) To change the minute indication, turn

the indicator selector knob (2) left or

right repeatedly when the minute indi-

cation blinks. To change the minute

indication quickly, turn and hold the

indicator selector knob (2). To set the

minute indication, push the indicator

selector knob (2).

NOTE:

When you reconnect the negative (–) ter-

minal to the battery, the clock indication will

be reinitialized. Change the indication

again to your preference.

Fuel Gauge

When the ignition switch is in the “ON”

position, the display (B) shows the fuel

gauge.

Refer to “Fuel Gauge” in this section.

Trip meter / Odometer / Fuel con-

sumption / Driving range

When the ignition switch is in the “ON”

position, the display (C) shows one of the

following indications, trip meter A, trip

meter B, odometer, instantaneous fuel

consumption, average fuel consumption or

driving range.

To switch the display indication (C), push

the trip meter selector knob (1) or the indi-

cator selector knob (2) quickly.

(3)

(A)

(B) (C)(D)

EXAMPLE

WARNING

If you attempt to adjust the display

while driving, you could lose control

of the vehicle.

Do not attempt to adjust the display

while driving.

2-55

BEFORE DRIVING

68PH10201

(a) Trip meter A

(b) Trip meter B

(d) Instantaneous fuel consumption

(e) Average fuel consumption

(f) Driving range

NOTE:

• Indications will change when you push

and release a knob.

• The display shows estimated values.

Indications may not be the same as

actual values.

Trip meter

The trip meter can be used to measure the

distance traveled on short trips or between

fuel stops.

You can use the trip meter A or trip meter B

independently.

To reset the trip meter to zero, push and

hold the trip meter selector knob (1) for a

while when the display shows the trip

meter.

NOTE:

The indicated maximum value of the trip

meter is 9999.9. When you run past the

maximum value, the indicated value will

return to 0.0.

Odometer

The odometer records the total distance

the vehicle has been driven.

Instantaneous fuel consumption

The display shows the value of instanta-

neous fuel consumption only when the

vehicle is moving.

NOTE:

• The display does not show the value

unless the vehicle is moving.

• For “L/100km” setting, the indicated

maximum value of instantaneous fuel

consumption is 30. No more than 30 will

be indicated on the display even if the

actual instantaneous fuel consumption is

higher.

• For “km/L” setting, the indicated maxi-

mum value of instantaneous fuel con-

Push the trip meter selector

knob (1).

Push the indicator selector

knob (2).

EXAMPLE

(a)

(b)

(c)

(d)

(e)

(f)

(

)

(

)

(

)

(

)

(

)

WARNING

If you attempt to adjust the display

while driving, you could lose control

of the vehicle.

Do not attempt to adjust the display

while driving.

NOTICE

Keep track of your odometer reading

and check the maintenance sched-

ule regularly for required services.

Increased wear or damage to certain

parts can result from failure to per-

form required services at the proper

mileage intervals.

2-56

BEFORE DRIVING

sumption is 50. No more than 50 will be

indicated on the display even if the

actual instantaneous fuel consumption is

higher.

• The indication on the display may be

delayed if fuel consumption is greatly

affected by driving conditions.

• The display shows estimated values.

Indications may not be the same as

actual values.

• You can change the units that instanta-

neous fuel consumption is displayed in.

Refer to “Average fuel consumption” in

this section.

Average fuel consumption

If you selected average fuel consumption

the last time you drove the vehicle, the dis-

play shows the last value of average fuel

consumption from previous driving when

the ignition switch is turned to the “ON”

position. Unless you reset the value of

average fuel consumption, the display indi-

cates the value of average fuel consump-

tion which includes average fuel

consumption during previous driving.

To reset the average fuel consumption to

zero, push and hold the indicator selector

knob (2) for a while when the display

shows the average fuel consumption.

NOTE:

When you reset the indication or reconnect

the negative (–) terminal to the battery, the

value of average fuel consumption will be

shown after driving for a while.

To change the unit of average fuel con-

sumption, while pushing and holding the

trip meter selector knob (1), turn the indica-

tor selector knob (2).

68PH02207

NOTE:

• When you change the units that average

fuel consumption is displayed in, the

instantaneous fuel consumption units will

be changed automatically.

• When you reconnect the negative (–)

terminal to the battery, the unit of the

average fuel consumption will be reini-

tialized. Change the unit again to your

preference.

Driving range

If you selected driving range the last time

you drove the vehicle, the display indicates

“---” for a few seconds and then indicates

the current driving range when the ignition

switch is turned to the “ON” position.

The driving range shown in the display is

the approximate distance you can drive

until the fuel gauge indicates “E”, based on

current driving conditions.

When the low fuel warning light comes on,

the display “---” will appear.

If the low fuel warning light comes on, fill

the fuel tank immediately regardless of the

value of driving range shown in the display.

As the driving range after refueling is cal-

culated based on the most recent driving

condition, the value is different each time

you refuel.

NOTE:

• If you refuel when the ignition switch is in

the “ON” position, the driving range may

not indicate the correct value.

• When you reconnect the negative (–)

terminal to the battery, the value of driv-

ing range will be shown after driving for a

while.

Gearshift Indicator

Refer to “Gearshift Indicator” in the

“OPERATING YOUR VEHICLE” section.

EXAMPLE

(Initial

setting)

2-57

BEFORE DRIVING

Setting mode

In the setting mode, you can set up the following functions.

Indication Functions

Time indication of clock “CL”

Central door locking system “d1”

Automatic door locking function “d2”

Automatic door unlocking function “d3”

2-58

BEFORE DRIVING

Additional flashes of the turn signal “L2”

Initialization setting “de-on”

Exit the setting mode “End”

Indication Functions

2-59

BEFORE DRIVING

NOTE:

Depending on vehicle’s specifications,

some items may not be displayed.

How to operate the setting mode:

1) When the ignition switch is in the “ON”

position and the vehicle is stationary,

push the trip meter selector knob (1) to

switch the information display indication

2) Push and hold the indicator selector

knob (2) until the display shows

“CLoCK”.

3) Turn and/or push the indicator selector

knob (2) to select a function that you

want to set up according to the above

chart.

4) Turn and/or push the indicator selector

knob (2) to register settings of the fol-

lowing functions.

Time indication of clock “CL”

• CL-12h: 12-hour format (default setting)

• CL-24h: 24-hour format

Central door locking system “d1”

• d1-SL1: Unlock all doors by turning the

key once

• d1-SL2: Unlock all doors by turning the

key twice (default setting)

Automatic door locking function “d2”

• d2-SL1: Disable the automatic door

locking function

• d2-SL2: Lock all doors when the vehicle

speed reaches 15 km/h

(default setting)

Automatic door unlocking

function “d3”

• d3-SL1: Disable the automatic door

unlocking function

• d3-SL3: Unlock all doors when the key

is pulled out from the ignition

switch (default setting)

Additional flashes

of the turn signal “L2”

• L2-SL1: Turn signal flashes three times

after the turn signal lever is

returned (default setting)

• L2-SL2: Disable the additional flashes

of turn signal

Initialization setting “de-on”

• de-on: Initialize all settings

68PM00272

NOTE:

• As shown in the above illustration, “SEL”

indicates on the display of currently set-

ting item.

• To go back to the higher level display

during operation, turn the indicator

selector knob (2) to display “bACK” or

“-bAC” and then push the indicator

selector knob (2).

5) To exit the setting mode, switch the dis-

play to show “End” and then push the

indicator selector knob (2).

Turn the indicator selector knob

(2).

Push the indicator selector

knob (2).

EXAMPLE

Before Driving -> Instrument Cluster (Type A) (if equipped) for Your Suzuki Baleno 4 Door Second Generation (2015-2021)

Related Topics

Popular Owner Manuals

Latest Owner Manuals