Get Before Driving -> Security System (if equipped) Guide for Suzuki Baleno 4 Door Second Generation (2015-2021)

2-15

BEFORE DRIVING

Security System (if equipped)

The security system is armed in about 5

seconds after you lock all doors (including

the tailgate) by using the keyless entry sys-

tem transmitter, keyless push start system

remote controller or request switch.

Once the system is armed, any attempt to

open a door by using any other means (*)

than the keyless entry system transmitter,

keyless push start system remote control-

ler or open the engine hood, will cause the

alarm to be triggered.

* These means include the following:

– The key

– The lock knob on a door

– The central door locking switch

– The tailgate emergency lever

Also, in case that you have set the shock

sensor to enabled state and set sensitivity

of the pre-warning function and full blast

warning function to a level other than 0, the

alarm will be triggered if any attempt to

tamper with the vehicle. The shock sensor

can be selected enabled or disabled state,

and sensitivity of each warning can be

adjusted as desired. To set the shock sen-

sor, ask your authorised Maruti Suzuki

workshop or use the setting mode of the

information display.

NOTE:

• The default setting of the shock sensor

is in the disabled state. Set to the

enabled state and adjust sensitivity of

each warning according to your prefer-

ence. For details on how to use the infor-

mation display, refer to “Information

Display” in this section.

• Your dealer may have already set the

shock sensor of the vehicle to the

enabled state before you purchase it.

Consult your dealer for further informa-

tion.

NOTE:

• The security system generates alarms

when any of the predetermined condi-

tions is met. However, the system does

not have any function of blocking unau-

thorized entry into the vehicle.

• Always use the keyless entry system

transmitter or keyless push start system

remote controller to unlock the doors when

the security system has been armed.

Using a key instead will trigger the alarm.

• If a person who does not know the secu-

rity system is going to drive the vehicle,

we recommend you explain the system

and its operation to the person, or dis-

able the system beforehand. Mistakenly

triggering the alarm may cause a nui-

sance to others.

• Even if the security system is armed,

you should still be careful to guard

against theft. Do not leave money or

things of value in the vehicle.

How to arm the security system

(when enabled)

Lock all doors (including the tailgate) using

the keyless entry system transmitter or

keyless push start system remote control-

ler. The security system indicator (1) will

start blinking rapidly, and the security sys-

tem will be armed in about 5 seconds.

While the system is being armed, the indi-

cator continues to blink at intervals of

approximately 2 seconds.

68PH00218

(1)

EXAMPLE

2-16

BEFORE DRIVING

NOTE:

• To prevent the alarm from being acci-

dentally triggered, avoid arming it while

anyone remains inside the vehicle. The

alarm will be triggered if any person

inside opens the door, tailgate, engine

hood, or swings the vehicle (if the shock

sensor is in the enabled state).

• The security system is not armed when

all doors are locked using the key from

outside, using the door lock knobs or the

central door locking switch from inside.

• If any door is not operated within approx-

imately 30 seconds after the doors have

been unlocked using the keyless entry

system transmitter or keyless push start

system remote controller, the doors are

automatically locked again. When the

doors are locked, the security system

will be armed in about 5 seconds if the

system is in the enabled state.

• If the security system indicator (1) blinks

when the ignition switch is in the “ON”

position or the ignition mode is “ON”,

there may be something wrong with the

security system. Ask your authorised

Maruti Suzuki workshop to inspect the

system.

How to disarm the security system

Simply unlock the doors using the keyless

push start system remote controller, the

request switch or the keyless entry system

transmitter. The security system indicator

will go out, indicating that the security sys-

tem is disarmed.

How to stop the alarm

Should the alarm be triggered accidentally,

the alarm will stop by the following opera-

tions.

• Press the engine switch to change the

ignition mode to “ON” or turn the ignition

switch to “ON” position.

• Unlock the doors using the keyless push

start system remote controller, the

request switch, or the keyless entry sys-

tem transmitter.

NOTE:

• Even after the alarm has stopped, if you

lock the doors using the keyless entry

system transmitter or keyless push start

system remote controller, the security

system will be rearmed with a delay of

about 5 seconds.

• If you disconnect the battery while the

security system is in the armed condition

or the alarm is actually in operation, the

alarm will be re-triggered when the bat-

tery is then reconnected.

• Even after the alarm has stopped at the

end of the predetermined operation time,

it will be triggered again if any of the

doors, tailgate or engine hood is opened,

or the vehicle feels a shock (if the shock

sensor is in the enabled state), without

disarming the security system.

Checking whether the alarm has been

triggered during parking

If the alarm was triggered and you then

turn the ignition switch to “ON” position or

the ignition mode is “ON”, the security sys-

tem indicator will blink rapidly for about 8

seconds and a buzzer will beep 4 times

during this period. If this happens, check

whether the vehicle has been broken into

while you were away from it.

Enabling and disabling the security

system

The security system can be either enabled

or disabled.

2-17

BEFORE DRIVING

When enabled

• If any of the doors or tailgate are opened

without unlocking by the keyless entry

system transmitter or keyless push start

system remote controller, all turn signal

lights start to blink and the interior

buzzer beeps intermittently. After 5 sec-

onds, the siren will sound for about 27.5

seconds. The security system indicator

continues to blink during this time.

• If the engine hood is opened, all turn sig-

nal lights blink, and the siren sounds for

about 27.5 seconds. The security sys-

tem indicator continues to blink during

this time.

(If the shock sensor is in the enabled state)

• If the vehicle feels a shock higher than

the pre-warning sensitivity, the siren

sounds for about 2 seconds (pre-warn-

ing). If the vehicle feel a shock higher

than the full blast warning sensitivity, all

turn signal lights start to blink and the

interior buzzer beeps intermittently. After

5 seconds, the siren will sound for about

27.5 seconds (full blast warning). The

security system indicator continues to

blink during this time.

NOTE:

If you set the full blast warning sensitivity

higher than the pre-warning sensitivity in

the setting mode of the information display,

or the vehicle feels such shock as to be

able to trigger the full blast warning, the full

blast warning will be triggered preferen-

tially. In this case, the pre-warning will not

be triggered.

When disabled

When the system is disabled, it stays dis-

armed even if you perform any system

arming operation.

How to switch the state of the security

system

When the security system has been

already disarmed, you can switch the sys-

tem from the enabled state to the disabled

state, and vice versa, using the following

method.

1) Sit in the driver’s seat and make sure

that all doors, tailgate and engine hood

are closed.

•If any door is open, the open door

warning light comes on.

68PH00219

2) (Vehicle with keyless push start sys-

tem only)

Turn the lock knob (1) on the driver’s

door rearward (2).

68PH00220

(1)

(2)

EXAMPLE

(3)

EXAMPLE

2-18

BEFORE DRIVING

3) Turn the knob on the lighting control

lever to the OFF position (3).

NOTE:

The following steps 4) and 5) must be

completed within 15 seconds.

68PH00221

4) Turn the knob on the lighting control

lever to the position and then turn

back to the OFF position. Repeat this

operation 4 times.

68PH00222

5) Push the lock end (4) (forward end) of

the central door locking switch (5), and

then push the unlock end (6) (backward

end). Repeat this operation 3 times.

Every time you perform the series of the

above steps, the state of the security sys-

tem changes from the currently selected

one to the other. You can check whether

the system is enabled or disabled by the

number of interior buzzer beeps at the end

of the procedure as follows.

• If you cannot complete the operations in

step 4) and 5) within 15 seconds cor-

rectly, the state of the security system

will not change and the interior buzzer

does not beep. Perform the procedure

again from the beginning.

NOTE:

You can also switch the security system

from the enabled state to the disabled

state, and vice versa, via the setting mode

of the information display. For details on

how to use the information display, refer to

“Information Display” in this section.

OFF

4 times

EXAMPLE

(4)

(5)

(6)

EXAMPLE

3 times

System state Number of beeps

Disabled

Once

Enabled 4 times

Before Driving -> Security System (if equipped) for Your Suzuki Baleno 4 Door Second Generation (2015-2021)

Related Topics

Popular Owner Manuals

Latest Owner Manuals