2015-2021 Suzuki Baleno 4 Door Before Driving -> Keyless Push Start System Remote Controller / Keyless Entry System Transmitter User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Before Driving -> Keyless Push Start System Remote Controller / Keyless Entry System Transmitter for Your Suzuki Baleno 4 Door Second Generation (2015-2021)

2-5
BEFORE DRIVING
If you cannot unlatch the tailgate by push-
ing the unlatch switch (1) due to a dis-
charged battery or malfunction, follow the
procedures below to unlatch the tailgate
from inside the vehicle.
1) Remove the luggage compartment
cover and fold the rear seat forward for
easier access. Refer to “Folding Rear
Seats” section for details on how to fold
the rear seat forward.
2) To approach the emergency lever,
remove the trim of the tailgate.
68PH00207
3) Open the cover (2), and then, move the
emergency lever (3) to the direction of
the arrow with a flat blade screwdriver
as shown in the illustration.
4) Push open the tailgate from inside. The
tailgate will be latched again by simply
closing the tailgate.
If the tailgate cannot be unlatched by push-
ing the unlatch switch (1), have the vehicle
inspected by your authorised Maruti
Suzuki workshop.
Keyless Push Start System
Remote Controller/Keyless
Entry System Transmitter
68PH00270
Your vehicle is equipped with either a key-
less push start system remote controller
(Type A) or a keyless entry system trans-
mitter (Type B). The remote controller has
a keyless entry system and a keyless push
start system. The transmitter has only a
keyless entry system. For details, refer to
the following explanations.
WARNING
Always make sure that the tailgate is
closed and latched securely. Com-
pletely closing the tailgate helps pre-
vent occupants from being thrown
from the vehicle in the event of an
accident. Completely closing it also
helps keep exhaust gases from enter-
ing the vehicle.
CAUTION
Make sure there is no one near the
tailgate when pushing open the tail-
gate from inside the vehicle.
(2)
(3)
Type A Type B
2-6
BEFORE DRIVING
Keyless Push Start System Remote
Controller (Type A)
The remote controller enables the follow-
ing operations:
• You can lock or unlock the doors by
operating the LOCK/UNLOCK buttons
on the remote controller. Refer to the
explanation in this section.
• You can lock or unlock the doors by
pushing the request switch. For details,
refer to the explanation in this section.
• You can start the engine without using
an ignition key. For details, refer to
“Engine Switch” in the “OPERATING
YOUR VEHICLE” section.
68PH00208
(1) “LOCK” button
(2) “UNLOCK” button
You can lock or unlock all doors (including
the tailgate) simultaneously by operating
the remote controller near the vehicle.
WARNING
Radio waves from the keyless push
start system antenna(s) may interfere
with operation of electrical medical
equipment such as pacemakers. Fail-
ure to take the precautions listed
below can increase the risk of severe
injury or death due to radio wave
interference.
• Anyone who uses electrical medi-
cal equipment such as a pace-
maker should consult the medical
equipment supplier or their medical
advisor about whether radio waves
from the antenna(s) can interfere
with the medical equipment.
• If radio wave interference is a con-
cern, have the function of the
antenna(s) disabled by your autho-
rised Maruti Suzuki workshop.
(1)
(2)
2-7
BEFORE DRIVING
Central door locking system
• To lock all doors, push the “LOCK” but-
ton (1) once.
• To unlock only the driver’s door, push the
“UNLOCK” button (2) once.
• To unlock other doors, push the
“UNLOCK” button (2) once again.
NOTE:
You can switch the function that unlocks all
doors from twice operations to once opera-
tion, and vice versa, via the setting mode
of the information display. For details on
how to use the information display, refer to
“Information Display” in this section.
The turn signal lights will flash once and
the siren will sound once when the doors
are locked.
When the doors are unlocked:
• The turn signal lights will flash twice and
the siren will sound twice.
• If the interior light switch is in the
“DOOR” position, the interior light will
turn on for about 15 seconds and then
fade out. If you press the engine switch
during this time, the light will start to fade
out immediately.
Be sure the doors are locked after you
operate the “LOCK” button (1).
If no door is opened within about 30 sec-
onds after the “UNLOCK” button (2) is
operated, the doors will automatically lock
again.
Panic alarm function
This function is to get the attention of oth-
ers.
Push both of the “LOCK” button (1) and
“UNLOCK” button (2) for more than 3 sec-
onds.
The turn signal lights will blink for about
27.5 seconds. Also, the siren will sound for
about 27.5 seconds at the same time.
To cancel the panic alarm, press any but-
ton (LOCK or UNLOCK).
You can also cancel the panic alarm in any
of the following operations.
• Press the engine switch to change the
ignition mode to ON.
• Bring the remote controller with you and
press the request switch.
NOTE:
The panic alarm function will not activate
when the ignition mode is “ACC” or “ON”.
NOTE:
• If you lock the doors using the remote
controller when the engine hood are
open, the siren will sound 3 times to
remind you.
• If the security system was triggered due
to an unauthorized entry into the vehicle
and then you unlock the doors using the
remote controller, the siren will sound 4
times to remind you. If this happens,
check whether your vehicle has been
broken into while you were away from it.
• Once you push both of the “LOCK” but-
ton (1) and “UNLOCK” button (2), then
you push one of the buttons within 5 sec-
onds, the siren will not sound. However,
If you push one of the buttons twice
within 5 seconds, or push one of the but-
tons 5 seconds later, the siren will
sound.
• You can set whether the siren sounds
when locking or unlocking the door(s) via
the setting mode of the information dis-
play. For details on how to use the infor-
mation display, refer to “Information
Display” in this section.
2-8
BEFORE DRIVING
NOTE:
• The maximum operating distance of the
remote controller is about 5 m (16 ft.),
but this can vary depending on the sur-
roundings, especially near other trans-
mitting devices such as radio towers or
CB (Citizen’s Band) radios.
• The door locks cannot be operated with
the remote controller if the ignition mode
is other than the “LOCK” (OFF).
• If any door is open, you cannot lock the
door by operating the remote controller,
however unlock the door.
• If you lose one of the remote controllers,
ask your authorised Maruti Suzuki work-
shop as soon as possible for a replace-
ment. Be sure to have your dealer
program the new remote controller code
in your vehicle’s memory so that the old
code is erased.
Keyless unlocking/locking using the
request switches
68PH00209
When the remote controller is within the
operating range described in this section,
you can lock or unlock the doors (including
the tailgate) by pushing the request switch
(1) on the driver’s door handle, front pas-
senger’s door handle or tailgate.
To lock all doors when all doors are
unlocked:
• To lock all doors, push one of the
request switches once.
The turn signal lights will flash once and
the exterior siren will sound once when the
doors are locked.
To unlock a door or all doors:
• Push one of the request switches once
to unlock only one door.
• Push one of the request switches twice
to unlock all doors.
NOTE:
You can switch the function that unlocks all
doors from twice operations to once opera-
tion, and vice versa, via the setting mode
of the information display. For details on
how to use the information display, refer to
“Information Display” in this section.
When the doors are unlocked:
• The turn signal lights will flash twice and
the exterior siren will sound twice.
• If the interior light switch is in the
“DOOR” position, the interior light will
turn on for about 15 seconds and then
fade out. If you press the engine switch
during this time, the light will start to fade
out immediately.
Be sure the doors are locked after you
operate the request switch to lock the
doors.
(1)
EXAMPLE
2-9
BEFORE DRIVING
NOTE:
• The door locks cannot be operated by
the request switch under the following
conditions:
– If any door is open or is not completely
closed.
– If the ignition mode is other than
“LOCK” (OFF).
• If no doors are opened within about 30
seconds after unlocking the doors by
pushing the request switch, the doors
will be locked again automatically.
68PH00210
(1) 80 cm (2 1/2 feet)
When the remote controller is within
approximately 80 cm (2 1/2 feet) from a
front door handle or the tailgate switch, you
can lock or unlock the doors by pushing
the request switch.
NOTE:
• If the remote controller is outside the
request switch operating range
described above, you will not be able to
operate the request switch.
• If the battery of the remote controller
runs down or there are strong radio
waves or noise, the request switch oper-
ating range may be reduced or the
remote controller may be inoperative.
• If the remote controller is too close to the
door glass, the request switches may not
operate.
• If a spare remote controller is in the vehi-
cle, the request switches may not oper-
ate normally.
• The remote controller will only operate a
request switch if it is within the switch’s
operating range. For example, if the
remote controller is within the operating
range of the driver’s door request switch
but not the front passenger’s door
request switch or the tailgate request
switch, the driver’s door switch can be
operated but the front passenger’s door
switch or tailgate switch cannot be oper-
ated.
NOTE:
The keyless push start system may not
function correctly in certain environments
or under certain operating conditions such
as the following:
• When there are strong signals coming
from a television, power station or a cel-
lular phone.
• When the remote controller is in contact
with or covered by a metal object.
• When a radio wave type remote keyless
entry is used nearby.
• When the remote controller is placed
near an electronic device such as per-
sonal computer.
Some additional precautions you should
take and information you should be aware
of are:
• Make sure the key is stowed in the
remote controller. If the remote controller
becomes unreliable, you will not be able
to lock or unlock the doors.
(1)
(1)
(1)
EXAMPLE
NOTICE
The remote controller is a sensitive
electronic instrument. To avoid dam-
aging the remote controller:
• Do not expose it to impacts, mois-
ture or high temperature such as
by leaving it on the dashboard
under direct sunlight.
• Keep the remote controller away
from magnetic objects such as a
television.
2-10
BEFORE DRIVING
• Be sure that the driver always carries the
remote controller.
• If you lose one of the remote controllers,
ask your authorised Maruti Suzuki work-
shop as soon as possible for a replace-
ment. Be sure to have your dealer
program the new remote controller code
in your vehicle’s memory so that the old
code is erased.
• You can use up to four remote control-
lers and the keys for your vehicle. Ask
your authorised Maruti Suzuki workshop
for details.
• The battery life of the remote controller
is about two years, but it can vary
depending on usage conditions.
68PH00211
To stow the key into the remote controller,
push the key in the remote controller until
you hear a click.
68PH00212
To remove the key from the remote control-
ler, push the button (A) in the direction of
the arrow and pull the key out from the
remote controller.
Request switch warning buzzer
This exterior buzzer beeps for about 2 sec-
onds in the following conditions to warn
you that the request switch is not working:
• The request switch is pressed after all
doors are closed with the ignition mode
changed to “ACC” or “ON” by pressing
the engine switch.
• The request switch is pressed in any of
the following conditions after changing
the ignition mode to “LOCK” (OFF) by
pressing the engine switch.
– The remote controller is left inside the
vehicle.
– Any door (including the tailgate) is
open.
Press the request switch again after doing
the following:
With the ignition mode changed to “LOCK”
(OFF) by pressing the engine switch, bring
out the remote controller if it is inside the
vehicle and check that all doors are com-
pletely closed.
Reminder function
68PH00213
If the remote controller is not in the vehicle
under the following conditions, the buzzer
sounds intermittently for about 2 seconds
and the immobilizer/keyless push start sys-
tem warning light on the instrument cluster
blinks:
When one or more doors are opened and
all of the doors are later closed with the
ignition mode is other than “LOCK”.
(A)
EXAMPLE
2-11
BEFORE DRIVING
The indicator light will turn off within sev-
eral seconds after the remote controller is
returned to an area of the vehicle other
than the rear luggage area.
If the remote controller is left in the vehicle
and you lock the driver’s door or front pas-
senger’s door as described below, the door
will be automatically unlocked.
• If you open the driver’s door and lock the
door by turning the lock knob forward or
pushing the power door locking switch,
the driver’s door will be automatically
unlocked.
• If you open the front passenger’s door
and lock the door by turning the lock
knob forward or pushing the power door
locking switch, the front passenger’s
door will be automatically unlocked.
NOTE:
• The reminder will not operate when the
remote controller is on the instrument
panel, in the glove box, in a storage
compartment, in the sun visor or on the
floor etc.
• Be sure that the driver always carries the
remote controller.
• Do not leave the remote controller in the
vehicle when leaving the vehicle.
Replacement of the battery
If the remote controller becomes unreli-
able, replace the battery.
To replace the battery of the remote con-
troller:
71LMT0201
1) Pull the key out from the remote con-
troller.
2) Insert a flat blade screwdriver covered
with a soft cloth in the slot of the remote
controller and pry it open.
68PH00214
(1) Lithium disc type battery:
CR2032 or equivalent
3) Replace the battery (1) so its + terminal
faces the bottom of the case as shown
in the illustration.
4) Close the remote controller firmly.
5) Make sure the door locks can be oper-
ated with the remote controller.
6) Dispose of the used battery properly
according to applicable rules or regula-
tions. Do not dispose of lithium batter-
ies with ordinary household trash.
(1)
2-12
BEFORE DRIVING
NOTE:
Used batteries must be disposed properly
according to applicable rules or regulations
and must not be disposed with ordinary
household trash.
Keyless Entry System Transmitter
(Type B)
68PH00215
(1) “LOCK” button
(2) “UNLOCK” button
You can lock or unlock all doors (including
the tailgate) simultaneously by operating
the transmitter near the vehicle.
Central door locking system
• To lock all doors, push the “LOCK” but-
ton (1) once.
• To unlock only the driver’s door, push the
“UNLOCK” button (2) once.
• To unlock other doors, push the
“UNLOCK” button (2) once again.
NOTE:
You can switch the function that unlocks all
doors from twice operations to once opera-
tion, and vice versa, via the setting mode
of the information display. For details on
how to use the information display, refer to
“Information Display” in this section.
The turn signal lights will flash once and
the siren will sound once when the doors
are locked.
When the doors are unlocked:
• The turn signal lights will flash twice and
the siren will sound twice.
• If the interior light switch is in the
“DOOR” position, the interior light will
turn on for about 15 seconds and then
fade out. If you insert the key into the
ignition switch during this time, the light
will start to fade out immediately.
Be sure the doors are locked after you
operate the “LOCK” button (1). If no door is
opened within about 30 seconds after the
“UNLOCK” button (2) is operated, the
doors will automatically lock again.
WARNING
Swallowing a lithium battery may
cause serious internal injury. Do not
allow anyone to swallow a lithium
battery. Keep lithium batteries away
from children and pets. If swallowed,
contact a physician immediately.
NOTICE
The remote controller is a sensitive
electronic instrument. To avoid dam-
aging it, do not expose it to dust or
moisture or tamper with internal parts.
(1)
(2)
2-13
BEFORE DRIVING
NOTE:
• If you lock the doors using the transmit-
ter when the engine hood is open, the
siren will sound 3 times to remind you.
• If the security system was triggered due
to an unauthorized entry into the vehicle
and then you unlock the doors using the
transmitter, the siren will sound 4 times
to remind you. If this happens, check
whether your vehicle has been broken
into while you were away from it.
• Once you push both of the “LOCK” but-
ton (1) and “UNLOCK” button (2), then
you push one of the buttons within 5 sec-
onds, the siren will not sound. However,
If you push one of the buttons twice
within 5 seconds, or push one of the but-
tons 5 seconds later, the siren will
sound.
• You can set whether the siren sounds
when locking or unlocking the door(s) via
the setting mode of the information dis-
play. For details on how to use the infor-
mation display, refer to “Information
Display” in this section.
NOTE:
• The maximum operating distance of the
keyless entry system transmitter is about
5 m (16 ft.), but this can vary depending
on the surroundings, especially near
other transmitting devices such as radio
towers or CB (Citizen’s Band) radios.
• The door locks cannot be operated with
the transmitter, if the ignition key is
inserted in the ignition switch.
• If any door is open, you cannot lock the
door by operating the transmitter, how-
ever unlock the door.
• If you lose one of the transmitters, ask
your authorised Maruti Suzuki workshop
as soon as possible for a replacement.
Be sure to have your dealer program the
new transmitter code in your vehicle’s
memory so that the old code is erased.
Panic alarm function
This function is to get the attention of oth-
ers.
Push both of the “LOCK” button (1) and
“UNLOCK” button (2) for more than 3 sec-
onds.
The turn signal lights will blink for about
27.5 seconds. Also, the siren will sound for
about 27.5 seconds at the same time.
To cancel the panic alarm, press any but-
ton (LOCK or UNLOCK). You can also turn
the ignition switch to the “ON” position to
cancel the panic alarm.
NOTE:
The panic alarm function will not activate
when the key is in the ignition switch.
NOTICE
The transmitter is a sensitive elec-
tronic instrument. To avoid damaging
the transmitter:
• Do not expose it to impacts, mois-
ture or high temperature such as
by leaving it on the dashboard
under direct sunlight.
• Keep the transmitter away from
magnetic objects such as a televi-
sion.
2-14
BEFORE DRIVING
Replacement of the battery
If the transmitter becomes unreliable,
replace the battery.
To replace the battery of the transmitter:
68PH00216
1) Remove the screw (1), and open the
transmitter cover.
2) Remove the transmitter (2).
68PH00217
(3) Lithium disc type battery:
CR1616 or equivalent
3) Put the edge of a flat blade screwdriver
in the slot of the transmitter (2) and pry
it open.
4) Replace the battery (3) so its + terminal
faces the “+” mark of the transmitter.
5) Close the transmitter and install it into
the transmitter holder.
6) Close the transmitter cover, install and
tighten the screw (1).
7) Make sure the door locks can be oper-
ated with the transmitter.
8) Dispose of the used battery properly
according to applicable rules or regula-
tions. Do not dispose of lithium batter-
ies with ordinary household trash.
NOTE:
Used batteries must be disposed properly
according to applicable rules or regulations
and must not be disposed with ordinary
household trash.
(1)
(2)
(2)
(3)
WARNING
Swallowing a lithium battery may
cause serious internal injury. Do not
allow anyone to swallow a lithium
battery. Keep lithium batteries away
from children and pets. If swallowed,
contact a physician immediately.
NOTICE
The transmitter is a sensitive elec-
tronic instrument. To avoid damaging
it, do not expose it to dust or mois-
ture or tamper with internal parts.

Related Topics

Popular Owner Manuals