2015-2021 Suzuki Baleno 4 Door Before Driving -> Instrument Cluster (Type C) (if equipped) User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Before Driving -> Instrument Cluster (Type C) (if equipped) for Your Suzuki Baleno 4 Door Second Generation (2015-2021)

2-72
BEFORE DRIVING
1. Speedometer
2. Tachometer
3. Fuel gauge
4. Temperature gauge
5. Information display
6. Trip meter selector knob
7. Indicator selector knob
8. Warning and indicator lights
68PH02222
34 886 75
1
2 8
3
4
8
8
6
7
5
2
8
EXAMPLE
Instrument Cluster (Type C) (if equipped)
2-73
BEFORE DRIVING
Speedometer
The speedometer indicates vehicle speed.
Tachometer
The tachometer indicates engine speed in
revolutions per minute.
Fuel Gauge
68PH02223
When the ignition mode is “ON”, this
gauge gives an approximate indication of
the amount of fuel in the fuel tank. “F”
stands for full and “E” stands for empty.
If the indicator approaches a low level
(near “E”) on fuel gauge, refill the tank as
soon as possible.
NOTE:
The indicator moves a little depending on
road conditions (for example, slope or
curve) and driving conditions because of
fuel moving in the tank.
If the low fuel warning light (1) comes on,
fill the fuel tank immediately.
Refer to “Low fuel warning light” in “Warn-
ing and indicator lights” in this section for
details.
The mark (2) indicates that the fuel filler
door is located on the left side of the vehi-
cle.
NOTICE
Never drive the vehicle with the
engine revving in the red zone or
severe engine damage can result.
Keep the engine speed below the red
zone even when downshifting to a
lower gear position.
Refer to “Downshifting maximum
allowable speeds” in “OPERATING
YOUR VEHICLE” section.
(1)
(2)
(
1
)
(
2
)
EXAMPLE
2-74
BEFORE DRIVING
Temperature Gauge
68PH02224
When the ignition mode is “ON”, this
gauge indicates the engine coolant tem-
perature. Under normal driving conditions,
the indicator should stay within the normal,
acceptable temperature range between
“H” and “C”. If the indicator approaches
“H”, overheating is indicated. Follow the
instructions for “Engine trouble: Overheat-
ing” in “EMERGENCY SERVICE” section.
Brightness Control
68PH02225
When the engine switch is pressed to
change the ignition mode to “ON”, the
instrument cluster lights come on.
Your vehicle has a system to automatically
dim the brightness of the instrument clus-
ter lights when the position lights or head-
lights are on.
You can change the brightness of the
instrument cluster lights regardless of
whether the position lights or headlights
are off or on.
To increase the brightness of the instru-
ment cluster lights, turn the indicator selec-
tor knob (1) clockwise.
To reduce the brightness of the instrument
cluster lights, turn the indicator selector
knob (1) counterclockwise.
NOTE:
• If you do not turn the knob for more than
5 seconds while activating the bright-
ness control, the brightness control dis-
play will be canceled automatically.
• When you reconnect the battery, the
brightness of the instrument cluster
lights will be reinitialized. Readjust the
brightness according to your preference.
NOTE:
If you select the maximum brightness level
when the position lights or headlights are
on, the following functions will be can-
celled.
• The function which automatically dims
the brightness of instrument cluster
lights
• The function which operates with the
brightness control, except maximum
brightness level
NOTICE
Continuing to drive the vehicle when
engine overheating is indicated can
result in severe engine damage.
EXAMPLE
(1)
(
1
)
EXAMPLE
WARNING
Do not adjust the brightness of the
instrument panel lights while driving.
Otherwise, you could lose control of
the vehicle.
2-75
BEFORE DRIVING
Information Display
The information display is shown when the
ignition mode is “ON”.
68PH02226
(1) Information display
68PM00253
(2) Indicator selector knob
(3) Trip meter selector knob
The information display shows the follow-
ing information.
Display (A)
Clock
Display (B)
Thermometer
Display (C)
Warning and indicator messages /
Fuel consumption / Driving range /
Average speed / Driving time /
Clock and date / Torque and power
Display (D)
Gearshift indicator
Display (E)
Trip meter
Display (F)
Odometer
68PH02228
When the engine switch is pressed to
change the ignition mode to “ON”, the
clock display shown in the above illustra-
tion will appear on the display for several
seconds.
Some warning and indicator messages
may appear on the display when the igni-
tion mode is “ACC” or “LOCK” (OFF).
(1)
(A) (B)
(C)
(D)
(E)
(F)
(
1
)
(
A
)
(
B
)
(
C
)
(
D
)
(
E
)
(
F
)
( )
(2)(3)
(
2
)
(
3
)
EXAMPLE
EXAMPLE
2-76
BEFORE DRIVING
Clock
The display (A) shows the time.
To set the clock, follow “Setting mode”
instructions in this section.
Thermometer
The display (B) shows the thermometer.
The thermometer indicates the outside
temperature.
68PH02229
If the outside temperature nears freezing,
the message shown in the above illustra-
tion will appear on the display.
NOTE:
The outside temperature indication is not
the actual outside temperature when driv-
ing at low speed, or when stopped.
Fuel consumption / Driving range /
Average speed / Driving time
Clock and date / Torque and power
When there are no warning or indicator
messages on the display (C), you can
select one of the following indications to
appear on the display: instantaneous fuel
consumption, average fuel consumption,
driving range, average speed, driving time,
clock and date, torque and power or no
indication.
WARNING
If you attempt to adjust the display
while driving, you could lose control
of the vehicle.
do not attempt to adjust the display
while driving.
2-77
BEFORE DRIVING
(a) Instantaneous fuel consumption / Average fuel consumption / Driving range
(b) Instantaneous fuel consumption / Average fuel consumption / 5 minute average fuel
consumption
(c) Average speed / 5 minute average speed / Driving time
(d) Clock and date
(e) Torque and Power
(f) No indication
(a) (b) (c)
(f) (e) (d)
(
a
)
(
b
)
(
c
)
(f)
(
e
)
(
d
)
EXAMPLE
To switch the display indication, push the
indicator selector knob (2) quickly.
NOTE:
The value of instantaneous fuel consump-
tion, average fuel consumption, driving
range, average speed and torque and
power shown on the display are affected
by the following conditions;
• road condition
• surrounding traffic condition
• driving condition
• vehicle condition
• a malfunction which causes the malfunc-
tion indicator light to come on or blink
2-78
BEFORE DRIVING
Instantaneous fuel consumption
The display shows instantaneous fuel con-
sumption with a bar graph only when the
vehicle is moving.
68PM00280
(4) Instantaneous fuel consumption
NOTE:
• The display does not show the bar graph
unless the vehicle is moving.
• For “L/100km” setting, the indicated
maximum value of instantaneous fuel
consumption is 30. No more than 30 will
be indicated on the display even if the
actual instantaneous fuel consumption is
higher.
• For “km/L” setting, the indicated maxi-
mum value of value of instantaneous
fuel consumption is 50. No more than 50
will be indicated on the display even if
the actual instantaneous fuel consump-
tion is higher.
• For “MPG(UK)” setting, the indicated
maximum value of instantaneous fuel
consumption is 80. No more than 80 will
be indicated on the display even if the
actual instantaneous fuel consumption is
higher.
• For “MPG(US)” setting, the indicated
maximum value of instantaneous fuel
consumption is 60. No more than 60 will
be indicated on the display even if the
actual instantaneous fuel consumption is
higher.
• The indication on the display may be
delayed if fuel consumption is greatly
affected by driving conditions.
• The display shows estimated values.
Indications may not be the same as
actual values.
Average fuel consumption / 5-minute
average fuel consumption
Average fuel consumption from previous
reset and 5-minute average fuel consump-
tion are shown.
(Average fuel consumption)
68PM00281
(5) Average fuel consumption
If you selected average fuel consumption
the last time you drove the vehicle, the dis-
play shows the last value of average fuel
consumption from previous driving when
the engine switch is pressed to change the
ignition mode to “ON”. Unless you reset
the value of average fuel consumption, the
display indicates the value of average fuel
consumption based on the average fuel
consumption during previous driving.
NOTE:
When you reconnect the negative (–) ter-
minal to the battery, the value of average
fuel consumption will be shown after driv-
ing for a period of time.
(4)
(
4
)
EXAMPLE
(5)
(5)
(
5
)
(
5
)
EXAMPLE
2-79
BEFORE DRIVING
You can select when the value of average
fuel consumption is reset from among the
following two methods;
• Reset after refuel: the value of average
fuel consumption will be reset automati-
cally by refueling.
• Reset with trip meter A: the value of
average fuel consumption will be reset
automatically by resetting trip meter A.
To change when the value of average fuel
consumption is reset, refer to “Setting
mode” in this section.
NOTE:
• If you add only a small amount of fuel
when you select “Reset after refuel”, the
average fuel consumption value may not
be reset.
• Display option (b) shows the fuel con-
sumption history below current instanta-
neous fuel consumption. History display
portion is updated to show fuel con-
sumption history every 5 minutes (till
past 15 minutes) or every driving cycle
(till past 3 driving cycle) depending on
which mode is selected in setting mode.
(5-minute average fuel consumption)
68PM00282
(6) 5-minute average fuel consumption
You can check transition of 5-minute aver-
age fuel consumption every 5 minutes
from 15 minutes before up to now. Time
indication and driving cycle indication can
be changed. For details, refer to “Setting
mode” in this section.
Driving range
68PM00283
(7) Driving range
If you selected driving range the last time
you drove the vehicle, the display indicates
“---” for a few seconds and then indicates
the current driving range when engine
switch is pressed to change the ignition
mode to “ON”.
The driving range shown in the display is
the approximate distance you can drive
until the fuel gauge indicates “E”, based on
current driving conditions.
When the low fuel warning light comes on,
the display “---” will appear.
If the low fuel warning light comes on, fill
the fuel tank immediately regardless of the
value of driving range shown in the display.
As the driving range after refueling is cal-
culated based on the most recent driving
(6)
(
6
)
EXAMPLE
(7)
(
7
)
EXAMPLE
2-80
BEFORE DRIVING
condition, the value is different each time
you refuel.
NOTE:
• If you refuel when the ignition mode is
“ON”, the driving range may not indicate
the correct value.
• When you reconnect the negative (–)
terminal to the battery, the value of driv-
ing range will be shown after driving for a
period of time.
Average Speed / 5- minute average
speed
Average speed from previous reset and 5-
minute average speed are shown.
(Average Speed)
68PM00284
(8) Average speed
If you selected average speed the last time
you drove the vehicle, the display indicates
the last value of average speed from previ-
ous driving when the engine switch is
pressed to change the ignition mode to
“ON”. Unless you reset the value of aver-
age speed, the display indicates the value
of average speed which includes average
speed during previous driving.
To reset the value of average speed, push
and hold the indicator selector knob (2) for
about 2 seconds when the display indi-
cates an average speed. The display
shows “---” and then indicates a new aver-
age speed after driving for a short time.
NOTE:
• When you reconnect the negative (–)
terminal to the battery, the value of aver-
age speed will be shown after driving for
a period of time.
• Display (c) shows current average
speed and average speed history. His-
tory display portion is below current
average speed and is updated every 5
minutes (till past 10 minutes).
(5-minute average speed)
68PM00285
(9) 5-minute average speed
You can check transition of 5-minute aver-
age speed every 5 minutes from 10 min-
utes before up to now.
(8)
(
8
)
EXAMPLE
(9)
(
9
)
EXAMPLE
2-81
BEFORE DRIVING
Driving time
68PM00286
(10) Driving time
Driving time from previous reset is shown.
To reset the driving time, push and hold the
indicator selector knob (2) for about 2 sec-
onds when the display indicates a driving
time. The display shows “---” and then indi-
cates a new driving time after driving for a
short time.
NOTE:
Disconnection of the battery negative (-)
terminal will reset the indication of the driv-
ing time.
Clock and date
Date and time are shown. For the setting
procedure, refer to “Setting mode” in this
section.
Torque and Power
Present engine torque and power are
shown.
Information of after driving
When you press the engine switch to
change the ignition mode to “LOCK”
(OFF), the following information appears
for several seconds on the information dis-
play.
68PS00214
Torque and Power display
Display (e) shows Torque and Power
graphs at various vehicle condition.
This figure is for reference only and indica-
tion may not be same as actual value.
Gearshift Indicator
The display (D) shows some of the follow-
ing indications.
Refer to “Gearshift Indicator” in the
“OPERATING YOUR VEHICLE” section.
Trip meter
The display (E) shows the trip meter.
The trip meter can be used to measure the
distance traveled on short trips or between
fuel stops.
You can use trip meter A or trip meter B
independently.
To reset the trip meter to zero, push and
hold the trip meter selector knob (3) for
about 2 seconds when the display shows
the trip meter.
Odometer
The display (F) shows the odometer.
The odometer records the total distance
the vehicle has been driven.
(10)
(
10
)
EXAMPLE
EXAMPLE
NOTICE
Keep track of your odometer reading
and check the maintenance sched-
ule regularly for required services.
Increased wear or damage to certain
parts can result from failure to per-
form required services at the proper
mileage intervals.
2-82
BEFORE DRIVING
Setting mode
When the ignition mode is “ON” and the
vehicle is stationary, you can enter the set-
ting mode of the information display by
pushing and holding the indicator selector
knob (2) for more than 3 seconds.
• To select the setting that you want to
change, turn the indicator selector knob
(2) left or right.
• To change the setting, push the indicator
selector knob (2).
• To exit the setting mode, select “Back”
and push the indicator selector knob (2).
68PH02231
NOTE:
The currently selected setting item is sur-
rounded by a frame.
NOTE:
• If you push and hold the indicator selec-
tor knob (2) to enter the setting mode
when the display (C) shows average fuel
consumption or average speed, the
value will be reset simultaneously. If you
do not want to reset the value, push the
indicator selector knob quickly to switch
the indication of the display.
• If you turn the ignition switch, press the
engine switch or start to move the vehi-
cle when the display is in the setting
mode, the setting mode will be canceled
automatically.
Distance unit
(Odometer / trip meter distance unit set-
ting)
You can change the units in which odome-
ter / trip meter distance is displayed.
NOTE:
When you change the units in which odom-
eter / trip meter distance is displayed, the
trip meter will be reset automatically.
Fuel economy
(Fuel consumption unit setting)
You can change the units that fuel con-
sumption is displayed in.
Language
You can change the language of the infor-
mation display.
Fuel reset (Average fuel consumption
reset setting)
You can change when the value of aver-
age fuel consumption is reset.
Temperature
(Temperature unit setting)
You can change the units that temperature
is displayed in.
NOTE:
When you change the units that tempera-
ture is displayed in, the automatic heating
and air conditioning system (if equipped)
temperature display units will be changed
automatically.
Set sensors
(Parking sensor setting) (if equipped)
The parking sensor can be switched
between the normal mode and trailer
mode.
EXAMPLE
2-83
BEFORE DRIVING
Clock setting
(Adjusting the clock)
• To change the hour indication, turn the
indicator selector knob (2) left or right
repeatedly when the hour indication
appears as reversed color. To change
the hour indication quickly, turn and hold
the indicator selector knob (2). To set the
hour indication, push the indicator selec-
tor knob (2) and the minute indication
appears as reversed color.
• To change the minute indication, turn the
indicator selector knob (2) left or right
repeatedly when the minute indication
appears as reversed color. To change
the minute indication quickly, turn and
hold the indicator selector knob (2). To
set the minute indication, push the indi-
cator selector knob (2).
You can also switch the time indication
between 12-hour and 24-hour format.
(Adjusting the date)
Adjust year, month, and day by operating
the indicator selector knob (2) in the same
way as the adjusting the clock.
Door lock (Door lock setting)
You can choose either once or twice oper-
ation(s) to unlock all doors (including the
tailgate) by turning the key, or operating
keyless push start system remote control-
ler or request switch.
You can also turn off or on the buzzer
sound when the door(s) is(are) locked or
unlocked.
Lights
(Light setting)
(Footwell light setting) (if equipped)
The footwell lights can be programmed for
interlocked operation with either lighting
control or door operation and for no light-
ing.
(Lane Change setting)
The turn signal and its indicator can be set
whether they flash three times even if you
return the turn signal control lever immedi-
ately after moving it.
Guide me light setting (Light Setting)
(if equipped)
You can change the lighting time of “To
car” function or “To home” function.
Antitheft (Theft deterrent alarm system
setting) (if equipped)
You can switch the theft deterrent alarm
system from the enabled state to the dis-
abled state, and vice versa.
The state of the theft deterrent alarm sys-
tem is shown on the information display as
follows:
• Mode A: Disabled state
• Mode D: Enabled state
(Shock sensor system setting)
You can change the on/off of the shock
sensor.
(Shock sensor P setting)
You can adjust the pre-warning sensitivity
of shock sensor.
(Shock sensor F setting)
You can adjust the full blast warning sensi-
tivity of shock sensor.
Display item (car color setting)
You can change the car color of the infor-
mation display.
(Calendar dis setting)
You can change the on/off of the calendar.
(Calendar form setting)
You can change the calendar form of the
information display.
Fuel eco history
(Fuel Economy History Setting)
Transitional indication of average fuel
consumption can be switched to timed
indication and driving cycle indication.
2-84
BEFORE DRIVING
Default (initialization setting)
If you select “YES” and push the indicator
selector knob (2), all settings will be reini-
tialized.
Trip Summary display
Trip Summary display comes when ignition
mode is switched to ‘OFF” position. Fol-
lowing summary is displayed.
• Driving Time : Time from ignition “ON”
condition to ignition “OFF” condition is
displayed.
• Driving Mileage : Distance covered from
ignition “OFF” condition is displayed.
Warning and Indicator Messages
The display shows warning and indicator
messages to let you know about certain
vehicle problems.
A tone may also sound to alert you.
If warning and indicator messages appear
on the display, follow the messages.
Master warning indicator light
78K049
When the display shows warning and indi-
cator messages, the master warning indi-
cator light may also blink.
NOTE:
• When the problem that causes a mes-
sage to appear is corrected, the mes-
sage will disappear.
• If a message is displayed, and other
problems requiring a message occur, the
message for each of the problems will
be alternately displayed about every 5
seconds.
• When you push and hold the indicator
selector knob (2) for about 2 seconds
while a message is displayed, the mes-
sage will disappear temporarily. If the
problem that caused the message is not
corrected, the message will appear
again after 5 seconds.
2-85
BEFORE DRIVING
Warning and indicator messages
All model
(#1) This message will disappear for a while even if the problem that caused the message to appear is not corrected.
Warning and indicator
message
Master warning
indicator light
Sound Cause and remedy
68PH02232
Blinks
(only while vehicle
is in motion)
Beep (one time from interior
buzzer; only while vehicle is
in motion)
A door or tailgate is not properly closed.
Stop the vehicle in a safe place and close
the door or tailgate properly. (#1)
68PH02233
Blinks Continuous beep (from inte-
rior buzzer)
The headlights and/or the position lights are
left on. Turn them off.
2-86
BEFORE DRIVING
(#1) This message will disappear for a while even if the problem that caused the message to appear is not corrected.
Warning and indicator
message
Master warning
indicator light
Sound Cause and remedy
68PH02234
Off Beep (one time from interior
buzzer)
Fuel is low. Refill it immediately. (#1)
68PH02235
Off Off The road may be icy. Drive very carefully.
(#1)
2-87
BEFORE DRIVING
(#1) This message will disappear for a while even if the problem that caused the message to appear is not corrected.
Warning and indicator
message
Master warning
indicator light
Sound Cause and remedy
68PH02237
Off Off This message is displayed when “ACC”
position is selected as the power supply
position. (#1)
68PH02238
Off Off The clutch pedal is depressed. Press the
engine switch to start the engine.
2-88
BEFORE DRIVING
Warning and indicator
message
Master warning
indicator light
Sound Cause and remedy
68PH02236
Blinks Beep (one time from interior
buzzer)
If this message is displayed, have your
vehicle inspected by an authorized Maruti
Suzuki workshop.
2-89
BEFORE DRIVING
Warning and indicator
message
Master warning
indicator light
Sound Cause and remedy
68PH02239
Blinks Beep (one time from interior
buzzer)
There is a problem with the steering lock
system.
Have your vehicle inspected by an autho-
rized Maruti Suzuki workshop.
68PH02240
Blinks Beep (one time from interior
buzzer)
There is a problem with the keyless push
start system.
Have your vehicle inspected by an autho-
rized Maruti Suzuki workshop.
2-90
BEFORE DRIVING
Warning and indicator
message
Master warning
indicator light
Sound Cause and remedy
68PH02241
Blinks Series of beeps under cer-
tain conditions (for about 2
seconds from exterior and/or
interior buzzers)
The remote controller may be outside the
vehicle or its battery may have become dis-
charged. Locate the remote controller or
touch the engine switch with the remote
controller.
If the message still appears, replace the
remote controller battery.
68PH02242
2-91
BEFORE DRIVING
(#1) This message will disappear for a while even if the problem that caused the message to appear is not corrected.
Warning and indicator
message
Master warning
indicator light
Sound Cause and remedy
68PH02243
Off Off This message is displayed when “ON” posi-
tion is selected as the power supply posi-
tion. (#1)
68PH02244
Blinks Beep (one time from interior
buzzer)
The steering lock is not disengaged. While
lightly turning the steering wheel in both
directions, press the engine switch again.
2-92
BEFORE DRIVING
(#1) This message will disappear for a while even if the problem that caused the message to appear is not corrected.
Warning and indicator
message
Master warning
indicator light
Sound Cause and remedy
68PH02245
Off Off The remote controller battery is about to
become flat. Replace the battery. (#1)
68PH02246
Off Off The engine switch is pressed without
depressing the brake and clutch pedals. Try
again as instructed by the message.
2-93
BEFORE DRIVING
Diesel engine model
Warning and indicator
message
Master warning
indicator light
Sound Cause and remedy
68PH02247
Blinks Beep (one time from interior
buzzer)
There may be a problem with the fuel filter.
Have your vehicle inspected by an autho-
rized Maruti Suzuki workshop.
68PH02248
Blinks Beep (one time from interior
buzzer)
It is possible that water may be in the fuel
filter.
Have your vehicle inspected by an autho-
rized Maruti Suzuki workshop.
2-94
BEFORE DRIVING
• If your vehicle is equipped with a parking sensor system, the information display also indicates warning and indicator messages
related to the system. For information on these messages, refer to “Parking sensors (if equipped)” in “OPERATING YOUR VEHICLE”
section.
Warning and indicator
message
Master warning
indicator light
Sound Cause and remedy
68PH02249
Off Off If the coolant temperature is cool enough,
this message is displayed when the engine
switch is pressed to change the ignition
mode to “ON” and this message will disap-
pear when the glow plug is heated enough
for engine starting.

Related Topics

Before Driving
Keys Door Locks Keyless Push Start System Remote Controller / Keyless Entry System Transmitter Security System (if equipped) Theft Deterrent Light (if equipped) Windows Mirrors Front Seats Rear Seats Seat Belts and Child Restraint Systems Child Restraint System for India Seat Belt Pretensioner System Supplemental Restraint System (air bags) Instrument Cluster (Type A) (if equipped) Speedometer (Type A) Fuel Gauge (Type A) Brightness Control (Type A) Information Display (Type A) Instrument Cluster (Type B) (if equipped) Speedometer (Type B) Tachometer (Type B) Fuel Gauge (Type B) Temperature Gauge (Type B) Brightness Control (Type B) Information Display (Type B) Speedometer (Type C) Tachometer (Type C) Fuel Gauge (Type C) Temperature Gauge (Type C) Brightness Control (Type C) Information Display (Type C) Warning and Indicator Lights Lighting Control Lever Headlight Leveling Switch Turn Signal Control Lever Hazard Warning Switch Windshield Wiper and Washer Lever Tilt/Telescoping Steering Lock Lever Horn Heated Rear Window Switch (if equipped)

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot