Get BEFORE DRIVING -> Keyless Push Start System Remote Controller/Keyless Entry System Transmitter Guide for Suzuki Swift 4 Door Second Generation (2010-2015)

Door Locks: 3, 5, 8

BEFORE DRIVING

Keyless Push Start System

Remote Controller/Keyless

Entry System Transmitter

WARNING

Always make sure that the tailgate is

closed and latched securely. Com-

pletely closing the tailgate helps pre-

vent occupants from being thrown

from the vehicle in the event of an

accident. Completely closing it also

helps keep exhaust gases from enter-

ing the vehicle.

Type A

Type B

(2)

If you cannot unlatch the tailgate by push-

ing the unlatch switch (1) due to a dis-

charged battery or malfunction, follow the

procedures below to unlatch the tailgate

from inside the vehicle.

68LM246

2) Push open the tailgate from inside by

pushing up on the emergency lever (2)

using a flat blade screwdriver or the

jack handle. The tailgate will be latched

again by closing the tailgate simply.

1) Fold the rear seat forward for easier

access. Refer to “Folding Rear Seats”

section for details on how to fold the

rear seat forward.

68LM205

Your vehicle is equipped with either a key-

less push start system remote controller

(Type A) or a keyless entry system trans-

mitter (Type B). The remote controller has

a keyless entry system and a keyless push

start system. The transmitter has only a

keyless entry system. For details, refer to

the following explanations.

If the tailgate cannot be unlatched by push-

ing the unlatch switch (1), have the vehicle

inspected by your SUZUKI dealer.

CAUTION

• To avoid injury, do not use your fin-

ger to push the emergency lever.

• Make sure there is no one near the

tailgate when pushing open the tail-

gate from inside the vehicle.

2-5

58MS0-14E

Door Locks: 3, 5, 8

BEFORE DRIVING

Keyless Push Start System Remote

When the doors are unlocked:

Controller (Type A)

• The turn signal lights will flash twice and

the exterior buzzer will sound twice.

• If the interior light switch is in the

“DOOR” position, the interior light will

turn on for about 15 seconds and then

fade out. If you press the engine switch

during this time, the light will start to fade

out immediately.

The remote controller enables the following

operations:

• You can lock or unlock the doors by

operating the LOCK/UNLOCK buttons

on the remote controller. Refer to the

explanation in this section.

• You can lock or unlock the doors by

pushing the request switch on the door

handle. For details, refer to the explana-

tion in this section.

• You can start the engine without using

an ignition key. For details, refer to

“Engine Switch” in the “OPERATING

YOUR VEHICLE” section.

(2)

(1)

Be sure the doors are locked after you

operate the “LOCK” button (1).

If no door is opened within about 30 sec-

onds after the “UNLOCK” button (2) is

operated, the doors will automatically lock

again.

68LM206

(1) “LOCK” button

(2) “UNLOCK” button

NOTE:

• The maximum operating distance of the

remote controller is about 5 m (16 ft.),

but this can vary depending on the sur-

roundings, especially near other trans-

mitting devices such as radio towers or

CB (Citizen’s Band) radios.

• The door locks cannot be operated with

the remote controller if the ignition mode

is other than the “LOCK” (OFF).

• When any door is open, if you push the

“LOCK” button on the remote controller,

the exterior buzzer will sound and doors

cannot be locked.

You can lock or unlock all doors (including

the tailgate) simultaneously by operating

the remote controller near the vehicle.

Central door locking system

• To lock all doors, push the “LOCK” but-

ton (1) once.

• To unlock only the driver’s door, push the

“UNLOCK” button (2) once.

• To unlock other doors, push the

“UNLOCK” button (2) once again.

The turn signal lights will flash once and

the exterior buzzer will sound once when

the doors are locked.

2-6

58MS0-14E

Door Locks: 3, 5, 8

BEFORE DRIVING

• If you lose one of the remote controllers,

ask your SUZUKI dealer as soon as pos-

sible for a replacement. Be sure to have

your dealer program the new remote

controller code in your vehicle’s memory

so that the old code is erased.

The turn signal lights will flash once and

the exterior buzzer will sound once when

the doors are locked.

EXAMPLE

(1)

When the doors are unlocked:

• The turn signal lights will flash twice and

the exterior buzzer will sound twice.

• If the interior light switch is in the

“DOOR” position, the interior light will

turn on for about 15 seconds and then

fade out. If you press the engine switch

during this time, the light will start to fade

out immediately.

(1)

Keyless unlocking/locking using the

request switches

(1)

Be sure the doors are locked after you

operate the request switch to lock the

doors.

80J056

(1) 80 cm (2 1/2 feet)

When the remote controller is within

approximately 80 cm (2 1/2 feet) from a

front door handle or the tailgate switch, you

can lock or unlock the doors by pushing

the request switch.

NOTE:

• The door locks cannot be operated by

the request switch under the following

conditions:

(1)

EXAMPLE

– If any door is open or is not completely

closed.

– If the ignition mode is other than

“LOCK” (OFF).

• If no doors are opened within about 30

seconds after unlocking the doors by

pushing the request switch, the doors

will be locked again automatically.

58MST0202

NOTE:

When the remote controller is within the

operating range described in this section,

you can lock or unlock the doors (including

the tailgate) by pushing the request switch

(1) on the door handle of the driver’s door,

front passenger’s door or tailgate.

• If the remote controller is outside the

request

switch

operating

range

described above, you will not be able to

operate the request switch.

• If the battery of the remote controller

runs down or there are strong radio

waves or noise, the request switch oper-

ating range may be reduced or the

remote controller may be inoperative.

• If the remote controller is too close to the

door glass, the request switches may not

operate.

To unlock a door or all doors:

• Push the request switch on the door

handle once to unlock only one door.

• Push the request switch on the door

handle twice to unlock all doors.

2-7

58MS0-14E

Door Locks: 3, 5, 8

Windows: 3, 8

BEFORE DRIVING

• If a spare remote controller is in the vehi-

cle, the request switches may not oper-

ate normally.

• When the remote controller is in contact

with or covered by a metal object.

• When a radio wave type remote keyless

entry is used nearby.

• When the remote controller is placed

near an electronic device such as per-

sonal computer.

Some additional precautions you should

take and information you should be aware

of are:

• Make sure the key is stowed in the

remote controller. If the remote controller

becomes unreliable, you will not be able

to lock or unlock the doors.

• The remote controller will only operate a

request switch if it is within the switch’s

operating range. For example, if the

remote controller is within the operating

range of the driver’s door request switch

but not the front passenger’s door

request switch or the tailgate request

switch, the driver’s door switch can be

operated but the front passenger’s door

switch or tailgate switch cannot be oper-

ated.

57L21016

• Be sure that the driver always carries the

remote controller.

To stow the key into the remote controller,

push the key in the remote controller until

you hear a click.

NOTICE

• If you lose one of the remote controllers,

ask your SUZUKI dealer as soon as pos-

sible for a replacement. Be sure to have

your dealer program the new remote

controller code in your vehicle’s memory

so that the old code is erased.

• You can use up to four remote controllers

and the keys for your vehicle. Ask your

SUZUKI dealer for details.

The remote controller is a sensitive

electronic instrument. To avoid dam-

aging the remote controller:

• Do not expose it to impacts, mois-

ture or high temperature such as by

leaving it on the dashboard under

direct sunlight.

• Keep the remote controller away

from magnetic objects such as a

television.

(A)

• The battery life of the remote controller

is about two years, but it can vary

depending on usage conditions.

NOTE:

The keyless push start system may not

function correctly in certain environments

or under certain operating conditions such

as the following:

• When there are strong signals coming

from a television, power station or a cel-

lular phone.

68LM247

To remove the key from the remote control-

ler, push the button (A) in the direction of

the arrow and pull the key out from the

remote controller.

2-8

58MS0-14E

Windows: 3, 8

BEFORE DRIVING

Request Switch Warning Buzzer

This exterior buzzer beeps for about 2 sec-

onds in the following conditions to warn

you that the request switch is not working:

• The request switch is pressed after all

doors are closed with the ignition mode

changed to “ACC” or “ON” by pressing

the engine switch.

• The request switch is pressed in any of

the following conditions after changing

the ignition mode to “LOCK” (OFF) by

pressing the engine switch.

Reminder function

• If you open the driver’s door and lock the

door by turning the lock knob forward or

pushing the power door locking switch,

the driver’s door will be automatically

unlocked.

• If you open the front passenger’s door

and lock the door by turning the lock

knob forward or pushing the power door

locking switch, the front passenger’s

door will be automatically unlocked.

NOTE:

– The remote controller is left inside the

vehicle.

• The reminder will not operate when the

remote controller is on the instrument

panel, in the glove box, in a storage

compartment, in the sun visor or on the

floor etc.

• Be sure that the driver always carries the

remote controller.

EXAMPLE

– Any of the doors is open.

58MST0203

If the remote controller is not in the vehicle

under the following conditions, the buzzer

sounds intermittently for about 2 seconds

and the immobilizer/keyless push start sys-

tem warning light on the instrument cluster

blinks:

• When one or more doors are opened

and all of the doors are later closed with

the ignition mode is other than “LOCK”.

Press the request switch again after doing

the following:

With the ignition mode changed to “LOCK”

(OFF) by pressing the engine switch, bring

out the remote controller if it is inside the

vehicle and check that all doors are com-

pletely closed.

• Do not leave the remote controller in the

vehicle when leaving the vehicle.

The indicator light will turn off within sev-

eral seconds after the remote controller is

returned to an area of the vehicle other

than the rear luggage area.

If the remote controller is left in the vehicle

and you lock the driver’s door or front pas-

senger’s door as described below, the door

will be automatically unlocked.

2-9

58MS0-14E

Windows: 3, 8

BEFORE DRIVING

WARNING

Replacement of the battery

If the remote controller becomes unreli-

able, replace the battery.

Swallowing a lithium battery may

cause serious internal injury. Do not

allow anyone to swallow a lithium

battery. Keep lithium batteries away

from children and pets. If swallowed,

contact a physician immediately.

To replace the battery of the remote con-

troller:

(1)

NOTICE

The remote controller is a sensitive

electronic instrument. To avoid dam-

aging it, do not expose it to dust or

moisture or tamper with internal parts.

68LM210

(1) Lithium disc type battery:

CR2032 or equivalent

NOTE:

Used batteries must be disposed properly

according to applicable rules or regulations

and must not be disposed with ordinary

household trash.

3) Replace the battery (1) so its + terminal

faces the bottom of the case as shown

in the illustration.

4) Close the remote controller firmly.

5) Make sure the door locks can be oper-

ated with the remote controller.

6) Dispose of the used battery properly

according to applicable rules or regula-

tions. Do not dispose of lithium batter-

ies with ordinary household trash.

71LMT0201

1) Pull the key out from the remote con-

troller.

2) Insert a flat blade screwdriver covered

with a soft cloth in the slot of the remote

controller and pry it open.

2-10

58MS0-14E

Mirrors: 3, 8

BEFORE DRIVING

Keyless Entry System Transmitter

(Type B)

Central door locking system

• To lock all doors, push the “LOCK” but-

ton (1) once.

• To unlock only the driver’s door, push the

“UNLOCK” button (2) once.

• To unlock other doors, push the

“UNLOCK” button (2) once again.

NOTE:

• The maximum operating distance of the

keyless entry system transmitter is about

5 m (16 ft.), but this can vary depending

on the surroundings, especially near

other transmitting devices such as radio

towers or CB (Citizen’s Band) radios.

• The door locks cannot be operated with

the transmitter, if the ignition key is

inserted in the ignition switch.

When the doors are unlocked:

• The turn signal lights will flash twice.

• If the interior light switch is in the

“DOOR” position, the interior light will

turn on for about 15 seconds and then

fade out. If you insert the key into the

ignition switch during this time, the light

will start to fade out immediately.

• When any door is open, the door locks

can be operated only unlock with the

transmitter, and the turn signal light will

not flash.

• If you lose one of the transmitters, ask

your SUZUKI dealer as soon as possible

for a replacement. Be sure to have your

dealer program the new transmitter code

in your vehicle’s memory so that the old

code is erased.

(1)

(2)

81A184

Be sure the doors are locked after you

operate the “LOCK” button (1).

(1) “LOCK” button

(2) “UNLOCK” button

NOTE:

You can lock or unlock all doors (including

the tailgate) simultaneously by operating

the transmitter near the vehicle.

If no door is opened within about 30 sec-

onds after the “UNLOCK” button (2) is

operated, the doors will automatically lock

again.

NOTICE

The transmitter is a sensitive elec-

tronic instrument. To avoid damaging

the transmitter:

• Do not expose it to impacts, mois-

ture or high temperature such as by

leaving it on the dashboard under

direct sunlight.

• Keep the transmitter away from

magnetic objects such as a televi-

sion.

2-11

58MS0-14E

Mirrors: 3, 8

Seat Adjustment: 3

BEFORE DRIVING

WARNING

Replacement of the Battery

If the transmitter becomes unreliable,

replace the battery.

(2)

Swallowing a lithium battery may

cause serious internal injury. Do not

allow anyone to swallow a lithium

battery. Keep lithium batteries away

from children and pets. If swallowed,

contact a physician immediately.

To replace the battery of the transmitter:

(1)

(3)

NOTICE

(2)

The transmitter is a sensitive elec-

tronic instrument. To avoid damaging

it, do not expose it to dust or mois-

ture or tamper with internal parts.

68LM249

(3) Lithium disc type battery:

CR1616 or equivalent

NOTE:

Used batteries must be disposed properly

according to applicable rules or regulations

and must not be disposed with ordinary

household trash.

3) Put the edge of a flat blade screwdriver

in the slot of the transmitter (2) and pry

it open.

4) Replace the battery (3) so its + terminal

faces the “+” mark of the transmitter.

5) Close the transmitter and install it into

the transmitter holder.

68LM248

1) Remove the screw (1), and open the

transmitter cover.

2) Remove the transmitter (2).

6) Close the transmitter cover, install and

tighten the screw (1).

7) Make sure the door locks can be oper-

ated with the transmitter.

8) Dispose of the used battery properly

according to applicable rules or regula-

tions. Do not dispose of lithium batter-

ies with ordinary household trash.

2-12

58MS0-14E

BEFORE DRIVING -> Keyless Push Start System Remote Controller/Keyless Entry System Transmitter for Your Suzuki Swift 4 Door Second Generation (2010-2015)

Related Topics

Popular Owner Manuals

Latest Owner Manuals