Instruments and controls for Your Vauxhall Vivaro Van Third Generation (2019-2026)

Instruments and controls  
93  
Engine coolant temperature  
Engine oil pressure .................. 115  
Low fuel ................................... 116  
Charging cable connected ....... 116  
Vehicle ready ........................... 116  
Reduced engine power ........... 116  
Autostop .................................. 116  
Exterior light ............................ 116  
Low beam ................................ 116  
High beam ............................... 116  
High beam assist ..................... 116  
LED headlights ........................ 117  
Front fog lights ......................... 117  
Rear fog light ........................... 117  
Rain sensor ............................. 117  
Cruise control .......................... 117  
Semi-adaptive cruise control ... 117  
Pedestrian safety alert fault ..... 117  
Side blind spot alert ................. 117  
Active emergency braking ....... 117  
Speed limiter ........................... 117  
Door open ................................ 117  
Instruments and  
controls  
gauge ..................................... 108  
Engine oil level monitor ........... 109  
Service display ........................ 109  
Control indicators .................... 110  
Turn lights ................................ 111  
Seat belt reminder ................... 111  
Airbag and belt tensioners ....... 111  
Airbag deactivation .................. 112  
Charging system ..................... 112  
Malfunction indicator light ........ 112  
Service vehicle soon ............... 112  
Stop engine ............................. 112  
System check .......................... 113  
Brake system ........................... 113  
Parking brake .......................... 113  
Electric parking brake .............. 113  
Electric parking brake fault ...... 113  
Automatic operation of electric  
Controls ....................................... 94  
Steering wheel adjustment ........ 94  
Steering wheel controls ............. 94  
Horn ........................................... 95  
Pedestrian safety alert ............... 95  
Steering column controls ........... 95  
Windscreen wiper and washer . . 96  
Rear window wiper and  
washer ...................................... 97  
Outside temperature .................. 98  
Clock ......................................... 98  
Power outlets ............................. 98  
Warning lights, gauges and indi‐  
parking brake off .................... 113  
Antilock brake system (ABS) ... 114  
Gear shifting ............................ 114  
Lane departure warning .......... 114  
Electronic Stability Control and  
Traction Control system ......... 114  
Engine coolant temperature .... 114  
Preheating ............................... 115  
Exhaust filter ............................ 115  
AdBlue ..................................... 115  
Deflation detection system ...... 115  
cators ......................................... 100  
Instrument cluster .................... 100  
Speedometer ........................... 105  
Odometer ................................ 105  
Trip odometer .......................... 105  
Tachometer ............................. 106  
Fuel gauge .............................. 106  
High voltage battery gauge ..... 107  
Power indicator gauge ............. 108  
Comfort consumption gauge ... 108  
Displays ..................................... 118  
Driver Information Centre ........ 118  
Info Display .............................. 123  
Head-up display ...................... 125  
Vehicle messages ...................... 126  
Warning chimes ....................... 127  
Vehicle personalisation .............. 127  
94  
Instruments and controls  
Telematics services ................... 132  
Vauxhall Connect .................... 132  
ERA GLONASS ....................... 132  
Steering wheel controls  
Controls  
Steering wheel adjustment  
The menus and functions of the  
Driver Information Centre can be  
selected via the rotary knob on the left  
steering wheel stalk.  
Driver Information Centre 3 118.  
Infotainment system can be operated  
via the steering wheel controls.  
Unlock lever, adjust steering wheel,  
then engage lever and ensure it is  
fully locked.  
Do not adjust steering wheel unless  
vehicle is stationary and steering  
wheel lock has been released.  
Further information is available in the  
Infotainment Manual.  
Instruments and controls  
Steering column controls  
95  
Steering wheel paddles  
Horn  
On vehicles with automatic  
transmission, gearshifting can be  
operated via + or -.  
Automatic transmission 3 172.  
Manual mode 3 173.  
Press d.  
Cruise control, semi-adaptive cruise  
control and speed limiter are  
operated via the driver assistance  
control on the left side of the steering  
column.  
Cruise control 3 184.  
Speed limiter 3 187.  
Pedestrian safety alert  
The sound of the pedestrian safety  
alert is generated to indicate the  
vehicle presence to pedestrians. It is  
active up to 19 mph.  
Semi-adaptive cruise control 3 191.  
96  
Instruments and controls  
To activate interval wiping mode the  
next time ignition is switched on,  
press the lever downwards to position  
0 and back to INT.  
windscreen wiper. To deactivate the  
automatic wiping mode, press the  
lever downwards to AUTO again.  
Windscreen wiper and  
washer  
Windscreen wiper with adjustable  
wiper interval  
If ignition is switched off for more than  
a minute, automatic wiping mode is  
deactivated. To activate automatic  
wiping mode the next time ignition is  
switched on, press the lever  
Windscreen wiper with rain sensor  
downwards to AUTO again.  
For a single wipe when the  
windscreen wiper is off, pull the lever  
briefly towards you.  
Do not use if the windscreen is frozen.  
Switch off in car washes.  
Windscreen washer  
2
1
: fast  
2
: fast  
: slow  
1
: slow  
INT : interval wiping  
INT  
0
: interval wiping  
: off  
0
: off  
AUTO : automatic wiping with rain  
sensor  
For a single wipe when the  
windscreen wiper is off, press the  
lever down.  
Do not use if the windscreen is frozen.  
Switch off in car washes.  
In AUTO position, the rain sensor  
detects the amount of water on the  
windscreen and automatically  
regulates the frequency of the  
Instruments and controls  
97  
Washer fluid is sprayed onto the  
windscreen and the wiper wipes a few  
times.  
Activation or deactivation of this  
function can be changed in the  
Vehicle personalisation menu 3 127.  
Rear window wiper and  
washer  
Washer fluid 3 239.  
Rear window wiper  
Rear window washer  
Functionality of the rain sensor  
0
: off  
Set to R.  
S
R
: intermittent operation  
: rear window washer  
Keep the sensor free from dust, dirt  
and ice.  
Control indicator y 3 96.  
Washer fluid is sprayed onto the rear  
window and the wiper wipes a few  
times.  
The rear window washer system is  
deactivated when the fluid level is  
low.  
Do not use if the rear window is  
frozen.  
Switch off in car washes.  
The rear window wiper comes on  
automatically when the windscreen  
wiper is switched on and reverse gear  
is engaged.  
Washer fluid 3 239.  
98  
Instruments and controls  
Outside temperature  
Clock  
Power outlets  
Illustration shows an example.  
Illustration shows an example.  
Date and time are shown in the Info  
Display.  
The adjustment of date and time is  
described in the Infotainment Manual.  
Info Display 3 123.  
A 12 V power outlet is located in the  
glovebox.  
If outside temperature drops to 3 °C,  
a warning message is displayed in the  
Driver Information Centre.  
9 Warning  
The road surface may already be  
icy even though the display  
indicates a few degrees above 0  
°C.  
Instruments and controls  
99  
A 12 V power outlet is located in the  
centre console.  
A 12 V power outlet may be located  
on the third row left side trim.  
A 220 V power outlet may be located  
underneath the front passenger seat.  
Do not exceed the maximum power  
A 12 V power outlet may be located  
at the lower left side of the B-pillar.  
Another 12 V power outlet may be  
located at the lower left side of the D-  
pillar.  
Do not exceed the maximum power  
consumption of 120 W.  
consumption of 120 W.  
With ignition off, the power outlets are  
deactivated. Additionally the power  
outlets are deactivated in the event of  
low vehicle battery voltage.  
Electrical accessories that are  
connected must comply with the  
electromagnetic compatibility  
requirements laid down in  
DIN VDE 40 839.  
Do not connect any current-delivering  
accessories, e.g. electrical charging  
devices or batteries.  
100  
Instruments and controls  
Do not damage the outlet by using  
unsuitable plugs.  
Stop-start system 3 161.  
Infotainment system. For further  
information, see Infotainment  
Manual.  
Warning lights, gauges  
and indicators  
Notice  
Instrument cluster  
USB port  
The sockets must always be kept  
clean and dry.  
Depending on the version, three  
instrument clusters are available:  
●
●
●
Baselevel  
Midlevel  
Uplevel  
A USB port is located in the  
instrument panel.  
A USB port may be located within the  
compartment located above the  
glovebox.  
A further USB port may be located in  
the rear console.  
The USB ports are prepared for  
charging external devices and  
provide a data connection to the  
Instruments and controls  
101  
Baselevel instrument cluster  
102  
Instruments and controls  
Midlevel instrument cluster  
Instruments and controls  
103  
Uplevel instrument cluster  
104  
Instruments and controls  
Cluster electric vehicle  
X
h
i
1
D
A
B
G
System check 3 113  
Parking brake 3 113  
Exterior light 3 116  
Low beam 3 116  
Antilock brake system  
(ABS) 3 114  
High beam 3 116  
High beam assist 3 116  
Front fog lights 3 117  
Rear fog light 3 117  
Rain sensor 3 117  
Y Z Gear shifting 3 114  
Q
Lane departure warning  
3 114  
H
y
J
Electronic Stability Control  
Overview  
and Traction Control  
,
Side blind spot alert 3 117  
Cruise control 3 117  
1
Turn lights 3 111  
system 3 114  
v
a
Seat belt reminder 3 111  
z
Preheating 3 115  
Q
Semi-adaptive cruise  
control 3 117  
d
Airbag and belt tensioners  
3 111  
+
Exhaust filter 3 115  
B
AdBlue 3 115  
5
Speed limiter 3 117  
e
Airbag deactivation 3 112  
Charging system 3 112  
q
Tyre deflation detection  
system 3 115  
m
Active emergency braking  
3 117  
S
W
Malfunction indicator light  
3 112  
T
Engine oil pressure 3 115  
O
Door open 3 117  
r 2  
Low fuel 3 116  
i
Service vehicle soon  
3 112  
C
Service vehicle soon  
3 112  
V 2 Engine coolant tempera‐  
ture high 3 114  
j
Charge cord connected  
3 116  
LED headlights 3 117  
ñ
Autostop 3 116  
STOP Stop engine 3 112  
Instruments and controls  
Baselevel instrument cluster  
105  
Odometer  
READY Vehicle ready 3 116  
M
Reduced engine power  
3 116  
K
Pedestrian safety alert  
fault3 117  
N
Battery gauge 3 107  
Speedometer  
Trip odometer counts up to  
9,999.9 miles without automatic  
reset.  
The total recorded distance is  
displayed in miles.  
Press F for 2 seconds to reset  
trip odometer.  
Trip odometer  
The recorded distance since the last  
reset is displayed in the Driver  
Information Centre.  
Indicates vehicle speed.  
106  
Instruments and controls  
Midlevel instrument cluster  
Uplevel instrument cluster  
Tachometer  
Trip odometer counts up to  
9,999.9 miles without automatic  
reset.  
Press SET 000 for 2 seconds to reset  
trip odometer.  
Trip odometer counts up to  
1,999.9 miles and resets then  
automatically.  
Press 000 for 2 seconds to reset trip  
odometer.  
Displays the engine speed.  
Drive in a low engine speed range for  
each gear as much as possible.  
Caution  
Driver Information Centre 3 118.  
If the needle is in the red warning  
zone, the maximum permitted  
engine speed is exceeded. Engine  
at risk.  
Fuel gauge  
Displays the fuel level in the tank.  
Never run the fuel tank dry.  
Instruments and controls  
107  
The arrow indicates the vehicle side  
where the fuel filler flap is located.  
Midlevel and uplevel instrument  
cluster  
High voltage battery gauge  
Because of the fuel remaining in the  
tank, the top-up quantity may be less  
than the specified tank capacity.  
Baselevel cluster  
The high voltage battery gauge  
displays the charging level of the high  
voltage battery.  
If the control indicator 2 illuminates  
yellow, refuel the tank immediately.  
A scale consisting of white segments  
shows the fuel level.  
If the control indicator r illuminates  
yellow, refuel the tank immediately.  
108  
Instruments and controls  
If the drive mode Eco mode is  
selected, the performance of the  
thermal consumers is reduced. The  
needle of the comfort consumption  
gauge is in the ECO zone.  
Power indicator gauge  
Comfort consumption  
gauge  
Engine coolant temperature  
gauge  
Displays the coolant temperature.  
Caution  
If engine coolant temperature is  
too high, stop vehicle, switch off  
engine. Danger to engine. Check  
coolant level.  
The power indicator gauge informs  
about the current energy situation of  
the vehicle.  
Charge : High voltage battery is  
being charged with energy  
resulting from braking or  
The comfort consumption gauge  
informs about the current electric  
consumption caused by the following  
thermal consumers:  
●
●
●
●
●
heating  
deceleration of the vehicle  
air conditioning  
heated windscreen  
heated rear window  
heated seats  
Eco  
: An optimum in energy is  
accessible in all driving  
modes  
Power : Vehicle is driven in a  
dynamic driving style with  
focus on performance  
Instruments and controls  
Engine oil level monitor  
109  
Baselevel cluster  
Midlevel and uplevel instrument  
cluster  
The state of the engine oil level is  
displayed in the Driver Information  
Centre for a few seconds following  
the service information after switching  
on the ignition.  
A proper state of engine oil level is  
confirmed.  
If engine oil level is low, T flashes  
and warning message is indicated in  
the Driver Information Centre.  
Depending on the version, D  
flashes in the Driver Information  
Centre. Confirm engine oil level by  
using the oil dipstick and top up  
engine oil respectively.  
A scale consisting of white segments  
shows the engine coolant  
temperature.  
If the engine coolant temperature is  
too high, the control indicator V  
illuminates red.  
70 °C  
90 °C  
: engine operating  
temperature not yet  
reached  
Engine oil 3 237.  
: normal operating  
temperature  
A fault of measurement is indicated  
by E or a message in the Driver  
Information Centre together with  
T. Check engine oil level manually  
by using the dipstick.  
red zone : temperature too high  
Switch off engine immediately.  
Control indicator 2 illuminates if  
coolant temperature is too high.  
Switch off engine immediately.  
Service display  
The service system informs when to  
change the engine oil and filter or a  
vehicle service is required. Based on  
110  
Instruments and controls  
driving conditions, the interval at  
which an engine oil and filter change  
is required can vary considerably.  
the distance travelled since the due  
date is indicated in the Driver  
Information Centre.  
A disappears  
Retrieving service information  
Service information 3 281.  
Overdued service is indicated by a  
message in the Driver Information  
Centre which indicates the overdued  
distance. A flashes and then  
illuminates permanently until service  
is executed. Additionally, the control  
indicator C or SERVICE  
To retrieve the status of the service  
information at any time press F,  
G or CHECK.  
The service information is displayed  
for a few seconds.  
Instrument cluster 3 100.  
Service information 3 281.  
A required service due is displayed in  
the Driver Information Centre for  
several seconds after switching on  
the ignition.  
If no service is required for the next  
1800 miles or more no service  
illuminates.  
information appears in the display.  
If service is required within the next  
1800 miles, A illuminates temporary  
as reminder. Simultaneously, the  
remaining distance or time duration is  
indicated for several seconds.  
Depending on the version, the  
distance travelled since the due date  
is indicated in the Driver Information  
Centre.  
Reset of service interval  
Control indicators  
After each service, the service  
indicator must be reset to ensure  
proper functionality. It is  
The control indicators described are  
not present in all vehicles. The  
description applies to all instrument  
versions. Depending on the  
recommended to seek the assistance  
of a workshop.  
equipment, the position of the control  
indicators may vary. When the  
ignition is switched on, most control  
indicators will illuminate briefly as a  
functionality test.  
If service is executed by yourself,  
operate as following:  
●
●
switch off ignition  
press and hold F, G or  
CHECK  
If service is required in less than  
600 miles, A flashes and then  
illuminates permanently. Remaining  
distance or time duration is indicated  
for several seconds. Simultaneously,  
the remaining distance or time  
The control indicator colours mean:  
red  
: danger, important reminder  
●
●
switch on ignition, the distance  
yellow : warning, information, fault  
green : confirmation of activation  
blue : confirmation of activation  
indication begins a countdown  
when the display indicates =0,  
release the button and  
duration is indicated for several  
seconds. Depending on the version,  
Instruments and controls  
111  
white : confirmation of activation  
grey : system paused, at least one  
system limitation has been  
detected  
Airbag and belt tensioners  
d illuminates yellow.  
When the ignition is switched on, the  
control indicator illuminates for  
several seconds. If it does not  
illuminate, does not extinguish after  
several seconds or illuminates whilst  
driving, there is a fault in the airbag  
system. Seek the assistance of a  
workshop. The airbags and belt  
pretensioners may fail to trigger in the  
event of an accident.  
See all control indicators on different  
instrument clusters 3 100.  
Turn lights  
1 flash green.  
Flash  
After the ignition has been switched  
on, a illuminates until the seat belt  
has been fastened.  
When driving faster than 12 mph and  
a seat belt is unfastened,a flashes in  
the overhead console for the  
respective seat and a chime is  
audible.  
Aditionally, a illuminates in the  
instrument cluster.  
After two minutes, the chime goes off  
and a illuminates constantly in the  
overhead console until the seat belt of  
the respective seat is fastened.  
Turn lights or the hazard warning  
flashers are activated.  
Rapid flashing: failure of a turn light or  
associated fuse, failure of turn light on  
trailer.  
Bulb replacement 3 243.  
Turn lights 3 138.  
Deployment of the belt pretensioners  
or airbags is indicated by continuous  
illumination of d.  
9 Warning  
Have the cause of the fault  
remedied immediately by a  
workshop.  
Seat belt reminder  
Belt pretensioners 3 56.  
Airbag system 3 60.  
a illuminates or flashes in the  
instrument cluster and in the  
overhead console.  
112  
Instruments and controls  
Illuminates when the engine is  
running  
Flashes when the engine is  
running  
Airbag deactivation  
Stop, switch off engine. Vehicle  
battery is not charging. Engine  
cooling may be interrupted. The  
brake servo unit may cease to be  
effective. Seek the assistance of a  
workshop.  
Fault that could lead to catalytic  
converter damage. Ease up on the  
accelerator until the flashing stops.  
Seek the assistance of a workshop  
immediately.  
Service vehicle soon  
Malfunction indicator light  
C or SERVICE illuminates yellow.  
W illuminates or flashes yellow.  
Illuminates briefly when the ignition is  
switched on.  
Illuminates when the ignition is  
switched on and extinguishes shortly  
after the engine starts.  
May illuminate together with other  
control indicators and a  
H ON illuminates yellow.  
The front passenger airbag is  
activated.  
gOFF illuminates yellow.  
The front passenger airbag is  
deactivated.  
corresponding message in the Driver  
Illuminates when the engine is  
running  
Fault in the emission control system.  
The permitted emission limits may be  
exceeded. Seek the assistance of a  
workshop immediately.  
Information Centre.  
Seek the assistance of a workshop  
immediately.  
Airbag deactivation 3 64.  
Stop engine  
STOP illuminates red.  
Charging system  
Illuminates briefly when the ignition is  
switched on.  
S illuminates red.  
Illuminates when the ignition is  
switched on and extinguishes shortly  
after the engine starts.  
Instruments and controls  
Illuminates  
113  
Illuminates together with other control  
indicators, accompanied by a warning  
chime and a corresponding message  
in the Driver Information Centre.  
Illuminates when the manual parking  
brake is applied and ignition is  
switched on 3 177.  
Electric parking brake has a fault  
3 177.  
Stop engine immediately and seek  
Electric parking brake  
9 Warning  
the assistance of a workshop.  
j illuminates or flashes red.  
Have the cause of the fault  
remedied immediately by a  
workshop.  
Illuminates  
Electric parking brake is applied  
3 177.  
System check  
X illuminates yellow.  
Illuminates together with STOP.  
Automatic operation of  
electric parking brake off  
o illuminates yellow.  
A major engine fault has been  
detected.  
Stop engine as soon as possible and  
seek the assistance of a workshop.  
Flashes  
Electric parking brake is not applied  
automatically. The application or the  
release are faulty.  
Illuminates  
Automatic operation is deactivated or  
faulty. In the event of a fault, o  
illuminates together with other control  
indicators or it is accompanied by a  
corresponding message in the Driver  
Information Centre.  
Activate automatic operation again or  
have the cause remedied by a  
workshop in the event of a fault.  
Brake system  
9 Warning  
h illuminates red.  
Have the cause of the fault  
remedied immediately by a  
workshop.  
The brake fluid level is too low.  
9 Warning  
Electric parking brake fault  
Stop. Do not continue your  
journey. Consult a workshop.  
k illuminates yellow.  
Automatic operation 3 177.  
Parking brake  
h illuminates red.  
114  
Instruments and controls  
On some vehicles with manual  
transmission, the system suggests to  
shift into neutral position, when the  
activation of the stop-start system is  
recommended.  
Flashes  
Antilock brake system  
(ABS)  
The system is actively engaged.  
Engine output may be reduced and  
the vehicle may be braked  
i illuminates yellow.  
Illuminates for a few seconds after the  
ignition is switched on. The system is  
ready for operation when the control  
indicator extinguishes.  
If i does not extinguish after a few  
seconds, or if it illuminates while  
driving, there is a fault in the ABS. The  
brake system remains operational but  
without ABS regulation.  
automatically to a small degree.  
Electronic Stability Control and  
Traction Control system 3 181.  
Selective ride control 3 182.  
Lane departure warning  
Q flashes green.  
System recognises an unintended  
lane change.  
Lane departure warning 3 211.  
Engine coolant temperature  
V or 2 illuminates red.  
If i illuminates together with h, a  
fault with the electronic brake force  
distribution has been detected.  
Stop engine immediately and seek  
the assistance of a workshop.  
Electronic Stability Control  
and Traction Control system  
J illuminates or flashes yellow.  
Illuminates when the engine is  
running  
Stop, switch off engine.  
Illuminates  
Caution  
Antilock brake system 3 176.  
A fault in the system is present.  
Continued driving is possible. Driving  
stability, however, may deteriorate  
depending on road surface  
conditions.  
Have the cause of the fault remedied  
by a workshop.  
Coolant temperature too high.  
Gear shifting  
Check coolant level immediately  
3 238.  
If there is sufficient coolant, consult a  
workshop.  
Y or Z with the number of the gear  
is indicated, when shifting is  
recommended for fuel saving  
reasons.  
Instruments and controls  
115  
Preheating  
AdBlue  
Engine oil pressure  
T illuminates red.  
z illuminates yellow.  
B flashes or illuminates yellow.  
Preheating of diesel engine is  
activated. Only activates when  
outside temperature is low. Start the  
engine when control indicator  
extinguishes.  
Illuminates when the ignition is  
Illuminates yellow  
The remaining driving range is  
between 60 miles and 1500 miles.  
switched on and extinguishes shortly  
after the engine starts.  
Illuminates when the engine is  
running  
Flashes yellow  
The remaining driving range is  
between 0 miles and 60 miles.  
AdBlue level is low. Refill AdBlue  
soon to avoid prevention of the  
engine start.  
Exhaust filter  
Caution  
+ or C illuminates yellow,  
accompanied by a message in the  
Driver Information Centre and a  
chime.  
Engine lubrication may be  
interrupted. This may result in  
damage to the engine and / or  
locking of the drive wheels.  
AdBlue 3 166.  
The exhaust filter requires cleaning.  
Continue driving until the control  
1. Select neutral gear.  
indicator extinguishes.  
Deflation detection system  
2. Move out of the flow of traffic as  
quickly as possible without  
impeding other vehicles.  
q illuminates or flashes yellow.  
Illuminates temporarily  
Illuminates  
Tyre pressure loss in one or more  
wheels. Stop immediately and check  
tyre pressure.  
Start of saturation of the exhaust filter.  
Start cleaning process as soon as  
possible by driving at a vehicle speed  
of at least 40 mph.  
3. Switch off ignition.  
Illuminates constantly  
Indication of a low additive level. Seek  
the assistance of a workshop.  
Flashes  
Fault in system. Consult a workshop.  
Deflation detection system 3 261.  
Exhaust filter 3 165.  
116  
Instruments and controls  
The charging cable is still connected  
to the vehicle. The vehicle cannot be  
started.  
Disconnect the charging cable from  
the charging port and close the  
charging port flap.  
Flashes green  
Autostop is temporarily unavailable,  
or Autostop mode is invoked  
automatically.  
9 Warning  
When the engine is off,  
considerably more force is needed  
to brake and steer. During an  
Autostop the brake servo unit will  
still be operational.  
Stop-start system 3 161.  
Exterior light  
Vehicle ready  
Do not remove key until vehicle is  
stationary, otherwise the steering  
wheel lock could engage  
unexpectedly.  
F illuminates green.  
The exterior lights are on 3 134.  
READY illuminates green. The  
vehicle is ready to be driven.  
Reduced engine power  
Low beam  
Keep engine turned off and let the  
vehicle be towed to a workshop.  
M illuminates yellow.  
D illuminates green.  
Illuminated when low beam is on.  
The charging level of the high voltage  
battery is low. Only reduced engine  
power is available.  
Low fuel  
r or 2 illuminates yellow.  
Level in fuel tank is too low.  
Refuelling 3 225.  
High beam  
A illuminates blue.  
Autostop  
Illuminates when high beam is on or  
during headlight flash 3 135.  
ñ illuminates or flashes green.  
Bleeding the diesel fuel system  
3 241.  
Illuminates green  
Engine is in an Autostop.  
High beam assist  
Charging cable connected  
B illuminates green.  
j illuminates red.  
The high beam assist is activated  
3 135.  
Instruments and controls  
117  
Cruise control 3 184.  
Additionally, a warning message is  
displayed in the Driver Information  
Centre.  
Check the reason of the deactivation  
3 199 and in case of a system fault,  
seek the assistance of a workshop.  
LED headlights  
C illuminates and a warning  
message is displayed in the Driver  
Information Centre.  
Semi-adaptive cruise  
control  
Seek the assistance of a workshop.  
Q illuminates in the Driver  
Information Centre when semi-  
Flashes  
The system is actively engaged.  
adaptive cruise control is active.  
Front fog lights  
Semi-adaptive cruise control 3 191.  
G illuminates green.  
Depending on the situation, the  
vehicle may automatically brake  
moderately or hard.  
Forward collision alert 3 197.  
Front pedestrian protection 3 201.  
Active emergency braking 3 199.  
The front fog lights are on 3 138.  
Pedestrian safety alert fault  
K illuminates yellow.  
Rear fog light  
The pedestrian safety alert is not  
working.  
H illuminates yellow.  
The rear fog light is on 3 138.  
Side blind spot alert  
T illuminates green.  
The system is active 3 205.  
Rain sensor  
Speed limiter  
y illuminates green.  
5 illuminates in the Driver  
Information Centre when speed  
limiter is active. Set speed is indicated  
alongside 5 symbol.  
Illuminated when rain sensor position  
on wiper lever is selected.  
Active emergency braking  
m illuminates or flashes yellow.  
Cruise control  
Speed limiter 3 187.  
v illuminates in the Driver  
Illuminates  
The system has been deactivated or  
a fault has been detected.  
Information Centre when speed  
limiter is active. Set speed is indicated  
in the Driver Information Centre.  
Door open  
O illuminates red.  
118  
Instruments and controls  
A door, the tailgate or the tailgate  
window is open.  
Displays  
If the vehicle is equipped with hinged  
doors, O is not illuminated when it is  
open.  
Driver Information Centre  
The Driver Information Centre is  
located in the instrument cluster.  
Driver Information Centre indicates:  
●
●
●
●
●
●
●
●
overall and trip odometer  
digital speed indication  
trip / fuel information menu  
gear shift indication  
service information  
Press button.  
vehicle and warning messages  
driver assistance messages  
pop-up messages  
Selecting menus and functions  
There are several ways to toggle  
between the respective menus and  
functions:  
Move thumb wheel upwards or  
downwards on the steering wheel.  
Instruments and controls  
119  
Baselevel instrument cluster  
Press SET 000.  
Cluster electric vehicle  
Uplevel instrument cluster  
Press F.  
Press 000.  
Press 000.  
Vehicle and service messages are  
popped up in the Driver Information  
Centre, if required. Scroll messages  
by using the above mentioned  
controls or buttons.  
Midlevel instrument cluster  
Vehicle messages 3 126.  
120  
Instruments and controls  
Display of average consumption. The  
measurement can be reset at any  
time and starts with a default value.  
To reset, press F for a few  
seconds.  
Digital display of the instantaneous  
speed.  
Stop and Start time counter  
A time counter adds up the time spent  
in Autostop during a journey.  
It resets to zero everytime the ignition  
is switched on.  
Compass  
Displays the geographic direction of  
driving.  
Trip / fuel information menu,  
baselevel display  
Average speed  
Display of average speed. The  
measurement can be reset at any  
time.  
To reset, press F for a few  
seconds.  
AdBlue range  
Press F repeatedly until the  
AdBlue menu is shown.  
Information pages:  
Fuel range  
Differerent pages with combined  
information can be selected.  
Select the required page:  
Indicates an estimate of the AdBlue  
level. A message indicates whether  
the level is sufficient or low.  
Range is calculated from current fuel  
level and current consumption. The  
display shows average values.  
After refuelling, the range is updated  
automatically after a brief delay.  
When the fuel level is low, a message  
appears on the display and the  
control indicator 2 in the fuel gauge  
illuminates 3 116.  
AdBlue 3 166.  
Trip pages:  
Trip odometer  
The recorded distance since the  
reset.  
To reset, press F for a few  
seconds.  
Average fuel consumption  
Instantaneous fuel consumption  
Display of the instantaneous  
consumption.  
Digital speed  
Instruments and controls  
121  
Display of average consumption. The  
measurement can be reset at any  
time and starts with a default value.  
To reset, press SET 000 for a few  
seconds.  
Digital display of the instantaneous  
speed.  
Stop and Start time counter  
A time counter adds up the time spent  
in Autostop during a journey.  
It resets to zero everytime the ignition  
is switched on.  
Compass  
Displays the geographic direction of  
driving.  
Trip / fuel information menu,  
midlevel display  
Average speed  
Display of average speed. The  
measurement can be reset at any  
time.  
To reset, press SET 000 for a few  
seconds.  
AdBlue range  
Information pages:  
Fuel range  
Press SET 000 repeatedly until the  
AdBlue menu is shown.  
Range is calculated from current fuel  
level and current consumption. The  
display shows average values.  
After refuelling, the range is updated  
automatically after a brief delay.  
When the fuel level is low, a message  
appears on the display and the  
control indicator 2 in the fuel gauge  
illuminates 3 116.  
Indicates an estimate of the AdBlue  
level. A message indicates whether  
the level is sufficient or low.  
Differerent pages with combined  
information can be selected.  
Select the required page:  
AdBlue 3 166.  
Trip pages:  
Trip odometer  
The recorded distance since the  
reset.  
To reset, press SET 000 for a few  
seconds.  
Average fuel consumption  
AdBlue range  
Press CHECK repeatedly until the  
AdBlue menu is shown.  
AdBlue range  
Instantaneous fuel consumption  
Display of the instantaneous  
consumption.  
Indicates an estimate of the AdBlue  
level. A message indicates whether  
the level is sufficient or low.  
Digital speed  
122  
Instruments and controls  
To reset, press 000 for a few seconds.  
Average speed  
Display of average speed. The  
measurement can be reset at any  
time.  
It resets to zero everytime the ignition  
is switched on.  
Compass  
Displays the geographic direction of  
driving.  
Trip / fuel information menu,  
uplevel display  
To reset, press 000 for a few seconds.  
AdBlue range  
Press 000 repeatedly until the AdBlue  
Information pages:  
Fuel range  
Range is calculated from current fuel  
level and current consumption. The  
display shows average values.  
After refuelling, the range is updated  
automatically after a brief delay.  
When the fuel level is low, a message  
appears on the display and the  
control indicator 2 in the fuel gauge  
illuminates 3 116.  
menu is shown.  
Indicates an estimate of the AdBlue  
level. A message indicates whether  
the level is sufficient or low.  
AdBlue 3 166.  
Trip / autonomy information  
menu, display electric vehicle  
Differerent pages with combined  
information can be selected.  
Differerent pages with combined  
information can be selected.  
Select the required page:  
Trip pages:  
Select the required page:  
Instantaneous fuel consumption  
Trip odometer  
The recorded distance since the  
reset.  
To reset, press 000 for a few seconds.  
Average fuel consumption  
Display of average consumption. The  
measurement can be reset at any  
time and starts with a default value.  
Information page:  
Average consumption of electric  
energy  
Display of average consumption. The  
measurement can be reset at any  
time and starts with a default value.  
Display of the instantaneous  
consumption.  
Digital speed  
Digital display of the instantaneous  
speed.  
Stop and Start time counter  
A time counter adds up the time spent  
in Autostop during a journey.  
To reset, press 000 for a few seconds.  
Instruments and controls  
Radio (Infotainment system)  
123  
Trip pages:  
Digital speed page  
Digital display of the instantaneous  
speed.  
Average speed  
Display of average speed. The  
measurement can be reset at any  
time.  
To reset, press 000 for a few seconds.  
Average consumption of electric  
energy  
Info Display  
The Info Display is located in the  
instrument panel near the instrument  
cluster.  
The Info Display can indicate:  
Display of average consumption. The  
measurement can be reset at any  
time and starts with a default value.  
To reset, press 000 for a few seconds.  
Trip odometer  
The recorded distance since the  
reset.  
To reset, press 000 for a few seconds.  
●
●
●
●
time 3 98  
outside temperature 3 98  
date 3 98  
Infotainment system, see  
description in the Infotainment  
Manual  
Press ) to switch on the display.  
Press MENU to select main menu  
page.  
Press fYZg to select a menu  
page.  
Press OK to confirm a selection.  
●
●
●
●
●
indication of rear view camera  
3 210  
Traffic sign assistant page  
Displays recognised traffic signs.  
indication of panoramic view  
system 3 207  
navigation, see description in the  
Infotainment Manual  
vehicle and system messages  
3 126  
settings for vehicle  
personalisation 3 127  
Press 1 to exit a menu without  
changing a setting.  
Flow page  
Displays the current energy flow  
within the electric system.  
Compass page  
Displays the geographic direction of  
driving.  
124  
Instruments and controls  
Touch required menu display icon or  
a function with the finger.  
Confirm a required function or  
selection by touching.  
Touch 3 or & on the display to exit  
a menu without changing a setting.  
For further information, see  
Infotainment Manual.  
Different colours show the engery  
flow.  
Multimedia / Multimedia Navi  
Selecting menus and settings  
There are three options to operate the  
display:  
●
●
green: electric engine operating  
blue: regenerating energy  
Average consumption  
This menu displays the average  
power consumption during the  
current trip.  
●
●
via buttons next to the display  
by touching the touchscreen with  
the finger  
●
via speech recognition  
●
●
green: electric energy consumed  
Speech recognition  
Description see Infotainment Manual.  
Button and touch operation  
blue: electric energy generated  
from the braking and  
Flow  
deceleration phases of the  
vehicle used to recharge the high  
voltage battery  
This menu displays the current  
energy flow within the electric system.  
The current trip is subdivided into time  
steps. For each time step, the  
average consumption is displayed.  
The time steps can be modified.  
Press ) to switch on the display.  
Press : to select system settings  
(units, language, time and date).  
Press _ to select vehicle settings or  
driving functions.  
1. Press m.  
2. Select Flow.  
Instruments and controls  
125  
plane directly ahead in driver's view.  
The image appears focused out  
toward the front of the vehicle.  
1. Press m.  
2. Select Statistics.  
Switching on  
Press § to switch on the head-up  
display.  
3. Press + and - to modify the time  
steps.  
Head-up display shows:  
Adjust position of head-up display  
image  
Press 7 or 8 to centre the image.  
It can only be adjusted up and down,  
not side to side.  
●
●
vehicle speed  
speed limits detected by the  
speed sign recognition  
set speed of speed limiter  
set speed of cruise control  
forward collision alert  
Vehicle personalisation 3 127.  
Head-up display  
●
●
●
●
The head-up display displays driver  
information concerning the  
instrument cluster onto a foldable  
9 Warning  
projection plane on the driver's side.  
navigation information.  
The information appears as an image  
projected from a lense in the  
instrument panel onto the projection  
If the head-up display image is too  
bright or too high in your field of  
view, it may obstruct your view  
126  
Instruments and controls  
Units  
when it is dark outside. Be sure to  
keep the head-up display image  
dim and placed low in your field of  
view.  
Vehicle messages  
Messages are indicated in the Driver  
Information Centre, in some cases  
together with a warning chime.  
Units can be changed in vehicle  
personalisation menu 3 127.  
Care of head-up display  
Adjust brightness  
Clean the screen of the head-up  
display with a soft cloth sprayed with  
glass cleaner. Wipe the lens gently,  
then dry it.  
The head-up display image will  
automatically dim and brighten to  
compensate for outside lighting.  
Brightness can also be adjusted  
manually as needed:  
System limitations  
Press § to brighten the display.  
Press $ to dim the display.  
Head-up display may not operate  
properly when:  
●
The lens in the instrument panel  
is covered by objects or not  
clean.  
The image can temporarily light up  
depending on angel and position of  
sunlight.  
●
●
●
Display brightness is too dim or  
Switching off  
Press $ and hold to turn the head-up  
display off.  
Press to confirm a message.  
bright.  
Image is not adjusted to the  
proper height.  
The driver wears polarized  
sunglasses.  
Vehicle and service messages  
The vehicle messages are displayed  
as text. Follow the instructions given  
in the messages.  
Language  
Preferred language can be set in  
vehicle personalisation menu 3 127.  
If the head-up image is not correct for  
other reasons, contact a workshop.  
Instruments and controls  
127  
●
●
If an unintended lane change  
occurs.  
If the exhaust filter has reached  
the maximum filling level.  
Messages in the Info Display  
Vehicle personalisation  
The vehicle's behaviour can be  
personalised by changing the settings  
in the Info Display.  
Depending on vehicle equipment and  
country-specific regulations some of  
the functions described below may  
not be available.  
Some important messages may  
appear additionally in the  
Info Display. Some messages only  
pop-up for a few seconds.  
When the vehicle is parked and /  
or the driver's door is opened  
●
Warning chimes  
With exterior lights on.  
If several warnings appear at the  
same time, only one warning chime  
will sound.  
During an Autostop  
●
●
Some functions are only displayed or  
active when the engine is running.  
If the driver's door is opened.  
If any condition for a restart of the  
engine is not fulfilled.  
When starting the engine or whilst  
driving  
Radio (Infotainment system)  
●
●
If a seat belt is not fastened.  
If a door or the tailgate is not fully  
closed.  
●
●
●
●
●
If a certain speed is exceeded  
with parking brake applied.  
If a programmed speed or speed  
limit is exceeded.  
If a warning message appears in  
the Driver Information Centre.  
If the electronic key is not in the  
passenger compartment.  
Press MENU to open the menu page.  
Use the arrow buttons to operate the  
display:  
If the parking assist detects an  
object.  
128  
Instruments and controls  
Select Personalisation-configuration  
●
●
Comfort  
Multimedia  
I OK.  
Ambient lighting: Adjusts the  
brightness of the ambient  
lighting.  
Rear wiper in reverse gear:  
Activates or deactivates  
automatic switching on of the  
rear window wiper when reverse  
gear is engaged.  
Unit settings  
Select Display configuration I OK.  
Select Choise of units I OK.  
Select desired settings I OK.  
Language settings  
Select Display configuration I OK.  
Select Choise of language I OK.  
Select desired language I OK.  
Vehicle  
Unlocking boot only: Activation /  
deactivation.  
Plip action: Driver / all doors.  
Security  
Fatigue Detection system:  
Activates or deactivates the  
driver drowsiness system.  
Vehicle settings  
Press : to open settings menu.  
●
●
Select Define vehicle parameters I  
OK.  
Unit settings  
Select System configuration.  
Change units for Distance and fuel  
consumption and Temperature.  
In the corresponding submenus the  
following settings can be changed:  
Driving assistance  
●
Lamps  
Speed recommendation:  
Activates or deactivates the  
function.  
Follow me home headlamps:  
Activates or deactivates the  
function and adjusts its duration.  
Welcome lighting: Activates or  
deactivates the function and  
adjusts its duration.  
Language settings  
Select Language.  
Change language by touching the  
respective entry.  
Driving function  
Press _.  
Select Driving function.  
Directional headlights: Activates  
or deactivates the function.  
Instruments and controls  
129  
In the corresponding submenus the  
following settings can be changed:  
●
●
Type the new speed value via the  
keypad and confirm with A /  
OK.  
Confirm with A / OK once more  
to exit the menu.  
Welcome lighting: Activates or  
deactivates the function and  
adjusts its duration.  
●
Parking sensors: Activates or  
deactivates the parking assist  
sensors.  
Directional headlamps: Activates  
or deactivates the cornering  
lights.  
●
●
Blind spot sensors: Activates or  
Vehicle settings  
Press _.  
Select Vehicle settings.  
In the corresponding submenus the  
following settings can be changed:  
●
deactivates side blind spot alert.  
●
●
Comfort  
Under-inflation initialization:  
Initialises the tyre under-inflation  
detection system.  
Mood lighting: Adjusts the  
brightness of the ambient  
lighting.  
●
Diagnostic: Shows alert  
messages of the diagnostic  
system.  
Safety  
Parking  
Speed reading/recommendation:  
Activates or deactivates the  
speed limit information by traffic  
sign recognition.  
Active safety brake: Activates or  
deactivates active emergency  
braking, the alert distance for risk  
of collision can be selected.  
Mirror adaptation in reverse:  
Adjusts the exterior mirrors if  
reverse gear is engaged to  
facilitate pavement visibility.  
Driver's attention warning:  
Activates or deactivates the  
driver drowsiness system.  
Prevention of door mirror folding:  
Activates or deactivates the  
automatic folding of the exterior  
mirrors.  
Rear wiper in reverse: Activates  
or deactivates automatic  
switching on of the rear window  
wiper when reverse gear is  
engaged.  
Memorising of preset speeds  
This feature enables to define and  
memorise up to six speed settings for  
cruise control and speed limiter. By  
default, a few speeds are already  
memorised.  
●
●
●
Press _.  
Select Adjusting speeds.  
Select Cruise control or Speed  
limiter.  
●
Headlights  
Guide-me-home lighting:  
Activates or deactivates the  
function and adjusts its duration.  
●
Select the speed setting to be  
changed.  
130  
Instruments and controls  
Driving functions  
●
●
Under-inflation initialization:  
Initialises the tyre under-inflation  
detection system.  
Diagnostic: Shows alert  
messages of the diagnostic  
system.  
Multimedia Navi  
Press _.  
Select Driving functions.  
In the corresponding submenus the  
following settings can be changed:  
●
●
Automatic headlamp dipping:  
Activates or deactivates high  
beam assist.  
Lane departure warning system:  
Activates or deactivates lane  
departure warning.  
Memorising of preset speeds  
This feature enables to define and  
memorise up to six speed settings for  
cruise control and speed limiter. By  
default, a few speeds are already  
memorised.  
●
●
●
●
●
Stop and start: Activates or  
Press _.  
Select Adjusting speeds.  
Select Cruise control or Speed  
limiter.  
deactivates stop-start system  
Press : to open settings menu.  
Cruise control active: Activates or  
deactivates semi-adaptive cruise  
control.  
Unit settings  
Select System settings in the options  
●
Parking sensors: Activates or  
deactivates the parking assist  
sensors.  
menu.  
Change units for Distance and fuel  
consumption and Temperature.  
Confirm with A / OK.  
●
●
Blind spot sensors: Activates or  
deactivates side blind spot alert.  
Language settings  
Select Languages.  
Change language by touching the  
respective entry.  
Traction control: Activates or  
deactivates Traction Control  
system.  
Confirm with A / OK.  
Instruments and controls  
131  
●
●
Select the speed setting to be  
changed.  
Type the new speed value via the  
keypad and confirm with A /  
OK.  
Confirm with A / OK once more  
to exit the menu.  
Welcome lighting: Activates or  
deactivates the function and  
adjusts its duration.  
Directional headlamps: Activates  
or deactivates the cornering  
lights.  
Driver's attention warning:  
Activates or deactivates the  
driver drowsiness system.  
●
●
●
●
Vehicle access  
Hands-free auto locking:  
Activates or deactivates the  
function.  
Vehicle settings  
Press _.  
Select Vehicle settings.  
In the corresponding submenus the  
following settings can be changed:  
●
Comfort  
Mood lighting: Adjusts the  
brightness of the ambient  
lighting.  
Parking  
Safety  
Rear wiper in reverse: Activates  
or deactivates automatic  
switching on of the rear window  
wiper when reverse gear is  
engaged.  
Traffic Signs Recognition:  
Activates or deactivates the  
speed limit information by traffic  
sign recognition.  
Blocking of door mirror folding:  
Activates or deactivates the  
automatic folding of the exterior  
mirrors.  
Active safety brake: Activates or  
deactivates active emergency  
braking, the alert distance for risk  
of collision can be selected.  
●
Headlights  
Mirror adaptation in reverse:  
Adjusts the exterior mirrors if  
reverse gear is engaged to  
facilitate pavement visibility.  
Guide-me-home lighting:  
Activates or deactivates the  
function and adjusts its duration.  
132  
Instruments and controls  
Notice  
Status LED  
Telematics services  
Establishing an emergency call may  
not be possible in areas without  
sufficient network availability or due  
to hardware damage during an  
accident.  
Illuminates green for three seconds  
when the ignition is switched on: the  
system works properly.  
Vauxhall Connect  
Vauxhall Connect is a new way to  
stay connected and secure on the  
road.  
Illuminates red: fault in the system.  
Contact a workshop.  
Flashes red: backup battery needs  
replacement.  
Automatic crash notification  
In case of an accident with airbag  
deployment, an automatic  
emergency call is established and an  
automatic crash notification will be  
transmitted to the next public safety  
answering point.  
Features available with  
Vauxhall Connect are:  
●
●
emergency call function  
breakdown call function  
Breakdown call function  
Pressing . for more than two  
seconds connects you to a roadside  
assistance service provider.  
For information about coverage and  
scope of services of the roadside  
assistance, please refer to the  
Service and warranty booklet.  
When the vehicle is equipped with  
Vauxhall Connect, these features are  
automatically activated. Terms and  
Conditions apply.  
Vauxhall Connect is operated by the  
buttons in the overhead console.  
Emergency assistance  
In case of an emergency you can also  
manually place an emergency call by  
pressing the red SOS button for more  
than two seconds. The LED flashes to  
confirm that a connection to the  
nearest PSAP is being established.  
The LED illumates steadily as long as  
the call is active.  
Emergency call function  
Vehicles featuring the emergency call  
function are equipped with a red  
SOS button in the overhead console.  
The emergency call function will  
establish a connection to the nearest  
public safety answering point (PSAP).  
A minimum set of data including  
vehicle and location information will  
be sent to the PSAP.  
ERA GLONASS  
ERA GLONASS is a manually or  
automatically actuated emergency  
service. Emergency centres provide  
assistance and information during an  
emergency.  
Pressing the SOS button immediately  
a second time will terminate the call.  
The LED switches off.  
In case of an accident with an impact  
of appropriate severity, an  
emergency call is placed  
automatically, regardless of airbag  
Instruments and controls  
133  
activation. An immediate connection  
with an advisor will be established  
who will check whether help is  
needed.  
To cancel the call, press the SOS  
button again. The green LED goes  
out. The voice message confirms the  
cancellation.  
Control buttons  
Status LED  
9 Danger  
The system provides feedback via  
voice messages and an LED.  
Green : The system is activated. A  
connection to an operator  
is on duty.  
The service is only available for  
markets where it is legally required  
and activated. Furthermore, the  
manual and the automatic  
emergency call function depend  
on the availability of the  
Red  
: The system is booting up  
after switching on ignition,  
the LED goes out after 3  
seconds. If the LED stays  
red, a malfunction has  
been detected in the  
system. An emergency  
call may not work. Contact  
a workshop immediately.  
: The internal backup  
battery is defective.  
SOS button  
In an emergency situation press and  
hold SOS button for more than 2  
seconds.The green LED and the  
voice message will confirm that the  
call has been sent to the emergency  
centre.  
emergency centres and the  
infrastructure in the country.  
Notice  
In order to be available and  
operational, the system requires  
functioning vehicle electrics, mobile  
service and GLONASS satellite link.  
Depending on equipment, a backup  
battery is used.  
The green LED illuminates when the  
service connection is established. It  
will go out when the connection is  
complete.  
A minimum set of data is transferred  
to the emergency centre, including  
such data as car location, car model,  
vehicle identification number. The  
operator will contact you and, if  
necessary, send rescue workers from  
the relevant support services.  
Red  
flashing  
Contact a workshop  
immediately.  
Seek the assistance of a workshop if  
the LED does not illuminate after  
switching on the ignition.  

Related Topics

Controls
Warning lights, gauges and indicators
Displays
Vehicle messages
Warning chimes
Vehicle personalisation
Telematics services

Popular Owner Manuals

Audi
BMW
Citroen
Ford
Honda
Peugeot

Latest Owner Manuals

Twelfth Generation (2018-2026) Toyota Corolla 4 Door Twelfth Generation (2018-2026) Toyota Corolla 4 Door
Ninth Generation (2007-2012) Toyota Corolla 4 Door Ninth Generation (2007-2012) Toyota Corolla 4 Door
Fourth Generation (2021-2026) Toyota Yaris 4 Door Fourth Generation (2021-2026) Toyota Yaris 4 Door
Third Generation (2011-2020) Toyota Yaris 4 Door Third Generation (2011-2020) Toyota Yaris 4 Door
Second Generation (2006-2011) Toyota Yaris 4 Door Second Generation (2006-2011) Toyota Yaris 4 Door
First Generation (1999-2005) Toyota Yaris 4 Door First Generation (1999-2005) Toyota Yaris 4 Door