2017-2024 Volkswagen Arteon 4 Door Driver information User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Driver information for Your Volkswagen Arteon 4 Door First Generation (2017-2024)

Driver information  
Symbols in the instrument cluster  
The warning and indicator lights can turn on individually or in combination with each other and indicate warnings, malfunctions and certain functions. Some warning  
and indicator lights come on when you switch the ignition on and must turn off after some time.  
Indicator lights that turn on in the light switch are described in the “Lights” chapter ⇒ Switching the lights on and off .  
WARNING  
Failure to respond to illuminated warning lights and messages may result in a vehicle breakdown, accidents and serious injuries or death.  
Never ignore illuminated warning lights and messages.  
Stop the vehicle as soon as it is safe to do so.  
Do not continue driving!  
Central warning light ⇒ Priority 1 warning message  
Fasten safety belt ⇒ Fasten seat belts reminder and seat belt safety indicator  
Electronic parking brake switched on ⇒ Electronic parking brake  
Holding force of the electronic parking brake too low ⇒ Holding force in the current situation is too low  
Do not continue driving!  
Brake system malfunction ⇒ Brake system malfunction  
Do not continue driving!  
Electromechanical brake booster failed ⇒ Electromechanical brake servo failure  
Do not continue driving!  
Brake fluid level too low ⇒ Brake fluid level  
Check brake system ⇒ Brake pad wear indicator  
Take over steering and be ready to brake. ⇒  
Introduction  
Do not continue driving!  
Engine oil level too low ⇒ Engine oil level very low  
Do not continue to drive!  
Engine oil pressure too low ⇒ Engine oil pressure too low  
Do not continue to drive!  
Engine coolant system malfunction ⇒ Engine coolant  
Do not continue driving!  
Steering malfunction ⇒ Steering malfunction  
Rear Traffic Alert has detected an obstacle to the rear ⇒ Rear Traffic Alert  
Do not continue driving!  
12 V energy supply malfunction ⇒ 12-volt power supply  
Collision warning ⇒ Warning levels and braking support  
13  
Take over the steering immediately ⇒ Take over the steering immediately  
Do not continue to drive!  
Transmission overheating ⇒ Transmission overheating  
Central warning light ⇒ Priority 2 warning message  
Airbag or safety belt pretensioner system deactivated with diagnostic equipment ⇒ Airbag or safety belt pretensioner system deactivated  
with diagnostic equipment  
Airbag system or safety belt pretensioner malfunction ⇒ Airbag system or safety belt pretensioners malfunction  
Front passenger's front airbag deactivated ⇒ Front passenger's front airbag switched off  
Emergency Call Service limited ⇒ Emergency Call Service limited  
Emergency Call Service malfunctioning ⇒ Emergency Call Service malfunction  
Electronic parking brake malfunction ⇒ Electronic parking brake malfunction  
Comes on: Electronic Stability Control (ESC) malfunction ⇒ ESC malfunction  
Flashes: Electronic Stability Control (ESC) or Anti-slip regulation (ASR) in operation ⇒ Electronic Stability Control (ESC)  
Electronic Stabilization Control (ESC) switched off ⇒ ESC Off  
Anti-Slip Regulation (ASR) switched off ⇒ ASR  
Anti-Lock Braking System (ABS) malfunction ⇒ ABS failure or malfunction  
Engine oil system malfunction ⇒ Engine oil system malfunction  
Engine oil level too low ⇒ Engine oil level too low  
Engine oil level too high ⇒ Engine oil level too high  
Engine oil system malfunction ⇒ Engine oil system malfunction  
Tank almost empty ⇒ Fuel tank almost empty  
Travel Assist not available ⇒ Comfort drive Travel Assist is not available or is not working as expected  
Tank cap not closed ⇒ Fuel tank cap open  
Driving light failure ⇒ Exterior lighting malfunction  
Rain/light sensor malfunction ⇒ Rain/light sensor malfunction, ⇒ Rain/light sensor malfunction  
Windshield wiper malfunction ⇒ Windshield wiper malfunction  
Washer fluid level too low ⇒ Washer fluid level too low  
14  
Steering malfunction ⇒ Steering malfunction  
Do not continue to drive!  
Tire pressure low ⇒ Tire pressure low  
Do not continue to drive!  
Tire pressure monitoring system malfunction ⇒ Tire pressure monitoring system malfunction  
Front Assist is switched off ⇒ Using Front Assist  
Autonomous Emergency Braking starts ⇒ Front Assist Starts  
Cruise control system malfunction ⇒ Cruise control system malfunction  
Speed warning ⇒ Driving data menu  
Adaptive cruise control (ACC) not available ⇒ ACC is not available  
Semi-automatic vehicle control in a medical emergency (Emergency Assist) is functioning ⇒ Driving with Emergency Assist  
Lane Assist in control ⇒ Driving with Lane Assist  
Side Assist malfunction ⇒ Lane change system malfunctioning  
Rear Traffic Alert brakes ⇒ Rear Traffic Alert  
Engine control malfunction ⇒ Engine control malfunction  
Exhaust system malfunction ⇒ Exhaust-related malfunction  
Particulate filter clogged with soot ⇒ Particulate filter clogged with soot  
Engine RPM limited ⇒ Engine speed limited  
12-volt power supply malfunction ⇒ 12-volt power supply  
Transmission malfunction ⇒ Transmission overheating  
Adaptive chassis control (DCC) malfunction ⇒ Adaptive chassis control malfunction  
Vehicle key not in vehicle ⇒ Valid vehicle key cannot be detected  
Press the brake pedal. ⇒ The engine is not starting  
Turn signals ⇒ Turn signal indicator light  
Trailer turn signal ⇒ Trailer turn signal indicator light  
Cruise control switched on, regulation active ⇒  
Lane Assist active ⇒ Driving with Lane Assist  
Introduction  
Comfort drive Travel Assist active ⇒  
Introduction  
15  
Adaptive Cruise Control (ACC) regulates, no vehicle driving ahead is detected ⇒ Switching ACC on and off  
Adaptive Cruise Control (ACC) regulates, vehicle driving ahead is detected ⇒ Switching ACC on and off  
High beams or headlight flasher ⇒ Switching the high beam headlights on and off  
Outside temperature is below +39 °F (+4 °C) ⇒ Volkswagen Digital Cockpit Pro Information Displays  
Start/Stop system active ⇒ Start-stop system  
Start/Stop system not available ⇒ Start-stop system  
Economical driving condition ⇒ Volkswagen Digital Cockpit Pro Information Displays  
Service due ⇒ Service interval display  
Travel Assist active, Adaptive Cruise Control active and adaptive lane guidance inactive  
High beam control active ⇒ Switching on Light Assist  
Take over the steering ⇒ Take over the steering  
⇒
Introduction  
Autonomous Emergency Braking starts ⇒ Front Assist Starts  
Distance warning ⇒ Warning levels and braking support  
Eco driving mode ⇒ Driving mode properties  
Comfort driving mode ⇒ Driving mode properties  
Normal driving mode ⇒ Driving mode properties  
Individual driving mode ⇒ Driving mode properties  
Sport driving mode ⇒ Driving mode properties  
Mobile phone connected via Bluetooth® ⇒ Volkswagen Digital Cockpit Pro Information Displays  
Mobile phone battery charge level ⇒ Volkswagen Digital Cockpit Pro Information Displays  
Note about information in the Owner's Manual ⇒ Note about information in the Owner's Manual  
Warning and information texts  
The status of some functions inside the vehicle and vehicle components are checked when the ignition is switched on or while driving. Malfunctions are indicated by  
red and yellow warning symbols in the instrument cluster display and may also be signaled audibly in some cases. The appearance of texts and symbols may vary  
depending on the instrument cluster version.  
Any malfunctions currently occurring can also be manually called up. To do this, open the Vehicle status or Vehicle menu. ⇒ Vehicle settings menu  
Priority 1 warning message  
The red central warning light flashes or comes on, in some cases together with warning tones or additional symbols.  
Do not continue driving! There is a haza  
Check the malfunction. Contact an authorized Volkswagen dealer or authorized Volkswagen Service Facility immediately for assistance.  
Priority 2 warning message  
16  
The yellow central warning light flashes or comes on, in some cases together with warning tones or additional symbols. Malfunctions or insufficient operating fluids  
can cause vehicle damage and vehicle malfunctions. Check the malfunction as soon as possible. Immediately contact an authorized Volkswagen dealer or  
authorized Volkswagen Service Facility to have the system checked. Volkswagen recommends contacting an authorized Volkswagen dealer or authorized  
Volkswagen Service Facility.  
Note about information in the Owner's Manual  
You can find more information about the existing warning message in the Owner's Manual.  
Informational text  
Information about various processes in the vehicle.  
If there are multiple warning messages, the symbols will appear consecutively for several seconds. The symbols will appear until the malfunction is corrected.  
If warning messages about malfunctions appear when the ignition is switched on, settings or information displays may not appear as described. If the  
malfunction persists, contact a suitably qualified professional. Volkswagen recommends contacting an authorized Volkswagen dealer or authorized Volkswagen  
Service Facility.  
Introduction to the instrument cluster  
The vehicle is equipped with a Volkswagen Digital Cockpit. The instrument cluster shows essential information, such as speed.  
In addition, the following functions, among others, are available depending on the equipment:  
Various menus, such as for the driver assistance systems.  
Status displays for the driver assistance systems.  
Display messages.  
Warning and indicator lights.  
Information about economy and range.  
Content can be individually adapted and settings can be changed in the menus.  
WARNING  
If the driver is distracted while driving, accidents and serious injuries can occur.  
Never operate the instrument cluster while driving.  
Only adjust any settings in the instrument cluster or Infotainment system when the vehicle is stationary.  
WARNING  
If there is a serious fault in the instrument cluster, the display may be turned off. The warning light  
Safely stop the vehicle.  
may also come on here.  
See an authorized Volkswagen dealer or authorized Volkswagen Service Facility for assistance.  
After starting the engine when the 12 V vehicle battery is severely drained or when it has been replaced or jump-started, the system settings, e.g. personal  
convenience settings and programming, and user profiles may be changed or erased. Check and correct the settings after the 12 V vehicle battery is sufficiently  
recharged.  
Volkswagen Digital Cockpit Pro  
Overview of the Volkswagen Digital Cockpit Pro  
The Volkswagen Digital Cockpit Pro is a digital instrument cluster with a high-resolution TFT color display. By selecting different information profiles, other displays  
can be shown in addition to the standard dials, such as the tachometer. The term Volkswagen Digital Cockpit Pro is used to refer to the “Pro digital instrument  
cluster” in the following.  
17  
Fig. 9 Volkswagen Digital Cockpit Pro in the instrument panel (general example).  
Tachometer (RPM of the running engine).  
Currently engaged gear or selector lever level ⇒ Driving.  
Displays ⇒ Operating the Volkswagen Digital Cockpit Pro .  
Speedometer.  
Digital speed display.  
Operating the Volkswagen Digital Cockpit Pro  
Fig. 10 Right side of the multi-function steering wheel: Operating the Volkswagen Digital Cockpit Pro (variant 1).  
18  
Fig. 11 Right side of the multi-function steering wheel: Operating the Volkswagen Digital Cockpit Pro (variant 2).  
Vehicles with multi-function steering wheel: Menus cannot be accessed when a priority 1 warning message is displayed → page , Warning and information texts.  
You can confirm and hide some messages using the  
button on the multi-function steering wheel fig. 10, fig. 11.  
Selecting a menu or information display  
Vehicles with multi-function steering wheel:  
1. Switch the ignition on.  
2. If a message or vehicle icon is displayed, press the  
button, repeatedly if necessary.  
3. To display a menu and to scroll through the menu, press the  
or  
button.  
4. To open the displayed menu or information display, press the  
seconds.  
button or wait until the menu or the information display opens automatically after several  
Applying settings in the menus  
Vehicles with multi-function steering wheel:  
1. Press the  
or  
arrow button in the displayed menu until the preferred menu item is highlighted.  
The item is marked with a frame around it.  
2. Press the  
A check mark  
button to apply the desired changes.  
indicates that the respective function is switched on.  
3. To return to the menu selection, press the  
or  
button.  
VIEW button on multi-function steering wheel  
You can use the  
button to switch between the classic display of dials, the large platform without information profiles, and the enhanced view with highlighted  
information profiles. The classic display shows the large dials on the right and left side, and the selected information profile is displayed in the center.  
1. Press and hold the  
button to select from the preset information profiles in the list:  
Classic View without information profiles.  
Automatic The information profiles adjust to the selected driving mode. Only for vehicles with Driving Mode Selection.  
Preset 1 Individual selection of information profiles  
19  
Preset 2 Individual selection of information profiles  
Preset 3 Only on vehicles with standard factory-installed navigation system.  
Navigation map in the Volkswagen Digital Cockpit Pro  
Depending on the vehicle equipment, the Volkswagen Digital Cockpit Pro may display a detailed navigation map.  
The navigation map can be displayed in three sizes. With the larger map view, the navigation map is shown across the entire display. To select the desired map  
size, proceed as follows:  
1. Select menu item Navigation.  
2. Press the  
3. Press the  
button on the multi-function steering wheel to switch between the map sizes.  
arrow buttons on the multi-function steering wheel to zoom in or out.  
or  
4. When zooming manually, press the  
button on the multi-function steering wheel to switch to auto-zoom.  
Depending on the equipment, navigation will be shown on two screens or only on one screen. The navigation map may appear in the Volkswagen Digital Cockpit  
Pro and in the Infotainment system or just in the Infotainment system. If the navigation map is shown in the Infotainment system, only navigation arrows are shown  
the Volkswagen Digital Cockpit.  
If warning messages about malfunctions appear when the ignition is switched on, settings or information displays may not appear as described. If the  
malfunction persists, contact a suitably qualified professional. Volkswagen recommends contacting an authorized Volkswagen dealer or authorized Volkswagen  
Service Facility.  
WARNING  
If the driver is distracted while driving, accidents and serious injuries can occur.  
Never operate the Volkswagen Digital Cockpit Pro while driving.  
Only adjust any settings in the Volkswagen Digital Cockpit Pro or Infotainment system when the vehicle is stationary.  
Volkswagen Digital Cockpit Pro Information Displays  
Information profiles  
Using the Volkswagen Digital Cockpit menu item in the Infotainment system vehicle settings, you can select different, topic-specific information profiles ⇒ Vehicle  
settings menu. Depending on the selected information profile, the Volkswagen Digital Cockpit Pro may show additional information in the center of the dials or the  
dials may be hidden and the additional information shown across the entire display. The following information profiles can be selected:  
Audio. Digital display of the current audio playback  
Comfort drive Travel Assist. Visual display of various driver assistance systems ⇒ Driver assistance systems.  
Distance Display of the distance driven.  
Gear indicator Display of the current gear or the selected gear.  
Speed Display of the speed.  
Navigation Graphic display of arrow navigation  
Range. Display of the range.  
Consumption Graphic display of the current consumption and the digital display of the average consumption  
Traffic sign recognition Display of detected traffic signs.  
Destination arrival information. Display of remaining driving time, the distance to the destination, and the estimated arrival time.  
Depending on the equipment, the number and scope of the information profiles that can be selected may vary.  
Possible displays in the Volkswagen Digital Cockpit Pro  
Depending on the vehicle equipment, different information may be shown in the Volkswagen Digital Cockpit Pro:  
Outside temperature display.  
Detected road sign from the traffic sign recognition.  
Driver assistance systems.  
Driving data menu and menus for various settings.  
Speed warnings.  
Speed warning for winter tires.  
Open doors, hood and trunk lid.  
Infotainment system and navigation information.  
Odometer displays.  
20  
Compass display.  
Radiator fan run-on.  
Engine code ().  
Service interval display.  
Status display for the start-stop system ⇒ Start/Stop system.  
Phone information.  
Time.  
Selector lever position.  
Warning and information texts.  
Warning and indicator lights ⇒ Symbols in the instrument cluster.  
Depending on the vehicle equipment: Fuel-efficient driving  
. Status display for Active Cylinder Management (ACT ) ⇒ Eco tips.  
Outside temperature display  
When outside temperatures are colder than approximately +4°C (+39°F), a snowflake symbol also appears on the outside temperature display  
remains on until the outside temperature rises above +43 °F (+6 °C).  
. This symbol  
In the following situations, the temperature displayed may be higher than the actual outside temperature due to heat radiating from the engine:  
When the vehicle is stationary  
When the driving speed is very low  
The measurement range is from -45 °C (-49 °F) to +169 °F (+76 °C)  
WARNING  
Streets and bridges may be icy when outside temperatures are above the freezing point.  
The  
snowflake symbol indicates a possible risk of black ice.  
Black ice may also be present when outside temperatures are above +39 °F (+4 °C) when the  
Never rely solely on the outside temperature display.  
snowflake symbol is not displayed.  
Open doors, hood and trunk lid  
If, after unlocking the vehicle and while driving, any doors and/or the hood or trunk lid are open, this is displayed in the Volkswagen Digital Cockpit and an audible  
signal may also sound.  
Speed warning for winter tires  
If the set maximum speed is exceeded, this will be shown in the digital instrument cluster.  
Settings for the speed warning can be adjusted in the vehicle settings in the Infotainment system ⇒ Winter tires.  
Compass display  
When the ignition is switched on, the instrument cluster display shows an abbreviation to indicate the direction the vehicle is currently traveling, for example “NW”  
for northwest.  
If the Infotainment system is switched on and route guidance is not active, the graphic display of a compass is also available.  
Odometer displays  
The odometer registers the total distance that the vehicle has driven.  
The trip trip odometer shows the miles that were driven since the trip odometer was last reset.  
1. Reset the odometer via the Infotainment system or the service menu ⇒ Service menu.  
Radiator fan run-on  
This indicator appears after the ignition has been switched off, if the radiator fan continues to run.  
The radiator fan may continue running due to:  
Exhaust gas post-treatment, through particulate filter regeneration, for example.  
Active brake cooling after descent.  
Dissipation of engine heat after high load, e.g. trailer mode.  
Engine code  
1. Open the service menu ⇒ Service menu.  
21  
2. Select the Engine code menu item.  
Phone information  
If a cell phone is connected via Bluetooth, the Bluetooth symbol  
The symbol also indicates the charge level of the mobile device.  
will be displayed in the Volkswagen Digital Cockpit.  
Selector lever position  
The selector lever position that is engaged is shown on the left side of the selector lever and in the Volkswagen Digital Cockpit.  
If necessary, the respective gear is displayed in the Volkswagen Digital Cockpit when in the D/S selector lever position and when in tiptronic mode ⇒ Automatic  
transmission: selecting the selector lever position.  
Fuel-efficient driving  
If the vehicle is driving in a fuel-efficient manner, this will be indicated in the Volkswagen Digital Cockpit while driving  
.
Suitably qualified professionals can program or modify additional functions depending on the vehicle equipment. Volkswagen recommends contacting an  
authorized Volkswagen dealer or authorized Volkswagen Service Facility.  
There are different instrument clusters; therefore the versions and appearances of the displays may vary. Malfunctions will only be indicated by indicator lights  
if the display does not have warning or information texts.  
Some displays in the Volkswagen Digital Cockpit may be hidden due to events that occur suddenly, e.g. incoming phone calls.  
Depending on the equipment, some settings and displays may also appear in the Infotainment system.  
Tachometer  
The start of the red area on the tachometer indicates the maximum permissible engine speed for all gears when the engine is run in and at operating temperature.  
Before reaching the red area, shift to the next highest gear, select the selector lever position D/S or take your foot off the accelerator pedal.  
NOTICE  
Avoid high engine speeds, full acceleration and heavy engine loads when the engine is cold.  
To prevent engine damage, the tachometer indicator may only be in the red area of the scale briefly.  
Shifting up early helps save fuel and reduce operating noises.  
Fuel gauge  
Digital fuel gauge  
Fig. 12 Fuel gauge on the Volkswagen Digital Cockpit Pro (general example).  
WARNING  
22  
Driving with low fuel level that is too low can lead to a vehicle breakdown in traffic, accidents, and serious injuries.  
If the fuel level is too low, this can result in irregular fuel supply to the engine, particularly when going uphill or downhill.  
The steering, all driver assistance systems and brake support systems will not work if the engine is “sputtering” or cuts out due to fuel shortage or  
irregular fuel supply.  
To prevent vehicle breakdown due to low fuel, always refill the fuel tank once it reaches a fill level of 1/4.  
NOTICE  
Never drive with a completely empty fuel tank. Irregular fuel supply can result in misfiring and unburnt fuel entering the exhaust system.  
The small arrow next to the fuel pump symbol on the fuel gauge indicates which side of the vehicle the fuel filler flap is on.  
Troubleshooting  
Fuel tank almost empty  
The yellow indicator light turns on. The reserve supply (red marking ) is being used.  
1. Refuel at the next opportunity.  
Fuel tank cap open  
The yellow indicator light turns on.  
1. Close the fuel tank cap.  
Engine coolant temperature gauge  
Digital coolant temperature gauge  
Fig. 13 Coolant temperature gauge in the Volkswagen Digital Cockpit Pro (general example).  
Cold range. The engine is not at operating temperature yet. Avoid high engine RPMs and heavy engine load when the engine is not at operating temperature.  
Normal range.  
Warning range. The needle may move into the warning range when engine load is heavy, especially when outside temperatures are high.  
If the  
warning light flashes, the coolant temperature is too high or the coolant level is too low ⇒ Troubleshooting.  
Driving data menu  
The driving data menu shows driving and consumption data. Depending on the vehicle equipment, various driving data can be displayed. The displayed driving  
data is dependent on the current driving style, the vehicle status, e.g. particle filter regeneration, and the current driving situation, e.g. city traffic. The driving data is  
determined as an average value over sections of different distances and the currently displayed value may therefore differ from the actual average value.  
Switching between the displays  
Vehicles with multi-function steering wheel:  
23  
1. Press the  
or  
button on the multi-function steering wheel.  
Switching memories  
Vehicles with multi-function steering wheel:  
1. Press the  
button on the multi-function steering wheel.  
Since start memory  
If the trip is interrupted for more than two hours, the memory is erased.  
Since refuel memory  
Display and memory of the collective driving and consumption data. The memory is erased when the vehicle is refueled.  
Extended period memory  
The memory collects the driving data up to 19 hours and 59 minutes or 99 hours and 59 minutes driving time or 1999.9 km (miles) or 9999.9 km (miles) distance  
driven. If one of these maximum thresholds is met, the memory is erased. The maximum thresholds may vary depending on the version of the instrument cluster.  
Erasing the driving data memory  
Vehicles with multi-function steering wheel:  
1. Select the memory to be erased.  
2. Press the  
button on the multi-function steering wheel.  
Setting a speed warning  
Vehicles with multi-function steering wheel:  
1. Select the Warning at --- km/h or Warning at --- mph display.  
2. Press the  
button on the multi-function steering wheel to save the current speed and to activate the warning.  
3. Set the speed on the multi-function steering wheel within approximately five seconds by pressing the  
or wait several seconds.  
and  
arrow buttons. Then press the  
button  
The speed will then be saved and the warning will be activated.  
4. Press the  
button again to deactivate.  
The stored speed is erased.  
The warning can be set for speeds between 18 mph (30 km/h) and 155 mph (250 km/h).  
Depending on the country, a single warning tone sounds at speeds of over approximately 80 km/h (approximately 50 mph), and from approximately 120 km/h  
(approximately 75 mph), a continuous warning tone sounds. The  
by law and cannot be altered.  
indicator light will also be displayed in the instrument cluster display. This warning is required  
Driving Data in the Infotainment system  
Driving Data can be displayed in the Infotainment system, in addition to being displayed in the instrument cluster.  
Selecting Displays  
You can select the driving data you would like to display using the vehicle settings in the Infotainment system ⇒ Vehicle settings menu.  
Consumption  
The average fuel consumption is displayed after approximately 300 m (984 ft).  
Range  
This indicates the approximate distance in km (miles) the vehicle can travel under the same driving conditions.  
Speed  
The average speed is displayed after approximately 100 m (approximately 328 ft).  
WARNING  
If the driver is distracted while driving, accidents and serious injuries can occur.  
Never operate the instrument cluster while driving.  
Only adjust any settings in the instrument cluster or Infotainment system when the vehicle is stationary.  
Service  
Service menu  
Depending on the equipment, settings can be applied in the service menu.  
Opening the Service Menu  
1. Select the Range information profile in the instrument cluster.  
24  
2. Press and hold the  
button on the multifunction steering wheel for approximately four seconds.  
3. Navigate in the menu using the buttons on the multi-function steering wheel.  
Resetting the service interval display  
1. Select Service menu.  
2. Follow the instructions in the instrument cluster display.  
Resetting the oil change service  
1. Select Reset oil change service menu.  
2. Follow the instructions in the instrument cluster display.  
Resetting the trip odometer  
1. Select Reset trip menu.  
2. Follow the instructions in the instrument cluster display.  
Displaying the engine code  
1. Select Engine code menu.  
The engine code is shown on the instrument cluster display.  
Setting the time  
1. Select Time menu.  
2. Set the time with the  
and  
arrow buttons.  
Displaying copyright information  
1. Select the Copyright menu to access the copyright information.  
Service interval display  
Displays about service events appear in the instrument cluster display and in the Infotainment system. There are different versions of the instrument cluster and  
Infotainment system; therefore, the appearances of the displays may vary.  
Service appointments at Volkswagen are divided into oil change services and inspections. The service interval display informs the driver about the next service  
appointment which includes an engine oil change and about the next inspection.  
The service intervals are specified for vehicles with the fixed oil change service interval.  
Intervals are determined individually on vehicles with the flexible oil change service interval. Oil change services only need to be performed if the vehicle requires it  
The specific operating conditions and the personal driving style are also taken into consideration. The service early warning message is first displayed 30 days prio  
to the calculated oil change service due date. The displayed remaining distance to be traveled is always rounded to 100 km (miles) and the remaining time is  
rounded to whole days.  
Service notification  
If an oil change service or an inspection service is due in the near future, a service notification will be displayed when the ignition is switched on.  
The specified mileage or time is the distance or time until the next service can be completed.  
Service event  
When an oil change service or an inspection service is due, a chime will sound when switching on the ignition and you can then see a wrench symbol  
seconds in the instrument cluster display together with one of the following displays:  
for a fe  
Inspection now!  
Oil change now!  
Oil change service and inspection now!  
Checking a service due date in the Infotainment system  
When the ignition is on, the engine is off, and the vehicle is stationary, the current service due date can be viewed at any time:  
1. Depending on the vehicle equipment, press the  
button or function key and select the Vehicle menu in the Infotainment system.  
button or function key.  
Or: depending on the vehicle equipment, press the  
2. Depending on how your vehicle is equipped, select the Settings menu.  
3. Select the Service menu item to display the service information.  
Checking a Service Due Date in the Volkswagen Digital Cockpit Pro  
When the ignition is on, the engine is off, and the vehicle is stationary, the current service due date can be viewed at any time:  
1. Open the service menu ⇒ Service menu.  
25  
Resetting the service interval display  
If the service interval display was not reset after the oil change service or inspection service, the display can be reset as follows:  
Vehicles with a digital instrument cluster: The service interval display can only be reset through the service menu ⇒ Service menu.  
Do not reset the service interval display between service intervals or incorrect information will be displayed.  
If the oil change service interval was manually reset, the service interval display then also switches to a fixed service interval, even on vehicles with the flexible oil  
change service interval.  
The service message disappears automatically after a few seconds when the engine is running or when the  
is pressed.  
button on the multi-function steering wheel  
If the 12 V vehicle battery in a vehicle with the flexible service interval has been disconnected for an extended period, the time for the next oil change service  
cannot be calculated. Therefore, the service interval displays may show incorrect calculations. If this is the case, follow the maximum permissible maintenance  
intervals.  
Time  
Setting the time in the Infotainment system  
1. Depending on the design, press the  
button or function key and open the Vehicle menu.  
button or function key.  
Or: depending on the vehicle equipment, press the  
2. Depending on how your vehicle is equipped, open the Settings menu.  
3. Select the Time and date menu item to set the time.  
Setting the Time in the Volkswagen Digital Cockpit Pro  
1. Select the Range information profile.  
2. Press and hold the  
button on the multi-function steering wheel until the service menu is available in the instrument cluster display ⇒ Service menu.  
3. Select Time menu.  
4. Set the correct time using the  
or  
arrow buttons.  
Sport displays  
Lap timer in the instrument cluster  
The lap timer offers the option to  
measure and save the individual lap  
times on a race course manually in the  
vehicle as well as compare these times  
to the best times previously recorded.  
Depending on the equipment, the lap timer can be displayed in the instrument cluster.  
The following main menus can be displayed:  
Lap timer.  
Lap (with current lap specification).  
Statistics.  
Switching between menus  
1. Press the  
or  
button on the multi-function steering wheel.  
For example, the following list will show the layout of the menus in the instrument cluster display. The actual scope of the menus and the names of individual menu  
items depend on the instrument cluster version and the vehicle electronics.  
Menu displays and functions  
Lap timer menu:  
Start  
The time measurement of a lap is started.  
Since start The time measurement begins when the vehicle begins to drive. If it is already moving, the time measurement starts when the vehicle comes to a  
stop in the meantime.  
Statistics An overview of the laps previously recorded is displayed.  
Lap menu:  
Stop  
The active time measurement is paused. The lap is not finished.  
Resume The paused time measurement is resumed.  
Split time A split time is displayed for approximately five seconds. The active time measurement continues to run simultaneously.  
26  
New lap The time of the current lap is stopped and a new lap is started. The time for the finished lap is transferred to the statistics.  
Cancel lap The time measurement is stopped and discarded. The current lap will not be recorded in the statistics.  
End  
The time measurement is finished. The lap will be recorded in the statistics.  
Statistics menu:  
Back  
The display switches back to the previous menu.  
All saved statistics data is reset.  
Reset  
The previously driven lap times are displayed in the Statistics menu. If the maximum lap number of 99 laps or the maximum total duration of 99 hours, 59 minutes  
and 59 seconds is reached, a new time measurement can be started before the statistics are reset.  
WARNING  
Driver distraction can cause accidents and injuries.  
Only adjust lap timer presets and open the statistics when the vehicle is stationary.  
Only operate the lap timer while driving if the driving situation is easy to control and monitor.  
Infotainment system lap timer  
Fig. 14 On the Infotainment system screen: lap timer with stopwatch, function key, and lap times.  
27  
Fig. 15 Function key on the Infotainment system screen: time measurement when the lap is  
stopped,  
running, and  
finished.  
Stopwatch  
Function key with current lap time  
Saved lap times  
Start or resume time measurement; this is only possible when the ignition is switched on. Tap Start to begin the time measurement. The time measurement  
starts automatically once the vehicle moves forward. If the data has been reset in the statistics, a new first round can be started.  
Cancel the current lap. The lap time is deleted. --: --:--.-- is displayed in the statistics.  
End the time measurement.  
Stop the time measurement or cancel the current lap when the time measurement is running.  
Start new lap. The last lap time is saved and a new lap time starts. The total time of the laps is displayed in the statistics.  
Display the split time. The stopwatch stops for several seconds and the split time is displayed.  
Display the statistics after ending or canceling the time measurement: number of laps, total time, fastest and slowest lap, average lap time of all laps, all lap  
times). Tap Reset to reset the statistics.  
A maximum of 99 laps and a maximum duration of 99 hours, 59 minutes and 59 seconds can be recorded. If one of these limits is reached, data in the statistics  
must be deleted before starting another time measurement.  
Opening the lap timer  
1. Depending on vehicle equipment, press the  
button or function key.  
Or: press the  
Or: tap the  
button or function key.  
function key.  
2. Tap the Vehicle function key.  
Or: tap Auto function key.  
3. Tap the Selection function key.  
4. Tap the Sport function key.  
The performance monitor will be displayed.  
5. Tap one of the arrow buttons in the performance monitor to switch to the lap timer.  
You can switch between the lap timer and performance monitor using the arrow buttons.  
Measuring lap times  
The stopwatch measures the lap time in two areas:  
28  
The red needle and the number in the center indicate the running time in seconds, and the smaller display in the inner area shows minutes and hours.  
The display on the right side shows the current lap time with an accuracy of 1/100 of a second. If no laps with split times have been saved yet in the lap timer, then  
there is no difference between the stopwatch and the lap time.  
WARNING  
Driver distraction can cause accidents and injuries.  
Only adjust lap timer presets and open the statistics when the vehicle is stationary.  
Only operate the lap timer while driving if the driving situation is easy to control and monitor.  
Performance monitor  
Fig. 16 On the Infotainment system screen: performance monitor.  
Displays  
Arrow buttons to switch to the lap timer  
The performance monitor is a display  
for sporty driving. The digital  
instruments show values in real time for  
engine power, temperature, and  
acceleration that are determined by  
sensors in the vehicle. This gives the  
driver an overview of the driving  
dynamics.  
Opening the performance monitor  
1. Depending on the version, press the  
2. Tap the Vehicle function key.  
3. Tap the Selection function key.  
4. Tap the Sport function key.  
button or function key in the Infotainment system.  
If you want to switch between the performance monitor and the lap timer, tap one of the left or right arrow buttons above the instruments fig. 16  
.
Selecting instruments and adjusting units  
The display can show a maximum of three instruments at the same time. Every instrument can be selected for any display area fig. 16  
1. To switch between instruments, swipe up over the display.  
(left, center, right).  
The instrument that is currently selected will disappear and a new instrument will appear.  
The units on some instruments can be adjusted in the Infotainment system ⇒ Vehicle settings menu.  
The following instruments can be displayed:  
Boost pressure indicator: the boost pressure indicator fig. 16  
(left) displays the boost pressure between the turbocharger and the engine in bar. The  
farther to the right that the needle on the scale is, the more engine power is being used.  
Accelerometer (g-meter): the accelerometer (g-meter) fig. 16  
(center) displays the acceleration value in the center area in g. The red marking in the tab  
area shows the intensity of the acceleration and the direction of the force. The force in effect is contrary to the physical laws. For example, if you drive to the  
left, the red marking will move in the right area of the instrument and vice versa. When accelerating, the red marking will move downward. When braking, the  
red marking will move upward. The intensity of acceleration is indicated by the position of the red marking from the inside to the outside. If you accelerate  
faster, the red marking will disappear from the center area.  
29  
Power gauge: the power gauge fig. 16  
(right) shows the engine power that is being currently used as a digital value displayed on the surrounding scale in  
kW.  
Engine coolant temperature gauge: when engine load is heavy and outside temperatures are high, the gauge may move farther to the right. This is not a  
cause for concern as long as the indicator light in the instrument cluster display is off or blinking ⇒ Checking and filling engine coolant .  
Oil temperature gauge: the needle stays in the center area under normal driving conditions. If the pointer is in the left, lower area, the engine operating  
temperature has not yet been reached. If the engine operating temperature has not been reached yet, avoid excessive high speeds and acceleration. Engine  
coolant temperature gauge: when engine load is heavy and outside temperatures are high, the gauge may move farther to the right. This is not a cause for  
concern as long as the  
indicator light in the instrument cluster display is off or blinking ⇒ Troubleshooting.  
Adjusting the display areas to the driving situation  
You can select the three instruments that best fit your individual driving style and the driving situation.  
WARNING  
Driver distraction can cause accidents and injuries. Operating the Infotainment system can distract you from traffic.  
Always drive attentively and responsibly.  
NOTICE  
Avoid high engine speeds, full acceleration, and heavy engine loads after starting the engine when it is cold.  
Because of the methods that are used to determine power in the vehicle, the displayed values may not be completely precise.  
Vehicle settings menu  
You can switch individual functions and  
systems on and off and adjust settings  
in the vehicle settings menu in the  
Infotainment system.  
Opening the Vehicle settings Menu  
1. Switch the ignition on.  
2. If necessary, switch on the Infotainment system.  
3. Depending on the equipment, press the  
button or function key and select the Vehicle menu.  
button or function key and select the Settings menu.  
Or: depending on the design, press the  
Or: Tap the  
function key and select the Car menu.  
4. To open other menus in the Vehicle settings menu or to adjust settings to the menu items, tap the  
function key and select the relevant function keys.  
5. Tap the  
function key to return to the previous menu.  
A check mark  
indicates that the respective function is switched on.  
System settings and vehicle information display  
Vehicle settings (setup)  
Depending on the vehicle equipment: Think Blue. Trainer.  
Depending on vehicle equipment: Performance monitor ⇒ Performance monitor.  
Depending on vehicle equipment: Lap timer ⇒ Infotainment system lap timer.  
Volkswagen Digital Cockpit (Pro) ⇒ Volkswagen Digital Cockpit Pro, ⇒ Volkswagen Digital Cockpit Pro Information Displays .  
Active media.  
Driving Data.  
Vehicle status.  
Radio station selection.  
After starting the engine when the 12 V vehicle battery is severely drained or has been replaced or jump-started, system settings, e.g. personal convenience  
settings and programming, may be adjusted or deleted. Check and correct the settings after the 12 V vehicle battery is sufficiently recharged.  
WARNING  
Driver distraction can cause accidents and injuries. Operating the Infotainment system can distract you from traffic.  
Always drive attentively and responsibly.  
30  
Dynamic Road Sign Display  
Introduction  
The Dynamic Road Sign Display detects  
standard road signs using a camera in  
the interior rearview mirror base and  
informs the driver of detected speed  
limits and passing restrictions. Within  
the system limits, the system also  
displays an additional sign to indicate  
special restrictions. The system may  
also continue to display the valid speed  
limit on roads without signs.  
The traffic signs recorded by the Dynamic Road Sign Display are shown in the display of the Volkswagen Digital Cockpit. Depending on the Infotainment system  
installed in the vehicle, the road signs may also be displayed there.  
Dynamic Road Sign Display is always active when the ignition is started.  
Road sign display  
Fig. 17 In the instrument cluster display: Example of detected speed limits.  
After checking and evaluating the information from the camera, the Infotainment system, and the current vehicle data, the Dynamic Road Sign Display function  
displays up to two valid traffic signs and a generic additional sign fig. 17:  
1st position: The traffic sign that currently applies is shown on the left side of the display, for example a speed limit of 20 mph (35 km/h).  
2nd position: Another road sign can be displayed in the second position, such as a passing restriction.  
Additional signs: A recognized additional sign is displayed above the applicable traffic sign. Depending on the system, a generic additional sign is displayed  
instead of the actually recognized additional sign. The applicable traffic sign in the display of the instrument cluster is supplemented by the generic  
additional sign.  
WARNING  
The intelligent technology of the Dynamic Road Sign Display cannot overcome the natural laws of physics, and it can only operate within the limits of the  
system. Do not allow the increased convenience provided by the Dynamic Road Sign Display to tempt you into taking risks. The system cannot replace the  
driver's attention.  
Always adapt your speed and driving style to the visibility, weather, road and traffic conditions.  
Poor visibility, darkness, snowfall, rain, and fog may prevent road signs from being display or may cause them to be displayed incorrectly by the system.  
If the camera lens is dirty, obstructed, or damaged, the Dynamic Road Sign Display function may be limited.  
WARNING  
Driving recommendations and road signs displayed in the Dynamic Road Sign Display may differ from the actual traffic situation.  
Not all road signs can be detected and displayed correctly by the system.  
Traffic signs on the roads and traffic regulations must always take precedence over driving recommendations and displays from the Dynamic Road Sign  
Display function.  
Limits of the Dynamic Road Sign Display  
Please read the introductory information and heed the Warnings and Notice ⇒  
Introduction.  
Error messages  
No road signs available. The system is in the initialization phase.  
Or: the vehicle has not detected any road signs.  
31  
Error: Dynamic Road Sign Display. System malfunction. If the malfunction persists, contact a suitably qualified professional. Volkswagen recommends  
contacting an authorized Volkswagen dealer or authorized Volkswagen Service Facility.  
Speed Alert currently not available. The speed alert from the Dynamic Road Sign Display is malfunctioning. If the malfunction persists, contact a suitably  
qualified professional. Volkswagen recommends contacting an authorized Volkswagen dealer or authorized Volkswagen Service Facility.  
Dynamic Road Sign Display: Clean windshield! The windshield is dirty in the area around the camera or weather conditions are interfering with the camera  
view. Clean the windshield.  
Dynamic Road Sign Display is currently limited. Data is not being transmitted by the Infotainment system. Check that valid map data is loaded in the  
Infotainment system.  
Or: the vehicle is located in an area that is not detected on the map stored in the Infotainment system.  
No data available. The Dynamic Road Sign Display function is not supported in the country where the vehicle is currently being operated.  
Functional limitations  
The Dynamic Road Sign Display is subject to system limitations. The following conditions may cause the Dynamic Road Sign Display function to be limited or to no  
operate at all:  
High ambient temperature or long exposure to direct sunlight.  
Poor visibility, such as in snow.  
Glare, for example from oncoming traffic or the sun  
High speeds  
If the camera is obstructed or dirty  
If road signs are outside of the camera’s visual field  
If road signs are partially or completely covered, for example by trees, snow, dirt, or other vehicles.  
If road signs are not in the standard format  
If there are damaged or bent road signs  
If there are variable traffic signs on overhead signs (variable display of road signs by LEDs s or other lighting).  
If there is outdated map material in the Infotainment system  
If there are stickers on vehicles that indicate road signs, such speed limits on commercial vehicles  
Operating the Dynamic Road Sign Display  
Please read the introductory information and heed the Warnings and Notice ⇒  
Introduction.  
Speed warning  
If the Dynamic Road Sign Display function detects that a valid speed limit is being exceeded, it may warn the driver audibly, or visually and audibly, with a message  
in the instrument cluster display.  
The speed warning can be set or completely deactivated in the Infotainment system ⇒ Vehicle settings menu. The speed warning can be set to a value of 0 mph  
(0 km/h), 3 mph (5 km/h) or 5 mph (10 km/h) over the permitted speed.  
Trailer mode  
On vehicles with a trailer hitch installed at the factory and a trailer that is connected to the vehicle electrical system, the display of road signs relevant to a trailer,  
such as the valid speed limit and passing restrictions for vehicles with a trailer, can be activated and deactivated in the vehicle settings in the Infotainment system  
⇒ Vehicle settings menu.  
For trailer mode, the display of valid speed limits can be adjusted to the model of the trailer and to the legal regulations. The setting can be set in increments of  
10 km/h (5 mph) within a range of approx. 60 km/h (35 mph) and approx. 130 km/h (80 mph). If a speed is set that is higher than the permitted speed for driving wit  
a trailer in the country or state where the vehicle is being operated, the Dynamic Road Sign Display function will automatically display the legal speed limit, for  
example approx. 80 km/h (50 mph) in California.  
32  

Related Topics

Symbols in the instrument cluster Introduction to the instrument cluster Volkswagen Digital Cockpit Pro Volkswagen Digital Cockpit Pro Information Displays Tachometer Fuel gauge Engine coolant temperature gauge Driving data menu Service Time Sport displays Performance monitor Vehicle settings menu Dynamic Road Sign Display

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot