Get Instrument cluster -> Information displays on the digital instrument cluster Pro Guide for Volkswagen Tayron SUV First Generation (2018-2025)

Changing the main display

You can change the focus of the main display manually.

1. Press the arrow buttons

and

on the multifunction steering wheel (→ Digital instrument cluster (Pro)).

Navigation

Navigation map and information for route guidance.

Driver assist systems

Display of active driver assist systems.

Driving data

Display of current driving time, current distance covered, average speed and average and current consumption.

A display with information on the vehicle status, e.g. total mileage, is shown before starting and after switching off the engine.

Selecting secondary displays

1. Select the right or left secondary display area with the

2. Select the desired secondary display with the arrow buttons

3. Confirm the selection with the button.

button.

and

Showing or hiding secondary displays

1. Press and hold the

button.

Configuring secondary displays

You can configure the secondary displays according to your preferences in order to select which secondary displays are available in the

secondary display area:

1. Select the right or left secondary display area with the

2. Use the arrow buttons and to navigate to the Settings menu and open this menu.

3. Press the button to make the changes.

A tick indicates that the corresponding secondary display is activated.

4. To return to menu selection, press the or button.

button.

The secondary displays can be configured or hidden independently of each other.

Navigation map on the digital instrument cluster Pro

Depending on the vehicle equipment, the digital instrument cluster Pro is able to display a detailed navigation map.

The size of the navigation map can be adjusted continuously. To select the preferred map size:

1. To open the Navigation display area, press the arrow buttons

2. To zoom in and out, press the button and use the arrow buttons

3. Press and hold the button on the multifunction steering wheel to show and hide the secondary displays.

and

on the multifunction steering wheel.

or to adjust the desired map size.

If warnings about malfunctions are displayed when the ignition is switched on, it may not be possible to adjust some settings

as described, or the information display may appear different. If the fault persists, go to a suitably qualified workshop.

Volkswagen recommends using an authorised Volkswagen repairer.

WARNING

Operating the instrument cluster and Infotainment system can distract you from the road. If the driver is distracted when driving, this

can cause accidents and serious or fatal injuries.

● Drive with your full attention and with responsibility.

● Never operate the instrument cluster while the vehicle is in motion.

● Adjust all settings in the instrument cluster and Infotainment system only when the vehicle is stationary.

Possible displays in the main display area of the digital instrument cluster Pro

Depending on equipment, various information can be displayed in the main display area (→ Digital instrument cluster (Pro)):

—Outside temperature display.

—Road signs detected by the Dynamic Road Sign Display system.

—Driver assist systems .

—Gear-change indicator (→ Gear-change indicator).

—Open doors, bonnet and boot lid.

—Speed warning for winter tyres.

—Infotainment system and navigation information.

—Radiator fan run-on.

—Engine code.

—Personalisation: Welcome.

—Range (→ Digital fuel gauge).

—Service interval display.

—Position of driving mode selector for automatic gearbox.

—Time.

—Warning and information messages.

—Warning and indicator lamps.

Outside temperature display

If the outside temperature falls below approximately +4°C (around +39°F), the temperature display also shows a snowflake symbol

This symbol remains lit until the outside temperature rises above +6°C (+43°F) .

In the following situation, the temperature displayed may be higher than the actual outside temperature as a result of the heat

radiated from the engine.

—When the vehicle is stationary.

—When the auxiliary heater is being used.

—When travelling at very low speeds.

The measuring range is between -50°C (around -58°F) and +75°C (around +167°F).

WARNING

Roads may be icy at low outside temperatures, also above freezing. There is an increased risk of accidents on icy roads. This can result

in serious or fatal injuries.

● Drive with particular care if the symbol is displayed on the instrument cluster display.

● Always adapt your speed and driving style to the current visibility, weather and road or traffic conditions.

● Never rely only on the outside temperature display.

Gear-change indicator

While the vehicle is in motion, the digital instrument cluster may show which gear should be selected to reduce fuel consumption

(→ Gear-change indicator).

Open doors, bonnet and boot lid

The digital instrument cluster Pro indicates if any doors, the bonnet or boot lid are open once the vehicle has been unlocked and while

the vehicle is in motion. In some cases, an acoustic warning is also given.

Speed warning for winter tyres

A display in the digital instrument cluster Pro indicates when you have exceeded the set maximum speed.

Speed warning settings can be made in the vehicle settings in the Infotainment system (→ Vehicle settings menu).

Radiator fan run-on

This display appears after the engine has been switched off if the radiator fan is in after-run mode.

An after-run time of the radiator fan may be caused by the following:

—Exhaust gas treatment, e.g. during particulate filter regeneration.

—Active brake cooling after driving down hills.

—Dissipation of engine heat after vehicle operation under high loads, e.g. trailer towing.

Engine code

1. Open the Service menu (→ Service menu).

2. Select the Engine code menu option.

Position of driving mode selector for automatic gearbox

The selected position and, depending on driving profile, the selected gear are displayed both on the driving mode selector and in the

digital instrument cluster Pro. The gear shift pattern is displayed in the instrument cluster Pro upon operation of the brake or driving

mode selector (→ Automatic gearbox).

Possible secondary displays in the digital instrument cluster Pro

Depending on equipment, a configuration menu allows additional views to be configured and displayed in the secondary display area

of the digital instrument cluster Pro (→ Digital instrument cluster (Pro)):

—Operating temperatures.

—Driving data displays, e.g. Driving time/Distance covered.

—Compass display.

—Charge pressure.

—Power.

—Torque distribution.

—Navigation information.

—Telephone information.

—Destination information.

Operating temperatures

The following operating temperatures may be displayed, depending on the vehicle equipment:

—Engine oil.

—Coolant.

—Gearbox.

Compass display

If the Compass secondary display is activated, the current compass direction in which you are driving is shown as a blue arrow with a

representation of the vehicle in combination with a compass.

Torque distribution

The secondary display Torque distribution shows the currently present torque individually for each wheel.

Navigation information

When route guidance is active, the Navigation information secondary displays shows an arrow to indicate the direction of travel.

The submenu contains the home address and a list of recent destinations. You can start route guidance using the

button .

Telephone information

If the Telephone secondary display is activated and a mobile telephone is connected via Bluetooth®, for example, the Bluetooth symbol

is shown on the display of the digital instrument cluster Pro. In addition, the symbol shows the charge level of the mobile phone

battery.

A list of recent calls is displayed in the submenu. The list can be used to call the contacts shown.

Destination information

When route guidance is active, the Destination information secondary display shows the expected journey time and the distance to

the destination in km or miles.

Some settings can be saved in the user accounts of the personalisation function and can therefore change automatically when

the user account is changed .

Some notifications in the digital instrument cluster may be overridden by sudden events, e.g. incoming telephone calls.

Depending on the vehicle equipment level, some settings and displays may also appear in the Infotainment system.

The start of the red zone on the rev counter indicates the maximum engine speed that may be used in all positions when the engine is

warm and after it has been run in properly.

You should change up a position, set the driving mode selector to D/S position or lift your foot off the accelerator before the needle

reaches the red zone.

NOTICE

The needle on the rev counter should only briefly point into the red area, as engine damage may otherwise be incurred. Heavy loads

on the engine, particularly when the engine is cold, can cause engine damage.

● When the engine is cold, avoid high engine speeds, strong acceleration and high engine loads.

Changing up a gear early will help to save fuel and reduce engine noise.

Instrument cluster -> Information displays on the digital instrument cluster Pro for Your Volkswagen Tayron SUV First Generation (2018-2025)

Related Topics

Instrument cluster

Popular Owner Manuals

Latest Owner Manuals