Get Controls -> Lights and vision Guide for Audi S5 4 Door Fourth Generation (2017-2024)

document_0900452a81793dcc.book Seite 54 Mittwoch, 21. März 2007 5:42 17

54

Lights and vision

Automatic headlight control (AUTO)*

Lights

When the switch is set to AUTO, the headlights switch on automati-

cally according to the ambient light conditions, for instance in a

tunnel, at sunset, or in the rain or snow. The  symbol lights up

when the dipped headlights are on. The headlights are switched on,

regardless of the light conditions, when you switch on the fog

lights.

Switching lights on and off 

The headlights are switched off automatically when you switch off

the ignition.

On vehicles with a rain sensor, the headlights switch on automati-

cally after several windscreen wiper cycles. The instrument lighting

does not switch on, however.

Fig. 50 Dashboard:

Light switch

While using the automatic headlights you can activate the main

beam headlights as normal if this function has been activated in the

MMI. However, if you switch on the main beam headlights while

using the AUTO function and then do not switch back to the dipped

headlights setting, only the dipped headlights will come on the next

time you switch on the AUTO function. To be able to use the main

beam headlights again you must first pull the main beam lever back

to the "off" position and then push it forward to "on".

Switching on automatic headlights* (AUTO)

– Turn the light switch to AUTO ⇒ fig. 50.

Switching on the side lights

– Turn the light switch to position .

Malfunction of light sensor

Switching on dipped headlights

If a malfunction should occur in the light sensor, the instrument

cluster will show the message:

– Turn the light switch to position .

 Automatic headlights/ automatic wipers defective

Switching off the lights

For safety reasons, the dipped beam headlights will then be

switched on permanently when the light switch is set to the AUTO

position. However, you can still switch the lights on and off in the

normal way with the light switch. You should have the light sensor

checked by a qualified workshop as soon as possible.

– Turn the light switch to position O.

The dipped beam headlights will only work with the ignition on.

The symbol  next to the light switch will light up when the side

lights or headlights are on.

document_0900452a81793dcc.book Seite 55 Mittwoch, 21. März 2007 5:42 17

Lights and vision

55

Fog lights

WARNING

The automatic headlights are only intended to assist the driver.

The driver must always ensure that the headlights are used when

required, and may have to switch them on manually when the light

conditions or visibility are poor. For example, the light sensors are

not able to detect fog. Therefore, you should always switch on the

headlights  in these conditions and when driving after dark.

Note

Fig. 51 Switch for

front fog lights

• The light sensor for automatic headlight control is located in the

mounting for the interior mirror. Do not affix any stickers on this

section of the windscreen to avoid malfunctioning of the sensor.

1

– Press button A ⇒ fig. 51 to switch on the front fog lights

• The default sensitivity of the light sensor, which is set at the

factory, can be changed in the MMI menu Auto headlights

⇒ page 56.

.

2

– Press button A to switch on the rear fog lights .

• If the lights are left on after the key has been taken out of the

Front fog lights

ignition lock, a buzzer sounds when the driver's door is opened.

The side lights or headlights must be switched on. The green diode

at the edge of the switch lights up when the front fog lights are

switched on.

• The use of the lighting described here is subject to the relevant

statutory requirements.

• The coming home/leaving home function is active only when the

When the headlights are set to AUTO, the dipped headlights are

switched on automatically when you switch on the front fog lights.

light switch is set to AUTO.

Rear fog lights

The headlights or side lights and the front fog lights must be

switched on.

The yellow diode at the edge of the switch lights up when the rear

fog lights are switched on.

If you are towing a trailer or caravan equipped with a rear fog light

on a vehicle with a factory-fitted towing bracket, only the rear fog

light on the trailer or caravan will light up.

Controls

Safety

Driving tips

General maintenance

Self-help

Technical data

document_0900452a81793dcc.book Seite 56 Mittwoch, 21. März 2007 5:42 17

56

Lights and vision

Automatic headlights*

Caution

When the light switch is set to AUTO ⇒ page 54, you can make the

headlights switch on earlier or later by changing the Auto head-

lights setting.

To avoid dazzling the traffic behind you, the rear fog light should

only be used in accordance with statutory regulations.

Daytime running lights (daylight headlights)*

Exterior lighting settings

This function can be used to switch the daytime running lights on

and off as required. When the function is activated, the daytime

running lights are switched on automatically when the ignition is

switched on.

You can change the settings for these functions on the

sound system or MMI.

Note

The coming home/leaving home function is active only when the

light switch is set to AUTO.

Instrument lighting

The background lighting of the instruments, the centre

console and the display can be adjusted as required.

Fig. 52 MMI display:

Exterior lighting

CAR

– Select: Function selector button

> Exterior lighting.

Coming home

The coming home function lights up the area round the vehicle after

dark when the ignition has been switched off and the driver's door

opened. It switches on the fog lights, rear lights and number plate

lights. This function can be set to operate for a time interval

between 0 (off) and 30 or 60 seconds.

Fig. 53 Instrument

lighting

Leaving home

The leaving home function lights up the area round the vehicle after

dark when the vehicle is unlocked. It switches on the fog lights, rear

lights and number plate lights. The function can be switched on or

off as required.

– Briefly press the knob to release it.

– Turn the button clockwise +” to increase the brightness

of the instrument lighting in dark conditions.

document_0900452a81793dcc.book Seite 57 Mittwoch, 21. März 2007 5:42 17

Lights and vision

57

Applies to vehicles: with adaptive light

– Turn the button anti-clockwise -” to reduce the bright-

ness of the instrument lighting in dark conditions.

adaptive light

This feature provides better illumination when you drive

through a corner.

– Press the knob in again to prevent the setting from being

changed unintentionally.

The instrument lighting (dials and needles), the centre console illu-

mination and the illumination of the displays are regulated by a

light sensor incorporated in the instrument cluster. In bright condi-

tions any changes made to the brightness of the instrument lighting

have no effect.

Note

The instrument lighting (illumination of dials and needles) is

switched on when the ignition is on and the vehicle's lights are off.

The instrument lighting is dimmed automatically as the daylight

starts to fade; it is switched off completely when the light condi-

tions become very poor. This function is intended to remind the

driver to switch on the dipped-beam headlights in good time when

light conditions become poor.

Fig. 54 adaptive light

when driving

The adaptive light gives better illumination of the bend and the side

of the road when driving through a corner ⇒ fig. 54. The adaptive

light is controlled automatically, depending on the speed of the

vehicle and the steering wheel angle.

The headlights are regulated automatically when you drive through

a corner, depending on how far you turn the steering wheel. To

avoid having a dark spot in front of the vehicle the two headlights

are directed at different angles.

Applies to vehicles: with xenon headlight bulbs

Dynamic headlight range control

Headlights with xenon gas-discharge bulbs automatically adapt to

suit the load being carried when the engine is switched on. The

headlights are also automatically adjusted when the vehicle is in

motion (e.g. when accelerating and braking).

Note

The system is active at speeds from approximately 10 km/h to

110 km/h.

Controls

Safety

Driving tips

General maintenance

Self-help

Technical data

document_0900452a81793dcc.book Seite 58 Mittwoch, 21. März 2007 5:42 17

58

Lights and vision

Hazard warning lights 

Turn signal and main beam lever

The hazard warning lights are used to make other road

users aware of your vehicle in hazardous situations.

The turn signal and main beam lever also operates the

parking lights and the headlight flasher.

Fig. 56 Turn signal and

main beam headlight

lever

Fig. 55 Switch for

hazard warning lights

– Press the switch  to switch the hazard warning lights

on or off ⇒ fig. 55.

The turn signal and main beam headlight lever has the

following functions:

All four turn signals flash simultaneously when the hazard warning

lights are switched on. The two turn signal indicator lamps   and

the indicator lamp in the switch  will flash at the same time. The

hazard warning lights also work when the ignition is switched off.

Turn signals  

– Move the lever all the way up to indicate right, or all the

way down to indicate left ⇒ fig. 56.

– Move the lever briefly up or down just as far as the point

of resistance and then release it: the turn signals will

flash three times.

The hazard warning lights come on automatically in the event of an

accident in which an airbag is triggered or in the case of an emer-

gency stop (full brake application).

– Move the lever up or down just as far as the point of

resistance and hold it there: the turn signals flash for as

long as you hold the lever.

Note

You should switch on the hazard warning lights to warn other road

users, for instance:

Main beam headlights 

• When reaching the tail end of a traffic jam

• If your vehicle breaks down or there is an emergency

– Press the lever forward to switch on the main beams.

• If your vehicle is being towed away, or if you are towing another

– Pull the lever back towards you to switch the main beam

headlights off again.

vehicle.

document_0900452a81793dcc.book Seite 59 Mittwoch, 21. März 2007 5:42 17

Lights and vision

59

Headlight flasher 

Interior lights

– Pull the lever towards the steering wheel to operate the

flasher.

Front interior lights

The front interior lighting also incorporates the reading

lights for the driver and passenger.

Parking lights 

– Switch off the ignition.

– Move the lever up or down to turn on the right or left-

hand parking lights respectively.

Notes on these functions

• The turn signals only work when the ignition is switched on. The

corresponding indicator lamp  or  flashes in the instrument

cluster.

• The turn signals are cancelled automatically when the steering

Fig. 57 Headliner:

Front interior lights

wheel is returned to the straight-ahead position.

• The main beam headlights can only be switched on if the dipped

beam headlights are already on. The main beam headlight indicator

lamp  then comes on in the instrument cluster.

• The headlight flasher comes on for as long as you pull the lever –

even if no other lights are switched on. The main beam headlight

indicator lamp  then comes on in the instrument cluster.

• When the parking lights are switched on, the headlight and the

rear light on one side of the car light up with reduced intensity. The

parking lights will only work with the ignition off. A warning buzzer

will sound for as long as the driver's door is open.

Fig. 58 Headliner:

Front reading lights

A

The rocker switch A ⇒ fig. 57 for the interior light has the

Caution

following functions:

Do not use the main beam headlights or the headlight flasher if this

would dazzle oncoming traffic.

Courtesy light position

A

– Move switch A to the centre position.

Controls

Safety

Driving tips

General maintenance

Self-help

Technical data

document_0900452a81793dcc.book Seite 60 Mittwoch, 21. März 2007 5:42 17

60

Lights and vision

The reading lights are switched on and off with the switches .

Interior light switched on

A

– Move switch A to position I.

Clear vision

Interior light switched off

A

– Move switch A to position O.

Sun visors

Front reading lights 

The sun visors can improve visibility and contribute to

safety.

B

– Press one of the switches A ⇒ page 59, fig. 58 to switch

the left or right reading light on and off.

If you switch on the courtesy lighting, the interior lights come on

automatically when the vehicle is unlocked or the doors are opened.

The light also comes on when the key is pulled out of the ignition. It

goes out approximately 30 seconds after the doors are closed. The

interior light is switched off immediately when the vehicle is locked

or when the ignition is switched on.

If a door is left open, the light is switched off after about 10 minutes

to prevent the battery from running flat.

Fig. 60 Passenger's

side: Sun visor

The brightness of the light is automatically adjusted by a dimmer

when it is switched on.

The sun visors for the driver and the front passenger can be pulled

out of their mountings in the centre of the vehicle and turned

1

towards the doors ⇒ fig. 60 A. Once the sun visor has been turned

towards the door you can pull it towards the rear as desired.

Rear interior lights

Reading lights are also provided for rear passengers.

Make-up mirrors

There are covers on the make-up mirrors in the sun visors. The light

for the mirror (located in the headlining) comes on automatically

2

when the mirror cover A is slid open. The light switches itself off

when the cover is closed and when the sun visor is pushed back

up.

Fig. 59 Headliner: Rear

reading lights

document_0900452a81793dcc.book Seite 61 Mittwoch, 21. März 2007 5:42 17

Lights and vision

61

Applies to vehicles: with sun blind

driven forwards at a speed above about 15 km/h. The current setting

is automatically stored and assigned to the remote control key.

Sun blind

If the rear blind was rolled in automatically when reversing and then

the ignition was switched off and on again, the blind will not roll

back out again when you select a forward gear and the speed

exceeds 15 km/h. You will then have to press the button  on the

centre console to extend the blind again.

A sun blind is provided for the rear window.

The sun blind for the rear window switches off automatically when

it reaches the end position. It can be made to move in the other

direction before it reaches its end position by briefly pressing the

switch a second time. If the ignition is turned off while the blind is

still moving, it continues until it reaches the end position before

switching off.

Fig. 61 Switch for sun

blind (vehicles with

MMI)

Note

• An overload cut-out may be activated if the sun blind is operated

repeatedly. There will then be a short delay before the blind can be

operated again.

• As the material of the sun blind is less flexible at low tempera-

tures the electric actuator is switched off when the temperature in

the car is below -5°C. The blind can only be operated when the

temperature in the car's interior rises above this level.

Fig. 62 Switch for sun

blind

Sun blind (rear window)

– Press the switch  to extend or retract the electric sun

blind for the rear window ⇒ fig. 61 or ⇒ fig. 62.

If you have selected the Automatic rear blind function on in the MMI

the raised sun blind will be retracted automatically when reverse

gear is engaged ⇒ page 51. In this way, the rear blind will not

obstruct your vision when reversing. The rear blind returns to its

raised position when reverse gear is disengaged and the vehicle is

Controls

Safety

Driving tips

General maintenance

Self-help

Technical data

document_0900452a81793dcc.book Seite 62 Mittwoch, 21. März 2007 5:42 17

62

Lights and vision

Automatic wash and wipe

Windscreen wipers

5

– Pull the lever to position A.

Windscreen wipers 

– Release the lever again. The washer will stop and the

wipers will keep running for approximately 4 seconds.

The number of wipe cycles varies according to the length

of time the lever is pulled.

The windscreen wiper lever controls the windscreen

wipers and the automatic wash and wipe.

Switching off the wipers

0

– Move the lever to the "off" position A.

General notes

The washers and wipers will only work when the ignition is switched

on.

Fig. 63 Windscreen

wiper lever

If you stop briefly, e.g. at traffic lights, the wiper speed will automat-

ically be reduced by one level.

The windscreen washer jets are heated when the ignition is

switched on if the outside temperature is low.

The windscreen wiper lever has the following settings:

Brief wipe

Dribble wipe

About 5 seconds after the wash and wipe cycle has finished, the

windscreen wiper system automatically gives the screen one extra

wipe to remove any dribbles of water.

1

– Move the lever down to position A to give the wind-

screen a brief wipe.

Intermittent wipe  (activating rain sensor)

If you want to deactivate the dribble wipe function while driving,

5

pull the lever to position A again within 10 seconds.

2

– Move the lever up to the stop A.

The dribble wipe function will be re-activated the next time the igni-

tion is switched off and on.

A

– Move the control A to the left or right to set the sensi-

tivity of the rain sensor.

Rain sensor*

Slow wiper speed

The rain sensor will only function in the intermittent wipe position.

The intermittent wipe function is activated automatically when it

starts to rain.

3

– Move the lever up to the stop A.

Fast wiper speed

Before you reach a road speed of 6 km/h you will have to activate the

rain sensor manually by switching it off and back on again.

4

– Move the lever up to the stop A.

document_0900452a81793dcc.book Seite 63 Mittwoch, 21. März 2007 5:42 17

Lights and vision

63

A

To reduce the sensitivity level of the rain sensor move control A

⇒ page 62, fig. 63 to the left. To increase the sensitivity level of the

rain sensor move the control to the right.

Note

• Check that the washer fluid reservoir is full before starting a long

journey. Filling the reservoir ⇒ page 231.

If you have selected a high sensitivity level for the rain sensor the

windscreen wipers will react sooner to any moisture on the wind-

screen. The wiper intervals in the intermittent wipe setting are also

varied automatically according to the road speed (in addition to the

sensitivity setting).

• Worn or dirty wiper blades can cause smearing on the glass

which can also impair the effectiveness of the rain sensor. Please

check the wiper blades regularly.

Applies to vehicles: with headlight washers

Headlight washer system

WARNING

• Poor visibility can cause accidents. Always ensure that the

wiper blades are in good condition ⇒ page 64, “Changing wiper

blades”.

The headlight washer system only operates when the lights

are switched on.

• The rain sensor is only intended to assist the driver. The driver

is still obliged to manually operate the windscreen wipers as

required depending on visibility.

5

– Move the automatic wash and wipe lever to position A

⇒ page 62, fig. 63.

The headlight washer system is always activated the first time you

operate the automatic wash and wipe. Subsequently, it is only acti-

vated about every five wash and wipe cycles. The headlights are

always washed if you hold the lever for longer than about

2 seconds.

• Do not use water-repellent coatings on the windscreen. In bad

visibility conditions such as light rain, low sun or when driving at

night these coatings can cause increased dazzle, which is a

serious safety hazard. Such coatings can also cause the wiper

blades to judder.

The headlight washer jets come out of the bumper automatically

(under water pressure).

Caution

Clean off stubborn dirt (insects, etc.) from the lenses at regular

intervals, for instance when stopping for fuel.

• In icy conditions, always check that the wiper blades are not

frozen to the glass before using the wiper for the first time. If you

switch on the wipers when the wiper blades are frozen to the glass,

this could damage both the wiper blades and the wiper motor.

To ensure that the system works properly in winter, keep the nozzle

holders free of snow and remove any ice with a de-icer spray.

• Make sure you switch off the windscreen wiper system (lever in

position "0") before you use an automatic car wash. This will avoid

inadvertent triggering of the wipers and possible damage to the

wiper system.

Controls

Safety

Driving tips

General maintenance

Self-help

Technical data

document_0900452a81793dcc.book Seite 64 Mittwoch, 21. März 2007 5:42 17

64

Lights and vision

when they are in the service position you will also avoid damaging

the paintwork on the bonnet.

Service position

Use the service position to change the wiper blades.

• off - the windscreen wipers will be moved back to their original

position.

Caution

Never move the vehicle with the front wiper arms in a raised posi-

tion as they are automatically moved back to their normal park posi-

tion above a speed of 6 km/h. The paintwork on the bonnet may be

damaged as a result.

Fig. 64 MMI display:

Windscreen wipers

Note

• You can also use the service position, for example, if you want to

fix a cover over the windscreen in the winter to keep it clear of ice.

• The service position is automatically set to off when you operate

the windscreen wiper lever or the road speed exceeds 6 km/h.

Changing wiper blades

Good wiper blades are essential for clear vision.

Fig. 65 Service posi-

tion

You can set the wipers to the service position on the sound

system or MMI*.

– If the wiper blades are not frozen to the windscreen,

0

move the windscreen wiper lever to the "off" position A

⇒ page 62, fig. 63.

Fig. 66 Removing the

wiper blades

CAR

– Select: Function selector button

wipers > Service position ⇒ fig. 64.

> Windscreen

Taking off the wiper blade

• on - the wiper blades can only be replaced when the wiper arms

are in the service position ⇒ fig. 65. If you only work on the wipers

– Set the wipers to the service position ⇒ page 64.

document_0900452a81793dcc.book Seite 65 Mittwoch, 21. März 2007 5:42 17

Lights and vision

65

– Lift the wiper arm away from the glass.

Anti-dazzle setting

– Pull the lever at the bottom of the mirror towards you.

1

– Press the release button A on the wiper blade

⇒ page 64, fig. 66. Hold the wiper blade firmly and press

2

it forwards slightly A.

Applies to vehicles: with automatic anti-dazzle adjustment for interior mirror

Automatic anti-dazzle adjustment

3

– Slide the wiper blade upwards A.

The automatic anti-dazzle function can be switched on

and off as desired.

Fitting the wiper blade

– Fit the new wiper blade into the mounting on the wiper

4

arm A. You should hear it engage in the wiper arm.

– Fold the wiper arm back down onto the glass.

WARNING

• To prevent smearing on the glass, the wiper blades should be

cleaned regularly using a window cleaner solution. If the wiper

blades are very dirty (insects etc.), they should be cleaned using a

sponge or cloth – bad visibility can cause accidents.

Fig. 67 Anti-dazzle

interior mirror: On/off

button with indicator

lamp

• For safety, the wiper blades should be changed once or twice a

Switching off anti-dazzle function

year.

A

B

– Press button A ⇒ fig. 67 - the indicator lamp A will go

out.

Caution

The windscreen wipers must be in the service position ⇒ page 64

when replacing the blades! Otherwise the wiper motor or the paint-

work on the bonnet may be damaged.

Switching on anti-dazzle function

A

B

– Press button A - the indicator lamp A will light up.

Anti-dazzle function

The anti-dazzle function is activated every time the ignition is

switched on. The green indicator lamp lights up in the mirror

housing.

Rear-view mirrors

Manual anti-dazzle adjustment

When the anti-dazzle function is activated the interior mirror will

darken automatically according to the amount of light it receives

(for example from the headlights of a vehicle behind). The mirror

will not darken automatically:

Normal setting

– Push the lever at the bottom of the mirror away from you.

Controls

Safety

Driving tips

General maintenance

Self-help

Technical data

document_0900452a81793dcc.book Seite 66 Mittwoch, 21. März 2007 5:42 17

66

Lights and vision

• when the interior lighting is switched on

• when reverse gear is engaged

Exterior mirrors

The exterior mirrors are adjusted electrically.

WARNING

Electrolyte fluid can leak from a broken mirror. This fluid can cause

irritation to the skin, eyes, and respiratory organs. Wash thor-

oughly with clean water should you come into contact with this

fluid. Seek medical assistance if needed.

Caution

Fig. 68 Detail of the

armrest: Adjuster knob

Electrolyte fluid leaking from a broken mirror can cause damage to

plastic surfaces. Use a sponge or similar to remove the fluid as soon

as possible.

Adjusting exterior mirrors

L

– Turn the adjuster knob to position A(left exterior mirror)

Note

R

or position A (right exterior mirror) ⇒ fig. 68.

• If you switch off the anti-dazzle function for the interior mirror,

this will also deactivate the anti-dazzle function for the exterior

mirrors.

– Move the knob as required to adjust the exterior mirror

for a good rearward view.

• The automatic anti-dazzle function will only work properly if the

sun blind* for the rear window is not in use and there are no other

objects preventing light from reaching the interior mirror.

Heated mirrors

A

– Turn the knob to position A.

• Do not attach any stickers to the windscreen in front of the

Retracting both exterior mirrors*

sensors, as these could lead to malfunctioning of the mirror.

B

– Turn the knob to position A.

The mirrors are heated depending on the outside temperature until

the ignition is switched off, even if the knob is no longer in position

A

A.

It may be advisable to retract* the exterior mirrors to protect them

when parking or when driving through tight spaces.

document_0900452a81793dcc.book Seite 67 Mittwoch, 21. März 2007 5:42 17

Lights and vision

67

Applies to vehicles: with automatic anti-dazzle adjustment for exterior mirrors

Memory for exterior mirrors*

Automatic anti-dazzle adjustment for exterior

mirrors

On vehicles with memory function for the driver's seat, the setting

of the exterior mirrors is automatically stored together with the seat

position ⇒ page 72.

The exterior mirrors darken together with the automatically

adjusting interior mirror. When the ignition is on, the mirrors will

darken automatically according to the amount of light received (for

example from the headlights of a vehicle behind).

Tilting function for exterior mirror on passenger side*

(only if equipped with memory for exterior mirrors)

When reverse gear is engaged, the mirror surface tilts slightly

downwards, provided the mirror control is switched to the exterior

When the interior lights are switched on, or when reverse gear is

engaged, the mirrors revert to their original (i.e. not darkened)

condition.

R

mirror on the passenger's side (knob in position A ⇒ page 66,

fig. 68). This provides a better view of the kerb when parking.

The mirror returns to its original position when reverse gear is

disengaged and the vehicle is driven forwards at a speed above

about 15 km/h. The mirror will also return to its original position

when the adjuster knob is turned to the position for the driver's

WARNING

Electrolyte fluid can leak from a broken mirror. This fluid can cause

irritation to the skin, eyes, and respiratory organs. Wash thor-

oughly with clean water should you come into contact with this

fluid. Seek medical assistance if needed.

L

exterior mirror A or when the ignition is switched off.

If the position of the mirror surface is changed while the mirror is

tilted, this new position is automatically stored and assigned to the

remote control key when you disengage reverse gear.

Caution

Electrolyte fluid leaking from a broken mirror can cause damage to

the paintwork or plastic surfaces. Use a sponge or similar to remove

the fluid as soon as possible.

• Convex or wide-angle* exterior mirrors give a larger field of

vision. However, they also make objects appear further away than

they actually are. For this reason, you should not rely on these

mirrors for judging the distance of vehicles behind.

Note

• If one of the mirror housings is knocked out of position (e.g.

when parking), the mirrors must first be fully retracted with the elec-

tric control. Do not readjust the mirror housing by hand, as this will

interfere with the mirror adjuster function.

• If you switch off the anti-dazzle function for the interior mirror,

this will also deactivate the anti-dazzle function for the exterior

mirrors.

• The automatic anti-dazzle function will only work properly if the

sun blind* for the rear window is not in use and there are no other

objects preventing light from reaching the interior mirror.

Note

If the electrical adjustment should ever fail to operate, the mirrors

can be adjusted by hand by lightly pressing the edge of the mirror

glass.

Controls

Safety

Driving tips

General maintenance

Self-help

Technical data

document_0900452a81793dcc.book Seite 68 Mittwoch, 21. März 2007 5:42 17

68

Lights and vision

Applies to vehicles: with digital compass

Digital compass

Setting the correct compass calibration zone

Applies to vehicles: with digital compass

The correct compass calibration zone must first be set

before the compass can give an accurate reading.

Activating and deactivating the compass

The compass direction will appear in the mirror.

Fig. 69 Interior mirror:

activated digital

compass

– To switch the compass on and off, press and hold

A

button A until the compass display in the mirror

⇒ fig. 69 appears or disappears.

The digital compass only works when the ignition is on. The points

of the compass are displayed as follows: N (North), NE (North East),

E (East), SE (South East), S (South), SW (South West), W (West), NW

(North West).

Fig. 70 Map of compass calibration zones

A

– Press and hold button A ⇒ fig. 69 until the currently set

zone number is displayed on the interior mirror.

A

– Press button Arepeatedly until the correct zone number

Note

appears. The adjustment mode will be ended automati-

cally after a few seconds.

To avoid inaccurate compass readings, do not hold any remote

controls or other electrical devices or metal objects near the interior

mirror.

document_0900452a81793dcc.book Seite 69 Mittwoch, 21. März 2007 5:42 17

Lights and vision

69

Applies to vehicles: with digital compass

Calibrating compass

The compass must be re-calibrated if the display is incor-

rect or inaccurate.

A

– Press and hold button A until the letter C appears in the

interior mirror.

– Drive in a circle at a speed of about 10 km/h until a point

of the compass is displayed in the interior mirror.

WARNING

Calibrate your compass at a location where there is no traffic so

that you do not endanger yourself or other road users (accident

risk).

Controls

Safety

Driving tips

General maintenance

Self-help

Technical data

Controls -> Lights and vision for Your Audi S5 4 Door Fourth Generation (2017-2024)

Related Topics

Popular Owner Manuals

Latest Owner Manuals