Get Driving -> Speed Limit recognition and recommendation Guide for Citroen Spacetourer Van First Generation (2019-2024)

Driving

After carrying out any work on the system,

Speed Limit recognition

and recommendation

the pressure of the four tyres must be

checked and the system reinitialised.

Memorising speeds

This function allows speeds to be saved, which

can then be offered to set the two systems: the

speed limiter (to limit the speed of the vehicle)

or the cruise control (for a vehicle cruising

speed).

You can memorise up to six speed settings

for each of the two systems. By default, some

speed settings are already memorised.

F Select the system for which you want to

memorise new speed settings.

This system allows the speed limit detected by

the camera to be displayed in the instrument

panel.

The system also processes speed limit

information from the navigation system

mapping.

F Press the button corresponding to the

speed setting you want to modify.

F Enter the new value using the numerical

keypad and confirm.

Memorisation

You should update your navigation

mapping regularly in order to receive

accurate speed limit information from the

system.

As a safety measure, the driver must carry

out these operations when stationary.

This function can be accessed in the Driving

menu of the touch screen.

F Select the "Driving functions" tab then

Adjusting Speeds.

Specific speed limits, such as those for heavy

goods vehicles, are not displayed.

The display of the speed limit in the instrument

panel is updated as you pass a speed limit sign

intended for cars (light vehicles).

144

Driving

The speed limit units (mph or km/h)

depend on the country you are driving in.

This should be taken into account in order

to observe the speed limit.

For the system to operate correctly when

you change country, the units for speed in

the instrument panel must be those for the

country you are driving in.

To maintain correct operation of the

system: regularly clean the area in front of

the camera.

The internal surface of the windscreen can

also become misted around the camera.

In humid and cold weather, demist the

windscreen regularly.

The system is active but is not detecting speed

limit information.

Activation/Deactivation

On detection of speed limit information, the

system displays the value.

Activation and deactivation of the system is

done in the touch screen's Driving menu.

Select the "Vehicle settings" tab, then

"Security"/"Safety" and "Recommended

speed display".

The automatic reading of road signs is

a driving assistance system and does not

always display speed limits correctly.

The speed limit signs present on the road

always take priority over the display by the

system.

The system cannot in any circumstances

replace the need for vigilance on the part

of the driver.

The driver must observe the driving

regulations and must adapt the speed of

the vehicle to suit the weather and traffic.

The system may not display the speed

limit if it does not detect a speed limit sign

within a preset period.

Operating limits

The legislation on speed limits is specific to

each country.

Displays in the instrument panel

The system does not take account of reduced

speed limits in the following cases:

-

poor weather (rain, snow),

atmospheric pollution,

when towing,

driving with a space-saver type spare wheel

or snow chains fitted,

6

-

puncture repair using the temporary repair

kit,

young drivers, etc.

The system is designed to detect signs

that conform to the Vienna Convention on

road signs.

The following situations may interfere with

the operation of the system or prevent it from

working:

1. Detected speed limit indication.

or

-

poor visibility (inadequate street lighting,

falling snow, rain, fog),

2. Indication of the end of the speed limit.

145

Driving

-

windscreen area located in front of the

Steering mounted controls

Memorising the speed

camera dirty, misted, frost-covered, snow-

covered, damaged or covered by a sticker,

fault with the camera,

obsolete or incorrect mapping,

obstructed road signs (by other vehicles,

vegetation, snow),

-

F Switch on the speed limiter/cruise control.

Speed limiter/cruise control information is

displayed.

-

speed limit signs that do not conform to the

standard, are damaged or distorted.

On detection of a sign offering a new speed

limit, the system displays the value and MEM

flashes for a few seconds to offer to make it

a new speed setting.

1. Select speed limiter/cruise control mode.

2. Memorise a speed setting.

Recommendation

Display in the instrument panel

If there is a difference of less than 6 mph

(10 km/h) between the speed setting and

the speed displayed by the Speed Limit

recognition and recommendation, the

MEM symbol is not displayed.

In addition to Speed Limit recognition and

recommendation, the driver can select the

speed displayed as a speed setting for the

speed limiter or cruise control using the speed

limiter or cruise control memorisation button.

Depending on the road conditions, several

speeds may be displayed.

F Make an initial press on button 2 to request

saving of the speed suggested.

A message is displayed to confirm the request.

For more information on the Speed

limiter, Cruise control or Adaptive

cruise control, refer to the corresponding

sections.

3. Speed limit indication.

4. Memorise the speed.

5. Current speed setting.

F Press button 2 again to confirm and save

the new speed setting.

After a predetermined period, the screen

returns to the current display.

146

Driving

Steering mounted controls

Displays in the instrument panel

Speed limiter "LIMIT"

System which prevents the

vehicle from exceeding the speed

programmed by the driver.

Once the programmed speed limit is reached,

additional pressure on the accelerator pedal

has no effect.

1. Select speed limiter mode.

2. Decrease the programmed speed.

3. Increase the programmed speed.

4. Speed limiter On/Pause.

Operation of the speed limiter requires

a programmed speed of at least 19 mph

(30 km/h).

The speed limiter is paused using the control.

The programmed speed can be exceeded

temporarily by pressing the accelerator firmly

beyond the point of resistance.

To return to the programmed speed, simply

release the accelerator pedal until the set

speed limit has been reached again.

6. Speed limiter on/off indicator.

7. Speed limiter mode selected.

8. Value of the speed setting.

5. Display the list of memorised speeds or

Use the speed suggested by the Speed

Limit recognition and recommendation

system.

Switching on/Pause

For more information on Memorising speeds,

refer to the corresponding section.

For more information on Speed Limit

recognition and recommendation and its

memorisation, refer to the corresponding

section.

6

F Turn wheel 1 to the LIMIT position: the

speed limiter mode is selected but is not

switched on (Pause).

F Switch the speed limiter on by pressing

button 4, if the speed displayed is suitable

(by default, the last speed programmed).

F You can pause the speed limiter by pressing

button 4 again: the display confirms that it

has been stopped (Pause).

The programmed speed remains in the system

memory when the ignition is switched off.

The speed limiter cannot, in any circumstances,

replace the need to observe speed limits, nor can it

replace the need for vigilance on the part of the driver.

147

Driving -> Speed Limit recognition and recommendation for Your Citroen Spacetourer Van First Generation (2019-2024)

Related Topics

Driving

Popular Owner Manuals

Latest Owner Manuals