2002-2008 Cupra Born SUV Driving User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Driving for Your Cupra Born SUV First Generation (2002-2008)

Driving  
If the assistant is activated in the infotainment  
system, position D is engaged and the acceler-  
ator pedal is not depressed, the vehicle auto-  
matically recuperates energy. While doing so,  
it adapts to the driving situation and external  
conditions, such as vehicles in front and speed  
restrictions. During recuperation, energy from  
the moving vehicle is used to charge the high-  
voltage battery ››› page 142. This causes the  
vehicle to slow down.  
WARNING  
Driving  
●
Restricting pedal operation can lead to  
critical situations while driving.  
Driving indications  
●
Never lay or ꢀt ꢁoor mats or other ꢁoor  
coverings over the original ꢁoor mats. This  
would reduce the pedal area and could ob-  
struct the pedals. Risk of accident.  
Pedals  
●
Make sure you can always step on the brake  
and accelerator pedals without any problems.  
●
Never place objects in the driver footwell.  
An object could move into the pedal area and  
impair pedal operation.  
●
Ensure that the pedals can return unimpaired  
to their initial positions.  
If the accelerator pedal is not depressed while  
in position B ››› page 146, Gear selector,  
very intense recuperation occurs.  
●
Ensure that the ꢀoor mats are securely fas-  
tened during the trip and do not obstruct the  
Economical driving style.  
pedals ›››  
.
This also increases when the brake pedal is de-  
pressed.  
An appropriate driving style reduces consump-  
tion, environmental pollution and wear and  
tear on the electric drive system, brakes and  
tyres. Some tips that are good for the environ-  
ment and your wallet can be found below.  
Only use ꢀoor mats which leave the pedals  
clear and which are secured to prevent them  
from slipping. You can obtain suitable ꢀoor  
mats from a specialised dealership. Fasteners  
for ꢀoor mats are ꢁtted in the footwells.  
Avoid full throttle  
At excessively high speeds, rolling resistance  
and aerodynamics increase along with the  
force required to move the vehicle. This re-  
duces the vehicle’s range. Never drive at the  
vehicle’s maximum speed.  
Drive with anticipation  
Wear suitable footwear  
An erratic driving style reduces range. Fre-  
quent accelerating and braking can be avoided  
by keeping an eye on the traꢂic. Keeping a suf-  
ꢁcient distance from the vehicle in front helps  
you to drive with anticipation.  
Always wear shoes which support your feet  
properly and give you a good feeling for the  
pedals.  
Perform regular maintenance  
Regular maintenance is essential for economi-  
cal driving and increases the service life of the  
vehicle.  
Take advantage of braking energy recupera-  
tion  
If the eco-eꢂicient driving assistant is deacti-  
vated in the infotainment system, position D  
is engaged and the accelerator pedal is not  
depressed, the car will coast.  
138  
Drivingindications  
●
Use the stationary air conditioning when  
Tyre pressure  
WARNING  
charging the battery with an external power  
Very low tyre pressure not only causes tyre  
wear, but also increases tyre rolling resistance,  
which reduces the vehicle’s range. Use tyres  
with optimised rolling resistance.  
Loads that move around could seriously  
threaten the vehicle's stability and safety,  
extend the braking distance during hard or  
emergency braking and lead to serious acci-  
dents and injuries.  
supply ››› page 136.  
●
Switch oꢂ the convenience consumers when  
they have completed their task.  
Adapt tyre pressure to the load:  
●
Secure the load correctly to prevent it from  
WARNING  
●
Please note the information on the tyre pres-  
moving around.  
Adapt your speed and safe distance to the  
vehicle in front of you at all times to suit  
the visibility, weather, road and traꢂic condi-  
tions.  
sure sticker ››› page 298.  
●
●
Secure heavy objects with suitable lashing  
Tyre pressure loss indicator ››› page 307.  
straps or tie-down belts.  
●
Ensure that the rear seat backrests are se-  
Remove unnecessary weight  
curely engaged.  
Energy consumption can be reduced if the lug-  
gage compartment is emptied of items such  
as snow chains or unused child seats before  
setting oꢂ.  
For the sake of the environment  
NOTICE  
CUPRA dealers can provide you with further  
information about correct vehicle mainte-  
nance and spare parts, e.g. new, particularly  
energy-eꢂicient tyres.  
Do not transport large amounts of liquid in  
the vehicle interior. If the liquid leaks out, it  
could get into the orange high voltage cable  
connectors. This could damage the electrical  
system and the high voltage battery.  
To keep the vehicle’s aerodynamic drag as low  
as possible, remove exterior accessories, such  
as the ski rack, bike rack or roof rack, when  
they are no longer needed.  
Driving with a loaded vehicle  
In order to achieve appropriate driving char-  
acteristics when the vehicle is loaded, please  
note the following:  
Driving with the rear lid open  
Saving energy  
Convenience consumers, such as the air con-  
ditioning or the heated windscreen and win-  
dow, require energy from the high-voltage bat-  
tery. If you wish to increase the vehicle’s range:  
Driving with the rear lid open is particularly  
dangerous. Secure all objects and the open  
rear lid correctly and take any necessary meas-  
ures.  
●
Place all luggage securely ››› page 263.  
●
Accelerate with particular care and precau-  
tion.  
●
Set higher vehicle interior temperatures in  
Driving with the rear lid open increases the  
aerodynamic drag of the vehicle, along with  
the energy consumption of the electric drive  
system. This therefore considerably reduces  
summer and lower temperatures in winter. If  
the outside temperature is high, ventilate the  
vehicle interior before setting oꢂ.  
●
●
●
Avoid sudden braking and manoeuvres.  
Brake earlier than usual.  
If applicable, please note the information  
about the roof rack.  
139  
Driving  
the vehicle's possible range. CUPRA therefore  
recommends that you do not drive with the  
rear lid open.  
Note  
Note  
●
Depending on the country, it may be forbid-  
den to drive with the rear lid open. Please  
observe the legal regulations of the country  
in question.  
Driving through ꢁooded areas may severely  
damage vehicle components such as the  
electric drive system, drive train or electrical  
system.  
WARNING  
Driving with the rear lid unlocked or open  
can cause serious injury.  
●
››A›vpoaidgedr3iv1i3n.g through salt water (corrosion)  
Driving on ꢁooded roads  
●
●
Always drive with the rear lid closed.  
Place all objects securely inside the lug-  
To prevent damage to the vehicle driving on  
ꢀooded roads, take the following into account:  
Trips abroad  
gage compartment. Otherwise, loose objects  
could fall out of the luggage compartment  
and injure road users driving behind.  
●
The vehicle has been manufactured for a spe-  
ciꢁc country and meets the approval regula-  
tions in force in that country at the time it was  
manufactured.  
Water should never come above the lower  
edge of the bodywork.  
●
Always drive carefully and with special care  
●
●
Drive at pedestrian speed.  
and anticipation.  
Never stop the vehicle in the water, drive in  
●
Avoid braking and sudden manoeuvres, as  
If you are going to use the vehicle abroad tem-  
porarily or for a short period of time, please  
observe the relevant instructions.  
reverse or disconnect the drive system.  
the open rear lid could move uncontrollably.  
●
Vehicles driving in the opposite direction  
●
When transporting objects that protrude  
form waves that can raise the water level so  
high that your vehicle will not be able to cross  
the water safely.  
from the luggage compartment, mark them  
accordingly to warn other road users. Please  
bear in mind all legal provisions.  
Some countries have special safety regulations  
and provisions that the vehicle may not comply  
with. Before travelling abroad, CUPRA recom-  
mends that you seek information from one of  
your dealers about the legal provisions in force  
in your destination country.  
●
Never use the rear lid to support or secure  
objects protruding from the luggage com-  
partment.  
WARNING  
After driving through ꢁooded zones, braking  
eꢂectiveness can decrease if the brake discs  
●
If a luggage rack is ꢀtted on the rear lid, re-  
If you are going to sell the vehicle in another  
country or use it there for a longer period of  
time, please observe the legal regulations in  
force in the country in question.  
move it and the load when you have to drive  
with the rear lid open.  
or pads are damp ››› page 151.  
NOTICE  
In some cases it may be necessary to install or  
remove certain equipment at a later date, and  
to deactivate certain functions. Sets and types  
An open rear lid changes the height and, in  
some cases, the length of the vehicle.  
140  
Drivingindications  
of services may also be aꢂected. In particular,  
this can occur if the vehicle is to be used in an-  
other climatic region for a long period of time.  
Brake energy recuperation (charging)  
WARNING  
When braking the vehicle, electric power  
is generated through the electric engine  
and stored in the high-voltage battery  
››› page 142. This also occurs to a lesser  
extent when the vehicle moves by inertia or  
drives downhill in the deceleration phase.  
An electric vehicle emits very little noise  
when it is in operation, both when stationary  
and when driving. This means that other road  
users and pedestrians (including children)  
may not hear or notice it, or only with diꢂi-  
culty. This can lead to accidents and injuries,  
e.g. in residential areas, when manoeuvring  
or reversing.  
Due to the diꢂerent frequency bands around  
the world, the factory-ꢁtted infotainment sys-  
tem may not work in another country.  
Due to diꢂering legal regulations in place,  
charging the high-voltage battery in other  
countries may only be permitted at a reduced  
charging current. The charging cable limits the  
charging current based on the infrastructure  
that is used. If the settings are diꢂerent, it is  
As the high-voltage battery’s state of charge  
increases, recuperation reduces along with the  
engine braking eꢂect. When the high-voltage  
battery is fully charged, no energy recupera-  
tion takes place and the engine braking eꢂect  
WARNING  
Any accidental movement of the vehicle  
could result in serious injury.  
charged at the lowest value ››› page 85.  
is not available ›››  
.
Recovery can be displayed in the Digital Cock-  
pit or on the infotainment system display.  
●
When the drive system is engaged and gear  
NOTICE  
position D/B is selected or reverse gear R is  
engaged, the vehicle should be stopped by  
pressing the brake pedal.  
●
CUPRA cannot be held liable for any dam-  
age to the vehicle due to insuꢂicient work or  
of lack of availability of genuine spare parts.  
Slow travel function  
The slow travel function consists of driving  
slowly, at about 5 km/h (3 mph), forward or  
reverse without pressing the accelerator pedal.  
The slow travel function is activated automati-  
cally:  
●
CUPRA accepts no liability if the vehicle  
WARNING  
does not meet the legal requirements in  
force in other countries and continents, or  
if it only partially meets them.  
As the state of charge of the high-voltage  
battery increases, the engine braking eꢂect  
caused by the recuperation of the brake en-  
ergy is reduced and may even be completely  
cancelled out.  
●
When the drive system is on and the gear  
selector is in the D/B or Rposition.  
Electric drive system functions.  
The slow travel function deactivates if:  
●
Slow down before starting a long distance  
Delivery of power from the electric engine  
with a steep descent.  
●
The gear selector is moved to the N position  
The maximum torque of the electric engine is  
available immediately after pressing the accel-  
erator pedal.  
●
During a long distance with a steep de-  
or the electronic parking brake is engaged.  
scent, reduce the speed with the vehicle  
brake.  
141  
Driving  
●
Position D selected and the eco-eꢂicient  
Brake energy recuperation (charg-  
ing)  
WARNING  
driving assistant deactivated: no recuperation  
takes place.  
As the high-voltage battery's state of charge  
increases, the engine braking eꢂect drops  
and may be completely cancelled out. This  
puts much greater demand on the vehicle’s  
brakes.  
When braking the vehicle and when the vehi-  
cle moves by inertia or travels downhill in the  
deceleration phase, electric power is gener-  
ated by the electric engine and stored in the  
high-voltage battery. The electric motor then  
operates as an alternator and produces a en-  
gine braking eꢂect. This process is called brake  
energy recuperation.  
●
Position D selected and the eco-eꢂicient  
driving assistant activated: automatic recuper-  
ation. The recuperation level is automatically  
selected based on navigation data and the  
traꢂic situation.  
●
When charging the high-voltage battery  
in high-altitude locations (e.g. on top of a  
mountain pass), never fully charge it. In this  
way, when descending the mountain the en-  
gine braking eꢂect through recuperation will  
be enabled.  
●
Position B selected: intense recuperation.  
The vehicle also recovers energy when the  
brake pedal is depressed.  
The engine braking eꢂect can be more or less  
intense, depending on the position of the gear  
●
Slow down before starting a long distance  
with a steep descent.  
Eco-eꢂicient driving assistance  
selector ››› page 146. If the recuperation  
is very intense, the brake light of the vehicle  
may also be switched on. As the high-voltage  
battery’s state of charge increases, recupera-  
tion reduces along with the engine braking  
eꢂect. When the high-voltage battery is fully  
charged, no energy recuperation takes place  
and there is no engine braking eꢂect. When  
the vehicle detects that road conditions do not  
allow safe contact between the wheels and the  
road surface, energy recuperation is automat-  
ically reduced, along with the engine braking  
eꢂect. The power indicator provides informa-  
tion about the availability of recuperation and  
The eco-eꢂicient driving assistant helps the  
driver to make eꢂicient use of the vehicle's en-  
gine braking eꢂect. It selects the recuperation  
level based on navigation data and traꢂic situa-  
tion.  
●
During a long distance with a steep de-  
scent, reduce the speed with the vehicle  
brake.  
Troubleshooting  
The assistant can be switched on and oꢂ in the  
infotainment system’s vehicle settings.  
Now only manoeuvring is possible!  
Charge. Check the manual  
Driving down slopes  
On descents, position B should be selected  
whenever possible.  
The control lamp lights up in red to warn you  
that the system's power is very limited and the  
vehicle may soon stop in the middle of the  
road.  
Never let the vehicle roll downhill with position  
N neutral selected.  
the engine braking eꢂect ››› page 23.  
The vehicle recuperates energy diꢂerently de-  
pending on the selected gear position and the  
infotainment system settings:  
A message is displayed in the Digital Cockpit  
and an audible warning sounds.  
The air conditioning comfort functions are re-  
stricted ››› page 128.  
142  
Connecting and disconnecting the drive system  
This may occur due to the following condi-  
tions:  
Performance restricted. Check the  
manual  
Connecting and discon-  
necting the drive system  
●
Very low state of charge of the high-volt-  
The control lamp lights up yellow to warn you  
that the power has decreased signiꢁcantly and  
may decrease further.  
age battery.  
Switching the ignition on/oꢂ  
–
The control lamp comes on while the  
vehicle is moving. From this moment on-  
wards, the vehicle can be started twice  
››› page 144.  
If traꢂic conditions permit, move the vehicle  
onto the right hand side of the road and park  
it safely, or go to a charging station if possi-  
ble.  
A message is displayed in the Digital Cockpit  
and an audible warning sounds.  
The air conditioning comfort functions are re-  
stricted ››› page 128.  
As soon as the battery power increases again,  
the control lamp turns oꢂ.  
●
Temperature and state of charge of the  
Depending on the state of charge, CUPRA rec-  
ommends:  
high-voltage battery.  
–
The control lamp turns on before the drive  
●
When the state of charge is low, the high-  
system is switched on. Only manoeuvring is  
possible (at a speed of up to 7 km/h [4 mph]).  
voltage battery must be charged.  
Fig. 115 Starter button  
●
With a high state of charge and very high  
CUPRA recommends that you charge the  
high-voltage battery and prepare the car for  
departure ››› page 137.  
Some vehicle functions are activated when the  
driver approaches the vehicle with the corre-  
sponding key.  
or low outside temperatures, the high voltage  
battery heats up or cools down while driving.  
After a certain amount of time, the available  
power increases again.  
Note  
Switching on the ignition  
If you are planning to depart in low out-  
side temperatures, CUPRA recommends  
pre-heating the vehicle while it is parked  
●
●
Press the brake pedal.  
OR: press the ignition/start button once. The  
ignition/start button is located on the right  
hand side of the steering column.  
››› page 136. Doing so also heats up  
the high-voltage battery. This increases the  
available power.  
Switching the ignition oꢂ  
With the ignition on and the vehicle stopped,  
press the ignition/start button once.  
143  
Driving  
OR: leave the vehicle when it is stopped and  
the electroNic parking brake is applied.  
Connecting the drive system  
WARNING  
●
Depress the brake pedal and select a gear  
If the vehicle keys are used negligently or  
without proper attention, accidents and seri-  
ous injuries can occur.  
The ignition will also switch oꢂ when the ve-  
hicle is stopped, the brake pedal is not de-  
pressed, the electronic parking brake applied  
and the driver releases the seat belt on his/her  
seat.  
position ››› page 146. Visual and audio in-  
dications are given when the drive system  
switches on.  
●
Never leave any key inside the vehicle when  
●
exiting. Otherwise, a child or unauthorised  
person could lock the vehicle, switch on the  
drive system or the ignition and operate the  
electrical equipment, such as the windows.  
If it is not possible to connect the drive sys-  
tem, repeat the procedure. If necessary, per-  
form an emergency start ››› page 145.  
Automatic ignition disconnection  
If the driver leaves the ignition on but walks  
away from the vehicle, taking the vehicle key  
with him/her, the ignition switches oꢂ auto-  
matically after a certain period of time. If the  
front bonnet is opened while the ignition is  
switched on, it does not switch oꢂ automati-  
cally. The electronic parking brake is applied  
automatically when you leave the vehicle.  
WARNING  
NOTICE  
An electric vehicle emits very little noise  
when it is in operation, both when stationary  
and when driving. This means that other road  
users and pedestrians (including children)  
may not hear or notice it, or only with diꢂi-  
culty. This can lead to accidents and injuries,  
e.g. in residential areas, when manoeuvring  
or reversing.  
The ignition and drive system can only be  
switched on if there is a valid vehicle key in-  
side the vehicle.  
Connecting the drive system  
If no valid key is detected in the vehicle interior  
after the ignition has been switched oꢂ, the  
system cannot be switched on again without  
a valid key. A message to this eꢂect will be dis-  
played in the digital cockpit.  
Requirements for connecting the drive sys-  
tem  
Disconnecting the drive system  
The drive system can be connected when the  
following conditions are met:  
Perform the following operations only in the  
order indicated:  
●
The level of charge of the high-voltage bat-  
tery is suꢂicient.  
WARNING  
●
●
●
Stop the vehicle.  
Any accidental movement of the vehicle  
could result in serious injury.  
●
●
There is no charging cable plugged in.  
Park the vehicle ››› page 186.  
Connect the electronic parking brake  
››› page 187.  
Please observe the indications on the Digital  
The temperature of the high-voltage battery  
is within the operating range.  
●
If the gear selector is operated while the  
ignition is switched on, the drive system  
switches on immediately under certain cir-  
●
●
There is a valid key inside the vehicle.  
The seat belt is fastened.  
●
cumstances ››› page 144.  
Cockpit ››› page 21.  
144  
Connecting and disconnecting the drive system  
WARNING  
WARNING  
NOTICE  
When leaving the vehicle, always ensure that  
the electronic parking brake is applied and  
that all doors, windows, rear lid and front  
bonnet are fully closed and locked.  
When leaving the vehicle, always ensure that  
the electronic parking brake is applied and  
that all doors, windows, rear lid and front  
bonnet are fully closed and locked.  
The correct operation of the vehicle is only  
guaranteed with original CUPRA keys.  
e-Sound  
e-Sound is an electronically generated engine  
sound to warn other road users of the pres-  
ence of the electric vehicle.  
Never leave the vehicle with the  
drive system connected  
Electronic immobilizer  
The electronic immobiliser helps to prevent  
the drive system from being connected with  
an unauthorised key and, consequently, the  
vehicle being put in motion.  
If after stopping the vehicle you leave it with  
the drive system switched on and a gear selec-  
ted, the ignition and drive system switch oꢂ  
automatically under certain conditions.  
e-Sound switches on when the drive system is  
switched on.  
As the speed increases, the e-Sound slowly  
fades.  
The vehicle key has an integrated chip which  
automatically deactivates the electronic im-  
mobiliser if there is a valid key inside the pas-  
senger compartment.  
This protects the vehicle against unauthorised  
use.  
WARNING  
The electronic parking brake is applied auto-  
matically ››› page 187.  
If you then wish to continue driving, you have  
to turn the ignition on again ››› page 143, e.g.  
by depressing the brake pedal, along with the  
drive system ››› page 144. If necessary, follow  
the instructions in the Digital Cockpit.  
e-Sound volume and audibility may be limi-  
ted if there is snow or heavy soiling in the  
front grille area. This can cause accidents.  
The electronic immobiliser is automatically ac-  
tivated when there is no longer a valid key in-  
side the vehicle.  
●
Before setting oꢂ, check that the front  
For this reason, the vehicle's drive system can  
only be connected with a correctly coded  
Original CUPRA key. This type of key can be  
purchased from a specialised CUPRA dealer or  
any SEAT network dealer.  
grille area is not too dirty and clean it if nec-  
essary.  
●
The driver should always assume that other  
road users have not heard the vehicle, even if  
e-Sound is switched on.  
Automatic operation of the side light  
For this reason, the engine can only be star-  
ted with a correctly coded Original CUPRA key.  
This type of key can be purchased from a spe-  
cialised CUPRA dealer or any SEAT network  
dealer.  
If the dipped beam is switched on when the ig-  
nition switches oꢂ automatically, the side light  
will turn on until the vehicle is locked, or for a  
maximum of approx. 15 minutes.  
Troubleshooting  
Fault in the electric drive system or the  
high-voltage on-board network  
The control lamp switches on yellow.  
145  
Driving  
A message to this eꢂect is displayed in the Dig-  
ital Cockpit.  
e-Sound does not work  
Gear selection  
The control lamp lights up yellow and an audio  
signal sounds.  
There is a fault in the electric drive system or  
the high-voltage on-board network.  
Gear selector  
A message to this eꢂect is displayed in the Dig-  
ital Cockpit.  
●
Go immediately to a specialised workshop  
and request the electric drive system be  
checked.  
●
Contact a specialised workshop.  
It is possible to continue driving.  
It is possible to continue driving.  
The drive system cannot be connected  
The vehicle key is not recognized  
If an unauthorised vehicle key is used or there  
is a fault in the system, a message to this eꢂect  
is displayed in the Digital Cockpit.  
A message to this eꢂect is displayed in the Dig-  
ital Cockpit.  
If the vehicle key’s button battery is almost or  
fully run out, the key may not be recognized.  
●
●
Use an authorised key.  
Fig. 116 Gear selector with the electronic  
parking brake button.  
If the fault persists, seek specialist assistance.  
An emergency start must be performed:  
●
Place the vehicle key on the base of the cen-  
The vehicle has a forward gear D/B and a re-  
verse gear R.  
tral armrest drawer, as close to the  
as possible.  
symbol  
The gear selector has a button for the elec-  
tronic parking brake. To change from neutral  
N to another position, switch on the ignition,  
depress the brake pedal and turn the selector  
●
Depress the brake pedal or press the igni-  
tion/start button.  
●
The ignition is switched on.  
in the desired direction ››› Fig. 116 (arrow):  
The drive system cannot be switched oꢂ  
An emergency disconnection must be per-  
formed:  
– Permanent forward drive position  
The electric drive system is in the normal  
program (automatic brake energy recupera-  
tion when the eco-eꢂicient driving assistant is  
switched on ››› page 142).  
●
●
Stop the vehicle.  
Press the ignition/start button twice within a  
few seconds, or press and hold it once.  
●
The drive and ignition system switches oꢂ.  
146  
Gear selection  
Stop and start moving uphill  
●
When the TCS is switched oꢂ, the drive  
– Intense braking energy recuperation  
wheels may skid, especially if the road is wet,  
slippery or dirty. This can cause the vehicle to  
be neither steered nor controlled.  
You should use the Auto-Hold function when  
the vehicle's drive system is switched on and  
you stop the vehicle or start driving uphill  
Intense recuperation of braking energy during  
deceleration phases ››› page 142.  
››› page 188.  
– Change between D and B  
WARNING  
When stopping uphill with a gear selected,  
always prevent the vehicle from rolling back-  
wards by depressing the brake pedal or apply-  
ing the electronic parking brake. Do not re-  
lease the brake pedal until you want to move  
oꢂ.  
Change between D and B by turning the  
gear selector forwards one position from D/B  
If the vehicle is left unattended with the drive  
system connected, accidents and serious in-  
juries can occur.  
››› Fig. 116. The selector always returns to  
the initial position. Turning it forwards again  
changes back to D.  
●
Never leave the vehicle unattended with  
the drive system connected.  
●
Always switch oꢂ the ignition. When doing  
– Electronic parking brake  
WARNING  
so, the electronic parking brake is applied  
automatically.  
The drive wheels are locked mechanically.  
Only apply it when the vehicle is stationary  
››› page 187.  
If the wrong gear position is selected, control  
of the vehicle may be lost, resulting in an ac-  
cident and serious injury.  
●
When parking or leaving the vehicle, always  
check that the electronic parking brake is  
applied.  
●
Never accelerate when selecting a gear po-  
sition.  
●
When leaving the vehicle, always make sure  
– Neutral  
that all the doors, windows, rear lid and bon-  
net are fully closed and locked.  
The electric drive system is in the neutral  
position. No movement is transmitted to the  
wheels and the braking eꢂect of the electric  
engine does not occur.  
WARNING  
●
When the drive system is switched on and  
gear position D/B or R is selected, the vehicle  
should be stopped by depressing the brake  
pedal.  
Rapid acceleration can cause loss of traction  
and the vehicle skidding, especially on slip-  
pery roads. This could cause loss of control of  
the vehicle, accidents and serious injury.  
●
Never engage reverse gear while the vehi-  
– Reverse gear  
cle is in motion.  
●
Only accelerate quickly if visibility,  
Reverse gear is selected. Only select this posi-  
tion only when the vehicle is stationary.  
weather, road and traꢂic conditions permit,  
and if your vehicle’s deceleration behaviour  
and driving style do not endanger other road  
users.  
Driving down slopes  
When driving downhill, the braking energy re-  
cuperation should be activated whenever pos-  
●
Always adapt the driving style to traꢂic  
conditions.  
sible ››› page 142.  
147  
Driving  
●
Contact a specialised workshop.  
Electronic steering column lock  
NOTICE  
The steering column locks electronically:  
●
When stopping uphill while a gear is se-  
NOTICE  
lected, do not depress the accelerator to  
prevent the vehicle from rolling backwards.  
Press the brake pedal to avoid unnecessarily  
overloading the electric drive system.  
●
Stop the vehicle and connect the electronic  
The electric drive system may be damaged if  
the vehicle is moved while the ignition and  
electric drive system switched oꢂ, or with the  
12-volt battery discharged for a long period  
of time or at high speed. The vehicle can  
only be towed if certain conditions are met  
parking brake ››› page 187.  
●
If the ignition is switched on, press the igni-  
tion/start button or  
●
Never allow the vehicle to move with the  
●
Open the driver’s door; this switches the ig-  
neutral position N selected, especially when  
the drive system is switched oꢂ.  
nition oꢂ. The steering column is locked.  
››› page 275.  
Steering assist  
Troubleshooting  
This help assists the driver in critical situations.  
It recommends turning the steering wheel  
to perform a corrective manoeuvre (counter-  
steering), turning slightly to avoid skidding  
Steering  
Electric drive system overheated  
Information relating to diꢂerent  
vehicle processes.  
The warning lamp lights up red.  
›››  
.
The electric drive system has overheated. A  
warning in this regard is displayed in the Digital  
Cockpit.  
To make the vehicle more diꢂicult to steal, al-  
ways lock the steering before leaving the it.  
WARNING  
●
●
Stop the vehicle immediately!  
If the power steering does not work, much  
more force is required to turn the steering  
wheel, which can make it diꢂicult to control  
the vehicle.  
Park the vehicle outdoors as soon as it is  
Steering  
possible and safe to do so.  
On vehicles with electromechanical steering,  
the power steering automatically adjusts ac-  
cording to the driving speed, the steering  
wheel torque and the orientation of the  
wheels. The electromechanical steering only  
work with the drive system connected.  
●
●
●
Connect the drive system.  
Do not top up coolant!  
●
The power steering only works with the  
drive system connected.  
Seek specialist assistance.  
WARNING  
and  
Braking energy cannot be re-  
If the power steering does not work or does  
not work properly, considerably more force  
than usual will have to be applied to move the  
steering wheel.  
Along with the ESC, steering assist helps the  
driver to control the vehicle’s steering in  
some critical driving situations. However, the  
driver is ultimately responsible for steering  
the vehicle at all times. Power-assisted steer-  
ing does not remove this responsibility.  
cuperated  
The control lamps light up yellow.  
There is a failure in the brake energy recupera-  
tion. Autonomy may be limited.  
148  
DriveProꢀles  
●
Please note the warnings displayed in the  
Troubleshooting  
Selecting a driving proꢀle  
Digital Cockpit.  
●
Steering fault  
If the control lamp continues ꢀashing after  
the ignition has been switched on, do not con-  
tinue driving. Seek specialist assistance.  
The warning lamp lights up or ꢀashes red.  
There is a fault in the electromechanical steer-  
ing or the electronic steering column lock.  
Drive Proꢀles  
●
●
Stop driving! Seek specialist assistance.  
If the warning lamp lights up red, the steer-  
Introduction  
ing may be stiꢂ because the power steering is  
not working.  
The driver can use the drive proꢁles to adapt  
various features of the vehicle's systems to the  
current driving situation, the desired driving  
comfort and an economical driving style. Some  
of the systems that can be adapted are the  
suspension, steering, drive system and air con-  
ditioning.  
●
If the warning lamp ꢁashes red, the steering  
Fig. 117 Multifunction steering wheel:  
DRIVE and CUPRA buttons for selecting and  
changing the driving proꢀle.  
column cannot be unlocked.  
●
Do not allow the vehicle to be towed on its  
own wheels.  
The drive proꢁle can be selected when the ig-  
nition is switched on and the vehicle is station-  
Steering fault  
Depending on the vehicle’s equipment, vari-  
ous drive proꢁles can be selected. The degree  
of inꢀuence of the vehicle's systems on the dif-  
ferent drive proꢁles depends on the vehicle’s  
equipment.  
ary or moving ›››  
.
The control lamp lights up or ꢀashes yellow.  
The steering is stiꢂer or reacts more sensitively  
than usual.  
Selecting a driving proꢀle  
●
●
Press the  
> Drive Proꢀle function button.  
> Vehicle  
The control lamp lights up and remains lit:  
OR: Press the function button  
●
Switch the drive system back on and drive  
Vehicles with adaptive suspension (DCC)  
settings > Drive Proꢀle to display the available  
slowly for a short distance.  
proꢁles.  
When driving, the adaptive suspension (DCC)  
continuously adapts the suspension to the  
terrain and the driving situation in question.  
When doing so, the DCC also takes into ac-  
count the vehicle's conꢁguration in the selec-  
ted drive proꢁle.  
●
Contact a specialist workshop if the control  
●
OR: Press the function button , slide your  
ꢁnger horizontally across the screen to Drive  
Proꢀle. Press to change the driving proꢁle  
lamp remains on.  
The control lamp ꢁashes:  
or double press on the icon to show the availa-  
ble proꢁles.  
●
Turn the steering wheel slightly from one  
side to the other.  
●
OR: With the Infotainment System turned  
●
Turn oꢂ the ignition and turn it on again.  
oꢂ, by pressing on the Drive Proꢀle icon, the  
available driving proꢁles will be displayed.  
149  
Driving  
OR: Press the 1) button on the multifunc-  
●
Driving  
proꢀle  
Characteristics  
WARNING  
tion steering wheel ››› Fig. 117 to activate the  
Please note that if the road surface is slippery  
or wet, the kick-down feature could cause  
the driving wheels to spin, which could result  
in skidding.  
CUPRA driving proꢁle.  
It gives the vehicle a decidedly  
sportier nature, and makes for  
maximum performance.  
OR: Repeatedly press the 1) button on the  
●
multifunction steering wheel ››› Fig. 117 to  
switch between driving proꢁles.  
Selecting the CUPRA driving  
proꢀle activates the eBoost  
function, which allows more  
power to be delivered when  
the accelerator pedal is de-  
pressed.  
Characteristics of driving proꢀles  
CUPRAb)  
Displaying the drive proꢀle information  
●
To display more information on the selected  
Driving  
proꢀle  
Characteristics  
drive proꢁle, press Informationin the info-  
tainment system.  
Sets the vehicle to a low con-  
sumption status, favouring an  
energy saving driving style by  
limiting the maximum speed  
and power.  
It allows you to personalise the  
conꢀguration. The functions  
that can be adjusted depend  
on the equipment ꢀtted in the  
vehicle.  
WARNING  
Range  
Individual  
Adjusting the driving proꢀle while driving can  
distract attention from traꢂic and cause acci-  
dents.  
It permits more relaxed and  
comfortable driving, for exam-  
ple on long motorway jour-  
neys. The performance is su-  
perior to Rangea) mode.  
a) On models ꢀtted with adaptive suspension (DCC)  
it permits a gentle adjustment of the drive train.  
b) Depending on the version.  
●
Always drive as carefully and responsibly as  
possible.  
Comfort  
Kick-down  
Note  
Depending on the version, the kick-down de-  
vice allows maximum acceleration with the  
gear selector in the D/B position in any driving  
proꢁle.  
Provides a complete dynamic  
performance in the vehicle,  
enabling the user a more  
sporty driving style.  
When you switch the ignition oꢂ and on  
again, the Comfort drive proꢀle is activated  
by default.  
Perform-  
ance  
To use it, fully depress the accelerator pedal  
through the point of resistance. This uses the  
vehicle's maximum acceleration.  
1)  
Depending on the version.  
150  
Brakingsystem  
in city traꢂic and for short distances, or for  
sporty driving, brake pad thickness should be  
checked regularly at a specialist workshop.  
Troubleshooting  
WARNING  
Driving with worn brake pads or a defective  
brake system can lead to accidents and seri-  
ous injuries.  
Adaptive suspension (DCC) fault  
Driving with wet brakes, e.g. after driving  
through water, in heavy rain or after washing  
the vehicle, braking performance may be af-  
fected by wet brake discs, or even frozen discs  
in winter. The driver should be ready to brake  
harder.  
The control lamp switches on yellow. The in-  
strument cluster screen may display the mes-  
sage Fault: Suspension.  
●
If you suspect that the brake pads are worn  
or that the brake system is faulty, have the  
brake pads checked immediately by a spe-  
cialist workshop and replaced if they are  
worn.  
●
Have the system checked by a specialised  
workshop.  
If the brake discs and pads have a layer  
of salt on them, the braking performance is  
reduced and the braking distance increases.  
When driving on salted roads without brak-  
ing for some time, the layer of salt should  
be removed by carefully applying the brakes  
The drive proꢀles or vehicle systems do not  
behave as expected  
WARNING  
The braking performance of new brake pads  
is not optimal.  
●
Please note that diꢂerent vehicle systems are  
conꢁgured according to the selected driving  
proꢁle.  
●
During the ꢀrst 300 km, new brake pads do  
a few times ››› . Braking intensity should  
be higher than the deceleration achieved by  
brake energy recuperation, in order to clean  
oꢂ the layer of salt with the brake pad friction.  
not provide maximum braking power and still  
have to “settle”. This can be counteracted by  
applying more pressure to the brake pedal.  
Braking system  
●
When brake pads are new, drive with extra  
Information about the brakes  
care to reduce the risk of accidents, serious  
injury or loss of control of the vehicle.  
Corrosion on the brake discs and dirt on the  
brake pads increase if the vehicle is left unused  
for a long time, if it is not driven for many kil-  
ometres or the brakes are used insuꢂiciently.  
If, due to the energy recuperation eꢂect, the  
brakes are not used, or are rarely used, or if  
there is corrosion, it is advisable to clean the  
discs and pads by braking hard several times  
when driving at high speeds. When doing so,  
select gear N, so that energy recuperation is  
not used when braking. Make sure that you do  
not endanger any other vehicles or road users  
During the ꢁrst 200 to 300 km, new brake  
pads do not provide maximum braking power  
●
Only perform hard braking to clean the  
brake system when permitted by the traꢂic  
situation. Do not endanger the occupants of  
other vehicles. Accident hazard!  
and still have to “settle” ››› . When running  
in the brake pads, the emergency braking  
distance is longer than after they have been  
run in. During the run-in, avoid sharp braking  
and situations that place a lot of demand on  
the brakes, e.g. driving too close to another  
vehicle.  
●
When running in new brake pads, do not  
drive too close to other vehicles or cause sit-  
uations that would require the brakes to be  
applied heavily.  
Brake pad wear depends to a large extent on  
the conditions in which the vehicle is used, and  
driving style. If the vehicle is frequently used  
›››  
.
151  
Driving  
Troubleshooting  
WARNING  
WARNING  
When the brakes overheat, their braking per-  
formance drops and the braking distance in-  
creases.  
When braking manoeuvres are started auto-  
matically, the brake pedal may move auto-  
matically in the application direction. Do not  
put your foot under the brake pedal. Risk of  
injury!  
Defect in the brake system  
The warning lamp lights up red. A message may  
also be displayed.  
●
When driving downhill, particular demand  
is placed on the brakes and they heat up very  
quickly.  
Stop driving!  
●
Inform a specialist workshop and request a  
brake system inspection.  
●
When on a long downhill, reduce speed  
Note  
and select a higher braking energy recuper-  
ation level. This makes use of the electric  
motor braking eꢂect and the brakes are not  
required as much.  
Never let the brakes “drag” by leaving your  
foot on the pedal when it is not necessary  
to brake. This can cause the brakes to over-  
heat, resulting in increased brake travel and  
wear. Please consider the important notes on  
Brake pad wear indicator  
The control lamp switches on yellow.  
The front brake pads are worn.  
●
If you wish to retroꢀt a front spoiler, inte-  
gral trim or other accessories, ensure that  
the air inlet around the brakes is not reduced,  
as otherwise the brake system could over-  
heat. Please also note the information on  
brake ꢁuid ››› page 289.  
●
●
Contact a specialised workshop immediately.  
Get all the brake pads inspected and replace  
if necessary.  
Note  
brake ꢁuid ››› page 289.  
●
Regularly check the thickness of the front  
brake pads visually through the holes in the  
rims or from the underside of the vehicle.  
If necessary, the wheels should be removed  
for a more thorough inspection. To do so,  
CUPRA recommends going to a specialised  
CUPRA dealer or any SEAT dealership.  
Brake assist systems  
WARNING  
Wet, frozen or salt-covered brakes take lon-  
ger to brake and increases the braking dis-  
tance.  
Information relating to brake assist  
systems  
●
●
Test the brakes carefully.  
Brake assist systems can help the driver in crit-  
ical driving or braking situations. The driver is  
●
When inspecting the front brake pads, the  
Always dry the brakes and free them from  
rear axle drum brake shoes should also be  
checked. The check is made through a hole  
provided for this purpose in the rear of the  
drum. A plug has to be removed for this pur-  
pose. To do so, CUPRA recommends going  
to a specialised CUPRA dealer or any SEAT  
dealership.  
ice and salt by braking repeatedly, if permit-  
ted by visibility, weather, road surface and  
traꢂic conditions.  
responsible for driving safely ›››  
.
When the brake assist systems are regulating  
the brakes, the brake pedal may move or make  
noises. Even so, continue to brake with the  
necessary force and control the trajectory of  
the vehicle if necessary.  
152  
Brake assistsystems  
Depending on the equipment, the ESC and  
TCS settings may be changed in the vehicle.  
After disconnecting the ignition, the assistance  
of the brake servo is progressively reduced. If  
you continue to hold the vehicle in place with  
the brake pedal, messages are displayed on  
the instrument cluster screen. In this case, the  
brake servo function is restricted.  
Brake assist (BAS)  
Brake assist (BAS) can help to reduce the brak-  
ing distance. Brake Assist increases the pres-  
sure exerted by the driver when the brake  
pedal is depressed quickly in an emergency.  
●
The ESC, ABS and TCS can only operate cor-  
rectly if the four wheels are ꢁtted with the  
stipulated tyres ›››  
.
●
If a fault occurs in the ABS, the ESC, TCS and  
Once stopped, immobilise the vehicle to pre-  
vent it from moving ››› page 186.  
Electronic diꢂerential lock (EDS and XDS)  
EDS also cease to function.  
The EDS automatically brakes skidding wheels  
and transmits the driving force to the other  
driving wheels.  
Electronic Stability Control (ESC)  
Brake blending  
The ESC helps to reduce the risk of skidding  
and to improve stability in certain driving situa-  
The regulated application of the brakes blends  
the braking eꢂect of the electric motor in en-  
ergy recuperation and the mechanical braking  
by the driver.  
The XDS improves traction by applying the  
brakes to keep the vehicle in its lane.  
tions ›››  
.
Multi-collision brake  
Traction control (TCS)  
The multi-collision brake automatically triggers  
braking if the airbag control unit detects a col-  
lision in the event of an accident.  
The TCS reduces the driving force on skidding  
wheels and adapts this force to suit the road  
surface conditions. The TCS facilitates starting,  
WARNING  
Smart brake assist technology cannot over-  
come the limits imposed by the laws of phys-  
ics and only works within the limits of the sys-  
tems. Driving at high speed on icy, slippery or  
wed road surfaces can cause a loss of control  
of the vehicle and serious injury to the driver  
and passengers.  
acceleration and hill climbing ›››  
.
Automatic braking requirements:  
●
The driver is not pressing the accelerator  
Electronic brake pressure distribution (EBV)  
pedal.  
Electronic brake force distribution (EBV) regu-  
lates the braking force between the front and  
rear axles. Excessive braking of the rear axle is  
avoided and the vehicle remains stable during  
the braking operation.  
Electromechanical brake servo (eBKV)  
●
Adapt your speed and driving style at all  
With the ignition switched on, the electrome-  
chanical brake servo (eBKV) supplements the  
force exerted by the foot by increasing the  
pressure that the driver exerts on the brake  
pedal ››› . When a driver assistance system  
apples the brakes, e.g. ACC when regulating  
the speed, or during emergency braking, the  
brake pedal may move automatically.  
times to suit visibility, weather, road and traf-  
ꢀc conditions. Never take any risk that com-  
promises safety.  
Anti-lock braking system (ABS),  
●
Brake assist systems cannot prevent an ac-  
cident if you are driving too close to other  
vehicles.  
The ABS can prevent the wheels from locking  
up under braking until shortly before the vehi-  
cle comes to a stop, and helps the driver main-  
tain control of the steering and the vehicle  
›››  
.
153  
Driving  
Connecting and disconnecting the  
ESC and TCS  
●
Always use suitable tyres. Driving stability  
WARNING  
depends on tyre grip.  
The ESC Sport mode should only be switched  
on if the traꢂic conditions and your driving  
ability allow you to do so safely.  
●
Always leave the area under the pedals  
The ESC is switched on automatically when the  
engine is started, and only works when the en-  
gine is running and includes the ABS, EDS and  
TCS systems.  
free so that the brake pedal can move unhin-  
dered.  
●
With ESC in Sport mode, the stabilising  
function will be limited to allow for a sportier  
drive. There is a risk of skidding and losing  
control of the vehicle.  
WARNING  
Disconnecting and connecting the ESC in  
“Sport” mode  
The eꢂiciency of the ESC can be signiꢀcantly  
reduced if components or systems that af-  
fect the driving dynamics are not properly  
maintained or are not working properly. This  
can particularly occur if changes are made  
to the suspension or unauthorised rim/tyre  
combinations are used.  
●
If the ESC is deactivated, the vehicle stabili-  
sation function is not available.  
The ECS in “Sport” mode can be turned on  
or oꢂ in the infotainment system: press the  
Note  
function button  
> Assistants > ESC menu  
If “Sport” mode is selected, the speed regu-  
lator is disconnected.  
››› page 35.  
●
Ensure that vehicle conversions and modi-  
When “Sport” mode is connected, the inter-  
ventions of the ESC to stabilise the vehicle,  
and the traction control (TCS) interventions  
are limited. In addition, the control lamp  
lights up on the instrument cluster.  
ꢀcations are only made by specialised work-  
shops.  
Troubleshooting  
●
Always use suitable tyres. Driving stability  
depends on tyre grip.  
The electromechanical brake servo is  
not working  
Disconnecting and connecting the ESC  
WARNING  
Stop driving  
The ESC can be switched on and oꢂ in the  
When driving without a brake servo or with  
restricted brake servo functions, the braking  
distance can increase considerably and can  
cause accidents and serious injuries.  
The warning lamp lights up red.  
infotainment system: press  
> Assistants >  
ESC Menu ››› page 35.  
When the ESC is disconnected the control  
warning lamp lights up on the instrument  
cluster.  
A message is displayed as appropriate. Depress  
the brake pedal hard because the braking dis-  
tance will increase due to the lack of brake as-  
sist from the brake servo.  
●
If the brake servo is not working, the brake  
pedal has to be pressed harder, as the brak-  
ing distance increases due to the lack of as-  
sistance from the servo brake.  
●
You should obtain professional assistance  
immediately.  
●
Always leave the area under the pedals  
free so that the brake pedal can move unhin-  
dered.  
154  
Brake assistsystems  
The brake assist systems make noises  
There is a fault in the electromechanical  
brake servo  
When the described brake assist systems inter-  
vene, you may hear noises.  
The control lamp switches on yellow.  
A message is displayed for a few seconds.  
WARNING  
Depressing the brake pedal may cause vibra-  
tions. The brake pedal has to be pressed  
harder because the braking distance increases  
due to the reduced brake servo assistance.  
●
When the ignition is switched on, the sta-  
tus of the brake system and the brake as-  
sist functions are automatically checked. The  
control lamps on the instrument cluster light  
up brieꢁy and then go out. Any indicator  
lamp that remains on indicates a fault. Seek  
qualiꢀed technical assistance immediately.  
●
Contact a specialised workshop.  
The ABS does not work properly or does  
●
If the brake system warning light comes  
not work at all  
on together with the control lamp, the ABS  
regulation function may not work and the  
rear wheels may lock relatively quickly when  
braking. This can lead to loss of control of  
the vehicle! If possible, slow down and drive  
slowly and carefully to the nearest specialist  
workshop to have the brake system inspec-  
ted. During this journey, avoid heavy braking  
and any sudden manoeuvres.  
The control lamp switches on yellow.  
●
Contact a specialised workshop. The vehi-  
cle’s brakes still work without the ABS.  
The ESC or TCS is regulating  
The control lamp ꢀashes yellow.  
●
If the control lamp does not go out, or  
ESC fault  
comes on while driving, it means that the  
ABS is not working properly. The vehicle can  
only be stopped using normal braking (with-  
out ABS). In this case the protective ABS  
function will not be available. Go to a special-  
ised workshop as soon as possible.  
The control lamp switches on yellow. The ESC  
has been switched oꢂ.  
There is a fault or defect.  
●
●
Turn oꢂ the ignition and turn it on again.  
If possible, drive for a short distance at 15-20  
km/h (9-12 mph).  
●
If the control lamp is still on, go to a speci-  
alised workshop.  
155  

Related Topics

Popular Owner Manuals