2002-2008 Cupra Born SUV Driving -> Brake assist systems User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Driving -> Brake assist systems for Your Cupra Born SUV First Generation (2002-2008)

Driving  
Troubleshooting  
WARNING  
WARNING  
When the brakes overheat, their braking per-  
formance drops and the braking distance in-  
creases.  
When braking manoeuvres are started auto-  
matically, the brake pedal may move auto-  
matically in the application direction. Do not  
put your foot under the brake pedal. Risk of  
injury!  
Defect in the brake system  
The warning lamp lights up red. A message may  
also be displayed.  
●
When driving downhill, particular demand  
is placed on the brakes and they heat up very  
quickly.  
Stop driving!  
●
Inform a specialist workshop and request a  
brake system inspection.  
●
When on a long downhill, reduce speed  
Note  
and select a higher braking energy recuper-  
ation level. This makes use of the electric  
motor braking eꢀect and the brakes are not  
required as much.  
Never let the brakes “drag” by leaving your  
foot on the pedal when it is not necessary  
to brake. This can cause the brakes to over-  
heat, resulting in increased brake travel and  
wear. Please consider the important notes on  
Brake pad wear indicator  
The control lamp switches on yellow.  
The front brake pads are worn.  
●
If you wish to retroꢁt a front spoiler, inte-  
gral trim or other accessories, ensure that  
the air inlet around the brakes is not reduced,  
as otherwise the brake system could over-  
heat. Please also note the information on  
brake ꢂuid ››› page 289.  
●
●
Contact a specialised workshop immediately.  
Get all the brake pads inspected and replace  
if necessary.  
Note  
brake ꢂuid ››› page 289.  
●
Regularly check the thickness of the front  
brake pads visually through the holes in the  
rims or from the underside of the vehicle.  
If necessary, the wheels should be removed  
for a more thorough inspection. To do so,  
CUPRA recommends going to a specialised  
CUPRA dealer or any SEAT dealership.  
Brake assist systems  
WARNING  
Wet, frozen or salt-covered brakes take lon-  
ger to brake and increases the braking dis-  
tance.  
Information relating to brake assist  
systems  
●
●
Test the brakes carefully.  
Brake assist systems can help the driver in crit-  
ical driving or braking situations. The driver is  
●
When inspecting the front brake pads, the  
Always dry the brakes and free them from  
rear axle drum brake shoes should also be  
checked. The check is made through a hole  
provided for this purpose in the rear of the  
drum. A plug has to be removed for this pur-  
pose. To do so, CUPRA recommends going  
to a specialised CUPRA dealer or any SEAT  
dealership.  
ice and salt by braking repeatedly, if permit-  
ted by visibility, weather, road surface and  
traꢀic conditions.  
responsible for driving safely ›››  
.
When the brake assist systems are regulating  
the brakes, the brake pedal may move or make  
noises. Even so, continue to brake with the  
necessary force and control the trajectory of  
the vehicle if necessary.  
152  
Brake assistsystems  
Depending on the equipment, the ESC and  
TCS settings may be changed in the vehicle.  
After disconnecting the ignition, the assistance  
of the brake servo is progressively reduced. If  
you continue to hold the vehicle in place with  
the brake pedal, messages are displayed on  
the instrument cluster screen. In this case, the  
brake servo function is restricted.  
Brake assist (BAS)  
Brake assist (BAS) can help to reduce the brak-  
ing distance. Brake Assist increases the pres-  
sure exerted by the driver when the brake  
pedal is depressed quickly in an emergency.  
●
The ESC, ABS and TCS can only operate cor-  
rectly if the four wheels are ꢀtted with the  
stipulated tyres ›››  
.
●
If a fault occurs in the ABS, the ESC, TCS and  
Once stopped, immobilise the vehicle to pre-  
vent it from moving ››› page 186.  
Electronic diꢀerential lock (EDS and XDS)  
EDS also cease to function.  
The EDS automatically brakes skidding wheels  
and transmits the driving force to the other  
driving wheels.  
Electronic Stability Control (ESC)  
Brake blending  
The ESC helps to reduce the risk of skidding  
and to improve stability in certain driving situa-  
The regulated application of the brakes blends  
the braking eꢁect of the electric motor in en-  
ergy recuperation and the mechanical braking  
by the driver.  
The XDS improves traction by applying the  
brakes to keep the vehicle in its lane.  
tions ›››  
.
Multi-collision brake  
Traction control (TCS)  
The multi-collision brake automatically triggers  
braking if the airbag control unit detects a col-  
lision in the event of an accident.  
The TCS reduces the driving force on skidding  
wheels and adapts this force to suit the road  
surface conditions. The TCS facilitates starting,  
WARNING  
Smart brake assist technology cannot over-  
come the limits imposed by the laws of phys-  
ics and only works within the limits of the sys-  
tems. Driving at high speed on icy, slippery or  
wed road surfaces can cause a loss of control  
of the vehicle and serious injury to the driver  
and passengers.  
acceleration and hill climbing ›››  
.
Automatic braking requirements:  
●
The driver is not pressing the accelerator  
Electronic brake pressure distribution (EBV)  
pedal.  
Electronic brake force distribution (EBV) regu-  
lates the braking force between the front and  
rear axles. Excessive braking of the rear axle is  
avoided and the vehicle remains stable during  
the braking operation.  
Electromechanical brake servo (eBKV)  
●
Adapt your speed and driving style at all  
With the ignition switched on, the electrome-  
chanical brake servo (eBKV) supplements the  
force exerted by the foot by increasing the  
pressure that the driver exerts on the brake  
pedal ››› . When a driver assistance system  
apples the brakes, e.g. ACC when regulating  
the speed, or during emergency braking, the  
brake pedal may move automatically.  
times to suit visibility, weather, road and traf-  
ꢁc conditions. Never take any risk that com-  
promises safety.  
Anti-lock braking system (ABS),  
●
Brake assist systems cannot prevent an ac-  
cident if you are driving too close to other  
vehicles.  
The ABS can prevent the wheels from locking  
up under braking until shortly before the vehi-  
cle comes to a stop, and helps the driver main-  
tain control of the steering and the vehicle  
›››  
.
153  
Driving  
Connecting and disconnecting the  
ESC and TCS  
●
Always use suitable tyres. Driving stability  
WARNING  
depends on tyre grip.  
The ESC Sport mode should only be switched  
on if the traꢀic conditions and your driving  
ability allow you to do so safely.  
●
Always leave the area under the pedals  
The ESC is switched on automatically when the  
engine is started, and only works when the en-  
gine is running and includes the ABS, EDS and  
TCS systems.  
free so that the brake pedal can move unhin-  
dered.  
●
With ESC in Sport mode, the stabilising  
function will be limited to allow for a sportier  
drive. There is a risk of skidding and losing  
control of the vehicle.  
WARNING  
Disconnecting and connecting the ESC in  
“Sport” mode  
The eꢀiciency of the ESC can be signiꢁcantly  
reduced if components or systems that af-  
fect the driving dynamics are not properly  
maintained or are not working properly. This  
can particularly occur if changes are made  
to the suspension or unauthorised rim/tyre  
combinations are used.  
●
If the ESC is deactivated, the vehicle stabili-  
sation function is not available.  
The ECS in “Sport” mode can be turned on  
or oꢁ in the infotainment system: press the  
Note  
function button  
> Assistants > ESC menu  
If “Sport” mode is selected, the speed regu-  
lator is disconnected.  
››› page 35.  
●
Ensure that vehicle conversions and modi-  
When “Sport” mode is connected, the inter-  
ventions of the ESC to stabilise the vehicle,  
and the traction control (TCS) interventions  
are limited. In addition, the control lamp  
lights up on the instrument cluster.  
ꢁcations are only made by specialised work-  
shops.  
Troubleshooting  
●
Always use suitable tyres. Driving stability  
depends on tyre grip.  
The electromechanical brake servo is  
not working  
Disconnecting and connecting the ESC  
WARNING  
Stop driving  
The ESC can be switched on and oꢁ in the  
When driving without a brake servo or with  
restricted brake servo functions, the braking  
distance can increase considerably and can  
cause accidents and serious injuries.  
The warning lamp lights up red.  
infotainment system: press  
> Assistants >  
ESC Menu ››› page 35.  
When the ESC is disconnected the control  
warning lamp lights up on the instrument  
cluster.  
A message is displayed as appropriate. Depress  
the brake pedal hard because the braking dis-  
tance will increase due to the lack of brake as-  
sist from the brake servo.  
●
If the brake servo is not working, the brake  
pedal has to be pressed harder, as the brak-  
ing distance increases due to the lack of as-  
sistance from the servo brake.  
●
You should obtain professional assistance  
immediately.  
●
Always leave the area under the pedals  
free so that the brake pedal can move unhin-  
dered.  
154  
Brake assistsystems  
The brake assist systems make noises  
There is a fault in the electromechanical  
brake servo  
When the described brake assist systems inter-  
vene, you may hear noises.  
The control lamp switches on yellow.  
A message is displayed for a few seconds.  
WARNING  
Depressing the brake pedal may cause vibra-  
tions. The brake pedal has to be pressed  
harder because the braking distance increases  
due to the reduced brake servo assistance.  
●
When the ignition is switched on, the sta-  
tus of the brake system and the brake as-  
sist functions are automatically checked. The  
control lamps on the instrument cluster light  
up brieꢂy and then go out. Any indicator  
lamp that remains on indicates a fault. Seek  
qualiꢁed technical assistance immediately.  
●
Contact a specialised workshop.  
The ABS does not work properly or does  
●
If the brake system warning light comes  
not work at all  
on together with the control lamp, the ABS  
regulation function may not work and the  
rear wheels may lock relatively quickly when  
braking. This can lead to loss of control of  
the vehicle! If possible, slow down and drive  
slowly and carefully to the nearest specialist  
workshop to have the brake system inspec-  
ted. During this journey, avoid heavy braking  
and any sudden manoeuvres.  
The control lamp switches on yellow.  
●
Contact a specialised workshop. The vehi-  
cle’s brakes still work without the ABS.  
The ESC or TCS is regulating  
The control lamp ꢂashes yellow.  
●
If the control lamp does not go out, or  
ESC fault  
comes on while driving, it means that the  
ABS is not working properly. The vehicle can  
only be stopped using normal braking (with-  
out ABS). In this case the protective ABS  
function will not be available. Go to a special-  
ised workshop as soon as possible.  
The control lamp switches on yellow. The ESC  
has been switched oꢁ.  
There is a fault or defect.  
●
●
Turn oꢁ the ignition and turn it on again.  
If possible, drive for a short distance at 15-20  
km/h (9-12 mph).  
●
If the control lamp is still on, go to a speci-  
alised workshop.  
155  

Related Topics

Popular Owner Manuals