2002-2008 Cupra Born SUV High-voltage battery -> Charging the high-voltage battery User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

High-voltage battery -> Charging the high-voltage battery for Your Cupra Born SUV First Generation (2002-2008)

High-voltage battery  
●
Charging with alternating current (AC) at a  
●
Always respect the stipulated order of the  
Charging the high-voltage  
battery  
household socket ››› page 74:  
operations to avoid the risk of suꢁering an  
electric shock or serious injuries due to the  
residual energy in the charging accumulator.  
The electrical installation of the house must  
have been checked and be in perfect working  
order ››› . Due to the large capacity of the  
battery and the low power of this method, a full  
charge will take more than 20 hours.  
●
Please observe the safety and handling  
Introduction  
instructions of the charging cable supplied  
with the vehicle ››› page 85.  
●
When charging, only use power sockets  
●
Charging with direct current (DC) at a fast  
that are appropriately ꢀtted, have been  
checked and are not damaged, as well as  
electrical installations that are in perfect  
working order. Duly qualiꢀed technicians  
should check the power sockets and the  
electrical installation on a regular basis.  
charging station ››› page 75:  
It is the most powerful type of charge. The  
charging time diminishes signiꢀcantly. Please  
note the information on charging frequently  
with direct current (DC) ›››  
.
●
Never charge the vehicle in places where  
there is a danger of explosion. The compo-  
nents of the charging cable can cause sparks  
and, therefore, may ignite ꢂammable fumes  
or explosives.  
Protection against current leakage  
Fig. 65 Location of the high-voltage  
battery.  
The vehicle is ꢀtted with a direct current (DC)  
leakage protection device. This prevents any  
current leakage that may occur during charg-  
ing from reaching the house's electrically in-  
stallation through the charging cable.  
●
Always protect the connectors from mois-  
ture and from water and other ꢂuids getting  
inside directly.  
Check that the drive system is deactivated and  
that the charging cable and infrastructure are  
in a perfect state of repair.  
●
For safety reasons, never perform other  
WARNING  
works on the vehicle while charging.  
●
Always complete the charging process be-  
If the battery is charged in an inappropri-  
ate manner, if no consideration is given to  
the appropriate safety measures or the high-  
voltage battery is used in an inadequate  
manner, this could lead to short circuits,  
electrical shocks, explosions, ꢀres, burns and  
serious injuries, even death.  
Types of charging  
fore unplugging the connector from the  
electrical network. Otherwise the charging  
cable and the electrical installation may also  
be damaged.  
The following charging types are possible for  
the vehicle:  
●
Charging with alternating current (AC) at a  
public or home charging station ››› page 74:  
Charges at high power. The maximum achiev-  
able charging power depends on the charging  
station and charging cable that is used and the  
performance of the vehicle's charger.  
72  
Chargingthehigh-voltagebattery  
●
In the event of very low or very high tem-  
Compatibility between vehicles and charg-  
ing infrastructure  
WARNING  
peratures, it may only be possible to charge  
the high-voltage battery in a limited manner.  
If the vehicle is driven with a very low a  
charge level of the high-voltage battery, the  
vehicle may stall in traꢁic, causing serious  
damage or accidents and injuries.  
The following indicators according to the  
EN 17186 standard provide information about  
whether the infrastructure's charging connec-  
Identiꢀcation of compatible charg-  
ing infrastructure  
tors are suitable for the vehicle ›››  
.
NOTICE  
Indicators ››› Fig. 66  
In the vehicle  
Fast charging with direct current (DC) uses  
very high power. Frequent use of fast charg-  
ing can permanently reduce the charging ca-  
pacity of the high-voltage battery.  
At the charging station  
●
The battery should preferably be charged  
Indicators ››› Fig. 67  
with alternating current (AC) from a public or  
domestic charging station.  
Voltage up to 500 volts  
Fig. 66 Identiꢀcation of alternating current  
(AC) and type 2 connector.  
Voltage of up to 1000 volts.  
The indicators are located on the vehicle's  
charging socket, on components of the lo-  
cal charging infrastructure (charging station,  
socket) and on the charging cable. The indi-  
cators refer to charging connection standards  
according to IEC 62196.  
Note  
●
To charge the high-voltage battery us-  
ing alternating current (AC), CUPRA recom-  
mends using a home charging station or an-  
other type of charging station and charging  
with maximum charging power. These charg-  
ing options are more eꢁicient than using a  
domestic power socket.  
WARNING  
Fig. 67 Identiꢀcation of direct current  
(DC) and the vehicle's CCS connector  
●
Please note the technical data on your ve-  
Charging the vehicle at unveriꢀed electrical  
installations can cause serious injury and  
damage.  
hicle's charging power. You can get more in-  
formation from a specialised CUPRA dealer  
or any SEAT network dealer.  
●
If there is no indicator or if the charging in-  
●
The high-voltage battery can only be  
frastructure is unknown, an electrical instal-  
charged at charging stations that meet the  
requirements of the country in questions and  
at least one of the following standards:  
lation expert should be consulted ꢀrst.  
–
IEC 61851 and IEC 62196 (Europe)  
73  
High-voltage battery  
●
Charging cable for domestic power sockets:  
If the charging process indicator lights up red,  
there is a fault ››› page 76.  
Charging with alternating current  
(AC)  
The protection device performs a self-test  
››› page 87.  
●
Interrupt the charging process  
With the vehicle unlocked, the battery  
charging cover opens when it is pressed  
The charging process can be interrupted:  
››› Fig. 68.  
●
●
Unlock the vehicle.  
●
Plug the charging connector into the charg-  
Press the Stop chargingfunction but-  
ing socket. Check that the charging connector  
is fully plugged in.  
ton of the infotainment system. The charging  
process indicator located next to the charg-  
ing socket lights up white . If you want  
The connector locks automatically.  
1
the charging connector to unlock automati-  
cally, the Release connector automatically  
setting must be selected in the charging set-  
The LED (charging process indicator) of  
the charging socket ꢁashes or ꢁashes white  
1
››› Fig. 68 ››› page 76.  
Fig. 68 Behind the battery charging cover  
on the rear right-hand side: Charging  
socket  
tings ››› page 79.  
You can set the charging as required in the  
infotainment system ››› page 81.  
●
Press the Continuebutton to restart the  
process. The charging connector locks. In  
some cases you make need to authenticate  
yourself again in the charging station.  
››› Fig. 68  
Automatic start of the charging process  
1
Charging process display  
If programmed charging is not activated,  
the charging process starts immediately  
To restart the charging process just press the  
function button to start the charging process.  
2
Charging socket  
››› page 79. The external charging infra-  
The battery charger installed in the vehicle  
converts alternating current from the public  
supply into direct current.  
structure must be active.  
After charging  
Most public charging stations require authen-  
tication to start the process. It is important  
to verify that the authentication has been per-  
formed correctly, otherwise it could cause a  
system malfunction.  
When the high-voltage battery is fully charged,  
the charging process display on the charging  
socket lights up green.  
AC charging station or socket cable: The vehi-  
cle’s high-voltage battery can be charged us-  
ing alternating current (AC) through the corre-  
●
●
Unlock the vehicle.  
2
sponding charging socket  
.
Unplug the charging connector from the  
During the charging  
charging socket within 30 seconds.  
Connecting the charging cable  
The charging process indicator on the charg-  
●
Firstly, connect the charging cable to the  
1
ing socket ꢁashes green . The charging con-  
socket, or public or home charging station.  
Next, fully unwind it.  
nector is locked.  
74  
Chargingthehigh-voltagebattery  
●
OR: if Release connector automatically  
The alternating current is converted into direct  
current outside the vehicle. A considerably  
higher charging power is achieved than when  
charging with alternating current (AC).  
Most public charging stations require authen-  
tication to start the process. It is important  
to verify that the authentication has been per-  
formed correctly, otherwise it could cause a  
system malfunction.  
is activated in the charging settings  
››› page 79, the charging connector auto-  
matically unlocks once the charging process is  
complete.  
Public fast-charging station: The high-voltage  
battery can be charged with direct current  
(DC) at an appropriate charging station. The  
charging time diminishes signiꢀcantly.  
●
Disconnect the charging cable from the  
During the charging  
power supply and replace the protective cap.  
The charging process indicator on the charg-  
●
Close the charging cover and make sure you  
1
ing socket ꢁashes green ››› Fig. 69  
.
hear it click into place.  
Use a charging cable less than 30 metres long.  
If the charging process indicator lights up red,  
there is a fault ››› page 76.  
Connecting the charging cable  
Charging with direct current (DC)  
●
●
Unlock the vehicle.  
Interrupt the charging process  
Press the battery's charging socket cover to  
open it.  
The charging process can be stopped before  
the desired state of charge is reached:  
●
Remove the protective cap and hang it on  
3
the hook ››› Fig. 69  
●
Press the STOPfunction button on the info-  
tainment system's display. The charging proc-  
ess indicator located next to the charging  
●
Plug the charging station’s charging connec-  
2
tor into the charging socket ››› Fig. 69  
The connector locks automatically.  
1
socket lights up white ››› Fig. 69 . The  
charging connector is unlocked.  
The LED (charging process indicator) of  
the charging socket ꢁashes or ꢁashes white  
After charging  
Fig. 69 Behind the battery charging cover  
on the rear right-hand side.  
1
››› Fig. 69 ››› page 76  
When the desired state of charge has been  
reached, the charging process indicator on the  
charging socket will light up green.  
Automatic start of charging  
››› Fig. 69  
Switch on the charging station ›››  
.
After charging, the charging connector auto-  
matically unlocks from the charging station.  
1
2
3
Charging process display  
The charging process will start immediately.  
Charging socket  
Protective cap  
75  
High-voltage battery  
●
Unplug the charging connector from the  
White LED  
charging socket.  
●
1
Flashing: establishment of communica-  
●
Place the protective cap on the charging  
tion between the vehicle and the charging  
infrastructure. The charging process is being  
prepared.  
3
socket’s lower connection ››› Fig. 69  
●
Close the cover of the battery charging  
●
Permanently on: no active charging function  
socket until you hear it has engaged.  
Green LED  
NOTICE  
●
2
Flashing: the high-voltage battery is  
charging.  
To use the charging station, bear in mind  
the manufacturer’s indications and usage in-  
structions.  
●
3
Flashing: delayed charging is activated.  
The charging process has not yet started.  
●
4
Permanently on: the charging process has  
completed without any problems.  
Fig. 71 On the inside face of the cover  
of the battery charging socket: sticker  
with information on the charging process  
display.  
Charging process display  
●
Flashes red: emergency charging at reduced  
power due to a failure to recognize the charg-  
ing connector.  
Red LED  
●
Permanently on: there is a fault in the system.  
An LED light on the charging socket ››› Fig. 70  
(arrow) shows the status of the charging proc-  
ess.  
The charging process cannot start or has been  
interrupted.  
Get specialist assistance if the charging proc-  
ess indicator permanently indicates a defect.  
A sticker on the battery charging cover pro-  
vides information on the meaning of the LEDs  
››› Fig. 71.  
Charging socket lighting  
Fig. 70 Behind the battery charging  
socket cover: charging process indicator.  
In the dark, the charging socket's side lighting  
(white LED) can facilitate orientation in the ve-  
hicle:  
Charging process displays:  
The LED ꢀashes  
●
The vehicle has detected the charging con-  
nector.  
76  
Chargingthehigh-voltagebattery  
●
●
On  
Switch oꢂ the drive system.  
Seek professional assistance.  
If the message is hidden, the warning lamp re-  
mains visible  
.
●
●
The vehicle has been unlocked.  
The audible warning can only be turned oꢂ  
by a qualiꢀed workshop. CUPRA recommends  
that you visit an oꢂicial dealer.  
OR: The charging connector has been un-  
plugged from the charging socket.  
and  
Danger of ꢀre!  
Oꢀ  
The warning lamp lights up red and is dis-  
played along with with a text message on the  
instrument cluster accompanied by a continu-  
ous audible warning.  
WARNING  
●
After unlocking or locking the vehicle, the  
lighting switches oꢂ automatically after a while.  
If there is a risk of ꢀre in the high-voltage  
battery, toxic gases may escape or compo-  
nents may be released from the high voltage  
battery. There is a risk of serious injury, burns  
or lethal electric shocks.  
Charging process indicator lamp  
The high voltage battery temperature is too  
high  
.
During the charging process, the  
displayed on the instrument cluster display.  
lamp is  
If this message is displayed on the instrument  
●
››P›aprkagthee6v5e,hBicelheasvaifoeulyraisnstohoeneavsepnotsosifbalen  
cluster, please note ›››  
below:  
and follow the steps  
White indicator: connector plugged in, no  
charging process active.  
accident or ꢀre.  
●
Stop driving! Stop the vehicle immedi-  
Green indicator: connector plugged in,  
charging process active.  
●
Get out of the vehicle and keep a safe dis-  
ately, taking into account the traꢂic situation.  
tance away from it.  
●
Choose a safe place outdoors, away from  
●
Call the ꢀre department immediately.  
buildings or vehicles, canopies, covered car  
parks or similar places.  
Troubleshooting  
Deep discharge of the high-voltage bat-  
●
Before leaving the vehicle, make sure it is im-  
Fault in the high voltage system  
tery due to prolonged parking time  
mobilised (parking brake, parking lock P).  
The warning lamp lights up red. A message is  
displayed in this regard.  
●
Switch oꢂ the ignition and leave the ignition  
The control lamp lights up red. A message is  
displayed.  
key on the dash panel or in a visible place.  
There is a fault in the high voltage system. The  
high voltage components may be damaged  
●
Exit the vehicle and make sure that there are  
The high-voltage battery can be damaged if,  
for example, the vehicle is not used for a long  
time.  
no other people or animals left inside.  
›››  
.
●
Make sure that you leave the danger zone to-  
It is not possible to charge the high-voltage  
battery.  
gether with all other occupants of the vehicle  
and that everyone remains in an area that is  
protected from traꢂic (e.g. behind the guard  
rail).  
●
Charge the high-voltage battery immedi-  
ately.  
●
The vehicle must be parked in a safe  
place. Park the vehicle outdoors as soon as it is  
possible and safe to do so.  
●
Notify the emergency services.  
77  
High-voltage battery  
●
Check if a fault is displayed on the charging  
High voltage battery discharged  
WARNING  
station or, depending on the equipment, on  
the charging cable protection device.  
The control lamp switches on yellow. A mes-  
sage is displayed.  
High-voltage components, including the bat-  
tery and high-voltage cables, may be live and  
damaged. The high voltage system voltage is  
dangerous and can cause burns, other inju-  
ries and fatal electric shocks.  
If the fault cannot be rectiꢀed, contact a spe-  
cialist workshop immediately.  
●
Charge the high-voltage battery immedi-  
ately.  
The charging cable protection device dis-  
connects  
●
Do not touch the high voltage compo-  
Low state of charge in the high-voltage  
nents!  
battery  
If electrical devices with a separate electrical  
connection, e.g. a cool box, are used in the  
vehicle at the same time, the self-test of the  
protective device may detect a fault.  
The control lamp switches on yellow. A mes-  
sage is displayed showing the remaining range.  
Emergency release of the charging  
connector  
The high-voltage battery charge has reached  
the reserve level.  
●
Please note the order! First connect the  
charging cable to the external power supply  
and then to the charging socket.  
●
Charge the high-voltage battery.  
Range calculation fault  
The charging time varies  
The control lamp switches on yellow. A mes-  
sage is displayed.  
During the direct current (DC) charging proc-  
ess, the charging current is reduced automat-  
ically to preventing the high-voltage battery  
from overheating.  
There is a fault in the range calculation. Con-  
tact a specialised workshop.  
After several fast charging processes in a row,  
the charging time is temporarily extended.  
The charging process is not possible or has  
been paused  
Fig. 72 On the lower right-hand side of  
the luggage compartment trim: cover with  
cutting lines.  
The charging process indicator located next to  
the charging socket lights up red.  
Before visiting a specialist workshop, you can  
try the following solutions:  
●
●
Plug the charging cable back in.  
Check that the charging connector is plug-  
ged in correctly.  
78  

Related Topics

Popular Owner Manuals