2024-2026 Cupra Terramar SUV Driver information User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Driver information for Your Cupra Terramar SUV First Generation (2024-2026)

Driver information
11
Control lamps
Driver information
Control lamps
Control and warning lamps
The warning and control lights can be lit indi-
vidually or in combination and serve as a warn-
ing, to indicate the presence of an anomaly or
to warn of the activation of certain functions.
Some turn on when the ignition is switched on
and must turn o after a certain period of time.
Depending on the model, additional text mes-
sages may be viewed on the instrument panel
display. These may be purely informative or
they may be advising of the need for action.
Warning with priority 1:
●
The red central warning lamp lights up or
ashes, possibly accompanied by additional
audio warnings or symbols. Stop driving!
Danger! Check the faulty function. Seek spe-
cialist assistance as soon as possible.
Warning with priority 2:
●
The yellow central warning lamp lights up
or ashes, possibly accompanied by additional
audio warnings or symbols. Operating faults or
the lack of operating uids can cause damage
to the vehicle or a fault. Check the faulty func-
tion as soon as possible and, if necessary, con-
tact a specialist workshop immediately.
CUPRA recommends visiting an Oicial CUPRA
Service.
Lamps with other colours:
●
Green, blue, white and grey: Information on
other systems.
Depending upon the equipment tted in the
vehicle, instead of a warning lamp, sometimes
a symbol may be displayed on the instrument
panel.
The control lamps that light up on the light
control are explained in chapter ›››page131,
Lights.
WARNING
If the warning lamps and messages are ig-
nored, faults may occur in the vehicle, it may
stall in traic, or accidents and serious inju-
ries may occur.
●
Never ignore warning lamps or text mes-
sages.
●
Stop the vehicle as soon as possible in a
safe place.
Note
If there are several warnings, the corre-
sponding symbols will light up for a few sec-
onds and remain lit until the cause is elimina-
ted.
If when switching on the ignition warnings
are shown about existing faults, it might not
be possible to change the settings or show
the information as described. If the fault
continues, consult a specialised workshop.
CUPRA recommends visiting an Oicial
CUPRA Service.
Sym-
bol
Meaning
Stop driving!
Central warning lamp ›››page25
Fasten your seat belt ›››page47
Electronic parking brake on
›››page226
Deep discharge of the high-voltage
battery ›››page88
12
Driver information
Sym-
bol
Meaning
Stop driving!
Fault in the brake system
›››page189
Stop driving
Brake uid level low ›››page359
Stop driving!
The electromechanical brake servo
is not working ›››page192
Take control of the vehicle and be
ready to brake! ›››page204
Stop driving
Fault in the motor coolant uid sys-
tem ›››page20
Stop driving
Fault in the high-voltage system
coolant uid system ›››page20
Engine oil pressure ›››page364
Engine oil level very low
›››page364
Stop driving!
Steering anomaly ›››page185
Sym-
bol
Meaning
Stop driving!
Fault in the high voltage system
›››page87
Stop driving!
Fault in the electric drive system
›››page174
Stop driving!
12volt battery ›››page369
Stop driving!
48volt battery ›››page371
Collision warning ›››page212
Take control of the steering imme-
diately ›››page220
Emergency Assist active with lane
guidance ›››page221
Emergency Assist active without
lane guidance ›››page221
Central warning lamp ›››page25
Sym-
bol
Meaning
Emergency call restricted
›››page77
Error_ emergency call
›››page77
Fault in the airbag system or the
seat belt tensioners ›››page56
Range calculation failure
›››page88
Front passenger airbag o
›››page56
Front passenger airbag on
›››page56
Please check brake pad
›››page189
Lights up: fault in the electronic sta-
bility control (ESC) ›››page192
Flashing: Electronic stability control
(ESC) or Traction Control (TCS) reg-
ulating ›››page192
TCS switched o manually, ESC in
Sport mode or ESC turned o man-
ually ›››
page191
ESC disconnected ›››page191
ABS fault ›››page192
Driver information
13
Control lamps
Sym-
bol
Meaning
Fault in the electronic parking brake
›››page227
Fault in the electromechanical
brake servo ›››page192
Travel Assist not available
›››page220
Fault in the vehicle's lighting
›››page131
Fault in the emissions control sys-
tem ›››page337
Particulate lter clogged
›››page337
Rear fog light on ›››page131
Fuel tank almost empty
›››page19
Engine oil level ›››page365
Windscreen washer uid level too
low ›››page141
Steering anomaly ›››page185
Sym-
bol
Meaning
Fault in the tyre pressure loss indi-
cator ›››page387
Stop driving!
Low tyre pressure ›››page387
Fault in the electric drive system
›››page174
Petrol engine management fault
›››page337
Electric drive system power limited
›››page175
Electronic engine sound fault
›››page174
Front Assist not available or with
limitations ›››page214
Front Assist deactivated
›››page215
Cruise control fault (GRA)
›››page200
Speed limiter not available
›››page201
Gearbox fault ›››page182,
›››page182
Adaptive cruise control (ACC) not
available ›››page209
Sym-
bol
Meaning
Emergency Assist unavailable
›››page222
Lane Assist not available
›››page217
Limited driver assistance now.
Front sensors without visibility
›››page217
Lane Assist (lane keeping system)
regulating ›››page217
Lane Assist deactivated
›››page217
Drowsiness monitor limited or un-
available ›››page29
Driver attention monitor unavaila-
ble ›››page31
Fault in the driver attention monitor
›››page31
Exit Warning not available
›››page197
Side Assist (lane change assistance
system) not available ›››page197
Road sign recognition limited or not
available ›››page34
Rear Cross Traic Alert not available
›››page197
14
Driver information
Sym-
bol
Meaning
Battery / 12V power supply
›››page369
Battery / 48V power supply
›››page371
Low state of charge of the high volt-
age battery ›››page88
High voltage battery discharged
›››page88
Engine RPM limitation
›››page18
Auto Hold active ›››page228
Turn signals ›››page131
Trailer turn signals ›››page131
Cruise control (GRA) ›››page199
Speed limiter active ›››page200
Lane Assist (lane keeping system)
active. ›››page217
Press the brake pedal ›››page182
Travel Assist active ›››page219
Sym-
bol
Meaning
Adaptive Cruise Control (ACC) reg-
ulating, no vehicle detected ahead
›››page206
Adaptive Cruise Control (ACC) reg-
ulating, vehicle detected ahead
›››page206
Vehicle charging ›››page87
Adjustment due to the road layout
›››page210
Adjustment due to a roundabout
›››page210
Adjustment due to a junction
›››page210
Adjustment due to a speed limit
›››page210
Adjustment due to the end of a
traic jam ›››page210
Adjustment due to a speed limit
›››page210
Main beam on or asher on
›››
page131
Main beam assist active
›››page131
Auto Hold function on
›››page228
Sym-
bol
Meaning
The cruise control system is
switched on, but regulation is not
active ›››page199
The speed limiter is not active
›››page200
Lane Assist not ready to regulate
›››page217
Start-Stop system activated
›››page175
Start-Stop system unavailable
›››page175
Travel Assist active, adaptive cruise
control (ACC) active and adaptive
lane guidance function passive.
›››page219
Hill Descent Control (HDC)
›››page183
Exterior temperature below +4°C
(+39°F) ›››page23
Main beam assist on ›››page134
Take control of the steering
›››page220
Speed warning system partially de-
activated ›››page34
Driver information
15
Instrument cluster
Sym-
bol
Meaning
Front Assist connecting
›››page214
Distance warning ›››page212
Electric mode driving not available
›››page175
Reference to information in
the on-board documentation
›››page25
Service intervals display
›››page26
Instrument cluster
Introduction
After switching the engine on with a 12-volt
battery that is heavily discharged or newly re-
placed, some system settings (such as the
time, the date, the personalised comfort set-
tings and the programming) might be altered
or deleted. Check and correct these settings
once the battery is suiciently charged.
WARNING
Any distraction may lead to an accident, with
the risk of injury.
●
Do not operate the instrument cluster con-
trols when driving.
●
To reduce the risk of accident and injury,
only make adjustments to the instructions
on the instrument cluster display and to the
instructions on the Infotainment system dis-
play when the vehicle is stationary.
16
Driver information
1
2
3
4
5
6
7
Digital Cockpit
Fig.1 Digital Cockpit on the instrument cluster
(classic view).
Fig.2 Hybrid vehicles: Digital Cockpit on the
instrument cluster (classic view).
Control and warning lamps ›››
page11.
Rev counter ›››page18.
Powermeter (hybrid vehicles)
›››page21.
Gear engaged or selector lever position
›››page177.
Screen displays ›››page23.
Speedometer.
Digital speed display.
Information proles ›››page17.
Driver information
17
Instrument cluster
1)
Depending on the version.
The Digital Cockpit is a digital instrument clus-
ter with a high-resolution TFT colour screen. It
has a 4 views accessible using the button
of
the multifunction steering wheel.
By selecting dierent information proles, in-
dications other than the classic circular instru-
ments can be displayed, such as navigation
data, multimedia information or travel data.
The 4 views are:
●
Classic
●
Dynamic
●
Navigation
●
CUPRA
All views will display information on the screen
about audio, phone, travel data, vehicle status,
navigation
1)
and driving aids
1)
.
Information proles
The
/ buttons on the multifunction steer-
ing wheel can be used to browse through the
dierent Digital Cockpit information.
Information on the vehicle status, travel data
and odometer will be displayed on the left side.
On the right side information will be displayed
on: audio, telephone, compass, navigation
manoeuvres and the G-force meter.
Depending on the view in the middle of the
Digital Cockpit information about the following
will be displayed:
●
Classic View and Dynamic View: Initial data,
date, distance travelled and range. Turning the
right thumbwheel on the multifunction steer-
ing wheel: navigation map, driving data (press-
ing switches between the dierent memo-
ries).
●
Navigation View: By pressing the button
on the multifunction steering wheel and then
turning the thumbwheel you can zoom into
or out of the map. If you press the button
again, the map returns to automatic scale.
●
CUPRA view: The revolutions tube is dis-
played in the centre.
Classic and Dynamic View:
The revolutions per minute and speedometer
needles appear in full length if you press and
hold the button on the multifunction steer-
ing wheel, regardless of the menu displayed in
the central area ›››Fig.1 , ›››Fig.2.
Pressing and holding the button again re-
turns the display to the previous view.
Or look in the instrument cluster menu for the
Close option using the right hand thumb-
wheel on the multifunction steering wheel, and
then press .
Information that may be displayed in the
central area of the Digital Cockpit speedom-
eter
●
Audio
●
Telephone
●
Compass
●
Navigation indications (the most recent des-
tinations are displayed by pressing the arrow
on the right of the multifunction steering
wheel)
●
G-force meter.
●
> (close classic view).
Information that may be displayed in the
central area of the Digital Cockpit rev coun-
ter
●
Consumption and average consumption. By
pressing the arrow on the left of the multifunc-
tion steering wheel, you can switch between
the dierent travel data memories.
●
Range (fuel tank level).
●
Lubricating oil and coolant temperature
●
Average speed. By pressing the arrow on the
left of the multifunction steering wheel, you
can switch between the dierent travel data
memories.
18
Driver information
1)
Depending on version.
2)
Only in the CUPRA view on the instrument cluster.
●
Other travel data: km travelled and driving
time. By pressing the arrow on the left of the
multifunction steering wheel, you can switch
between the dierent travel data memories.
●
Assist systems.
●
Engine power and torque.
●
> (close classic view).
CUPRA view
Turning the right hand thumbwheel on the
multi-function steering wheel scrolls through
the following information displayed in the mid-
dle of the rev counter:
●
Speed and gears.
●
Lap timer.
The following information is displayed outside
the rev counter circle:
●
Right-hand area: G-force meter.
●
Left-hand area: engine power and torque.
Rev counter
The rev counter indicates the number of en-
gine revolutions per minute.
Together with the gear-change indicator, use
the rev counter to make sure you are running
your vehicle's engine at a suitable speed.
The beginning of the red zone of the rev coun-
ter indicates the maximum speed in any gear
after running-in and with the engine hot. How-
ever, it is advisable to move the selector lever
to D or lift your foot o the accelerator before
the needle reaches the red zone ›››
.
We recommend that you avoid high revs and
that you follow the recommendations on the
gear-change indicator. See the additional in-
formation in ›››page161, Selecting the op-
timal gear.
Speed limiter
1)
If the indicator light
turns on, the engine will
be automatically limited to the speed shown on
the instrument cluster. This protects the en-
gine components in situations such as a cold
start or against overheating.
The engine speed limiter is released as soon as
the engine reaches normal operating temper-
ature and the driver takes his/her foot o the
accelerator.
If the engine speed limit is caused by an engine
management fault, the indicator lamp also
lights up. Make sure the displayed RPM is not
exceeded (for example, by reducing it). Go im-
mediately to a specialised workshop to have
the fault repaired.
Flashing indicator
1)2)
The ashing indicator warns the driver that the
engine RPM limit has been reached.
The ashing indication is displayed in the up-
per areas of the rev counter by green, yellow
and red areas.
When the RPM approaches the limit, the ash-
ing indicator ashes red. Shift up a gear at the
right time.
NOTICE
●
To prevent damage to the engine, the rev
counter needle should only remain in the red
zone for a short period of time.
●
When the engine is cold, avoid high revs
and heavy acceleration and do not make the
engine work hard.
For the sake of the environment
Changing up a gear early will help you to
save fuel and minimise emissions and engine
noise.
Driver information
19
Instrument cluster
Fuel gauge
Fig.3 Fuel gauge located in dierent
positions depending on the view.
1
Reserve
2
Fuel level
Control lamps
Lights up yellow. Fuel tank almost
empty. The fuel reserve level has been
reached ›››
. Refuel as soon as you
have the opportunity.
The display only works when the ignition is
switched on.
The fuel range is displayed on the instrument
cluster.
You can consult the tank capacity of your vehi-
cle in ›››page411.
WARNING
When driving with low fuel, the vehicle may
stall in traic and cause accidents and severe
injuries.
●
If the fuel tank level is too low, fuel
could reach the engine irregularly, particu-
larly when driving up or down slopes.
●
The steering system and the assistant sys-
tems and brakes do not work when the en-
gine is running irregularly or switches o due
to lack of fuel or an irregular fuel supply.
●
CUPRA recommends always refuelling
when the tank is approximately one quarter
full, to prevent the vehicle from stopping due
to a lack of fuel.
NOTICE
Never run the fuel tank completely dry. An
irregular fuel supply can cause misring and
unburnt fuel could enter the exhaust system.
The catalytic converter or the particulate l-
ter may get damaged!
Note
The small arrow on the fuel gauge next to the
fuel pump symbol points towards the side of
the vehicle with the fuel tank ap.
Battery level indicator
✓ Valid for: hybrid vehicles
Fig.4 Digital instrument cluster: battery
level indicator.
1
Reserve
2
Battery level
The small arrow next to the battery symbol on
the fuel gauge indicates which side of the vehi-
cle the charging cover is on.
NOTICE
●
Never drive with the tank completely
empty. Under certain circumstances, the en-
ergy stored in the high-voltage battery may
not be suicient to reach the nearest service
station.
●
When the outside temperature is very low,
and therefore the high-voltage battery is
very cold, you may have diiculty starting the
internal combustion engine and the range in
electric driving mode may be reduced.
20
Driver information
Coolant temperature indicator.
The coolant temperature view can be selected
in the corresponding menu ›››
page16.
Control and warning lamps
Fault in the engine coolant system
The LED ashes red.
Engine coolant
The lamp lights up red.
The motor coolant temperature is too
high or the motor coolant level is too
low.
●
Stop driving! Stop the vehicle at the rst
opportunity and in a safe place.
●
Switch o the engine and let it cool down.
●
Check the coolant level in the coolant ex-
pansion tank ›››page356.
If the warning lamp does not go out even
though the motor coolant level is correct, do
not continue to drive or leave the engine run-
ning. Seek specialist assistance.
Control and warning lamps (valid for hybrid
vehicles)
together
with
Fault in the high-voltage cool-
ing circuit
The warning lamps ash red.
Engine coolant
The lamp lights up red.
Engine or high-voltage system
coolant level too low, engine or
high-voltage system coolant tem-
perature too high.
●
Stop driving! Stop the vehicle at the rst
opportunity and in a safe place.
●
Switch o the engine and let it cool down.
●
Check the coolant level in the coolant ex-
pansion tank ›››page356.
●
Check the coolant level in the high-voltage
cooling circuit ›››page356. If the level is too
low DO NOT add coolant. Seek specialist as-
sistance immediately.
If the warning lamp does not go out even
though the motor coolant level is correct, do
not continue to drive or leave the engine run-
ning. Seek specialist assistance.
NOTICE
●
To ensure a long useful life for the engine,
avoid high revs, driving at high speed and
making the engine work hard for approxi-
mately the rst 15 minutes when the engine
is cold. The engine's warming-up phase also
depends on the outside temperature. If nec-
essary, use the engine oil temperature as a
guide ›››page24.
●
Additional lights and other accessories in
front of the air inlet reduce the cooling eect
of the coolant. At high outside temperatures
and high engine loads, there is a risk of the
engine overheating.
●
The front spoiler also ensures proper distri-
bution of the cooling air when the vehicle
is moving. If the spoiler is damaged this can
reduce the cooling eect, which could cause
the engine to overheat. Seek specialist assis-
tance.
Driver information
21
Instrument cluster
A
B
C
1
2
3
Power meter
✓ Valid for: hybrid vehicles
Fig.5 Digital instrument cluster: Power
meter
The following displays can be seen on the
Power meter: ›››
Fig.5.
Green zone (Charge). The vehicle recov-
ers electrical energy.
Blue zone (Power %). Driving in Electric
Mode. Indicates the percentage of power
used and the maximum amount of power
currently available.
Revolutions per minute of the combustion
engine when in operation.
The power meter shows the usage level of the
electric drive. The power meter bar shows the
current usage level.
A ner coloured border indicates how much
the propulsion can currently be used. Depend-
ing on the selected driving program and the
current availability of electrical power, the
boundaries of the dierent colours can vary.
Availability of Boost on screen
When the engine is started, the “READY” warn-
ing light goes out and the instrument cluster
displays Boost availability indications with in-
formation about the additional power available
at that time.
Fig.6 In the digital instrument cluster: Boost
availability display
Additional power available.
Additional power not available.
Boost additional power activated.
If rapid acceleration is requested (e.g. by Kick-
Down) the Boost function will be activated and
the vehicle will drive for a short period of time
with maximum power from the electric motor
and combustion engine. This is indicated by
the area below the RPM indicator turning blue.
Note
The Boost function consumes a large
amount of energy and is therefore only avail-
able for a short period of time.
WARNING
When the electrical system has a reduced
performance capability, it can cause a
change in the vehicle’s handling, such as
a dierent acceleration response. This can
cause accidents and serious or even fatal in-
juries.
●
Always adapt your speed and driving style
to suit the visibility, weather, road and traic
conditions, as well as the charge level of the
high-voltage battery.
●
Make sure that the high-voltage battery is
suiciently charged.
22
Driver information
Head-up-Display (HUD)
Fig.7 In the driver’s eld of view: Proximity
HUD
1
.
The Head-up-Display (HUD) projects certain
information or warnings from assistance sys-
tems or the infotainment system into the driv-
er’s eld of view.
Display areas
Explanations of the areas displayed on the
Head-up-Display ›››
Fig.7:
●
Proximity HUD. Information on speed, navi-
gation and driver assistant systems is displayed
on the proximity HUD
1
.
The amount and content of the information
displayed may vary depending on the equip-
ment.
Switching the Head-up-Display on and o
The Head-up-Display can be switched on and
o in the infotainment system’s vehicle set-
tings menu.
●
Press the Vehicle function button.
●
In Vehicle, select the Interior view and press
the Head-up-Display function button.
●
Switch the Head-up-Display on or o as de-
sired. Activated functions are highlighted in
colour.
Height setting
To adapt the vertical position of the image to
your individual seating position, the Head-up-
Display can be set in the infotainment system’s
vehicle settings menu.
1. Sit comfortably on the seat.
2. In the vehicle settings of the infotainment
system you can also adjust the rotation of
the proximity area.
Infotainment system settings
Further settings of the Head-up-Display can
be changed in the vehicle settings menu of the
infotainment system.
The following settings can also be adjusted:
In the Head-up-Display settings submenu:
●
Adjustment of the light intensity of Head-up-
Display indications. The intensity is automat-
ically reduced as the ambient brightness de-
creases. The basic brightness is adjusted via
the Head-up Display's settings menu.
●
Selection of the indications to be shown on
the Head-up-Display, e.g. driver assistant sys-
tem indications.
●
There is an alternative combination of col-
ours for the Head-up-Display for adverse
weather conditions, e.g. if it snows.
Note
●
Some indications, such as warnings, cannot
be hidden.
●
For optimal viewing of the display, correctly
adjust the seat and the height of the Head-
up-Display.
●
Light falling on it can cause reections.
Wearing sunglasses with polarizing lters
may prevent you from seeing the indications
properly.
●
Only clean the Head-up-Display with a soft
cloth and a mild cleaning product. Microbre
cloths can scratch the Head-up-Display.
Driver information
23
Instrument cluster
Status display
Possible indications on the instrument clus-
ter display
The instrument cluster can display a variety of
information, superimposed according to the
vehicle's equipment:
●
Doors, bonnet and rear lid open
●
Warning and information messages
●
Odometer
●
Time ›››page25
●
Indications of the radio and navigation sys-
tem
●
Phone indications
●
Outside temperature
●
Compass indication
●
Selector lever positions
●
Gear-change recommendation
●
Combined range (hybrid vehicles)
●
Display of travel data (multifunction display)
and menus for dierent settings ›››page24
●
Service interval indicator ›››page26
●
Speed warning
●
Speed warning for winter tyres
●
Start-Stop system status display
›››page175
●
Signs detected by the road signs detection
system and warning that the speed limit has
been exceeded
●
Indication of active cylinder management
status (ACT®) ›››page161
●
Low consumption driving
●
Driver assist systems display
Doors, bonnet and rear lid open
When the vehicle is unlocked and while driv-
ing, the instrument cluster display shows if any
of the doors, the bonnet or rear lid are opened
and. In some cases this is also indicated by an
audible warning.
Selector lever positions
The current position of the selector lever is
shown on the side of the control and on the
instrument cluster display. When the control is
in the D/S position or in the Tiptronic position,
in some cases, the gear engaged in each case
is shown on the instrument cluster display .
Outside temperature indicator
If the outside temperature is lower than ap-
proximately +4°C (+39°F), the “ice crystal sym-
bol”
also lights up on the outside tempera-
ture indicator. This symbol remains lit until the
outside temperature exceeds +6°C (+43°F)
››› .
In the following situations, the displayed out-
side temperature may be higher than the ac-
tual temperature due to the heat emitted by
the motor:
●
When the vehicle is stationary
●
When driving very slowly
Gear-change recommendation
While driving, the instrument cluster of certain
vehicles may indicate a gear recommendation
for saving fuel ›››page161.
Odometer
The odometer registers the total distance trav-
elled by the car.
Speed warning for winter tyres
If the maximum set speed is exceeded, this is
displayed on the instrument cluster display.
The speed warning can be set in the infotain-
ment system ›››page39.
Low consumption driving
Depending on the equipment, when driving,
the display appears on the instrument clus-
ter when the vehicle is in low consumption sta-
tus due to active cylinder management (ACT®)
›››
page161.
24
Driver information
–
–
–
–
–
–
WARNING
Even when the outside temperature is higher
than freezing, some roads and bridges could
be frozen.
●
The “ice crystal symbol” indicates that
there may be a risk of freezing.
●
At outside temperatures above +4°C
(+39°F), there may be ice even when the “ice
crystal symbol” is not on.
●
The outside temperature sensor takes a
guideline measurement.
Note
●
There are dierent instrument clusters and
therefore the versions and instructions on
the display may vary. In the case of displays
without warning or information texts, faults
are indicated exclusively by the control warn-
ing lamps.
●
Some indications on the instrument cluster
display may be concealed by a sudden event,
e.g. an incoming call.
●
Depending on the equipment, some set-
tings and instructions can be changed or dis-
played on the infotainment system as well.
●
If there are several warnings at the same
time, the symbols will be displayed one after
the other for a few seconds. The symbols will
stay on until you remove the cause.
●
If warnings are shown about existing faults
when the ignition is switched on, it might not
be possible to change the settings or display
the information as described. In this case, go
to a specialised workshop and request a re-
pair.
Driving data display
The driving data display shows a range of driv-
ing data and consumption values.
Change from one display to another
●
Turn the right thumbwheel of the multifunc-
tion steering wheel ›››page35.
Changing memory
●
Depending on the view, select Driving data
and press the left arrow or the button on the
multifunction steering wheel.
Since start: The memory is deleted if the
journey is interrupted for more than 2
hours.
Since refuel: Display and storage of the
journey data and the consumption values
collected. When refuelling, the memory is
deleted.
Long-term: This memory contains travel
data up to a maximum of 19hours and
59minutes or 99hours and 59minutes, or
up to a maximum of 1999.9 km or 9999.9
km. When one of these values is exceeded
(varies depending on the version of the in-
strument cluster), the memory is deleted.
Delete journey data presets
●
Select the memory you want to delete - ei-
ther “Since start” or “Long-term”. The “Since
refuelling” memory is only cleared when refu-
elling.
●
Press and hold the button on the multi-
function steering wheel for approximately 2
seconds.
Select the instructions
On the instrument cluster, it is selected man-
ually using the button on the multifunction
steering wheel. To access the contents of the
tube, rotate the right hand thumbwheel up/
down.
Current consumption: The current fuel
consumption display operates throughout
the journey, in litres/100 km; and with the
engine running and the vehicle stopped, in
litres/hour.
Average consumption: The average fuel
consumption is displayed after driving for
approximately 300metres.
Travelling time: This indicates the hours
(h) and minutes (min) since the ignition
was switched on.
Driver information
25
Instrument cluster
–
–
–
–
Range: Approximate distance in km that
can still be travelled if the same driving
style is maintained.
Distance travelled: Distance covered in
km (miles) after switching on the ignition.
Average speed: The average speed will
be shown after driving for approximately
100metres.
Boost/Torque: Indicates the power and
torque of the combustion engine (does
not indicate electric mode).
Oil temperature display
The engine reaches its operating temperature
when, under normal driving conditions, the
oil temperature is between 80°C (176°F) and
120°C (248°F). If a great eort is required from
the engine and the outside temperature is
high, the engine oil temperature may increase.
This is not a problem as long as the warning
lamps
or ›››page364 do not appear
on the display.
Warning and information messages
The system runs a check on certain com-
ponents and functions when the ignition is
switched on and while the vehicle is moving.
Faults are displayed on the instrument clus-
ter display as red and yellow warning symbols
›››
page11 accompanied by messages and,
depending on the case, even an audible warn-
ing. The representation of the messages and
symbols may vary depending on the version of
the instrument cluster.
Existing faults can also be checked man-
ually. To do this, open the Vehicle status
›››
page34 menu.
Priority 1 warning (in red)
The symbol lights up or ashes (sometimes
accompanied by audible warnings). Stop
driving! Danger! Check the fault and eliminate
the cause. If necessary, seek professional as-
sistance.
Priority 2 warning (in yellow)
The symbol lights up or ashes (sometimes
accompanied by audible warnings). Operating
faults or the lack of operating uids can cause
damage to the vehicle or a fault. Check the
faulty function as soon as possible. If neces-
sary, seek professional assistance.
Reference to information in the own-
er's manual
Further information on any warnings can be
found in the owner's manual.
Information message
It provides information about processes in the
vehicle.
Accessing warnings and information
Existing faults can also be checked in the info-
tainment system:
●
Press > Vehicle > Vehicle status
›››page41.
Date and time
Setting the time on the infotainment system
●
Press > Settings ›››page36.
●
Select the menu option Date and time.
●
OR set the date and time in the instrument
cluster’s Service menu.
Service Menu
In the Service menu various settings can be
adjusted depending on the features.
Open the Service menu
●
While in Classic View, go to the circle on the
left and select the odometer, then press the
button on the multifunction steering wheel
for around 5 seconds and then release it.
●
Next, the Conguration list menu is dis-
played, where you can choose between the
Service menu or View selection from where
the instrument cluster views can be switched
on and o.
26
Driver information
Restart the service interval indicator
Select the Service menu and follow the in-
structions on the instrument cluster display.
Reset the oil service
Select the Reset Oil service menu and follow
the instructions on the instrument cluster dis-
play.
Identifying letters on engine (LDM)
Select the menu Engine code. The identifying
letters of the engine will be shown on the in-
strument cluster display.
Next Service
This species when the next workshop inspec-
tion is scheduled.
Setting the date and time
Select the Service menu and follow the in-
structions on the instrument cluster display.
Service intervals
The service interval indicator appears on the
instrument cluster display and in the infotain-
ment system.
There are dierent versions of instrument
clusters and infotainment systems, so the ver-
sions and instructions on the screens may vary.
CUPRA distinguishes between services with
engine oil change (e.g. Oil change service)
and services without engine oil change (e.g.
Inspection).
In vehicles with Services established by time
or mileage, the service intervals are already
pre-dened.
In vehicles with LongLife Service, the inter-
vals are determined individually. Thanks to
technological progress, maintenance work has
been greatly reduced. The oil only needs to
be changed when the vehicle requires it. To
calculate this change (max. 2 years), the vehi-
cle's usage conditions and individual driving
styles are considered. The advance warning
rst appears 20 days before the date estab-
lished for the corresponding service. The kilo-
metres (miles) remaining until the next service
are always rounded up to the nearest 100 km
(miles) and the time is given in complete days.
The current service message cannot be viewed
until 500 km after the last service. Prior to this,
only lines are visible on the display.
Inspection reminder
If a service or an inspection has to be carried
out soon, a service reminder will be displayed
when the ignition is switched on.
The gure shows the kilometres that can still
be travelled or the time until the next service.
Service due
When the time for a service or an inspec-
tion comes, an audible warning will be emitted
when the ignition is switched on and the xed
key symbol
may appear on the instrument
cluster for a few seconds, along with one of the
following messages:
●
Service now!
●
Please have your vehicle inspected
●
Oil change service due!
●
Oil change service and inspection due!
Consult a service notication
With the ignition switched on, the engine o
and the vehicle at a standstill, the current serv-
ice notication can be read:
Check the date of the current service on the
infotainment system:
●
Press the function button Vehicle > Vehi-
cle status > Service.
Checking the date on the digital instrument
cluster:
●
The date of the service can only be read
through the Service ›››page25 menu.
Resetting the service interval indicator
If the service was not carried out by a special-
ised CUPRA dealer or any dealer in the SEAT
network, the display can be reset as follows:
Driver information
27
Drowsiness monitor
●
The service interval indicator can only be
reset through the Service ›››page25 menu.
Do not restart the indicator between the serv-
ice intervals, otherwise the information dis-
played will be incorrect.
If the oil change service is reset manually, the
service interval indicator changes to a xed
service interval, also in vehicles with Flexible
oil change service.
Note
●
The service message disappears after a few
seconds, when the engine is started or when
the
button is pressed on the multifunction
steering wheel.
●
In vehicles with the LongLife system in
which the battery has been disconnected for
a long period of time, it is not possible to cal-
culate the date of the next service. Therefore
the service interval indicator may not be cor-
rect. In this case, bear in mind the maximum
permitted service intervals ›››
page391.
●
If you reset the display manually, the next
service interval will be indicated as in vehicles
with xed service intervals. For this reason we
recommend that the service interval indica-
tor be reset by an authorised dealer.
Drowsiness monitor
Introduction
Fig.8 On the instrument cluster display:
Drowsiness monitor symbol.
The drowsiness monitor informs the driver
whether his or her driving behaviour is indi-
cative of fatigue.
The drowsiness monitor determines the driv-
er's driving behaviour and uses this information
to assess driver fatigue. If the system detects
that the driver is tired, it indicates this visually
on the instrument cluster display by means of
a control or warning lamp in combination with
a supplementary text message. It also issues
an audible warning ›››
page28. The text
message on the instrument cluster display is
displayed for 4 to 6 seconds.
Operating conditions
The drowsiness monitor will only display warn-
ings at speeds above 70km/h.
WARNING
The drowsiness monitor is no substitute for
the driver's attention and only works within
the limits of the system. Therefore, the
drowsiness monitor may not detect that the
driver is tired in all situations and may not
give a warning or may give a delayed or unin-
tended warning. There is a risk of accidents
and serious or even fatal injuries.
●
Always pay proper attention and do not rely
solely on the system. The driver is responsi-
ble for his or her tness to drive at all times.
●
Note the limits of the system
›››page27.
●
Never drive a vehicle when you are tired.
●
During long journeys, take regular and suf-
cient breaks.
●
Follow the information on the instrument
cluster display and respond as prompted
›››page28.
System limits aecting the drowsi-
ness monitor
The drowsiness monitor has system-related
limitations. The following conditions may limit
the drowsiness monitor's operation, or prevent
it from operating at all:
●
Speeds below 60 km/h.
●
Speeds over 130 km/h.
●
Roads with many curves.
28
Driver information
●
Roads in poor condition.
●
Adverse weather conditions.
●
Roadworks.
●
Sporty driving style.
●
Towing a heavy or very long trailer
›››page322.
●
The driver is distracted.
Note
The drowsiness monitor has been developed
for use only when driving on motorways and
main roads in good condition.
Restarting the drowsiness monitor
The drowsiness monitor restarts in the follow-
ing situations:
●
If the ignition is switched o.
●
The driver's seat belt is unbuckled and the
driver's door is open.
●
The vehicle has been stopped for more than
30 minutes.
Driving with the drowsiness moni-
tor
Connection and disconnection
Depending on the country, the drowsiness
monitor is activated whenever the vehicle's
drive system is activated.
If desired, you can switch o the drowsiness
monitor manually in the infotainment system:
1. Open the Assistance systems menu.
2. Switch the drowsiness monitor on or
o in the corresponding submenu
›››
page39..
Sensitivity adjustment
You can manually adjust the sensitivity of the
drowsiness monitor and therefore inuence
how quickly the system reacts to your driving
behaviour.
In the infotainment system:
1. Open the Assistance systems menu.
2. Open the Drowsiness monitor.
3. Select the sensitivity in the Sensitivity sub-
menu ›››page39.
Concealing messages via the multi-function
steering wheel
1. Press the button on the multifunction
steering wheel.
Drowsiness monitor warning levels
If the system detects that the driver is tired,
it indicates this visually on the instrument clus-
ter display by means of a control or warning
lamp in combination with a supplementary text
message and an audible warning. The warning
is issued at three levels.
Drowsiness monitor warning - Level 1
The system has detected that the driver is
becoming tired. An audible signal sounds.
A white control lamp and a text message
are shown on the instrument cluster dis-
play. Consider taking a break.
Drowsiness monitor warning - Level 2
The system has detected that the driver
is becoming increasingly tired. An audi-
ble signal sounds. A red warning lamp is
shown on the instrument cluster display
together with a text message. Consider
taking a break soon.
Drowsiness monitor warning - Level 3
Serious risk identied. An audible signal
sounds. A red warning lamp is shown on
the instrument cluster display together
with a text message. Serious traic risk.
Stop driving as soon as possible and pro-
ceed urgently to the nearest place where
you can take a break.
Time-related information
The drowsiness monitor detects that the
driver has been driving for 4.5 hours with-
out a break and without any recognised
fatigue. A white control lamp and a text
message are shown on the instrument
cluster display. Consider taking a break.
Driver information
29
Driver attention monitor
Troubleshooting
Availability of the drowsiness monitor is
restricted
An audible signal sounds. A yellow control light
appears along with a text message on the in-
strument cluster screen. The availability of the
drowsiness monitor is restricted.
●
Fault or malfunction. Deactivate and reacti-
vate the vehicle drive system.
●
If the problem persists, visit a duly qualied
workshop. CUPRA recommends that you visit
an oicial dealer.
The drowsiness monitor is not avail-
able
An audible signal sounds. A yellow control lamp
appears in combination with the yellow centre
lamp. A text message is also shown on the
instrument cluster display and in the vehicle
status menu.
●
Fault or malfunction. Deactivate and reac-
tivate the vehicle drive system. Check the
drowsiness monitor settings in the infotain-
ment system ›››page39.
●
The system limits have been exceeded.
●
If the problem persists, visit a duly qualied
workshop. CUPRA recommends that you visit
an oicial dealer.
Driver attention monitor
Introduction
Fig.9 On the instrument cluster display:
Driver attention monitor symbol.
The driver attention monitor informs the
driver whether his or her driving behaviour
is indicative of a lack of attention, based on
where they are looking and the vehicle's op-
erating inputs.
The driver attention monitor assesses the ve-
hicle's operating inputs to determine whether
the driver is distracted. In addition, an interior
camera tted to the rear view mirror continu-
ously monitor’s the driver’s state and actions,
as well as where they are looking.
If the system detects that the driver is distrac-
ted, it indicates this on the instrument cluster
display by a control or warning lamp in com-
bination with a supplementary text message.
Depending on the conguration, it also emits
an audible warning ›››
page30. The text
message on the instrument cluster display is
displayed for 4 to 6 seconds.
Operating conditions
Driving behaviour is only assessed when the
speed is higher than 20 km/h.
WARNING
The driver attention monitor cannot be a
substitute for the driver's attention and only
works within the limits of the system. There-
fore, the driver attention monitor may not be
able to detect whether the driver is paying
attention in all situations and may not react
or may react with a delay or in an unwanted
manner. There is a risk of accidents and seri-
ous or even fatal injuries.
●
Always pay proper attention and do not rely
solely on the system. The driver is responsi-
ble for his or her tness to drive at all times.
●
Note the limits of the system
›››page30.
●
Avoid distractions while driving.
●
Adjust the vehicle's personal settings be-
fore starting the journey.
●
Follow the information on the instrument
cluster display and respond as prompted
›››
page30.
30
Driver information
Note
In the event of a fault, have the system
checked by a qualied workshop. CUPRA
recommends that you visit an oicial dealer.
System limits aecting the driver
attention monitor
The driver attention monitor has system rela-
ted limitations. The following conditions may
limit the operation of the driver attention mon-
itor or prevent it from operating at all:
●
Speeds below 20 km/h.
●
Severe driver distraction due to external in-
uences such as traic.
●
Severe driver distraction due to actions not
related to the vehicle (for example, using a
mobile device).
●
Insuicient facial recognition.
●
Complex driving situations requiring rapid
eye movement (junctions, merging onto mo-
torways, etc.)
●
Restrictions to the view of the interior cam-
era (on the rear view mirror) towards the driver
- particularly the driver’s eyes and head. This
can be due to darkening caused by peaked
caps, scarves, glasses (particularly glasses that
block IR rays) or the sun visor.
●
If the interior camera on the rear view mirror
is dazzled, e.g. by sunlight.
●
If the rear view mirror is incorrectly adjusted.
●
If the interior rear view mirror glass is fogged,
dirty or damaged.
●
If the driver is in an unsuitable sitting posi-
tion.
●
If the driver has physical limitations (e.g. eye
movement disorders).
Driving with the driver attention
monitor
Connection and disconnection
You can switch the driver attention monitor on
and o manually.
In the infotainment system:
1. Open the Assistance systems menu.
2. Switch the driver attention monitor on
or o in the corresponding submenu
›››
page39.
3. OR: Via the quick access menu using the
scroll bar ›››page36.
Note
Depending on the country, the function
is always switched on when the ignition is
switched on.
Concealing messages via the multi-function
steering wheel
1. Press the
button on the multifunction
steering wheel.
Driver attention monitor warning
levels
If the system detects that the driver is distrac-
ted, it indicates this on the instrument cluster
display by a control or warning lamp in com-
bination with a supplementary text message.
Depending on the conguration, it also emits
an audible warning.
If distraction is detected through vehicle oper-
ation inputs, the warning is issued at three lev-
els. If distraction is detected via interior camera
recognition, the warning is issued directly at
Phase 2.
Driver attention monitor warning - Stage 1.
Distraction detected.
Depending on the conguration, an au-
dible warning may be issued. A white
control lamp and a text message are
shown on the instrument cluster display.
Stop making operating inputs and pay at-
tention to the traic.
Driver attention monitor warning - Stage 2.
Risk detected.
Depending on the conguration, an au-
dible warning may be issued. A red warn-
ing lamp is shown on the instrument clus-
ter display together with a text message.
Stop making operating inputs and pay at-
tention to the traic.
Driver information
31
Road signs detection system
1)
Not available in all markets.
Driver attention monitor warning - Stage 3.
Serious risk identied.
An audible signal sounds. A red warning
lamp is shown on the instrument cluster
display together with a text message. Seri-
ous traic risk. Stop making operating in-
puts immediately and pay attention to the
traic.
Troubleshooting
The availability of the driver attention
monitor is restricted
An audible warning is issued. A yellow control
light appears along with a text message on the
instrument cluster display. The availability of
the driver attention monitor is restricted.
●
Fault or malfunction. Deactivate and reacti-
vate the vehicle drive system.
●
If the problem persists, visit a duly qualied
workshop. CUPRA recommends that you visit
an oicial dealer.
The driver attention monitor is
unavailable
An audible warning is issued. The yellow warn-
ing lamp lights up in the instrument cluster in
combination with the central yellow lamp. A
text message is also shown on the instrument
cluster screen and in the vehicle status menu.
●
Check the causes and corrective measures
described in the information in the driver at-
tention monitor ›››page39.
●
Fault or malfunction. Deactivate and reacti-
vate the vehicle drive system. Check the set-
tings of the driver attention monitor in the in-
fotainment system ›››page39.
●
The system limits have been exceeded.
●
If the problem persists, visit a duly qualied
workshop. CUPRA recommends that you visit
an oicial dealer.
Road signs detection sys-
tem
Introduction
The dynamic road sign display system records
standard traic signs by means of a camera
located in the upper central area of the wind-
screen, housed in the compartment at the
base of the interior mirror, and reports any
speed restrictions, overtaking prohibitions and
warning signs that it recognises
1)
.
Within its limitations, the system also displays
a additional sign to indicate aspects such as
temporary prohibitions. Even on routes with-
out signs, the system can, if necessary, display
the applicable speed limits.
Road sign recognition does not work in all
countries. Keep this in mind when travelling
abroad.
The dynamic road sign display system is activa-
ted whenever the ignition is switched on.
The additional signs are displayed on the
Head-up-Display as generic additional signs.
Shown on the display
In Germany, on motorways and normal roads
for vehicles, besides speed limits and overtak-
ing provisions the system also displays end of
restriction signs. In all other countries the cur-
rently valid speed limit is displayed instead.
The road signs detected by the system are dis-
played on the instrument cluster display and,
depending on the navigation system tted in
the vehicle, in the infotainment system as well .
Depending on the equipment, an indication is
also displayed on the Head-up-Display.
Display of road signs
After checking and evaluating the information
from the camera, the infotainment system and
actual vehicle data, the system displays up to
two current road signs, and an additional sign:
●
First: The sign that is currently valid for the
driver is displayed on the left hand side of the
screen, e.g. a prohibition of driving at over
130km/h (80mph).
32
Driver information
●
Second: Another road sign, such as a warn-
ing sign, can be displayed in second place.
●
Additional sign: If an additional sign is de-
tected, e.g. for temporary limits, it is shown be-
low the valid road sign.
The valid road sign is displayed on the Head-
up-Display by the generic additional sign.
No entry sign
The road sign recognition system gives a warn-
ing on the instrument cluster when a no entry
sign is passed on a one-way road or an en-
trance to a motorway or highway.
WARNING
The technology in the road sign detection
system cannot change the limits imposed by
the laws of physics and only works within the
system's limits. The increased convenience
provided by the dynamic road sign display
system should not lead you to take any risks.
The system is not a replacement for driver
awareness.
●
Adapt your speed and driving style to
suit visibility, weather, road and traic condi-
tions.
●
Poor visibility, darkness, snow, rain and fog
may result in the system not displaying road
signs, or not displaying them correctly.
●
If the camera’s eld of view is dirty, covered
or damaged, the operation of the system may
be aected.
WARNING
The driving recommendations and traic in-
dications shown on the road sign detection
system may dier from the actual current
traic situation.
●
The system cannot recognise or display all
road signs correctly.
●
Road signs and traic regulations have pri-
ority over the recommendations and displays
provided by the system.
Limited operation
The road sign detection system has certain
limitations. The following cases may cause the
system to function in a limited way or not at all:
●
Poor visibility, e.g. in snow, rain, fog or in-
tense mist.
●
Dazzling, e.g. caused by head-on traic or by
the sun.
●
Driving at high speed.
●
If the camera is covered or dirty.
●
If the road signs are partially or totally ob-
structed, e.g. by trees, snow, dirt or other vehi-
cles.
●
Non-compliant road signs.
●
Damaged or bent road signs.
●
Variable message signs on signalling gantries
(variable indication of road signs by LEDs or
other lighting units).
●
If outdated maps are used in the navigation
system.
●
Adhesives aixed to vehicles that depict road
signs, e.g. speed limits on lorries.
Driving with the speed warning
function
Operating conditions
The speed warning function gives warnings at
speeds above 20 km/h.
Connection and disconnection
Depending on the country, the speed warning
function is always activated when the ignition is
switched on.
If desired, you can deactivate the speed warn-
ing manually in the infotainment system:
1. Open the Assistance systems menu.
2. Switch the speed warning on or o in the
corresponding submenu.
OR: from the multifunction steering wheel:
1. Open the assistants menu by pressing but-
ton
.
2. Select and switch o the Speed warning.
Driver information
33
Road signs detection system
Activating and deactivating the audible
warning
In the infotainment system:
1. Open the Assistance systems menu.
2. Open the Speed Warning.
3. Activate or deactivate the audible warn-
ing under the corresponding option
›››page39.
Note
The audible warning is activated whenever
the ignition is switched on.
Adjusting the warning thresholds
You can manually adjust the warning thresh-
olds of the speed warning function.
In the infotainment system:
1. Open the Assistance systems menu.
2. Open the Speed Warning.
3. To select the level of the warning thresh-
olds, tap in the Overtaking warning
›››page39 menu option.
Note
When the vehicle's ignition is switched on,
the warning thresholds for the speed warning
are always reset to the default value.
Activation and deactivation of the speed
change warning tone
The speed change warning tone provides the
driver with audible information about a change
in the speed limits. If desired, you can manually
switch o the change tone.
In the infotainment system:
1. Open the Assistance systems menu.
2. Open the Speed Warning.
3. Activate or deactivate the change
tone under the corresponding option
›››
page39.
Concealing fault messages via the multi-
function steering wheel
1. Press the button on the multifunction
steering wheel.
Trailer mode
For vehicles with a factory-installed towbar and
a trailer with electrical connection to the vehi-
cle, the recognition of traic signs that may
apply to the vehicle when towing a trailer, for
example applicable speed limits and no over-
taking signs, can be activated or deactivated in
the vehicle settings menu in the infotainment
system.
In trailer mode, the recognition of valid speed
limits can be adjusted to suit the type of trailer
and country-specic legal requirements.
In the infotainment system:
1. Open the Assistance systems menu.
2. Open Trailer detection.
3. To adapt the warning threshold to the
trailer mode, tap on in the Overtaking
warning menu option.
Speed warning function warning
levels
If the system detects that the speed limit has
been exceeded, it will indicate this visually on
the instrument cluster display by ashing the
speed limit detected by the system and, de-
pending on the conguration, will also issue
an audible warning. A warning is issued at two
levels.
Fig.10 On the instrument cluster display:
violation of the detected speed limit
(illustration).
34
Driver information
Speed warning - Level 1
Speed limit violation detected. The speed
limit detected by the system ashes continu-
ously on the instrument cluster and, depend-
ing on the equipment, on the front display
›››Fig.10.
Speed warning - Level 2
Progressive violation of the speed limit has
been detected.
An audible signal sounds. The speed limit de-
tected by the system ashes continuously on
the instrument cluster and, depending on the
equipment, on the front display ›››Fig.10.
Note
●
The second warning level is activated if the
speed remains above the limit.
●
The second warning level is cancelled again
when the driver actively reduces the speed.
Troubleshooting
Advanced road sign recognition is
not available
A yellow control lamp appears on the instru-
ment cluster display in combination with the
central yellow lamp. A text message is also
shown on the instrument cluster display and
in the vehicle status menu.
Road sign detection system messages:
●
“Dynamic road sign assist: please clean the
windscreen.”
–
The windscreen is dirty in the area of the
camera or the camera view is impaired by
weather conditions. Clean the windscreen
›››page394.
–
The camera's view is impaired by added
parts or stickers. Keep the area around the
camera clear ›››page194.
–
The camera has been moved or damaged,
for example due to damage to the wind-
screen. Check whether the damage can be
seen.
●
“Error: dynamic road sign assist”
–
There is a fault in the system. Have the
system checked by a specialised workshop.
●
“Speed warning is currently unavailable”
–
The speed warning function of the road
sign detection system is faulty. If the problem
persists, have the system checked by a speci-
alised workshop.
●
“Dynamic road sign assist currently restric-
ted”
–
The navigation system is not transmitting
data. Check if the navigation system has up-
dated maps.
–
OR: the vehicle is in a region not included
on the navigation system's map.
If the problem persists, have the system
checked by a specialised workshop.
Outside the operating region for advanced
road signs recognition
A message appears on the instrument cluster
display with the following text “Road sign as-
sist: outside the usage area”.
●
No data available for this region. The ad-
vanced road signs recognition system is not
supported in the country you are currently
driving in.
Speed warning system partially deacti-
vated
A white control lamp is shown on the instru-
ment cluster display. The default conguration
of the speed warning has been changed:
●
Check whether the speed warning is
switched o ›››page32.
●
Check if the audible warning is activated
›››page32.
●
Check if the default warning threshold has
been changed ›››page32.
Instrument cluster opera-
tion
Introduction
With the ignition switched on, it is possible to
read the dierent functions of the display by
scrolling through the menus.
Driver information
35
Instrument cluster operation
In vehicles with multifunction steering wheel,
the multifunction display can only be operated
with the steering wheel buttons.
Some menu options can only be read when
the vehicle is at a standstill.
Instrument panel menus
The number of menus and information items
available will depend on the vehicle’s electron-
ics and features.
●
Vehicle status ›››page25.
●
Driving data ›››page24.
●
Assist systems.
–
Front Assist On/O ›››page211
–
ACC (only display) ›››page204
–
Lane Assist On/O ›››page215
–
Travel Assist ›››page218
–
Side Assist On/O ›››page222
–
Speed warning On/O ›››page32
●
Navigation.
●
Audio.
●
Telephone.
WARNING
Distracting the driver in any way can lead to
an accident and cause injuries.
●
Never use the menus on the instrument
panel display while the vehicle is in motion.
NOTICE
After charging or changing the 12-volt bat-
tery, check the system settings. If the power
supply is interrupted, the system settings
might be incorrect or deleted.
Operation using the multifunction
steering wheel
Fig.11 Right side of multifunction
steering wheel: buttons to the menus and
informative indications on the instrument
panel (depending on the version).
As long as a priority 1 ›››
page25 warning
is active, it will not be possible to access any
menu. Some warnings can be conrmed and
hidden with the
button of the multifunction
steering wheel ›››Fig.11.
Select a menu or an informative display
●
Switch the ignition on.
●
If a message or vehicle symbol is displayed,
press the button ›››Fig.11; several times if
necessary.
●
To change menus, use or buttons.
●
To open the menu or the information dis-
played, press the button or wait a few sec-
onds until the menu or the informative display
opens automatically.
Changing menu settings
●
In the menu displayed, turn the right thumb-
wheel of the multifunction steering wheel until
the desired option of the menu is highlighted.
The option appears framed.
●
Press the button to make the required
modications. A mark indicates that the sys-
tem or function is activated.
Back to menu selection
●
Press the or button.
36
Driver information
Infotainment system op-
eration and displays
Introduction
The infotainment system brings together im-
portant vehicle functions and systems into a
single central control unit, e.g. air conditioning,
menu settings, radio equipment and the navi-
gation system.
The actual number of menus available and the
name of the various options will depend on the
vehicle’s electronics and equipment.
General operating information
General information on the operation of the
infotainment system, as well as on the warning
and safety instructions that must be taken into
account, is found in ›››
page281.
How to move through the dierent menus
and select them
●
Switch the ignition on.
●
If the infotainment system is o, switch it on.
●
The dierent menus are selected directly on
the touch screen using texts, icons or buttons.
If the box is checked
, the function is activa-
ted.
Pressing the menu button will always take
you to the last menu used.
Any changes made using the settings menus
are automatically saved on closing those me-
nus
Scroll bar: Some menus and functions show
more content above or below those displayed
on the screen at that time, for example, long
lists of settings. Press on the scroll bar and drag
up or down.
Tutorial
The rst time you connect the Infotainment
system, a system tutorial will open with a brief
description of the main functions and how to
use it.
Help
In the Help menu can be found more informa-
tion and tips for using the infotainment system.
WARNING
Any distraction may lead to an accident, with
the risk of injury. Operating the Infotainment
system while driving could distract you from
traic.
Note
After starting the engine with a 12-volt bat-
tery that is heavily discharged or recently
replaced, some system settings such as
time, date, personalised comfort settings,
programming and user accounts might be al-
tered or deleted. Check and correct these
settings when the battery is suiciently
charged.
Driver information
37
Infotainment system operation and displays
A
B
C
D
E
F
G
Explanation of the function buttons
Fig.12 Schematic representation: Overview of
the possible function buttons on the screen.
Top part of the screen
Main menu display mode:
: main menu with widget views.
: main menu in tile mode (functions of
the Infotainment system).
Shortcuts to infotainment system func-
tions with the option of adding or remov-
ing functions.
Active functions that do not appear in
zone
B
.
Status bar. Information bar showing the
system status, such as: time, phone cover-
age, phone charge level, Qi charger status,
user privacy mode.
Bottom part of the screen
Climabar ›››page147.
Segments
Scroll down to view the control centre and
system notications.
Change the display of the active function
on the home screen. For example, under
Navigation switch from Map to Informa-
tion on route guidance; or under Assisted
parking switch from Rear camera display
to Manoeuvring status.
38
Driver information
A
B
Don't show again
End
Initial conguration wizard
Fig.13 Schematic representation: Initial
conguration wizard.
The initial conguration wizard will help you to
set up your Infotainment system the rst time
you switch it on.
Whenever you switch on the infotainment sys-
tem, the initial setup screen will be displayed
›››
Fig.13 if any parameters have not been set
(marked with “ ”) or if the Don't show again
function button has not been pressed.
Conguration options:
Tap it to access the basic conguration
menu of the infotainment system such as
navigation to home, mobile connection,
radio stations, etc.
Tap to access the infotainment system's
advanced conguration menu.
Disables the possibility of
changing the settings of the Infotainment
system. If you wish to perform the initial
settings, you will need to access via Set-
tings.
Once one or more settings have been
applied, press to nalise the setup in the
main menu of the wizard.
Driver information
39
Infotainment system operation and displays
Assistance systems and vehicle settings
Fig.14 Schematic representation: Assist
systems and vehicle settings
Press
›››Fig.14
A
, or
Vehicle in the
main menu to open the assistants and vehicle
settings menu. Next, clicking on any of the me-
nus located in the left area
B
, displays the
settings menu or the selected assist systems
on the display.
The number of assistance systems and settings
depend on the version and the country in
question.
Assistants
●
Parking
–
Automatic parking brake activation
›››page226.
–
Park assist ›››page231.
–
Trailer Assist ›››page253
–
Rear Cross Traic Alert ›››page256.
–
Automatic Parking System Plus with mem-
ory function ›››page240
–
Automatic parking system plus with remote
function (My CUPRA App) ›››page245
●
Smart Assistants
–
Switch the Start-Stop system on/o
›››page175
–
Speed limiter ›››page200
–
Adaptive cruise control (ACC)
›››page204.
–
Lane Assist ›››page215.
–
Emergency braking assistance system
Front Assist ›››page211.
–
Driving assistant (Travel Assist)
›››page218
–
Emergency Assist ›››page221
–
Hill Descent Control (HDC) ›››page183.
–
Predictive speed adjustment
›››page209.
–
Eco Assist ›››page203.
●
Driver alerts
–
Drowsiness monitor ›››page27.
–
Speed warning ›››page31.
–
Side Assist ›››page222.
–
Door opening warning ›››page257.
40
Driver information
–
Trailer detection ›››page329.
–
Traic hazard alert ›››page209.
–
Attention monitor ›››page29.
Vehicle
●
Instrument cluster ›››page23.
●
Lighting ›››page137.
●
Mirrors ›››page141.
●
Closing ›››page98.
●
Lights ›››page131.
●
Windows ›››page141.
●
Tyres ›››page385.
●
Windscreen wipers ›››page139
●
Electric drive (PHEV hybrid vehicles) .
›››page170
●
Seats ›››page124
Driver information
41
Infotainment system operation and displays
Vehicle information
Fig.15 Schematic representation: Vehicle
information and status.
Pressing
Vehicle in the main menu opens
the Vehicle menu with the following subme-
nus:
Vehicle assistants ›››page39
Vehicle settings ›››page39
Vehicle status
The warnings regarding faults, incidents,
memorisation of the tyre pressure or in-
formation about the next inspection serv-
ice are displayed.
Driving data
The average consumption, average
speed, distance travelled, trip duration
and range are shown. It has 3 memories:
“Since start”, “Long-term” and “Since refu-
elling”.
The “Since start” and “Long-term” memo-
ries can be reset by pressing button .
42
Driver information
Departure menu
Fig.16 Schematic representation: departure
menu.
In the departure menu you can set some func-
tions before leaving the vehicle. When you
switch o the ignition, the departure menu is
displayed on the infotainment system.
The inputs that are displayed depend on the
equipment and, if applicable, are only available
under certain conditions. Examples of adjusta-
ble functions are:
●
Charging the high-voltage battery
●
Stationary air conditioning or heating
●
Interior monitoring
●
Save parking process
Hide
When you leave the vehicle, the departure
menu is hidden automatically. Depending on
the equipment, it is also hidden after a certain
amount of time.
●
Press to manually hide the departure
menu.
Adjust
You can adjust the order of the displayed in-
puts.
●
Press .
●
Sort the inputs according to your preferen-
ces.
●
Press again.

Related Topics

Popular Owner Manuals