2024-2026 Cupra Terramar SUV Miscellaneous situations -> Jump start User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Miscellaneous situations -> Jump start for Your Cupra Terramar SUV First Generation (2024-2026)

340
Miscellaneous situations
Changing the rear window wiper blade
●
Separate the wiper arm from the rear win-
dow.
●
Remove the blade from the holder below the
centre. During this operation, hold the wiper
arm rmly.
●
Fit the new blade (of the same length and
type) into the housing of the wipe arm by
pressing it in place. When doing so, hold the
wiper arm by the upper end.
●
Fold the wiper arm and rest it on the window.
WARNING
Worn or dirty windscreen wiper blades re-
duce visibility and increase the risk of acci-
dent and serious injury.
●
Always replace damaged or worn wind-
screen wiper blades or blades that no longer
clean the windscreen properly.
NOTICE
●
Damaged or dirty windscreen wipers could
scratch the glass.
●
If products containing solvents, rough
sponges or sharp objects are used to clean
the blades, the graphite layer will be dam-
aged.
●
Never use fuel, nail varnish remover, paint
thinner or similar products to clean the win-
dows.
●
In icy conditions, always check that the
wiper blades are not frozen to the glass be-
fore using the wipers. In cold weather, it may
help to leave the vehicle parked with the wip-
ers in service position ›››page338.
NOTICE
●
To prevent damage to the bonnet and the
wiper arms, only leave them in the service
position.
●
Before driving, always lower the wiper
arms.
Jump start
Introduction
If the engine fails to start because of a dis-
charged 12-volt battery, the battery can be
connected to the battery of another vehicle to
start the engine.
Jump leads complying with the DIN 72553
standard are needed for starting (see cable
manufacturer's instructions). The wire cross
section must be at least 25 mm
2
for petrol en-
gines and at least 35 mm
2
for diesel engines.
NOTICE
To avoid considerable damage to the vehicle
electrical system, take careful note of the fol-
lowing:
●
If the jump leads are connected incor-
rectly, a short circuit may occur.
●
Use only jump leads with fully insulated
clamps.
●
Do not allow the vehicles to come into con-
tact with each other, otherwise current may
start to ow as soon as the positive poles are
connected.
Jump start socket (ground termi-
nal)
Fig.209 In the engine compartment: jump
start socket (ground terminal).
Miscellaneous situations
341
Jump start
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
The jump start socket (ground terminal) is
used for connecting the black jump lead
›››Fig.209
A
.
Only use this socket (ground terminal) in your
vehicle when jump starting.
Jump start: description
Fig.210 Jump lead connection diagram.
The discharged battery must be properly con-
nected to the on-board network.
Make sure that the clamps have suicient
metal contact when connecting them to the
poles.
Jump lead terminal connections
The jump leads should only be connected in
the order 1 > 2 > 3 > 4 ›››
Fig.210.
Switch o the ignition of both vehicles
›››
.
Connect one end of the red jump lead to
the positive
+
terminal of the vehicle with
the at battery
A
.
Connect the other end of the red jump
lead to the positive terminal
+
in the vehi-
cle providing assistance
B
.
Connect one end of the black jump lead
C
to a suitable ground terminal, to a solid
piece of metal in the engine block, or to
the motor block itself.
Connect the other end of the black jump
lead
D
to a suitable ground terminal, a
solid metal component bolted to the en-
gine block or to the engine block itself of
the vehicle with the at battery. Do not
connect it to a point near the battery.
Position the leads in such a way that they
cannot come into contact with any rotat-
ing part in the engine compartment.
Starting
Start the engine of the vehicle supplying
the current and leave it running at idle.
Start the engine of the vehicle with a dis-
charged battery and wait 2 to 3 minutes
until the engine runs.
Disconnecting the jump leads
Before disconnecting the jump leads,
switch o the dipped beam headlight if it
is on.
Turn on the heating fan and the vehicle's
heated rear window when the battery is
discharged to reduce the voltage peaks
that occur while disconnecting the bat-
tery.
While the engines are still running, discon-
nect the cables in the reverse order in
which they were connected.
If the engine does not start after 10 seconds,
wait for approximately 1 minute and then try
again.
WARNING
●
Please note the safety warnings referring
to working in the engine compartment
›››page351.
●
The battery supplying the current must
have the same voltage (12V) as the at bat-
tery. Failure to comply could result in an ex-
plosion.
●
Never use jump leads when one of the bat-
teries is frozen. Danger of explosion! Even
once thawed, electrolyte leaks can cause
burns. Replace the battery if it is frozen.
●
Keep any sources of ignition (ames, ciga-
rettes, etc.) far enough away from the batter-
ies. They may cause an explosion.

Related Topics

Popular Owner Manuals