2024-2026 Cupra Terramar SUV Wheels and tyres User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Wheels and tyres for Your Cupra Terramar SUV First Generation (2024-2026)

374
Wheels and tyres
Wheels and tyres
Important information
about wheels and tyres
General notes
●
When driving with new tyres, be especially
careful during the rst 600 km (300 miles).
●
If you have to drive over a kerb or similar ob-
stacle, drive very slowly and as near as possible
at a right angle to the obstacle.
●
Check from time to time if the tyres are
damaged (punctures, cuts, cracks or dents).
Remove any foreign objects embedded in the
treads.
●
Damaged wheels and tyres must be replaced
immediately.
●
Keep grease, oil and fuel o the tyres.
●
Replace any missing valve caps as soon as
possible.
●
Mark the wheels before taking them o so
that they rotate in the same direction when put
back.
●
When removed, the wheels or tyres should
be stored in a cool, dry and preferably dark
place.
Low prole tyres
Low prole tyres have a wider tread, a larger
wheel diameter and a lower sidewall height.
This results in more agile driving behaviour.
Low prole tyres may deteriorate more quickly
than standard tyres, for instance due to
heavy impacts, potholes, manhole covers and
kerbs. Correct tyre pressure is very important
›››page376.
To avoid damage to tyres and wheels, drive
with special care when driving on roads in poor
condition.
Visually check your wheels every 3000 km.
If the tyres or rims have received a heavy im-
pact or have been damaged, have a special-
ised workshop check whether or not it is nec-
essary to change the tyre.
Low prole tyres may deteriorate more quickly
than standard tyres.
Concealed damage
Damage to tyres and rims is often not readily
visible. If you notice unusual vibration or the
car pulling to one side, this may indicate that
one of the tyres is damaged. Reduce speed im-
mediately if there is any reason to suspect that
damage may have occurred. Inspect the tyres
for damage. If no external damage is visible,
drive slowly and carefully to the nearest speci-
alised workshop and have the car inspected.
Foreign objects inserted in the tyre
●
Do not remove foreign bodies if they have
penetrated through the tyre wall!
●
If the vehicle comes with a tyre mobility sys-
tem, where necessary seal the damaged tyre as
shown in section ›››page388.
Use a specialised workshop for repair or re-
placement. CUPRA recommends going to a
specialised CUPRA dealer or any SEAT dealer-
ship for this purpose.
The sealant inside the tyre tread wraps around
the foreign body and provisionally seals the
tyre.
Tyres with directional tread pattern
An arrow on the tyre sidewall indicates the
rotation direction on directional tyres. Always
note the rotation direction indicated when
mounting the wheel. This makes sure that op-
timal use is made of tyre properties in terms of
aquaplaning, grip, excessive noise and wear.
Retrotting of accessories
If you wish to change or t wheels, rims or
wheel trims, we recommend that you consult
with a specialised CUPRA Service or SEAT Oi-
cial Service centre for advice regarding current
technical recommendations.
Speed symbols
The speed rating indicates the maximum
speed permitted for the tyres.
Wheels and tyres
375
Important information about wheels and tyres
P
Q
R
S
T
U
H
V
Z
W
Y
max.150 km/h (93mph)
max.160 km/h (99mph)
max.170 km/h (106mph)
max.180 km/h (112mph)
max.190 km/h (118mph)
max.200 km/h (124mph)
max.210 km/h (130mph)
max.240 km/h (149mph)
max.240km/h (149mph)
max.270 km/h (168mph)
max.300 km/h (186mph)
WARNING
●
New tyres do not have maximum grip dur-
ing the rst 600km. Drive particularly care-
fully to avoid possible accidents.
●
Never drive with damaged tyres. This may
cause an accident.
●
If you notice unusual vibrations or if the
vehicle pulls to one side when driving, stop
the vehicle immediately and check the tyres.
●
Never use old tyres or those with an un-
known history of use.
New wheels and tyres
It is best to have all wheels and tyres serviced
by a specialised workshop. There they have the
required knowledge, the special tools and the
corresponding spare parts.
●
Even winter tyres lose their grip on ice. If you
have installed new tyres, drive the rst 600 km
carefully and at a moderate speed.
●
All four wheels must be tted with tyres
of the same type, size (rolling circumference)
and, if possible, tread pattern.
●
When changing tyres, do not change just
one; change at least two on the same axle.
●
If you want to equip your vehicle with a com-
bination of tyres and rims that are dierent to
those tted in the factory, inform your special-
ised workshop before purchasing them
The sizes of the rims and tyres approved for
your vehicle are listed in the vehicle documen-
tation (e.g. EC Certicate of Conformity or
COC document). The vehicle documentation
varies depending on the country of residence.
If the type of spare wheel is dierent form
the normal wheels — e.g. in the case of win-
ter tyres or particularly wide tyres — the spare
wheel should only be used temporarily in the
event of a puncture, and the vehicle should be
driven with care. Ret the normal road wheel
as soon as possible.
In vehicles with four-wheel drive, the 4 wheels
must be tted with tyres of the same brand,
type and tread so that the traction system is
not damaged by a dierence in the number of
turns of the wheels. Therefore, in the event of
a puncture, only a spare wheel with the same
perimeter as normal tyres should be used.
Manufacturing date
The manufacturing date is also indicated on
the tyre sidewall (or on the inside face of the
wheel):
DOT ... 2220 ...
this means, for example, that the tyre was
manufactured in the 22nd week of 2020.
WARNING
●
Use only combinations of tyres and rims,
as well as suitable wheel nuts, approved by
CUPRA. Otherwise the vehicle may be dam-
aged, causing an accident.
●
For technical reasons it is not possible to
use wheels of other vehicles; in some ca-
ses not even wheels from the same vehicle
model should be used.
●
Always ensure that the tyres you have
chosen have adequate clearance. When se-
lecting replacement tyres, do not rely en-
tirely on the nominal tyre size marked on the
tyre, since the nominal tyre size can dier
signicantly depending on the manufacturer.
Lack of clearance can damage the tyres or
the vehicle and, as a result, endanger road
safety. Accident hazard!
376
Wheels and tyres
●
Only use tyres that are over 6 years old in
an emergency, and drive with due care.
●
The tting of tyres with run-at properties
is not permitted on your vehicle! Prohibited
use can cause accidents or can damage your
vehicle.
●
If decorative hubcaps are retrotted, make
sure that they allow enough air in to cool the
braking system. Accident hazard!
●
Models with aerodynamic wheel rims
and/or with bolt-on plastic elements (more
enclosed design) increase the likelihood of
ice and snow accumulating on the inside.
This should be taken into account, depend-
ing on the driving situations, as snow or ice
accumulated in the wheels can cause vibra-
tion in the vehicle when it drives at over 40
km/h. It is advisable to remove ice and snow
from the inside of the wheels using hot water.
●
If you drive on dirt or gravel tracks, the
likelihood of stones becoming trapped inside
wheel rims with plastic elements increases
when driving at high speed or in a sporty
manner. If you see that there are stones trap-
ped between the aluminium wheel rim and
the insert, you can attempt to remove them
using pressurised water.
For the sake of the environment
Old tyres must be disposed of according to
each country's laws.
Note
●
A CUPRA Service Centre should be consul-
ted to nd out whether wheels or tyres of
dierent sizes to those originally tted by
CUPRA can be tted, and to nd out about
the combinations allowed between the front
axle (axle 1) and the rear axle (axle 2).
●
Never mount used tyres if you are not sure
of their “previous history”.
Tyre life
Fig.236 Location of the tyre pressure
sticker.
Correct ination pressures and sensible driving
habits will increase the useful life of your tyres.
●
Check tyre pressure at least once a month,
and also prior to any long trip.
●
The tyre pressure should only be checked
when the tyres are cold. Do not reduce the
pressure of warm tyres.
●
Adjust tyre pressure to the load being carried
by the vehicle.
●
In vehicles with a tyre pressure indicator, save
the modied tyre pressure ›››page385.
●
Avoid fast cornering and hard acceleration.
●
Inspect the tyres for irregular wear from time
to time.
Tyre pressure
The tyre pressure values are shown on the
sticker located on the rear frame of the front
left door.
Insuicient or excessive pressure greatly re-
duces the useful life of the tyres and adversely
aects vehicle performance and ride. Correct
ination pressures are very important, espe-
cially at high speeds.
The tyre pressure must be adjusted according
to the load the vehicle is carrying. If the vehicle
is going to be fully loaded, increase the tyre
pressure to the maximum load value shown on
the sticker.
Do not forget the spare wheel when checking
the tyre pressures: Keep this spare wheel ina-
ted to the highest pressure required for the
road wheels.
Wheels and tyres
377
Important information about wheels and tyres
In the case of a minimised temporary spare
wheel (125/70 R16 or 125/70 R18) inate to a
pressure of 4.2 bar as indicated on the tyre
pressure label.
Driving style
Fast cornering, heavy acceleration and hard
braking (squealing tyres) all increase tyre wear.
Wheel balance
The wheels on new vehicles are balanced.
However, certain circumstances may lead to
imbalance (run-out), which is detected as vi-
brations in the steering wheel.
Unbalanced wheels should be rebalanced, as
they otherwise cause excessive wear on steer-
ing, suspension and tyres. A wheel must also
be rebalanced when a new tyre is tted or if a
tyre is repaired.
Incorrect wheel alignment
Incorrect running gear alignment causes ex-
cessive tyre wear, impairing the safety of the
vehicle. If you notice excessive tyre wear, you
should check wheel alignment at a specialised
CUPRA Service or SEAT Oicial Service.
WARNING
Unsuitable handling of the wheels and tyres
may lead to sudden tyre pressure losses,
tread separation or even a blow-out.
●
The driver is responsible for ensuring that
all of the vehicle tyres are correctly inated
to the right pressure. The recommended tyre
pressure is indicated on the label.
●
Check tyre pressures regularly and ensure
they are kept at the indicated pressures. Tyre
pressure that is too low could cause over-
heating, resulting in tread detachment or
even burst tyres.
●
Tyre pressure should be as indicated on the
label when the tyres are cold at all times.
●
Regularly check the cold ination pressure
of the tyres. If necessary, change the tyre
pressure of the vehicle tyres while they are
cold.
●
Regularly check your tyres for damage and
wear.
●
Never exceed the speed limit or loads
specied for the type of tyre tted on your
vehicle.
For the sake of the environment
Under-inated tyres will increase fuel con-
sumption.
Tread wear indicators
Fig.237 Tyre prole: tread wear indicators.
Fig.238 Swapping tyres.
Wear indicators around 1.6mm high can be
found on the base of the original tyre treads,
ordered at regular intervals and running across
the tread ›››
Fig.237. The letters “TWI” or
triangles on the sidewall of the tyre mark the
position of the wear indicators.
378
Wheels and tyres
1)
Follow the regulations of the country you are driving in.
The minimum permitted prole depth
1)
have
been reached when the tyres have worn down
to the wear indicators. Replace the tyres with
new ones ›››
.
With a sporty driving style, check the tread
depth every 5,000 / 10,000km (3,000 /
6,000mi). When checking the tread depth,
check the wear indicators in all the tyre
grooves.
Changing wheels around
In order to wear the wheels in a uniform man-
ner, it is recommended to swap them regularly
according to the diagram ›››Fig.238. The
useful life of all the tyres will then be about the
same time.
WARNING
The tyres must be replaced at the latest when
the tread is worn down to the tread wear indi-
cators. Failure to follow this instruction could
result in an accident.
●
Particularly in diicult driving conditions
such as wet or icy roads. It is important that
the tyre tread be as deep as possible and be
approximately the same on the tyres of both
the front and the rear axles.
●
Lower driving safety due to insuicient
tread depth is particularly evident in vehicle
handling, when there is a risk of “aquaplan-
ing” in deep puddles of water and when driv-
ing through corners, and braking is also ad-
versely aected.
●
The speed has to be adapted accordingly,
otherwise there is a risk of losing control over
the vehicle.
Wheel nuts
The wheel nuts and rims have been designed
to be part of an assembly. When installing
dierent wheels (for instance alloy wheels or
wheels with winter tyres) it is important to use
the correct wheel nuts with the right length
and correctly shaped bolt heads. This ensures
that wheels are tted securely and that the
brake system functions correctly.
The wheel nuts must be clean and turn easily.
A special adapter is required to turn the anti-
theft wheel nuts ›››
page382.
WARNING
Wheel nuts should never be greased or oiled.
●
Use only wheel nuts which belong to the
wheel.
●
If the required torque of the wheel nuts is
too low, they could loosen whilst the vehicle
is in motion. Risk of accident! If the tighten-
ing torque is too high, the wheel nuts and
threads can be damaged.
NOTICE
See ›››page384 to nd out the recommen-
ded tightening torque for wheel nuts for alloy
rims.
Winter tyres
●
Winter tyres must be tted on all four
wheels.
●
Only use winter tyres that are approved for
your vehicle.
●
Please note that the maximum permissible
speed for winter tyres may be lower than for
summer tyres.
●
Also note that winter tyres are no longer ef-
fective when the tread is worn down.
●
After tting the wheels you must always
check the tyre pressures. When doing so,
take into account the correct tyre pressures
listed on the rear of the front left door frame
›››page376.
In winter road conditions winter tyres will con-
siderably improve vehicle handling. The design
of summer tyres (width, rubber compound,
tread pattern) gives less grip on ice and snow.
This applies particularly to vehicles equipped
with wide section tyres or with high speed
tyres (code letters H, V or Y on the sidewall).
Wheels and tyres
379
Important information about wheels and tyres
1)
COC = certicate of conformity.
Only use winter tyres of the correct type ap-
proved for your vehicle. The sizes of these
tyres are specied in the vehicle's documents
(e.g. EC Certicate of Conformity or COC
1)
).
The vehicle documentation varies depending
on the country of residence.
Winter tyres lose a great deal of their proper-
ties when the tread is worn down to a depth of
4mm.
The performance of winter tyres is also se-
verely impaired by ageing, even if the tread is
still much deeper than 4 mm.
A code letter indicating the speed limit is stam-
ped on all winter tyres ›››
page374.
In the infotainment system's Vehicle settings
menu, a speed warning can be set in the Tyres
menu.
Vehicles capable of exceeding these speeds
must have an appropriate sticker attached so
that it is visible to the driver. Suitable stickers
are available at specialised CUPRA Services,
SEAT Oicial Service centres and specialised
workshops. Please note the regulations to this
eect in your country.
“All-weather” tyres can also be used instead of
winter tyres.
Using winter tyres with a V-rating
Please note that the generally applicable
240km/h (149mph) speed for winter tyres
with the letter V is subject to technical restric-
tions; the maximum permissible speed for
your vehicle may be signicantly lower. The
maximum speed limit for these tyres depends
directly on the maximum axle weights for your
car and on the listed weight rating of the tyres
being used.
It is best to contact a specialised CUPRA Serv-
ice or SEAT Oicial Service to check the max-
imum speed which is permissible for the V-
rated tyres tted on your car on the basis of
this information.
WARNING
Exceeding the maximum speed permitted for
the winter tyres tted on your car can cause
tyre failure, resulting in a loss of control of
the vehicle – risk of accident.
For the sake of the environment
When winter is over, change back to summer
tyres at an appropriate moment. In tempera-
tures above +7°C (+45°F), performance will be
improved if summer tyres are used. Rolling
noise, wear and energy consumption will all
be reduced.
Snow chains
Snow chains are only permitted on the front
wheels, even on 4-wheel drive vehicles.
●
Check that they are correctly seated after
driving for a few yards; correct the position
if necessary, in accordance with the manufac-
turer's tting instructions.
●
Keep your speed below 50km/h (30 mph).
●
If there is a danger of being trapped despite
having tted the chains, it is best to disable the
traction control (TCS) in the ESC ›››page191.
Snow chains will improve braking ability as well
as traction in winter conditions.
For technical reasons, the use of snow chains
is only permitted on the following rim and tyre
combinations:
Tyres Wheel rim Chains
215/55 R17 7.5Jx17 ET40 Max. link
15mm
225/55 R17 7.5Jx17 ET40
Max. link 9
mm
225/50 R18 8x18 ET40
245/45 R18 8x18 ET40
245/40 R19 8x19 ET40
Other dimensions do not allow chains
380
Wheels and tyres
Remove any central wheel trims before tting
snow chains.
WARNING
The use of unsuitable or incorrectly tted
chains could lead to serious accidents and
damage.
●
Always use appropriate snow chains.
●
Observe the tting instructions provided
by the snow chain manufacturer.
●
Never exceed the speed limits when driving
with snow chains.
●
Before tting the chains, check that the
wheel/tyre combination on the table is the
one installed on your vehicle. The combina-
tion can also be found on the technical data-
sheet.
NOTICE
●
Remove the snow chains to drive on roads
without snow. Otherwise they will impair ve-
hicle handling, damage the tyres and wear
out very quickly.
●
Wheel rims may be damaged or scratched
if the chains come into direct contact with
them. CUPRA recommends the use of coated
snow chains.
Changing a wheel
Introduction
Only change a wheel yourself if you are famil-
iar with the necessary operations and safety
measures, if you have the necessary tools and
if the vehicle is parked safely.
Preliminary actions
●
Stop the vehicle on a level surface and in a
safe place, as far away from road traic as pos-
sible.
●
Apply the electronic parking brake.
●
Switch on the hazard warning lights.
●
Automatic transmission: switch on the park-
ing lock P.
●
If towing a trailer, unhitch the trailer from
your vehicle.
●
Lay out the on-board tools ›››page338 and
the wheel to be changed.
●
Follow the legal provisions of each country
(reective vest, warning triangles, light beacon,
etc.).
●
Get all occupants out of the vehicle and
keep them out of the danger zone (e.g. behind
the guard rail).
WARNING
●
Always observe the above steps and pro-
tect yourself and other road users.
●
If you change the wheel on a slope, block
the wheel on the opposite side of the car
with a stone or similar to prevent the vehicle
from moving.
Location and use of the temporary
spare wheel
Fig.239 In the luggage compartment: load
oor raised.
Wheels and tyres
381
Changing a wheel
Fig.240 In the luggage compartment:
remove the subwoofer.
The temporary spare wheel is stored under the
oor panel in the luggage compartment and is
attached by a thumbnut.
The temporary spare wheel has been designed
to be used for short periods of time. Have the
tyre checked and replaced as soon as possible
at a specialised CUPRA Service, SEAT Oicial
Service or at a specialised workshop.
The spare wheel must not be switched for a
spare wheel from another vehicle.
Removing the temporary spare wheel
●
Lift and hold up the oor panel to remove
the temporary spare wheel ›››page316.
●
Turn the thumb wheel anticlockwise
›››Fig.239.
●
Take out the temporary spare wheel.
Getting the spare wheel out of vehicles t-
ted with the optional sound system (with
subwoofer)
To remove the spare wheel, you must rst re-
move the subwoofer.
●
Vehicles without a variable oor in the lug-
gage compartment: pull the oor of the lug-
gage compartment (carpet) upwards to get it
out.
●
Vehicles with a variable luggage compart-
ment oor: lift and secure the oor storage
compartment as explained in ›››page316.
●
Disconnect the subwoofer’s speaker cable
›››Fig.240
1
.
●
Turn the securing wheel anti-clockwise
›››Fig.240
2
.
●
Remove the subwoofer speaker and the
spare wheel.
●
When re-mounting the spare tyre, place the
subwoofer on the base of the wheel rim with
care. When doing so, the tip of the “FRONT”
arrow on the subwoofer should point forward.
●
Reconnect the speaker cable and rmly
rotate the securing wheel clockwise so that
the subwoofer system and wheel are rmly in
place.
Chains
For technical reasons, snow chains must not be
used on the temporary spare wheel.
If you have a puncture on one of the front
wheels when using snow chains, t the tempo-
rary spare wheel in place of one of the rear
wheels. Fit the snow chains on the rear wheel
that you have removed and replace the punc-
tured front wheel with this wheel.
WARNING
●
After tting the temporary spare wheel,
check the tyre pressures as soon as possible.
Failure to do so may cause an accident. The
tyre pressure is listed on the back of the left
front door frame ›››page376.
●
Do not drive at over 80km/h (50mph)
when the temporary spare wheel is tted on
the vehicle: Accident risk!
●
Never travel more than 200km using a
temporary spare wheel.
●
Avoid heavy acceleration, hard braking and
fast cornering: Accident risk!
●
Never use more than one temporary spare
wheel at the same time, risk of accident.
●
No other type of tyre (normal summer or
winter tyre) may be tted on the compact
temporary spare wheel rim.
●
If you are driving using the spare wheel,
the ACC system could automatically switch
o during the journey. Switch o the system
when starting o.
382
Wheels and tyres
Wheel nut caps
Fig.241 Wheel: wheel nuts with caps.
Removal
●
Fit the plastic clip (vehicle tools ›››Fig.205)
over the cap until it clicks into place
›››Fig.241.
●
Remove the cap with the plastic clip.
The caps protect the wheel nuts and should be
remounted after changing the tyre.
The anti-theft wheel locking bolt has a spe-
cial cap. This only ts on anti-theft locking
bolts and is not for use with standard wheel
nuts.
Anti-theft wheel nuts
Fig.242 Anti-theft wheel nut with cap and
adapter.
Loosening the anti-theft wheel nut
●
Remove the wheel trim or hub cap.
●
Insert the special adapter ›››Fig.242
1
(vehicle tools ›››
page338) onto the anti-theft
wheel nut and push it on as far as it will go.
●
Insert the wheel wrench (vehicle tools) onto
the adapter as far as it will go.
●
Remove the wheel nut ›››page382.
Note
Make a note of the code number of the anti-
theft wheel nut and keep it in a safe place,
but not in your vehicle. If you need a new
adapter, you can obtain it from the special-
ised CUPRA service or the SEAT Oicial Serv-
ice, by giving the code number.
Loosening wheel nuts
Fig.243 Tyre change: loosen the wheel
nuts.
Use only the wheel wrench belonging to the
car to loosen the wheel nuts.
Loosen the wheel nuts only about one turn
before raising the vehicle with the jack.
If the wheel nut is very tight, carefully push on
the end of the wheel wrench with your foot.
Hold on to the vehicle for support and take
care not to slip during this operation.
Loosening wheel nuts
●
Fit the box spanner into the bolt as far as it
will go ›››Fig.243.
●
Hold the wrench at the end and rotate
the bolt approximately one turn anticlock-
wise››› .
Wheels and tyres
383
Changing a wheel
Important information about wheel nuts
Factory-tted rims and wheel nuts are specially
matched during construction. Therefore, if dif-
ferent rims are tted, the correct wheel nuts
with the right length and heads must be used.
This ensures that wheels are tted securely
and that the brake system functions correctly.
In certain circumstances, you should not even
use wheel nuts from vehicles of the same
model.
WARNING
If the wheel nuts are not properly tightened,
they could come loose while driving and
cause an accident, serious injury and loss of
vehicle control.
●
Use only wheel nuts which correspond to
the rim in question.
●
Never use dierent wheel nuts.
●
Wheel nuts and threads should be clean,
free of oil and grease, and it should be possi-
ble to screw them easily.
●
To loosen and tighten wheel nuts, only use
the wheel wrench that came with the car
from the factory.
●
The wheel nuts should only be loosened
slightly (about one turn) before raising the
vehicle with the jack. Risk of accident!
●
Never apply grease or oil to wheel nuts or
to the wheel hub threads. Even if the bolts
have been tightened to the required torque,
they could come loose while driving.
●
Never loosen the screwed joints of wheel
rims with bolted ring trims.
●
If wheel nuts are tightened below the re-
quired torque, the bolts and rims could come
loose while driving. If tightening torque is too
high, the wheel nuts or threads can be dam-
aged.
Raise the vehicle
Fig.244 Jack position points.
Fig.245 Crossbar: mounting the jack on
the vehicle.
●
Rest the jack (vehicles tools) on rm ground.
If necessary use a large, strong board or similar
support. If the surface is slippery (for example
tiles) place the jack on a rubber mat or similar
to prevent it from slipping ››› .
●
Look on the crossbar for the mark of the
jack support point (sunken area) closest to the
wheel to be changed ›››Fig.244.
●
Turn the jack crank handle, located below
the crossbar support point, to raise it until the
tab
1
›››
Fig.245 is below the housing that is
provided.
●
Align the jack so that the tab
1
“grips”
onto the housing provided on the cross mem-
ber and the mobile base
2
is resting on the
ground. The base plate
2
should fall vertically
with respect to the support point
1
.
●
Continue turning the jack until the wheel is
slightly lifted o the ground.
384
Wheels and tyres
WARNING
The factory-supplied jack is only designed
for changing wheels on this model. On no
account attempt to use it for lifting heavier
vehicles or other loads. Risk of injury.
●
Make sure the jack remains stable. If the
surface is slippery or soft, the jack could slip
or sink, respectively, with the consequent
risk of causing injuries.
●
Lift the vehicle using only the jack supplied
from the factory. Other jacks, even those ap-
proved for other CUPRA models could slip,
with the consequent risk of injury.
●
Place the jack only at the support points
provided on the crossbar and align it. Other-
wise, the jack could slip because it does not
have suicient grip on the vehicle. Risk of
injury!
●
You should never place a body limb such as
an arm or leg under a raised vehicle that is
solely supported by the jack.
●
If you have to work underneath the vehi-
cle, you must use suitable stands additionally
to support the vehicle. Accident risk!.
●
Never raise the vehicle if it is tilting to one
side or the engine is running.
●
Never start the engine when the vehicle is
raised. The vehicle may come loose from the
jack due to the engine vibrations.
NOTICE
●
The vehicle must not be raised on the
crossbar. Place the jack only at the support
points provided on the crossbar and align it.
Otherwise, the vehicle may be damaged.
●
Any type of load or weight applied to the
external trim/door (treading on it, tting the
jack, resting heavy objects, etc.) can cause
damage to it. CUPRA accepts no responsibil-
ity for any damages caused by improper use
of the external trim or body.
Removing and installing a wheel
Change the wheel after loosening the wheel
nuts and raising the vehicle with the jack.
When removing/tting the wheel, the rim may
hit and damage the brake disc. Therefore,
please take care and get a second person to
assist you.
Taking o the wheel
●
Unscrew the nuts with the wheel wrench and
place them on a clean surface.
●
Remove the wheel.
Putting on the spare wheel
Check the rotation direction of the tyre
›››
page385.
●
Place the spare wheel or temporary spare
wheel into position.
●
Screw in the wheel nuts and tighten them a
little with the wheel wrench.
●
Use the appropriate adapter to tighten the
anti-theft wheel nuts.
●
Carefully lower the vehicle using the jack.
●
Use the wheel wrench to tighten all of the
wheel nuts clockwise. Tighten the bolts in di-
agonal pairs (not in a circle).
●
Put the caps, trim or full hubcap back on.
Fitting the minimised spare wheel (depend-
ing on the version)
For technical reasons (brake disc size), it may
not be possible to t the minimised spare
wheel on the front axle.
In the event of a puncture or damage to a front
tyre, follow the instructions below:
1. Remove the rear wheel on the same side
as the damaged front wheel.
2. Fit the minimised spare wheel on the rear
axle.
3. Replace the damaged front wheel with the
removed rear wheel.
If necessary, check that the tyre pressures are
correct as soon as possible.
Wheels and tyres
385
Tyre pressure monitor system
Tightening torque of the wheel nuts
The required tightening torque for wheel nuts
for alloy rims is 140Nm.
After changing a wheel, have the tightening
torque checked immediately with a torque
wrench that is working perfectly.
The wheel nuts should be clean and turn
easily. Before tting the spare wheel, inspect
the wheel condition and hub mounting surfa-
ces. These surfaces must be clean before t-
ting the wheel.
Before checking the tightening torque, have
any rusty wheel nuts that are diicult to screw
replaced and clean the wheel hub threads.
Never apply grease or oil to wheel nuts or to
the wheel hub threads. Even if the bolts have
been tightened to the required torque, they
could come loose while driving.
Tyres with directional tread pattern
Tyres with directional tread pattern have been
designed to operate best when rotating in only
one direction. An arrow on the tyre sidewall
indicates the rotation direction on tyres with
directional tread. Always observe the indicated
rotation direction in order to guarantee opti-
mum grip and help avoid aquaplaning, exces-
sive noise and wear.
If the tyre is mounted in the opposite rotation
direction, drive with extreme caution, as the
tyre is no longer being used correctly. This is of
particular importance when the road surface
is wet. Change the tyre as soon as possible or
remount it with the correct rotation direction.
Works after changing a wheel
●
Replace the hub caps or wheel nut caps (de-
pending on equipment).
●
Return all tools to their proper storage loca-
tion.
●
If the replaced wheel does not t in the spare
wheel housing, store it safely in the luggage
compartment ›››page314.
●
Check the tyre pressure of the newly moun-
ted tyre as soon as possible.
●
In vehicles tted with a tyre pressure indi-
cator, adjust the pressure and store it in the
memory ›››page385.
●
Have the tightening torque of the wheel nuts
checked as soon as possible with a torque
wrench ›››page384. Meanwhile, drive care-
fully.
●
Have the at tyre replaced as quickly as pos-
sible.
Tyre pressure monitor sys-
tem
Tyre pressure monitor indicator
Fig.246 Instrument cluster: warning of loss
of tyre pressure.
The tyre pressure monitoring system compares
the individual speeds of each wheel and thus
the dynamic radius with the help of the ABS
sensors.
If the rolling circumference of one or more
wheels has changed, the tyre pressure moni-
toring indicator will indicate this on the instru-
ment cluster through a warning lamp and a
warning to the driver ›››
Fig.246. If only one
tyre is aected, its position on the vehicle will
be indicated.
Loss of pressure: Check left tyre pressure!
Change in wheel diameter
The wheel diameter changes when:
386
Wheels and tyres
●
Tyre pressure is changed manually.
●
The tyre pressure is insuicient.
●
The tyre's structure is damaged.
●
The vehicle is not level due to a load.
●
The wheels on an axle are subject to a heav-
ier load (e.g. with a heavy load).
●
The vehicle is tted with snow chains.
●
The temporary spare wheel has been tted.
●
One wheel has been changed on an axle.
There may be a delay in the reaction of the tyre
pressure monitoring indicator or it may not
indicate anything under certain circumstances
(e.g. sporty driving, snow-covered or unpaved
roads, or when driving with snow chains).
Calibrate the tyre pressure monitoring indi-
cator
After changing the tyre pressure or replacing
one or more wheels, the tyre pressure mon-
itoring indicator must be recalibrated. This
should also be done, for example, when swap-
ping the front and rear tyres.
It should be calibrated with the vehicle stop-
ped and its tyres cold. If calibrated while the
tyres are hot, the pressure check and calibra-
tion procedure should be repeated when cold
before the next trip.
●
Switch the ignition on.
●
Save the new ination pressure in the info-
tainment system: function button > Ve-
hicle > Exterior > Tyres ›››page41.
●
OR: > Vehicle > Status > Tyres.
After storing the new ination pressure, a con-
rmation message will be displayed, the warn-
ing light in the instrument cluster will ash
briey and a driver alert tone will be played.
The tyre pressure loss indicator uses the ABS
sensors to compare the turns of each wheel
and, therefore, their tread circumferences,
among other aspects. The set values are col-
lected and monitored after a long journey at
dierent speeds.
For example, if the wheels are under very
heavy loads, the tyre pressure must be in-
creased to the total recommended tyre pres-
sure before calibration ›››Fig.246.
WARNING
If the tyres are inated to dierent pressures,
or to a pressure that is too low, a tyre may be
damaged and control of the vehicle may be
lost. This could lead to a serious or even fatal
accident.
●
If the lamp lights up, reduce speed im-
mediately and avoid any sudden turning or
braking manoeuvres. Stop as soon as possi-
ble, and check the pressure and status of all
tyres.
●
The tyre pressure loss indicator only works
correctly if all the tyres are at the correct
pressure when cold, and it is subsequently
calibrated according to the described proce-
dure.
●
If the tyres have no punctures and do not
need to be replaced immediately, drive to the
nearest specialist workshop at low speed and
have the tyre pressure checked and correc-
ted.
Note
●
When driving for the rst time with new
tyres at high speeds, the tyres may expand
slightly, which may result in an air pressure
warning.
●
If a low tyre pressure is detected when the
ignition is switched on, an audible warning
will sound. If the system fails, an audible sig-
nal sounds.
●
Driving on unpaved roads for a long pe-
riod of time, or sporty driving, may tempora-
rily deactivate the system. The warning lamp
shows a fault, but disappears when road con-
ditions or driving behaviour change.
●
Do not only rely on the tyre pressure mon-
itoring system. Check the tyres regularly to
ensure that the tyre pressures are correct
and that the tyres are free of damage such as
punctures, cuts, gouges and dents. Remove
any non-puncturing objects from the tyres.
Wheels and tyres
387
Tyre repair
●
The tyre pressure monitoring indicator
does not function when there is a fault in the
ESC or ABS ›››
page189.
Troubleshooting
Low tyre pressure
The control lamp lights up in yellow.
The ination pressure of one or more wheels
is much lower than the value set by the driver,
or the tyre has structural damage. In addition,
a audible warning sounds and a text message is
displayed on the instrument cluster display.
●
Stop the vehicle! Stop the vehicle as
soon as possible in a safe place.
●
Check all tyres and pressures.
●
Replace any damaged tyres.
Fault in the tyre pressure loss indicator
The control lamp ashes for approximately 1
minute and then lights up permanently in yel-
low.
●
If the tyre is inated correctly, switch the ig-
nition o and on again.
●
Re-calibrate the tyre pressure monitoring
system ›››page385
●
If the fault continues, go to a specialised
workshop.
Tyre repair
TMS (Tyre Mobility System) punc-
ture repair kit
The puncture repair kit (Tyre Mobility System)
will reliably seal punctures caused by the pene-
tration of a foreign body of up to about 4 mm
in diameter. Do not remove foreign objects,
e.g. screws or nails, from the tyre.
After inserting the sealant residue in the tyre,
you must again check the tyre pressure about
10minutes after starting the engine.
You should only use the tyre mobility set if the
vehicle is parked in a safe place, you are famil-
iar with the procedure and you have the nec-
essary tyre mobility set. Otherwise, you should
seek professional assistance.
Tyre sealant must not be used in the follow-
ing cases:
●
If the wheel rim has been damaged.
●
In outside temperatures below -20°C (-4°F).
●
If the cut or punctures in the tyres are larger
than 4 mm.
●
If the tyre has been driven on with very low
ination pressure or no tyre pressure.
●
If the expiry date of the sealant bottle has
passed.
WARNING
Using the puncture repair kit can be danger-
ous, particularly when lling the tyre on the
roadside. To reduce the risk of serious injury,
consider the following:
●
Stop the vehicle as soon as possible in a
safe place. Park it at a safe distance from
road traic to ll the tyres.
●
Make sure the ground is at and rm.
●
All occupants, especially children, should
stay a safe distance away from the work area.
●
Turn on the hazard lights to warn other
road users.
●
Always switch o the engine and activate
the electronic parking brake to reduce the
risk of accidental vehicle movement.
–
Vehicles with automatic transmission:
switch on the parking lock P.
●
Use the puncture repair kit only if you are
familiar with the necessary operations. Oth-
erwise, you should seek professional assis-
tance.
●
The puncture repair kit should only be
used in an emergency, to reach the nearest
garage.
●
Replace tyres repaired with the puncture
kit as soon as possible.
388
Wheels and tyres
1
2
3
4
5
6
7
8
9
10
11
●
The sealant is harmful to health and must
be cleaned o immediately if it comes into
contact with the skin.
●
Always keep the puncture repair kit out of
the reach of children.
WARNING
A tyre lled with sealant does not have the
same driving properties as a conventional
tyre.
●
Never drive faster than 80km/h (50mph).
●
Avoid full throttle, braking heavily and cor-
nering at high speeds.
●
Drive for only 10 minutes at a maximum
speed of 80 km/h (50mph) and then check
the tyre.
For the sake of the environment
Dispose of used or expired tyre sealant in
accordance with the relevant legal require-
ments.
Note
You can purchase new bottles of tyre sealant
from CUPRA specialist dealers or any SEAT
network dealer.
Note
Take into account the separate instruction
manual provided by the tyre mobility system
manufacturer.
Tyre mobility system contents
Fig.247 Standard display: contents of the
tyre mobility system.
The tyre mobility system is located under-
neath the oor covering in the luggage com-
partment. Includes the following components
›››
Fig.247:
Valve insert remover
A sticker to be stuck to the instrument
cluster, in the driver's eld of view, as a
reminder of the advisable maximum speed
“max.80 km/h” or “max.50mph”
Filler tube with cap
Air compressor (depending on the version,
the model may vary).
ON/OFF switch
Air bleed screw (it can also be integrated in
the inator tube).
Warning provided by tyre pressure moni-
toring system (it can also be integrated in
the inator tube).
Tube for inating tyres
12 volt connector
Bottle of sealant
Spare tyre valve
The valve insert remover
1
has a gap at the
lower end for a valve insert. The valve insert
can only be screwed or unscrewed in this way.
This also applies to its replacement part
11
.
Sealing and inating a tyre
Sealing the tyre
●
Unscrew the tyre valve cap and insert. Use
the device ›››Fig.247
1
to remove the valve
cap. Place it on a clean surface.
●
Shake the tyre sealant bottle vigorously
›››
Fig.247
10
.
●
Screw the tyre ination hose ›››Fig.247
3
into the tyre sealant bottle. The bottle's seal
will break automatically.
Wheels and tyres
389
Tyre repair
●
Remove the ller cap ›››Fig.247
3
and
screw the open end of the tube into the tyre
valve.
●
With the bottle upside down, empty all of
the contents into the tyre.
●
Remove the bottle from the valve.
●
Replace the valve insert with the device
›››Fig.247
1
onto the tyre valve.
Inating the tyre
●
Screw the tyre ination tube of the compres-
sor ›››Fig.247
8
onto the tyre valve.
●
Check that the air evacuation screw is
closed ›››Fig.247
6
.
●
Start the engine and leave it running.
●
Attach the connector ›››Fig.247
9
to the
vehicle’s 12 volt power outlet ›››
page261.
●
Switch on the air compressor with the
ON/OFF switch ›››Fig.247
5
.
●
Keep the air compressor running until it
reaches a pressure of 2.0-2.5 bar (29-36psi/
200-250kPa). A maximum of 8 minutes.
●
Disconnect the air compressor.
●
If it does not reach the indicated pressure,
unscrew the tyre inater tube from the valve.
●
Move the vehicle 10m so that the sealant is
distributed throughout the tyre.
●
Screw the compressor tyre inator into the
valve.
●
Repeat the ination process.
●
If it still does not come up to pressure, the
tyre is too badly damaged. Stop and seek assis-
tance from authorised personnel.
●
Disconnect the air compressor. Unscrew the
tyre ination tube from the tyre valve.
●
When the tyre pressure is between 2.5 and
2.0 bars, continue driving without exceeding
80km/h (50 mph).
●
Attach the sticker ›››Fig.247
2
to the
instrument cluster display, within the driver's
eld of vision.
●
Check the pressure again after 10minutes
›››page389.
WARNING
When inating the wheel, the air compressor
and the inator tube may become hot.
●
Protect hands and skin from hot parts.
●
Do not place the hot exible inator tube
or hot air compressor on ammable material.
●
Allow them to cool before storing the de-
vice.
●
If it is not possible to inate the tyre to at
least 2.0bars (29psi / 200kPa), the tyre is
too badly damaged. The sealant is not in a
good condition to seal the tyre. Do not con-
tinue driving. Seek specialist assistance.
NOTICE
Switch o the air compressor after a maxi-
mum of 8 minutes of operation to avoid over-
heating! Before switching on the air com-
pressor again, let it cool for several minutes.
Check after 10 minutes of driving
Screw in the inator tube ›››
Fig.247
8
again
and check the pressure on the gauge
7
.
1.3bar (19psi / 130kPa) or lower:
●
Stop the vehicle! The tyre cannot be sealed
suiciently with the tyre mobility set.
●
You should obtain professional assistance
››› .
1.4 bar (20 psi/140 kPa) and higher:
●
Set the tyre pressure to the correct value
again.
●
Carefully resume your journey until you
reach the nearest specialised workshop with-
out exceeding 80km/h (50mph).
●
Have the damaged tyre replaced.
390
Wheels and tyres
WARNING
Driving with an unsealed tyre is dangerous
and can cause accidents and serious injury.
●
Do not continue driving if the tyre pressure
is 1.3bar (19psi / 130kPa) or lower.
●
Seek specialist assistance.

Related Topics

Popular Owner Manuals