2024-2026 Cupra Terramar SUV Wheels and tyres -> Tyre repair User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Wheels and tyres -> Tyre repair for Your Cupra Terramar SUV First Generation (2024-2026)

Wheels and tyres
387
Tyre repair
●
The tyre pressure monitoring indicator
does not function when there is a fault in the
ESC or ABS ›››
page189.
Troubleshooting
Low tyre pressure
The control lamp lights up in yellow.
The ination pressure of one or more wheels
is much lower than the value set by the driver,
or the tyre has structural damage. In addition,
a audible warning sounds and a text message is
displayed on the instrument cluster display.
●
Stop the vehicle! Stop the vehicle as
soon as possible in a safe place.
●
Check all tyres and pressures.
●
Replace any damaged tyres.
Fault in the tyre pressure loss indicator
The control lamp ashes for approximately 1
minute and then lights up permanently in yel-
low.
●
If the tyre is inated correctly, switch the ig-
nition o and on again.
●
Re-calibrate the tyre pressure monitoring
system ›››page385
●
If the fault continues, go to a specialised
workshop.
Tyre repair
TMS (Tyre Mobility System) punc-
ture repair kit
The puncture repair kit (Tyre Mobility System)
will reliably seal punctures caused by the pene-
tration of a foreign body of up to about 4 mm
in diameter. Do not remove foreign objects,
e.g. screws or nails, from the tyre.
After inserting the sealant residue in the tyre,
you must again check the tyre pressure about
10minutes after starting the engine.
You should only use the tyre mobility set if the
vehicle is parked in a safe place, you are famil-
iar with the procedure and you have the nec-
essary tyre mobility set. Otherwise, you should
seek professional assistance.
Tyre sealant must not be used in the follow-
ing cases:
●
If the wheel rim has been damaged.
●
In outside temperatures below -20°C (-4°F).
●
If the cut or punctures in the tyres are larger
than 4 mm.
●
If the tyre has been driven on with very low
ination pressure or no tyre pressure.
●
If the expiry date of the sealant bottle has
passed.
WARNING
Using the puncture repair kit can be danger-
ous, particularly when lling the tyre on the
roadside. To reduce the risk of serious injury,
consider the following:
●
Stop the vehicle as soon as possible in a
safe place. Park it at a safe distance from
road traic to ll the tyres.
●
Make sure the ground is at and rm.
●
All occupants, especially children, should
stay a safe distance away from the work area.
●
Turn on the hazard lights to warn other
road users.
●
Always switch o the engine and activate
the electronic parking brake to reduce the
risk of accidental vehicle movement.
–
Vehicles with automatic transmission:
switch on the parking lock P.
●
Use the puncture repair kit only if you are
familiar with the necessary operations. Oth-
erwise, you should seek professional assis-
tance.
●
The puncture repair kit should only be
used in an emergency, to reach the nearest
garage.
●
Replace tyres repaired with the puncture
kit as soon as possible.
388
Wheels and tyres
1
2
3
4
5
6
7
8
9
10
11
●
The sealant is harmful to health and must
be cleaned o immediately if it comes into
contact with the skin.
●
Always keep the puncture repair kit out of
the reach of children.
WARNING
A tyre lled with sealant does not have the
same driving properties as a conventional
tyre.
●
Never drive faster than 80km/h (50mph).
●
Avoid full throttle, braking heavily and cor-
nering at high speeds.
●
Drive for only 10 minutes at a maximum
speed of 80 km/h (50mph) and then check
the tyre.
For the sake of the environment
Dispose of used or expired tyre sealant in
accordance with the relevant legal require-
ments.
Note
You can purchase new bottles of tyre sealant
from CUPRA specialist dealers or any SEAT
network dealer.
Note
Take into account the separate instruction
manual provided by the tyre mobility system
manufacturer.
Tyre mobility system contents
Fig.247 Standard display: contents of the
tyre mobility system.
The tyre mobility system is located under-
neath the oor covering in the luggage com-
partment. Includes the following components
›››
Fig.247:
Valve insert remover
A sticker to be stuck to the instrument
cluster, in the driver's eld of view, as a
reminder of the advisable maximum speed
“max.80 km/h” or “max.50mph”
Filler tube with cap
Air compressor (depending on the version,
the model may vary).
ON/OFF switch
Air bleed screw (it can also be integrated in
the inator tube).
Warning provided by tyre pressure moni-
toring system (it can also be integrated in
the inator tube).
Tube for inating tyres
12 volt connector
Bottle of sealant
Spare tyre valve
The valve insert remover
1
has a gap at the
lower end for a valve insert. The valve insert
can only be screwed or unscrewed in this way.
This also applies to its replacement part
11
.
Sealing and inating a tyre
Sealing the tyre
●
Unscrew the tyre valve cap and insert. Use
the device ›››Fig.247
1
to remove the valve
cap. Place it on a clean surface.
●
Shake the tyre sealant bottle vigorously
›››
Fig.247
10
.
●
Screw the tyre ination hose ›››Fig.247
3
into the tyre sealant bottle. The bottle's seal
will break automatically.
Wheels and tyres
389
Tyre repair
●
Remove the ller cap ›››Fig.247
3
and
screw the open end of the tube into the tyre
valve.
●
With the bottle upside down, empty all of
the contents into the tyre.
●
Remove the bottle from the valve.
●
Replace the valve insert with the device
›››Fig.247
1
onto the tyre valve.
Inating the tyre
●
Screw the tyre ination tube of the compres-
sor ›››Fig.247
8
onto the tyre valve.
●
Check that the air evacuation screw is
closed ›››Fig.247
6
.
●
Start the engine and leave it running.
●
Attach the connector ›››Fig.247
9
to the
vehicle’s 12 volt power outlet ›››
page261.
●
Switch on the air compressor with the
ON/OFF switch ›››Fig.247
5
.
●
Keep the air compressor running until it
reaches a pressure of 2.0-2.5 bar (29-36psi/
200-250kPa). A maximum of 8 minutes.
●
Disconnect the air compressor.
●
If it does not reach the indicated pressure,
unscrew the tyre inater tube from the valve.
●
Move the vehicle 10m so that the sealant is
distributed throughout the tyre.
●
Screw the compressor tyre inator into the
valve.
●
Repeat the ination process.
●
If it still does not come up to pressure, the
tyre is too badly damaged. Stop and seek assis-
tance from authorised personnel.
●
Disconnect the air compressor. Unscrew the
tyre ination tube from the tyre valve.
●
When the tyre pressure is between 2.5 and
2.0 bars, continue driving without exceeding
80km/h (50 mph).
●
Attach the sticker ›››Fig.247
2
to the
instrument cluster display, within the driver's
eld of vision.
●
Check the pressure again after 10minutes
›››page389.
WARNING
When inating the wheel, the air compressor
and the inator tube may become hot.
●
Protect hands and skin from hot parts.
●
Do not place the hot exible inator tube
or hot air compressor on ammable material.
●
Allow them to cool before storing the de-
vice.
●
If it is not possible to inate the tyre to at
least 2.0bars (29psi / 200kPa), the tyre is
too badly damaged. The sealant is not in a
good condition to seal the tyre. Do not con-
tinue driving. Seek specialist assistance.
NOTICE
Switch o the air compressor after a maxi-
mum of 8 minutes of operation to avoid over-
heating! Before switching on the air com-
pressor again, let it cool for several minutes.
Check after 10 minutes of driving
Screw in the inator tube ›››
Fig.247
8
again
and check the pressure on the gauge
7
.
1.3bar (19psi / 130kPa) or lower:
●
Stop the vehicle! The tyre cannot be sealed
suiciently with the tyre mobility set.
●
You should obtain professional assistance
››› .
1.4 bar (20 psi/140 kPa) and higher:
●
Set the tyre pressure to the correct value
again.
●
Carefully resume your journey until you
reach the nearest specialised workshop with-
out exceeding 80km/h (50mph).
●
Have the damaged tyre replaced.
390
Wheels and tyres
WARNING
Driving with an unsealed tyre is dangerous
and can cause accidents and serious injury.
●
Do not continue driving if the tyre pressure
is 1.3bar (19psi / 130kPa) or lower.
●
Seek specialist assistance.

Related Topics

Popular Owner Manuals